VTech CS6114 Manuel utilisateur

Marque: VTech

Modèle: CS6114

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

User’s manual

CS6114

CS6114-11

CS6114-2

DECT 6.0 cordless telephone

Go to www.vtechphones.com

to register your product for enhanced

warranty support and the latest VTech

product news.

For more support information

Congratulations

on purchasing your new VTech product.

Before using this telephone, please read

Important safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install

and operate your new VTech telephone.

Please review this manual thoroughly to

ensure proper installation and operation

of this innovative and feature rich VTech

product.

For support, shopping, and everything

new at VTech, visit our website at

www.vtechphones.com. In Canada, please

visit phones.vtechcanada.com/.

Compatible with

Hearing Aid T-Coil

TIA-1083

Telephones identiﬁed with

this logo have reduced noise

and interference when used

with most T-coil equipped

hearing aids and cochlear

implants. The TIA-1083

Compliant Logo is a trademark

of the Telecommunications

Industry Association. Used

under license.

Important safety instructions

When using your telephone equipment,

basic safety precautions should always be

followed to reduce the risk of ﬁre, electric

shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions

marked on the product.

3. Unplug this product from the wall

outlet before cleaning. Do not use

liquid or aerosol cleaners. Use a damp

cloth for cleaning.

4. Do not use this product near water

such as near a bath tub, wash

bowl, kitchen sink, laundry tub or a

swimming pool, or in a wet basement

or shower.

5. Do not place this product on an

unstable table, shelf, stand or other

unstable surfaces.

6. Avoid placing the telephone system

in places with extreme temperature,

direct sunlight, or other electrical

devices. Protect your phone from

moisture, dust, corrosive liquids and

fumes.

7. Slots and openings in the back or

bottom of the telephone base and

handset are provided for ventilation.

To protect them from overheating,

these openings must not be blocked

by placing the product on a soft

surface such as a bed, sofa or rug. This

product should never be placed near

or over a radiator or heat register. This

product should not be placed in any

area where proper ventilation is not

provided.

8. This product should be operated

only from the type of power source

indicated on the marking label. If you

are not sure of the type of power

supply in your home or ofﬁce, consult

your dealer or local power company.

9. Do not allow anything to rest on the

power cord. Do not install this product

where the cord may be walked on.

10. Never push objects of any kind into

this product through the slots in the

telephone base or handset because

they may touch dangerous voltage

points or create a short circuit. Never

spill liquid of any kind on the product.

11. To reduce the risk of electric shock,

do not disassemble this product, but

take it to an authorized service facility.

Opening or removing parts of the

telephone base or handset other than

speciﬁed access doors may expose

you to dangerous voltages or other

risks. Incorrect reassembling can cause

electric shock when the product is

subsequently used.

12. Do not overload wall outlets and

extension cords.

13. Unplug this product from the wall

outlet and refer servicing to an

authorized service facility under the

following conditions:

• When the power supply cord or

plug is damaged or frayed.

• If liquid has been spilled onto the

product.

• If the product has been exposed to

rain or water.

• If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operation instructions. Improper

adjustment of other controls may

result in damage and often requires

extensive work by an authorized

technician to restore the product to

normal operation.

• If the product has been dropped

and the telephone base and/or

handset has been damaged.

• If the product exhibits a distinct

change in performance.

14. Avoid using a telephone (other than

cordless) during an electrical storm.

There is a remote risk of electric shock

from lightning.

15. Do not use the telephone to report

a gas leak in the vicinity of the leak.

Under certain circumstances, a spark

may be created when the adapter

is plugged into the power outlet,

or when the handset is replaced in

its cradle. This is a common event

associated with the closing of any

electrical circuit. The user should

not plug the phone into a power

outlet, and should not put a charged

handset into the cradle, if the phone is

located in an environment containing

concentrations of ﬂammable or

ﬂame-supporting gases, unless there

is adequate ventilation. A spark in

such an environment could create a

ﬁre or explosion. Such environments

might include: medical use of oxygen

without adequate ventilation; industrial

gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your

telephone next to your ear when it is in

normal talk mode.

17. The power adapter is intended to be

correctly oriented in a vertical or ﬂoor

mount position. The prongs are not

designed to hold the plug in place if

it is plugged into a ceiling, under-the-

table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre.

