VTech CS6114 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
User’s manual
CS6114
CS6114-11
CS6114-2
DECT 6.0 cordless telephone
Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
S
m
For more support information
Congratulations
on purchasing your new VTech product.
Before using this telephone, please read
Important safety instructions.
This manual has all the feature operations
and troubleshooting necessary to install
and operate your new VTech telephone.
Please review this manual thoroughly to
ensure proper installation and operation
of this innovative and feature rich VTech
product.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com. In Canada, please
visit phones.vtechcanada.com/.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identified with
this logo have reduced noise
and interference when used
with most T-coil equipped
hearing aids and cochlear
implants. The TIA-1083
Compliant Logo is a trademark
of the Telecommunications
Industry Association. Used
under license.
Important safety instructions
When using your telephone equipment,
basic safety precautions should always be
followed to reduce the risk of fire, electric
shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Unplug this product from the wall
outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this product near water
such as near a bath tub, wash
bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement
or shower.
5. Do not place this product on an
unstable table, shelf, stand or other
unstable surfaces.
6. Avoid placing the telephone system
in places with extreme temperature,
direct sunlight, or other electrical
devices. Protect your phone from
moisture, dust, corrosive liquids and
fumes.
7. Slots and openings in the back or
bottom of the telephone base and
handset are provided for ventilation.
To protect them from overheating,
these openings must not be blocked
by placing the product on a soft
surface such as a bed, sofa or rug. This
product should never be placed near
or over a radiator or heat register. This
product should not be placed in any
area where proper ventilation is not
provided.
8. This product should be operated
only from the type of power source
indicated on the marking label. If you
are not sure of the type of power
supply in your home or office, consult
your dealer or local power company.
9. Do not allow anything to rest on the
power cord. Do not install this product
where the cord may be walked on.
10. Never push objects of any kind into
this product through the slots in the
telephone base or handset because
they may touch dangerous voltage
points or create a short circuit. Never
spill liquid of any kind on the product.
11. To reduce the risk of electric shock,
do not disassemble this product, but
take it to an authorized service facility.
Opening or removing parts of the
telephone base or handset other than
specified access doors may expose
you to dangerous voltages or other
risks. Incorrect reassembling can cause
electric shock when the product is
subsequently used.
12. Do not overload wall outlets and
extension cords.
13. Unplug this product from the wall
outlet and refer servicing to an
authorized service facility under the
following conditions:
When the power supply cord or
plug is damaged or frayed.
If liquid has been spilled onto the
product.
If the product has been exposed to
rain or water.
If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operation instructions. Improper
adjustment of other controls may
result in damage and often requires
extensive work by an authorized
technician to restore the product to
normal operation.
If the product has been dropped
and the telephone base and/or
handset has been damaged.
If the product exhibits a distinct
change in performance.
14. Avoid using a telephone (other than
cordless) during an electrical storm.
There is a remote risk of electric shock
from lightning.
15. Do not use the telephone to report
a gas leak in the vicinity of the leak.
Under certain circumstances, a spark
may be created when the adapter
is plugged into the power outlet,
or when the handset is replaced in
its cradle. This is a common event
associated with the closing of any
electrical circuit. The user should
not plug the phone into a power
outlet, and should not put a charged
handset into the cradle, if the phone is
located in an environment containing
concentrations of flammable or
flame-supporting gases, unless there
is adequate ventilation. A spark in
such an environment could create a
fire or explosion. Such environments
might include: medical use of oxygen
without adequate ventilation; industrial
gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
16. Only put the handset of your
telephone next to your ear when it is in
normal talk mode.
17. The power adapter is intended to be
correctly oriented in a vertical or floor
mount position. The prongs are not
designed to hold the plug in place if
it is plugged into a ceiling, under-the-
table or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire.
Check with local waste management
The ENERGY STAR
®
program
(www.energystar.gov)
recognizes and encourages
the use of products that save
energy and help protect our
environment. We are proud
to mark this product with the
ENERGY STAR® label indicating
it meets the latest energy
efficiency guidelines.
codes for special disposal instructions.
Do not open or mutilate the battery.
Released electrolyte is corrosive and
may cause burns or injury to the eyes
or skin. The electrolyte may be toxic if
swallowed.
Exercise care in handling batteries in
order not to create a short circuit with
conductive materials.
Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in
this manual.
Precautions for users of implanted
cardiac pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC
(WTR), an independent research entity,
led a multidisciplinary evaluation of the
interference between portable wireless
telephones and implanted cardiac
pacemakers. Supported by the U.S.
Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least
six inches from the pacemaker.
Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
Should use the wireless telephone at the
ear opposite the pacemaker.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless telephones.
About cordless telephones
Privacy: The same features that make a
cordless telephone convenient create
some limitations. Telephone calls are
transmitted between the telephone
base and the cordless handset by radio
waves, so there is a possibility that
the cordless telephone conversations
could be intercepted by radio receiving
equipment within range of the
cordless handset. For this reason, you
should not think of cordless telephone
conversations as being as private as
those on corded telephones.
Electrical power: The telephone base
of this cordless telephone must be
connected to a working electrical outlet.
The electrical outlet should not be
controlled by a wall switch. Calls cannot
be made from the cordless handset
if the telephone base is unplugged,
switched off or if the electrical power is
interrupted.
Potential TV interference: Some
cordless telephones operate at
frequencies that may cause interference
to televisions and VCRs. To minimize or
prevent such interference, do not place
the telephone base of the cordless
telephone near or on top of a TV or
VCR. If interference is experienced,
moving the cordless telephone farther
away from the TV or VCR often reduces
or eliminates the interference.
Rechargeable batteries: Exercise care in
handling batteries in order not to create
a short circuit with conducting material
such as rings, bracelets and keys. The
battery or conductor may overheat and
cause harm. Observe proper polarity
between the battery and the battery
charger.
Nickel-metal hydride rechargeable
batteries: Dispose of these batteries in
a safe manner. Do not burn or puncture
the battery. Like other batteries of this
type, if burned or punctured, they
could release caustic material which
could cause injury.