Check with local waste management

The ENERGY STAR

program

(www.energystar.gov)

recognizes and encourages

the use of products that save

energy and help protect our

environment. We are proud

to mark this product with the

ENERGY STAR® label indicating

it meets the latest energy

efﬁciency guidelines.

codes for special disposal instructions.

• Do not open or mutilate the battery.

Released electrolyte is corrosive and

may cause burns or injury to the eyes

or skin. The electrolyte may be toxic if

swallowed.

• Exercise care in handling batteries in

order not to create a short circuit with

conductive materials.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in

this manual.

Precautions for users of implanted

cardiac pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC

(WTR), an independent research entity,

led a multidisciplinary evaluation of the

interference between portable wireless

telephones and implanted cardiac

pacemakers. Supported by the U.S.

Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least

six inches from the pacemaker.

• Should NOT place wireless telephones

directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

• Should use the wireless telephone at the

ear opposite the pacemaker.

WTR’s evaluation did not identify any risk

to bystanders with pacemakers from other

persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a

cordless telephone convenient create

some limitations. Telephone calls are

transmitted between the telephone

base and the cordless handset by radio

waves, so there is a possibility that

the cordless telephone conversations

could be intercepted by radio receiving

equipment within range of the

cordless handset. For this reason, you

should not think of cordless telephone

conversations as being as private as

those on corded telephones.

• Electrical power: The telephone base

of this cordless telephone must be

connected to a working electrical outlet.

The electrical outlet should not be

controlled by a wall switch. Calls cannot

be made from the cordless handset

if the telephone base is unplugged,

switched off or if the electrical power is

interrupted.

• Potential TV interference: Some

cordless telephones operate at

frequencies that may cause interference

to televisions and VCRs. To minimize or

prevent such interference, do not place

the telephone base of the cordless

telephone near or on top of a TV or

VCR. If interference is experienced,

moving the cordless telephone farther

away from the TV or VCR often reduces

or eliminates the interference.

• Rechargeable batteries: Exercise care in

handling batteries in order not to create

a short circuit with conducting material

such as rings, bracelets and keys. The

battery or conductor may overheat and

cause harm. Observe proper polarity

between the battery and the battery

charger.

• Nickel-metal hydride rechargeable

batteries: Dispose of these batteries in

a safe manner. Do not burn or puncture

the battery. Like other batteries of this

type, if burned or punctured, they

could release caustic material which

could cause injury.

Table of contents

Important safety instructions ................... II

What’s in the box .......................................1

Overview.....................................................2

Handset overview ........................................ 2

Telephone base overview ........................... 3

Charger overview ........................................ 3

Display icons overview ................................ 3

Connect ......................................................3

Connect the telephone base ....................... 3

Connect the charger .................................... 4

Mount the telephone base........................... 4

Install and charge the battery ...................... 4

Before use .................................................. 5

Set date and time ........................................ 5

Check for dial tone ...................................... 5

Congure your telephone .........................6

Use the handset menu ................................ 6

Set language ............................................... 6

Set date and time ........................................ 6

Operating range .......................................... 6

Dial mode .................................................... 7

Temporary tone dialing ................................ 7

Telephone operations ...............................8

Make a call .................................................. 8

Predial a call ................................................ 8

Answer a call ............................................... 8

End a call: .................................................... 8

Volume ........................................................ 8

Mute ............................................................ 8

Call waiting .................................................. 9

Chain dialing ................................................ 9

Find handset.............................................. 10

Redial list..................................................10

Review a redial list entry ........................... 10

Dial a redial list entry ................................. 10

Delete a redial list entry ............................. 10

Directory ...................................................10

Add a directory entry ..................................11

Review a directory entry .............................11

Alphabetical search ....................................11

Delete a directory entry ..............................11

Edit a directory entry ................................. 12

Dial a directory entry ................................. 12

Caller ID .................................................... 12

Review a caller ID log entry ...................... 13

Memory match........................................... 13

Missed call indicator .................................. 13

View dialing options................................... 13

Dial a caller ID log entry ............................ 13

Save a caller ID log entry to the directory . 14

Delete the caller ID log entries .................. 14

Sound settings .........................................14

Key tone .................................................... 14

Ringer tone ................................................ 14

Ringer volume ........................................... 15

Temporary ringer silencing ........................ 15

Retrieve voicemail from telephone service

Retrieve voicemail ..................................... 15

Turn off the new voicemail indicators ........ 16

Screen messages ....................................16

General product care ..............................18

Frequently asked questions ................... 18

The RBRC® seal .......................................21

FCC, ACTA and IC regulations ...............21

California Energy Commission battery

charging testing instructions ............23

For C-UL compliance only ...................... 24

Mesures de sécurité importantes .............. 24

Limited warranty ......................................27

Disclaimer and Limitation of Liability ....29

Technical specications ......................... 29

What’s in the box

Your telephone package contains the

following items. Save your sales receipt

and original packaging in the event

warranty service is necessary.

NOTE

• To purchase a replacement battery or power

adapter, visit our website at

www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com/ or call

1 (800) 267-7377.

1 set for CS6114/CS6114-11;

2 sets for CS6114-2

1 set for CS6114/CS6114-11/

CS6114-2

1 set for CS6114/CS6114-11/

CS6114-2

1 set for CS6114-2

Abridged

user’s

manual

Important

safety

instructions

2 3

Overview

Handset overview

1 – Handset earpiece

2 – LCD display

3 – CID/VOL-

• Review the caller ID log when the

telephone is not in use.

• Scroll down while in a menu, or in the

directory, caller ID log or redial list.

• Move the cursor to the left when

entering numbers or names.

• Decrease the listening volume during a

call.

4 – /FLASH

• Make or answer a call.

• Answer an incoming call when you

receive a call waiting alert.

5 – 1

• Press repeatedly to add or remove 1 in

front of the caller ID log entry before

dialing or saving it to the directory.

6 – TONE

• Switch to tone dialing temporarily

during a call.

7 – MUTE/DELETE

• Mute the microphone during a call.

Telephone base overview

1 – /FIND HANDSET

• Page all system handsets.

2 – Charging pole

Charger overview

1 – Charging pole

Display icons overview

The battery icon ﬂashes when

the battery is low and needs

charging.

The battery icon animates

when the battery is charging.

The battery icon becomes

solid when the battery is fully

charged.

There are new voicemail

received from your telephone

service provider.

NEW There are new caller ID log

entries.

Connect

You can choose to connect the telephone

base for desktop usage or wall mounting.

NOTES

• Use only the adapters provided.

• Make sure the electrical outlets are not

controlled by wall switches.

• The adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position.

The prongs are not designed to hold the

plug in place if it is plugged into a ceiling,

under-the-table or cabinet outlet.

TIP

• If you subscribe to digital subscriber line

(DSL) high-speed Internet service through

your telephone line, make sure you install

a DSL ﬁlter (not included) between the

telephone line cord and telephone wall jack.

Contact your DSL service provider for more

information.

Connect the telephone base

• Silence the handset ringer temporarily

while the phone is ringing.

• Delete the displayed entry while

reviewing the directory, caller ID log or

redial list.

• Delete digits or characters when

entering numbers or names.

8 – Microphone

9 – Charging pole

10 – MENU/SELECT

• Show the menu.

• While in a menu, press to select an item,

or save an entry or setting.

11 – /VOL+

• Review the directory when the phone is

not in use.

• Scroll up while in a menu, or in the

directory, caller ID log or redial list.

• Move the cursor to the right when

entering numbers or names.

• Increase the listening volume during a

call.

12 – OFF/CANCEL

• Hang up a call.

• Return to the previous menu or idle

mode without making changes.

• Delete digits while predialing.

• Silence the handset ringer temporarily

while the phone is ringing.

• Erase the missed call indicator while the

handset is not in use.

13 – 0/OPER

• Enter space character during text

editing.

14 – #

• Show other dialing options when

reviewing a caller ID log entry.

15 – REDIAL/PAUSE

• Review the redial list.

• Insert a dialing pause while dialing or

entering numbers into the directory.

16 – Battery compartment cover

4 5

Charge the battery

Place the handset in the telephone

base or the charger to charge.

Once you have installed the battery, the

handset LCD display indicates the battery

status (see the following table).

NOTES

• For best performance, keep the handset in

the telephone base or charger when not in

use.

• The battery is fully charged after 16 hours of

continuous charging.

• If you place the handset in the telephone

base or the charger without plugging in the

battery, the screen displays No battery.

Connect the charger

Mount the telephone base

Install and charge the battery

Install the battery

Install the battery as shown below.

NOTES

• Use only supplied battery.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in this

manual.

• If the handset will not be used for a long

time, disconnect and remove the battery to

prevent possible leakage.

Battery

indicators Battery

status Action

The screen

is blank, or

displays Put in

charger and

ﬂashes.