i
Table of contents
Important safety instructions ................... II
What’s in the box .......................................1
Overview.....................................................2
Handset overview ........................................ 2
Telephone base overview ........................... 3
Charger overview ........................................ 3
Display icons overview ................................ 3
Connect ......................................................3
Connect the telephone base ....................... 3
Connect the charger .................................... 4
Mount the telephone base........................... 4
Install and charge the battery ...................... 4
Before use .................................................. 5
Set date and time ........................................ 5
Check for dial tone ...................................... 5
Congure your telephone .........................6
Use the handset menu ................................ 6
Set language ............................................... 6
Set date and time ........................................ 6
Operating range .......................................... 6
Dial mode .................................................... 7
Temporary tone dialing ................................ 7
Telephone operations ...............................8
Make a call .................................................. 8
Predial a call ................................................ 8
Answer a call ............................................... 8
End a call: .................................................... 8
Volume ........................................................ 8
Mute ............................................................ 8
Call waiting .................................................. 9
Chain dialing ................................................ 9
Find handset.............................................. 10
Redial list..................................................10
Review a redial list entry ........................... 10
Dial a redial list entry ................................. 10
Delete a redial list entry ............................. 10
Directory ...................................................10
Add a directory entry ..................................11
Review a directory entry .............................11
Alphabetical search ....................................11
Delete a directory entry ..............................11
Edit a directory entry ................................. 12
Dial a directory entry ................................. 12
Caller ID .................................................... 12
Review a caller ID log entry ...................... 13
Memory match........................................... 13
Missed call indicator .................................. 13
View dialing options................................... 13
Dial a caller ID log entry ............................ 13
Save a caller ID log entry to the directory . 14
Delete the caller ID log entries .................. 14
Sound settings .........................................14
Key tone .................................................... 14
Ringer tone ................................................ 14
Ringer volume ........................................... 15
Temporary ringer silencing ........................ 15
Retrieve voicemail from telephone service
15
Retrieve voicemail ..................................... 15
Turn off the new voicemail indicators ........ 16
Register a handset ..................................16
Screen messages ....................................16
General product care ..............................18
Frequently asked questions ................... 18
The RBRC® seal .......................................21
FCC, ACTA and IC regulations ...............21
California Energy Commission battery
charging testing instructions ............23
For C-UL compliance only ...................... 24
Mesures de sécurité importantes .............. 24
Limited warranty ......................................27
Disclaimer and Limitation of Liability ....29
Technical specications ......................... 29
1
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in the event
warranty service is necessary.
NOTE
To purchase a replacement battery or power
adapter, visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com/ or call
1 (800) 267-7377.
1 set for CS6114/CS6114-11;
2 sets for CS6114-2
1 set for CS6114/CS6114-11/
CS6114-2
1 set for CS6114/CS6114-11/
CS6114-2
1 set for CS6114-2
Abridged
user’s
manual
Important
safety
instructions
2 3
Overview
Handset overview
1 – Handset earpiece
2 – LCD display
3 – CID/VOL-
Review the caller ID log when the
telephone is not in use.
Scroll down while in a menu, or in the
directory, caller ID log or redial list.
Move the cursor to the left when
entering numbers or names.
Decrease the listening volume during a
call.
4 – /FLASH
Make or answer a call.
Answer an incoming call when you
receive a call waiting alert.
5 – 1
Press repeatedly to add or remove 1 in
front of the caller ID log entry before
dialing or saving it to the directory.
6 – TONE
Switch to tone dialing temporarily
during a call.
7 – MUTE/DELETE
Mute the microphone during a call.
Telephone base overview
1 – /FIND HANDSET
Page all system handsets.
2 – Charging pole
Charger overview
1 – Charging pole
Display icons overview
The battery icon flashes when
the battery is low and needs
charging.
The battery icon animates
when the battery is charging.
The battery icon becomes
solid when the battery is fully
charged.
There are new voicemail
received from your telephone
service provider.
NEW There are new caller ID log
entries.
Connect
You can choose to connect the telephone
base for desktop usage or wall mounting.
NOTES
Use only the adapters provided.
Make sure the electrical outlets are not
controlled by wall switches.
The adapters are intended to be correctly
oriented in a vertical or floor mount position.
The prongs are not designed to hold the
plug in place if it is plugged into a ceiling,
under-the-table or cabinet outlet.
TIP
If you subscribe to digital subscriber line
(DSL) high-speed Internet service through
your telephone line, make sure you install
a DSL filter (not included) between the
telephone line cord and telephone wall jack.
Contact your DSL service provider for more
information.
Connect the telephone base
Silence the handset ringer temporarily
while the phone is ringing.
Delete the displayed entry while
reviewing the directory, caller ID log or
redial list.
Delete digits or characters when
entering numbers or names.
8 – Microphone
9 – Charging pole
10 – MENU/SELECT
Show the menu.
While in a menu, press to select an item,
or save an entry or setting.
11 – /VOL+
Review the directory when the phone is
not in use.
Scroll up while in a menu, or in the
directory, caller ID log or redial list.
Move the cursor to the right when
entering numbers or names.
Increase the listening volume during a
call.
12 – OFF/CANCEL
Hang up a call.
Return to the previous menu or idle
mode without making changes.
Delete digits while predialing.
Silence the handset ringer temporarily
while the phone is ringing.
Erase the missed call indicator while the
handset is not in use.
13 – 0/OPER
Enter space character during text
editing.
14 – #
Show other dialing options when
reviewing a caller ID log entry.
15 – REDIAL/PAUSE
Review the redial list.
Insert a dialing pause while dialing or
entering numbers into the directory.
16 – Battery compartment cover
4 5
Charge the battery
Place the handset in the telephone
base or the charger to charge.
Once you have installed the battery, the
handset LCD display indicates the battery
status (see the following table).
NOTES
For best performance, keep the handset in
the telephone base or charger when not in
use.
The battery is fully charged after 16 hours of
continuous charging.
If you place the handset in the telephone
base or the charger without plugging in the
battery, the screen displays No battery.
Connect the charger
Mount the telephone base
Install and charge the battery
Install the battery
Install the battery as shown below.
NOTES
Use only supplied battery.
Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
If the handset will not be used for a long
time, disconnect and remove the battery to
prevent possible leakage.
Battery
indicators Battery
status Action
The screen
is blank, or
displays Put in
charger and
flashes.
The battery
has no or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(at least 30
minutes).
The screen
displays
Low battery
and flashes.
The battery
has enough
charge to be
used for a
short time.
Charge
without
interruption
(about 30
minutes).
The screen
displays
HANDSET X.
The battery
is charged. To keep
the battery
charged,
place it in the
telephone
base or
charger when
not in use.
When the battery is fully charged, you can
expect the following performance:
Operation Operating
time
While in use (talking*) Seven hours
While not in use (standby**) Five days
* Operating times vary depending on your
actual use and the age of the battery.
** Handset is not charging nor in use.
Before use
After you install your telephone or power
returns following a power outage, the
handset will prompt you to set the date
and time.
Set date and time
1. Use the dialing keys (0-9) to enter the
month (MM), date (DD) and year (YY).
Then press SELECT.
2. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press q or p to choose AM or PM.
3. Press SELECT to save.
Check for dial tone
Press . If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone:
Make sure the installation procedures
described above are properly done.
It may be a wiring problem. If you have
changed your telephone service to
digital service from a cable company or
a VoIP service provider, the telephone
line may need to be rewired to allow
all existing telephone jacks to work.
Contact your cable/VoIP service
provider for more information.
THIS SIDE UP
6 7
Dial mode
The dial mode is preset to touch-tone
dialing. If you have pulse (rotary) service,
you need to change the dial mode to
pulse dialing before using the telephone.
1. Press MENU when the handset is not
in use.
2. Press q or p to choose Settings, and
then press SELECT.
3. Press q or p to choose Dial mode,
then press SELECT.
4. Press or to choose Touch-tone or
Pulse, then press SELECT to confirm
your selection. You hear a confirmation
tone.
Temporary tone dialing
If you have pulse (rotary) service only,
you can switch from pulse to touch-tone
dialing temporarily during a call. This is
useful if you need to send touch-tone
signals to access your telephone banking
or long distance services.
1. During a call, press TONE .
2. Use the dialing keys to enter the
number. The telephone sends touch-
tone signals. It automatically returns to
pulse dialing mode after you end the
call.
Operating range
This cordless telephone operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even
so, this handset and telephone base can
communicate over only a certain distance
- which can vary with the locations of the
telephone base and handset, the weather,
and the layout of your home or office.
When the handset is out of range, the
handset displays Out of range or no pwr
at base.
If there is a call while the handset is out of
range, it may not ring, or if it does ring, the
call may not connect well when you press
. Move closer to the telephone base,
then press to answer the call.
If the handset moves out of range during
a telephone conversation, there may be
interference. To improve reception, move
closer to the telephone base.
Configure your telephone
Use the handset menu
1. Press MENU when the phone is not in
use.
2. Press or until the screen displays
the desired feature menu.
3. Press SELECT.
To return to the previous menu, press
CANCEL.
To return to idle mode, press and hold
CANCEL.
Set language
The LCD language is preset to English. You
can select English, French or Spanish to be
used in all screen displays.
1. Press MENU when the handset is not
in use.
2. Press q or p to choose Settings and
then press SELECT twice.
3. Press q or p to choose English,
Français or Español.
4. Press SELECT twice to save your
setting. You hear a confirmation tone.
Set date and time
1. Press MENU on the handset when not
in use.
2. Press q or p to choose Set
date/time and then press SELECT.
3. Use the dialing keys (0-9) to enter the
month (MM), date (DD) and year (YY).
Then press SELECT.
4. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press q or p to choose AM or PM.
5. Press SELECT to save your setting. Your
hear a confirmation tone.
8 9
Telephone operations Call waiting
When you subscribe to call waiting service
from your telephone service provider, you
hear an alert tone if there is an incoming
call while you are already on a call.
Press FLASH to put the current call on
hold and take the new call.
Press FLASH at any time to switch back
and forth between calls.
If you also subscribe to caller ID service, it
will let you see the name and telephone
number of the caller during call waiting.
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provide if:
You have both caller ID and call waiting,
but as separate service (you may need
to combine these service);
You have only caller ID service, or only
call waiting service; or
You do not subscribe to caller ID or call
waiting services.
There are fees for caller ID services. In
addition, services may not be available in
all areas.
Chain dialing
Use this feature to initiate a dialing
sequence from numbers stored in the
directory, caller ID log or redial while you
are on a call.
Chain dialing can be useful if you wish
to access other numbers (such as bank
account numbers or access codes) from
the directory, caller ID log or redial list.
To access a number in the directory
while on a call:
1. Press MENU/SELECT twice to enter the
directory.
2. Press q or p to scroll to the desired
entry.
3. Press SELECT to dial the displayed
Handset control key panel:
CANCEL
CANCEL
Make a call
Press , and then dial the telephone
number.
NOTES
The screen shows the elapsed time as you
talk (in hours, minutes and seconds).
If the handset is moved out of range while
on a call, it will beep three times.
Predial a call
Enter the telephone number using
the dialing keys (0-9), then press to
dial.
When predialing (preview numbers
before dialing), press DELETE or CANCEL
to backspace and delete; press and hold
PAUSE to insert a dialing pause (a P appears).
Answer a call
Press or any of the dialing keys.
End a call:
Press OFF or put the handset back in the
telephone base or charger.
Volume
During a call, press VOL- or VOL+ to
adjust the listening volume.
Mute
The mute function allows you to hear the
other party but the other party cannot hear
you.
1. During a call, press MUTE. The handset
displays Muted.
2. Press MUTE again to resume the
conversation. The handset displays
Microphone on briefly.
number.
To access a number in the caller ID log
while on a call:
1. Press MENU and then press q or p to
select Caller ID log.
2. Press SELECT and then press q or p
to scroll to the desired entry.
3. Press SELECT to dial the displayed
number.
To access a number in the redial list
while on a call:
1. Press REDIAL.
2. Press q, p or REDIAL repeatedly to
browse to the desired entry.
3. Press SELECT to dial the displayed
number.
NOTES
You cannot edit a directory entry while on a
call. Refer to the Directory section for more
details.
You cannot copy a caller ID log entry into the
directory while on a call. Refer to the Caller
ID log section for more details.
You cannot erase a redial entry while on a
call. Refer to the Redial list section for more
details.
Press CANCEL to exit redial, directory or
caller ID log when you are on a call.
10 11
Find handset
Use this feature to find the system handset.
To start paging:
Press /FIND HANDSET on the
telephone base when not in use.
All idle handsets ring and display
** Paging **.
To end paging:
Press /FIND HANDSET at the
telephone base.
-OR-
Press or any of the dialing keys on
the handset.
NOTES
Press MUTE to turn off the ringer of a
handset temporarily. Paging tone continues
on the other handset.
Do not press and hold /FIND HANDSET
for more than four seconds. It may lead
to handset deregistration. If the handset
displays To register HS and See manual,
refer to the Register a handset section to
register the handset back to the telephone
base.
Redial list
Each handset stores the last five telephone
numbers dialed. Entries are shown in
reverse chronological order. When there
are already five entries, the oldest entry is
deleted to make room for the new entry.
Review a redial list entry
1. Press REDIAL when the handset is not
in use.
2. Press q, p or REDIAL repeatedly until
the desired entry displays.
Add a directory entry
1. Enter the number when the phone is
not in use. Press MENU, then go to
Step 3.
-OR-
Press MENU when the phone is not
in use, then press SELECT to choose
Directory. Press SELECT again to
choose Add contact.
2. When Enter number
displays, use the
dialing keys to enter
the number.
-OR-
Copy a number from the redial list
by pressing REDIAL and then press
q, p or REDIAL repeatedly to select
a number. Press SELECT to copy the
number.
3. Press SELECT to move
on to enter the name.
The handset displays
Enter name.
4. Use the dialing keys to enter the
name. Additional key presses show
other characters of that particular key.
The first character of every word is
capitalized.
5. Press SELECT to save. The handset
displays Saved and then you hear a
confirmation tone.
While entering names and numbers, you
can:
Press DELETE to backspace and erase a
digit or character.
Press and hold DELETE to erase the
entire entry.
Press q or p to move the cursor to the
left or right.
Press and hold PAUSE to insert a dialing
pause (for entering numbers only).
Press 0 to add a space (for entering
names only).
Dial a redial list entry
1. Press REDIAL when the handset is not
in use.
2. Press q, p or REDIAL repeatedly until
the desired entry displays.
3. Press to dial.
-OR-
1. Press when the handset is not in
use.
2. Press REDIAL and then press q, p or
REDIAL repeatedly until the desired
entry displays.
3. Press SELECT to dial.
Delete a redial list entry
1. Press REDIAL when the handset is not
in use.
2. Press q, p or REDIAL repeatedly to
browse to the desired entry.
3. Press DELETE to delete the displayed
number. You hear a confirmation tone.
Directory
The directory can store up to 30 entries,
which are shared by all handsets. Each
entry may consist of a telephone number
up to 30 digits, and a name up to
15 characters.
Each handset directory is independent
(for multiple handset models only). Any
additions, deletions or edits made on
one handset are not reflected on other
handsets.