The battery

has no or

very little

charge. The

handset

cannot be

used.

Charge

without

interruption

(at least 30

minutes).

The screen

displays

Low battery

and ﬂashes.

The battery

has enough

charge to be

used for a

short time.

Charge

without

interruption

(about 30

minutes).

The screen

displays

HANDSET X.

The battery

is charged. To keep

the battery

charged,

place it in the

telephone

base or

charger when

not in use.

When the battery is fully charged, you can

expect the following performance:

Operation Operating

time

While in use (talking*) Seven hours

While not in use (standby**) Five days

* Operating times vary depending on your

actual use and the age of the battery.

** Handset is not charging nor in use.

Before use

After you install your telephone or power

returns following a power outage, the

handset will prompt you to set the date

and time.

Set date and time

1. Use the dialing keys (0-9) to enter the

month (MM), date (DD) and year (YY).

Then press SELECT.

2. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press q or p to choose AM or PM.

3. Press SELECT to save.

Check for dial tone

Press . If you hear a dial tone, the

installation is successful.

If you do not hear a dial tone:

• Make sure the installation procedures

described above are properly done.

• It may be a wiring problem. If you have

changed your telephone service to

digital service from a cable company or

a VoIP service provider, the telephone

line may need to be rewired to allow

all existing telephone jacks to work.

Contact your cable/VoIP service

provider for more information.

THIS SIDE UP

6 7

Dial mode

The dial mode is preset to touch-tone

dialing. If you have pulse (rotary) service,

you need to change the dial mode to

pulse dialing before using the telephone.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings, and

then press SELECT.

3. Press q or p to choose Dial mode,

then press SELECT.

4. Press or to choose Touch-tone or

Pulse, then press SELECT to conﬁrm

your selection. You hear a conﬁrmation

tone.

Temporary tone dialing

If you have pulse (rotary) service only,

you can switch from pulse to touch-tone

dialing temporarily during a call. This is

useful if you need to send touch-tone

signals to access your telephone banking

or long distance services.

1. During a call, press TONE .

2. Use the dialing keys to enter the

number. The telephone sends touch-

tone signals. It automatically returns to

pulse dialing mode after you end the

call.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance

- which can vary with the locations of the

telephone base and handset, the weather,

and the layout of your home or ofﬁce.

When the handset is out of range, the

handset displays Out of range or no pwr

at base.

If there is a call while the handset is out of

range, it may not ring, or if it does ring, the

call may not connect well when you press

. Move closer to the telephone base,

then press to answer the call.

If the handset moves out of range during

a telephone conversation, there may be

interference. To improve reception, move

closer to the telephone base.

Conﬁgure your telephone

Use the handset menu

1. Press MENU when the phone is not in

use.

2. Press or until the screen displays

the desired feature menu.

3. Press SELECT.

• To return to the previous menu, press

CANCEL.

• To return to idle mode, press and hold

CANCEL.

Set language

The LCD language is preset to English. You

can select English, French or Spanish to be

used in all screen displays.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings and

then press SELECT twice.

3. Press q or p to choose English,

Français or Español.

4. Press SELECT twice to save your

setting. You hear a conﬁrmation tone.

Set date and time

1. Press MENU on the handset when not

in use.

2. Press q or p to choose Set

date/time and then press SELECT.

3. Use the dialing keys (0-9) to enter the

month (MM), date (DD) and year (YY).

Then press SELECT.

4. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press q or p to choose AM or PM.

5. Press SELECT to save your setting. Your

hear a conﬁrmation tone.

8 9

Telephone operations Call waiting

When you subscribe to call waiting service

from your telephone service provider, you

hear an alert tone if there is an incoming

call while you are already on a call.

• Press FLASH to put the current call on

hold and take the new call.

• Press FLASH at any time to switch back

and forth between calls.

If you also subscribe to caller ID service, it

will let you see the name and telephone

number of the caller during call waiting.

It may be necessary to change your

telephone service to use this feature.

Contact your telephone service provide if:

• You have both caller ID and call waiting,

but as separate service (you may need

to combine these service);

• You have only caller ID service, or only

call waiting service; or

• You do not subscribe to caller ID or call

waiting services.

There are fees for caller ID services. In

addition, services may not be available in

all areas.

Chain dialing

Use this feature to initiate a dialing

sequence from numbers stored in the

directory, caller ID log or