If the telephone number in the directory
exceeds 15 digits, a dash appears after
the 14th digit and then the remaining
digits are shown beginning with a dash,
alternately.
Review a directory entry
Entries are sorted alphabetically.
1. Press when the phone is not in use.
2. Press q or p to browse through the
directory, or use the dialing keys to
start a name search.
-OR-
1. Press MENU when the handset is not
in use.
2. Press SELECT to choose Directory.
3. Press q or p to scroll to Review and
then press SELECT.
4. Press q or p to
browse.
Alphabetical search
1. Follow the steps in Review a directory
entry above to enter the directory.
2. Use the dialing keys to enter the
letter associated with the name. For
example, if you have entries for Jenny,
Jessie, Kristen and Laura in your
directory, press 5 (JKL) once to see
Jenny (when Jenny displays, press
q to see Jessie), twice to see Kristen,
or three times to see Laura. If there is
no name entry matching your search,
the next closest match in alphabetical
order appears. If necessary, press q or
p to browse.
Delete a directory entry
1. Search for the desired entry in the
directory (see Review a directory
entry or Alphabetical search).
2. When the desired entry appears, press
DELETE. The handset displays Delete
contact? and the number.
3. Press SELECT to confirm. The handset
displays Deleting ... and then Contact
deleted. You hear a confirmation tone.
Enter number
_
Enter name
Review
p
q
12 13
Edit a directory entry
1. Search for the desired entry in the
directory (see Review a directory
entry or Alphabetical search).
2. When the desired entry appears, press
SELECT. The handset displays Edit
number and the stored number.
3. Use the dialing keys to edit the
number, then press SELECT. The
handset displays Edit name and then
the stored name.
4. Use the dialing keys to enter the
name. Additional key presses show
other characters of that particular key.
The first character of every word is
capitalized.
5. Press SELECT to save. The handset
displays Saved and then you hear a
confirmation tone.
Dial a directory entry
1. Search for the
desired entry in the
directory (see Review
a directory entry or
Alphabetical search).
2. When the desired
entry appears, press
to dial.
Review a caller ID log entry
1. Press CID when the phone is not in
use.
2. Press q or p to browse through the
caller ID log.
-OR-
1. Press MENU when the phone is not in
use. Press q or p to select Caller ID
log.
2. Press SELECT twice and then press q
or p to browse.
NOTE
You hear two beeps when you reach the
beginning or end of the caller ID log.
Memory match
When the incoming telephone number
matches the last seven digits of a
telephone number in your directory, the
screen displays the stored name of the
directory entry.
For example, if Linda Jones calls, her name
appears as Linda if this is how you entered
it into your directory.
The number shown in the caller ID log
is in the format sent by the telephone
service provider. It usually delivers 10-digit
telephone numbers (area code plus phone
number). If the last seven digits of the
incoming telephone number does not
match a number in your directory, the name
appears as it is delivered by the telephone
service provider.
Missed call indicator
When there are calls that have not been
reviewed in the caller ID log, the handset
displays XX missed calls.
Each time you review a caller ID log entry
marked NEW, the number of missed calls
decreases by one.
When you have reviewed all the missed
calls, the missed call indicator no longer
displays.
Caller ID
If you subscribe to caller ID service,
information about each caller appears after
the first or second ring. If you answer a call
before the caller information appears on
the screen, it will not be saved in the caller
ID log.
The caller ID log stores up to 30 entries.
Each entry has up to 24 digits for the
phone number and 15 characters for the
name.
If the telephone number has more that 15
digits, only the last 15 digits appear.
If the name has more than 15 characters,
only the first 15 characters are shown and
saved in the caller ID log.
Entries appear in reverse chronological
order. When the caller ID log is full, the
oldest entry is deleted to make room for
new incoming call information.
Caller ID log entries are shared by all
system handsets (for multiple handset
models only). Any deletions made on
one handset are reflected on all other
handsets.
This product can provide information
only if both you and the caller are in areas
offering caller ID service and if both
telephone service providers use compatible
equipment. The time and date are sent by
your telephone service provider along with
the call information.
If you do not want to review the missed
calls one by one, press and hold CANCEL
on the idle handset to erase the missed
call indicator. All the entries are then
considered old.
View dialing options
Although the caller ID log entries received
have 10 digits (the area code plus the
seven-digit number), in some areas, you
may dial a 1 plus the area code plus the
seven digits. You can change the number
of digits that you dial from or store to the
directory.
While reviewing the caller ID log, press #
(pound key) repeatedly to show different
dialing options for local and long distance
numbers before dialing or saving the
telephone number in the directory.
Press 1 repeatedly if you need to add or
remove 1 in front of the telephone number
before dialing or saving it in the directory.
Press # 1-800-595-9511
Press # 595-9511
Press # 1-595-9511
Press # 800-595-9511
-OR-
Press 1 1-800-595-9511
Press 1 800-595-9511
Mike Smith
800-595-9511
10:15 PM
12/25
NOTE
7-digit local dialing
will be invalid from
October 2021 onwards. Press # (pound key)
repeatedly to select the appropriate dialing
option.
Dial a caller ID log entry
When the number is shown in the correct
format for dialing, press to dial.
Mike Smith
800-595-9511
Delete contact?
800-595-9511
XX missed calls
10:15 PM
12/25
Mike Smith
595-9511
10:15 PM
12/25
NEW
14 15
Save a caller ID log entry to the
directory
1. When in the caller ID log, press q or
p to browse.
2. When the desired caller ID log entry
displays, press SELECT. The handset
displays Edit number and the stored
number.
3. Use the dialing keys to modify the
number, if necessary. Then press
SELECT. The handset displays Edit
name and then the stored name.
4. Use the dialing keys to modify the
name, if necessary. Then press SELECT.
The handset displays Saved and then
you hear a confirmation tone.
While entering names and numbers, you
can:
Press DELETE to backspace and erase a
digit or character.
Press and hold DELETE to erase the
entire entry.
Press q or p to move the cursor to the
left or right.
Press and hold PAUSE to insert a dialing
pause (for entering numbers only).
Press 0 to add a space (for entering
names only).
Delete the caller ID log entries
1. When in the caller ID log, press q or
p to browse.
2. When the desired caller ID log entry
displays, press DELETE. You hear a
confirmation tone.
through the choices.
5. Press SELECT to save. You hear a
confirmation tone.
If you turn off the ringer volume, you will not
hear ringer tone samples.
Ringer volume
You can adjust the ringer volume level, or
turn the ringer off.
1. Press MENU when the handset is not
in use.
2. Press q or p to choose Ringers and
then press SELECT twice.
3. The screen displays Volume: with the
current setting flashing. Press q or p
to choose a volume level. A sample of
each ringer volume plays as you scroll
through the choices.
4. Press SELECT to save. You hear a
confirmation tone.
NOTES
If the ringer volume is set to Off, the idle
screen displays Ringer off.
When the ringer volume is set to Off, the
handset still rings when you press /FIND
HANDSET at the telephone base.
To delete all caller ID log entries:
1. Press MENU when the phone is not in
use.
2. Press q or p to select Caller ID log
and then press SELECT.
3. Press q or p to
select Del all calls
then press SELECT.
4. The screen displays
Delete all?. Press
SELECT to confirm.
The handset displays
Deleting... and then
you hear a confirmation tone.
Sound settings
Key tone
You can turn the key tone on or off.
1. Press MENU when the handset is not
in use.
2. Press q or p to choose Settings and
then press SELECT.
3. Press q or p to choose Key tone, then
press SELECT.
4. Press q or p to choose On or Off,
then press SELECT to save. You hear a
confirmation tone.
Ringer tone
You can choose from different ringer tones
for each handset.
1. Press MENU when the handset is not
in use.
2. Press q or p to choose Ringers and
then press SELECT.
3. Press q or p to choose Ringer tone,
then press SELECT.
4. The screen displays Tone: with the
current setting flashing. Press q or p
to choose a ringer tone. A sample of
each ringer tone plays as you scroll
Temporary ringer silencing
When the telephone is ringing, you can
temporarily silence the ringer without
disconnecting the call. The next call rings
normally at the preset volume.
To silence the handset ringer:
Press CANCEL or MUTE. The handset
displays Ringer muted.
Retrieve voicemail from
telephone service
Voicemail is a feature available from most
telephone service providers. It may be
included with your telephone service, or
may be optional. Fees may apply.
Retrieve voicemail
When you received a
voicemail, the handset
displays and New
voicemail.
To retrieve, you typically
dial an access number provided by your
telephone service provider, and then enter
a security code. Contact your telephone
service provider for instructions on how to
configure the voicemail settings and listen
to messages.
NOTE
After you have listened to all new voicemail
messages, the indicators on the handset turn
off automatically.
Del all calls
p
q
Delete all?
New voicemail
10:15 PM
12/25
16 17
Turn off the new voicemail
indicators
If you have retrieved your voicemail while
away from home, and the handset still
displays the new voicemail indicators, use
this feature to turn off the indicators.
NOTE
This feature turns off the indicators only, it
does not delete your voicemail messages.
1. Press MENU when the phone is not in
use.
2. Press q or p to choose Settings and
then press SELECT.
3. Press q or p to choose Clr voicemail
and then press SELECT.
4. The screen displays Reset VM Icon?.
Press SELECT to confirm. You hear a
confirmation tone.
Register a handset
When your handset is deregistered from
the telephone base, follow the steps
below to register it back to the telephone
base.
1. Remove the handset from the
telephone base.
2. Press and hold /FIND HANDSET at
the telephone base for about four
seconds until the IN USE light turns on.
3. Then press # on the handset. It
displays Registering...
The handset show Registered and you
hear a beep when the registration process
completes. The registration process takes
Not
available
One handset is already
reviewing the caller ID
log and the other handset
tries to review it.
Number
repeated
The telephone number
you enter is already
stored in the directory.
Out of
range or
no pwr at
base
The handset cannot
communicate with the
telephone base. Check
the telephone base
power connection or
move the handset closer
to the telephone base.
Phone
X:XX:XX
The handset is on a call.
PRIVATE
NAME
The caller is blocking the
name information.
PRIVATE
NUMBER
The caller is blocking
the telephone number
information.
about 60 seconds to complete.
Screen messages
Call log
empty
There are no caller ID log
entries.
Directory
empty
There are no directory
entries.
Directory
full
The directory is full.
Ended
X:XX:XX
You have just ended a
call.
Incoming
call
There is an incoming call.
Line in
use
A system handset is in use,
or another telephone on
the same line is in use.
LONG
DISTANCE
or L (before the
caller’s number)
It is a long distance call.
Low
battery
The battery needs to be
recharged.
Microphone
on
MUTE is turned off and
the person on the other
end can hear you.
Muted You have turned off the
handset microphone. The
other party cannot hear
you but you can hear the
other party.
New
voicemail
There are new voicemail
message(s) from the
telephone service
provider.
No battery No battery is installed.
Follow the directions
for battery installation
on page 4 to install the
battery before charging.
No line There is no telephone line
connected.
Clr voicemail
p
q
18 19
PRIVATE
CALLER
The caller is blocking the
name and the telephone
number information.
Put in
charger
The battery is very low.
Place the handset in
the telephone base or
charger for recharging.
Ringer
muted
The handset ringer is
muted temporarily during
an incoming call.
Ringer off The handset ringer is
turned off.
Saved Your selection has been
saved.
Unable to
call.
Failed phone call (the
other handset is in use).
UNKNOWN
NAME
This caller’s name is
unavailable.
UNKNOWN
NUMBER
This caller’s number is
unavailable.
UNKNOWN
CALLER
No caller information is
available about this caller.
XX missed
calls
There are calls that have
not been reviewed in the
caller ID log.
** Paging
**
The system handsets are
being paged.
General product care
Taking care of your telephone
Your cordless telephone contains
sophisticated electronic parts, so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets
wet. Do not use the handset outdoors in
the rain, or handle it with wet hands. Do
not install the telephone base near a sink,
The display
shows No line. I
cannot hear the
dial tone.
Disconnect the telephone
line cord from your
telephone and connect
it to another telephone.
If there is no dial tone
on that other telephone
either, then the telephone
line cord may be
defective. Try installing a
new telephone line cord.
If changing the telephone
line cord does not help,
the wall jack (or the wiring
to this wall jack) may
be defective. Contact
your telephone service
provider.
You may be using a new
cable or VoIP service, the
existing telephone jacks in
your home may no longer
work. Contact your service
provider for solutions.
I cannot dial out. Make sure there is a dial
tone before dialing. It
is normal if the handset
takes a second or two
to synchronize with the
telephone base before
producing a dial tone.
Wait an extra second
before dialing.
Eliminate any background
noise. Mute the handset
before dialing, or dial
from another room in
your home with less
background noise.
bathtub or shower.
Electrical storms
Electrical storms can sometimes cause
power surges harmful to electronic
equipment. For your own safety, take
caution when using electrical appliances
during storms.
Cleaning your telephone
Your telephone has a durable plastic casing
that should retain its luster for many years.
Clean it only with a dry non-abrasive cloth.
Do not use dampened cloth or cleaning
solvents of any kind.
Frequently asked questions
Below are the questions most frequently
asked about the cordless telephone. If you
cannot find the answer to your question,
visit our website at
www.vtechphones.com or call
1 (800) 595-9511 for customer service.
My telephone
does not work
at all.
Make sure the telephone
base is installed properly,
and battery is installed
and charged correctly.
For optimum daily
performance, return the
handset to the telephone
base after use.
The display
shows To
register HS and
See manual
alternately. The
handset does
not work at all.
The handset is
deregistered from the
telephone base. Follow
the steps in Register a
handset to register the
handset back to the
telephone base.
The display
shows Low
battery.
Place the handset in the
telephone base or charger
for charging.
The battery
does not charge
in the handset
or the handset
battery does not
accept charge.
Make sure the handset is
placed in the telephone
base or charger correctly.
If the battery is completely
depleted, charge the
battery for at least
30 minutes before use.
You may need to purchase
a new battery.
The telephone
does not ring
when there is an
incoming call.
Make sure the ringer
volume is not set to off.
The handset may be too
far from the telephone
base. Move it closer to the
telephone base.
My handset
beeps and is
not performing
normally.
Move the handset closer
to the telephone base. It
may be out of range.
I hear noise on
the cordless
handset and
the keys do not
work.
Make sure the telephone
line cord is plugged in
securely.
I hear other calls
when using the
telephone.
Disconnect the telephone
base from the telephone
wall jack. Plug in a
different telephone. If you
still hear other calls, the
problem is probably in
the wiring or telephone
service. Contact your
telephone service
provider.
20 21
There is
interference
during a
telephone
conversation.
My calls fade
out when
I am using
the cordless
handset.
The handset may be out
of range. Move it closer to
the telephone base.
If you subscribe to high-
speed Internet service
(DSL - digital subscriber
line) through your
telephone line, you must
install a DSL filter between
the telephone line cord
and the telephone wall
jack. The filter prevents
noise and caller ID
problems caused by DSL
interference. Contact your
DSL service provider for
more information about
DSL filters.
Appliances or other
cordless telephones
plugged into the
same circuit as the
telephone base can
cause interference. Try
moving the appliance or
telephone base to another
outlet.
The location of your
telephone base can
impact the performance
of your cordless phone.
For better reception,
install the telephone base
in a centralized location
within your home or
office, away from walls
or other obstructions.
In many environments,
elevating the telephone
base improves overall
performance.
I subscribe to a
nontraditional
telephone
service that uses
my computer
to establish
connections,
and my
telephone
doesn’t work.
Make sure your computer
is powered on, and
your Internet is working
properly.
Make sure to plug your
USB telephone adapter
into a dedicated USB port
on your computer. Do not
plug into a multiple port
USB hub (USB splitter) that
is not powered.
In a few rare instances,
the USB port on your
computer may not have
enough power. In these
instances, try using a USB
hub with its own external
power supply.
If you are using a firewall,
it may prevent access
to your nontraditional
telephone service. Contact
your service provider for
more information.
I accidentally
set my LCD
language to
Spanish or
French, and I
don’t know how
to change it
back to English.
While the handset is not in
use, press MENU and then
enter 364# to change
the handset LCD language
back to English.
The RBRC® seal
The RBRC® seal on the nickel-metal
hydride battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program to
collect and recycle these batteries at the
end of their useful lives, when taken out
of service within the United States and
Canada.
The RBRC® program provides a convenient
alternative to placing used nickel-
metal hydride batteries into the trash or
municipal waste, which may be illegal in
your area.
VTech’s participation in RBRC® makes it
The telephone
does not
receive caller
ID or the
telephone does
not show caller
ID during call
waiting.
Caller ID is a subscription
service. You must
subscribe to this service
from your telephone
service provider for this
feature to work on your
telephone.
Both your and the caller’s
telephone service
providers must use
equipment compatible
with the caller ID service.
The caller may not be
calling from an area which
supports caller ID.
The caller ID information
displays after the first or
second ring.
The display
shows Out of
range or no pwr
at base.
The handset may be out
of range. Move it closer to
the telephone base.
Make sure the power cord
is securely plugged into
the telephone base. Use
a working electrical outlet
not controlled by a wall
switch.
I cannot hear
any instruction
from the
handset when
I try to record,
play or delete
my own
announcement.
The handset does not
have a speakerphone.
When recording,
playing or deleting your
own announcement,
the instructions are
announced through the
handset receiver. Make
sure you place the handset
receiver close to your ear.
easy for you to drop off the spent battery
at local retailers participating in the RBRC®
program or at authorized VTech product
service centers. Please call
1-800-8-BATTERY® for information on
Ni-MH battery recycling and disposal
bans/restrictions in your area. VTech’s
involvement in this program is part
of its commitment to protecting our
environment and conserving natural
resources.
The RBRC seal and 1-800-8-BATTERY® are
registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and
found to comply with the requirements
for a Class B digital device under Part 15 of
the Federal Communications Commission
(FCC) rules. These requirements are
intended to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
22 23
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Changes or modifications to this
equipment not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation. Privacy of
communications may not be ensured when
using this telephone.
To ensure safety of users, the FCC has
established criteria for the amount of
radio frequency energy that can be safely
absorbed by a user or bystander according
to the intended usage of the product. This
product has been tested and found to
comply with the FCC criteria. The handset
may be safely held against the ear of the
user. The telephone base shall be installed
and used such that parts of the user’s body
other than the hands are maintained at a
distance of approximately 20 cm (8 inches)
or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
If this equipment is malfunctioning, it must
be unplugged from the modular jack
until the problem has been corrected.
Replacement to this telephone equipment
can only be made by the manufacturer
or its authorized agents. For replacement
procedures, follow the instructions
outlined under the Limited warranty.
If this equipment is causing harm to the
telephone network, the telephone service
provider may temporarily discontinue
your telephone service. The telephone
service provider is required to notify you
before interrupting service. If advance
notice is not practical, you will be notified
as soon as possible. You will be given
the opportunity to correct the problem
and the telephone service provider is
required to inform you of your right to file
a complaint with the FCC. Your telephone
service provider may make changes in
its facilities, equipment, operation, or
procedures that could affect the proper
functioning of this product. The telephone
service provider is required to notify you if
such changes are planned.
If this product is equipped with a corded
or cordless handset, it is hearing aid
compatible.
If this product has memory dialing
locations, you may choose to store
emergency telephone numbers (e.g.,
police, fire, medical) in these locations. If
you do store or test emergency numbers,
please:
Remain on the line and briefly explain the
reason for the call before hanging up.
Perform such activities in off-peak hours,
such as early morning or late evening.
Industry Canada
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
FCC Part 68 and ACTA
This equipment complies with Part 68
of the FCC rules and with technical
requirements adopted by the
Administrative Council for Terminal
Attachments (ACTA). The label on the back
or bottom of this equipment contains,
among other things, a product identifier
in the format US:AAAEQ##TXXXX. This
identifier must be provided to your
telephone service provider upon request.
The plug and jack used to connect this
equipment to premises wiring and the
telephone network must comply with
applicable Part 68 rules and technical
requirements adopted by ACTA. A
compliant telephone cord and modular
plug is provided with this product. It is
designed to be connected to a compatible
modular jack that is also compliant. An
RJ11 jack should normally be used for
connecting to a single line and an RJ14
jack for two lines. See the installation
instructions in the user’s manual.
The Ringer Equivalence Number (REN) is
used to determine how many devices you
may connect to your telephone line and
still have them ring when you are called.
The REN for this product is encoded as the
6th and 7th characters following the US: in
the product identifier (e.g., if ## is 03, the
REN is 0.3). In most, but not all areas, the
sum of all RENs should be five (5.0) or less.
For more information, please contact your
telephone service provider.
This equipment may not be used with
Party Lines. If you have specially wired
alarm dialing equipment connected to
your telephone line, ensure the connection
of this equipment does not disable your
alarm equipment. If you have questions
about what will disable alarm equipment,
consult your telephone service provider or
a qualified installer.
Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this telephone.
The term ‘’IC:‘’ before the certification/
registration number only signifies that the
Industry Canada technical specifications
were met.
The Ringer Equivalence Number (REN) for
this terminal equipment is 1.0. The REN
is an indication of the maximum number
of devices allowed to be connected to a
telephone interface. The termination on an
interface may consist of any combination
of devices subject only to the requirement
that the sum of the RENs of all the devices
does not exceed five.
This product meets the applicable
Innovation, Science and Economic
Development Canada technical
specifications.
California Energy Commission
battery charging testing
instructions
This telephone is set up to comply with the
energy-conserving standards right out of
the box. These instructions are intended for
California Energy Commission (CEC) compliance
testing only. When the CEC battery charging
testing mode is activated, all telephone
functions, except battery charging, will be
disabled.
To activate the CEC battery charging testing
mode:
1. Unplug the telephone base power
adapter from the power outlet. Make sure
24 25
all handsets are plugged with charged
batteries before proceeding.
2. While you press and hold /FIND
HANDSET, plug the telephone base
power adapter back to the power outlet.
3. After about 30 seconds, when the IN
USE light starts flashing, release /FIND
HANDSET and then press it again within 2
seconds.
NOTES
When the phone successfully enters the CEC
battery charging testing mode, all handsets
display To register HS and See manual
alternatively.
When the phone fails to enter this mode, repeat
Step 1 through Step 3 above.
To deactivate the CEC battery charging testing
mode:
1. Unplug the telephone base power adapter
from the power outlet, then plug it back in.
Then the telephone base is powered up as
normal.
2. Register your handsets back to the
telephone base. Refer to Register a
handset.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de
blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de
base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions et
mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise
murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en
aérosol. N’utilisez qu’un chiffon doux
et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau,
tel que près d’un bain, d’un lavabo,
d’un évier de cuisine, d’un bac de
lavage ou d’une piscine, ou dans un
d’électrocution. N’échappez pas de
liquides dans l’appareil.
11. Afin de réduire les risques
d’électrocution, ne démontez pas
l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il
doit être réparé. En enlevant le
couvercle, vous vous exposez à des
tensions dangereuses ou autres
dangers similaires. Un remontage
inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez
l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide
et doux.
12. Ne surchargez pas les prises de
courant et les rallonges.
13. Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service à la clientèle
de VTech dans les cas suivants :
Lorsque le cordon d’alimentation
est endommagé ou écorché.
Si du liquide a été échappé dans
l’appareil.
Si l’appareil a été exposé à une
source d’humidité telle que la pluie
ou l’eau.
Si le produit ne fonctionne pas
normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les commandes
indiquées dans le les instructions
de fonctionnement. Les réglages
incorrects des autres commandes
pourraient provoquer un
dommage qui pourrait exiger un
travail exhaustif de la part d’un
technicien autorisé afin de rétablir
le fonctionnement normal de
l’appareil.
Si le produit a été échappé et que
le socle et/ou le combiné a été
endommagé.
sous-sol humide ou sous la douche.
5. Ne déposez pas ce téléphone sur un
chariot, support ou table chancelants.
L’appareil pourrait tomber et être
sérieusement endommagé.
6. Évitez d’installer le système
téléphonique dans les endroits
soumis à une température extrême,
à la lumière directe du soleil ou à
proximité immédiate d’autres appareils
électriques ou électroniques. Protégez
votre téléphone contre les sources
d’humidité, la poussière, les vapeurs et
les liquides corrosifs.
7. Le boîtier de l’appareil est doté de
fentes et d’ouvertures d’aération
situées à l’arrière ou en dessous.
Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être
obstruées en plaçant l’appareil sur
un lit, divan, tapis ou autre surface
similaires. Ne placez pas cet appareil à
proximité d’un élément de chauffage
ni d’une plinthe électrique. De plus, ne
l’installez pas dans une unité murale ou
un cabinet fermé qui ne possède pas
d’aération adéquate.
8. Ne faites fonctionner cet appareil
qu’avec le type d’alimentation indiqué
sur les étiquettes de l’appareil. Si vous
ne connaissez pas le voltage de votre
maison, consultez votre marchand ou
votre fournisseur d’électricité.
9. Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil
dans un endroit sécuritaire, là où
personne ne pourra trébucher sur
la ligne d’alimentation ni le cordon
téléphonique modulaire.
10. N’insérez jamais d’objets à travers
les fentes et ouvertures de cet
appareil, car ils pourraient toucher
à des points de tension dangereux
ou court-circuiter des pièces, ce qui
constituerait un risque d’incendie ou
Si le produit affiche une nette
diminution de sa performance.
14. Évitez d’utiliser un téléphone (autre
qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une
électrocution.
15. N’utilisez pas le téléphone pour
rapporter une fuite de gaz à proximité
de la fuite. En certaines circonstances,
une flammèche pourrait être
provoquée lorsque l’adaptateur
est branché à une prise de courant,
ou lorsque le combiné est déposé
sur le socle. Ceci est un événement
commun associé à la fermeture d’un
circuit électrique. L’utilisateur ne
devrait pas brancher le téléphone à
une prise de courant, et ne devrait
pas déposer le combiné chargé sur
le socle, si le téléphone se trouve à
proximité d’un endroit comportant des
concentrations de gaz inflammables, à
moins que la ventilation soit adéquate.
Une flammèche dans un tel endroit
pourrait provoquer un incendie ou
une explosion. De tels environnements
peuvent comprendre: des endroits
où l’on utilise de l’oxygène médical
sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une fuite
de gaz naturel, etc.
16. Ne placez que le combiné de votre
téléphone près de votre oreille
lorsqu’en mode de conversation.
17. Ces adaptateurs ont été conçus pour
être orientés en position verticale ou
montés au sol. Les broches ne sont pas
conçues pour maintenir l’adaptateur en
place si celui-ci est barnché dans une
prise au plafond ou sous une table/
armoire.
CONSERVEZ CES INSTRUCTIONS
26 27
Pile
MISE EN GARDE : N’utilisez que la pile
incluse.
Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux
rebus auprès des autorités locales.
N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est
corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la peau.
L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez
les piles afin d’éviter les courts-
circuits provoqués par des matériaux
conducteurs.
Rechargez la pile incluse avec cet
appareil, selon les instructions et limites
spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés
dans l’organisme
Les simulateurs cardiaques (s’applique
uniquement aux téléphones numériques
sans fil) :
L’organisme ‘Wireless Technology
Research, LLC (WTR)’, une firme de
recherche indépendante, a mené
une évaluation pluridisciplinaire des
interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques
implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues
(FDA) des États-Unis, la firme WTR
recommande aux médecins :
Avis aux détenteurs de stimulateurs
cardiaques
Ils doivent tenir le téléphone sans fil à
une distance d’au moins six pouces du
stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone
sans fil directement sur le stimulateur
cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
présence de parasites, il est conseillé
d’éloigner le téléphone sans fil du
téléviseur ou du magnétoscope afin de
réduire possiblement les interférences.
Piles rechargeables : Manipulez les
piles avec soin afin de ne pas les court-
circuiter avec des bagues, bracelets ou
clés. Les piles ou le conducteur peut
surchauffer et causer des blessures.
Respectez la polarité adéquate entre la
pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure
métallique de nickel : Jetez ces
blocs-piles de manière écologique et
sécuritaire. Ne les incinérez pas et ne
les percez pas. Tel que les autres piles
de ce type, elles pourraient dégager
une matière toxique qui peut causer
des blessures corporelles si elles sont
brûlées ou percées.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech product,
VTech Communications, Inc. (“VTech”),
warrants to the holder of a valid proof of
purchase (“Consumer” or “you”) that the
Product and all accessories provided by
VTech in sales package (“Product”) are
free from material defects in material and
workmanship, pursuant to the following
terms and conditions, when installed
and used normally and in accordance
with operating instructions. This limited
warranty extends only to the Consumer
for Products purchased and used in the
United States of America and Canada.
What will VTech Communications do if the
Product is not free from material defects
in materials and workmanship during
the limited warranty period (“Materially
Defective Product”)?
During the limited warranty period,
Ils doivent utiliser le téléphone sans
fil en l’appuyant sur l’oreille qui se
trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a
pas identifié de risque pour les détenteurs
de simulateurs cardiaques causés par les
gens qui utilisent un téléphone sans fil à
proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes
caractéristiques qui constituent des
avantages pour les téléphones sans fil
affichent également des restrictions.
Les appels téléphoniques sont transmis
entre le combiné sans fil et le socle
par le biais d’ondes radio ; il y a donc
la possibilité que vos conversations
téléphoniques sans fil soient
interceptées par des équipements de
réception radio se trouvant dans la
portée du combiné sans fil. Pour cette
raison, vous ne devez pas percevoir les
communications téléphoniques sans fil
comme étant aussi confidentielles que
celles des téléphones à cordons.
Alimentation électrique : Le socle de
ce téléphone sans fil doit être branché
à une prise électrique fonctionnelle.
La prise électrique ne doit pas être
contrôlée par un interrupteur mural. Les
appels ne pourront pas être effectués
du combiné sans fil si le socle est
débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux
téléviseurs : Certains téléphones sans
fil fonctionnent sur des fréquences
pouvant causer des interférences aux
téléviseurs et aux magnétoscopes.
Pour réduire ou prévenir de telles
interférences, ne placez pas le socle
du téléphone sans fil près ou sur un
téléviseur ou magnétoscope. S’il y a
VTech’s authorized service representative
will replace at VTech’s option, without
charge, a Materially Defective Product.
If we choose to replace the Product, we
may replace it with a new or refurbished
Product of the same or similar design.
VTech will return replacement products to
you in working condition. VTech will retain
defective parts, modules, or equipment.
Replacement of the Product, at VTech’s
option, is your exclusive remedy. You
should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the
product extends for ONE (1) YEAR from
date of purchase (90 days on products
purchased as Refurbished*). This limited
warranty also applies to replacement
Products for a period of either (a) 90 days
from the date the replacement Product is
shipped to you or (b) the time remaining
on the original one-year limited warranty
(90-day limited warranty on products that
are purchased as Refurbished*), whichever
is longer.
*Refurbished products purchased from our
online store carry a 90-day replacement
warranty.
What is not covered by this limited
warranty?
This limited warranty does not cover:
1. Product that has been subjected
to misuse, accident, shipping or
other physical damage, improper
installation, abnormal operation or
handling, neglect, inundation, fire,
water or other liquid intrusion; or
2. Product that has been damaged due
to repair, alteration or modification
by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem
experienced is caused by signal
28 29
conditions, network reliability or cable
or antenna systems; or
4. Product to the extent that the problem
is caused by use with non-VTech
electrical accessories; or
5. Product whose warranty/quality
stickers, Product serial number plates
or electronic serial numbers have
been removed, altered or rendered
illegible; or
6. Product purchased, used, serviced, or
shipped for repair from outside the
United States, or used for commercial
or institutional purposes (including but
not limited to Products used for rental
purposes); or
7. Product returned without valid proof
of purchase (see 2 below); or
8. Charges for installation or set up,
adjustment of customer controls, and
installation or repair of systems outside
the unit.
How do you get warranty service?
To obtain warranty service in the United
States of America, please visit our website
at www.vtechphones.com or call 1 (800)
595-9511 for instructions regarding where
to return the Product. In Canada, go to
phones.vtechcanada.com or dial 1 (800)
267-7377.
NOTE: Before calling for service, please
review the user’s manual - a check of the
Product’s controls and features may save
you a service call.
Except as provided by applicable law,
you assume the risk of loss or damage
during transit and transportation and
are responsible for delivery or handling
charges incurred in the transport of
Product(s) to the service location. VTech
will return replaced product under this
limited warranty to you, transportation,
delivery or handling charges prepaid.
VTech assumes no risk for damage or loss
of the Product in transit.
What must you return with the Product to
get warranty service?
1. Return the entire original package
and contents including the Product to
the VTech service location along with
a description of the malfunction or
difficulty;
2. Include “valid proof of purchase”
(sales receipt) identifying the Product
purchased (Product model) and the
date of purchase or receipt; and
3. Provide your name, complete
and correct mailing address, and
telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech.
It supersedes all other written or oral
communications related to this product.
VTech provides no other warranties for
this product. The warranty exclusively
describes all of VTech’s responsibilities
regarding the product.
There are no other expressed
warranties. No one is authorized to make
modifications to this warranty and you
should not rely on any such modification.
State Law Rights: This warranty gives you
specific legal rights, and you may also have
other rights which vary from state to state.
Limitations: Implied warranties, including
those of fitness for a particular purpose
and merchantability (an unwritten warranty
that the product is fit for ordinary use) are
limited to one year from date of purchase.
Some states do not allow limitations on
how long an implied warranty lasts, so the
above limitation may not apply to you.
In no event shall VTech be liable for any
indirect, special, incidental, consequential,
or similar damages (including, but not
limited to lost profits or revenue, inability
to use the product, or other associated
equipment, the cost of substitute
equipment, and claims by third parties)
resulting from the use of this product.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales
receipt as proof of purchase.
Disclaimer and Limitation of
Liability
VTech Communications, Inc. and its
suppliers assume no responsibility for any
damage or loss resulting from the use of
this user’s manual. VTech Communications,
Inc. and its suppliers assume no
responsibility for any loss or claims by third
parties that may arise through the use of
this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square
Road - Ste 555 Tigard, OR 97223, United
States
Phone: 1 (800) 595-9511 in the U.S. or
1 (800) 267-7377 in Canada
Technical specifications
Frequency
control Crystal controlled PLL synthesizer
Transmit
frequency 1921.536-1928.448 MHz
Channels 5
Nominal
effective
range
Maximum power allowed by
FCC and IC. Actual operating
range may vary according to
environmental conditions at the
time of use.
Power
requirements Handset: 2.4V Ni-MH battery
Telephone base:
6V DC @ 400mA
Charger: 6V DC @ 400mA
Memory Directory:
30 memory locations;
up to 30 digits and
15 characters
Caller ID log:
30 memory locations;
up to 24 digits and
15 characters
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 07/21. CS6114-X_WEBCIB_V14.0
Designed to fit your home.
And your life.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

VTech CS6114 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues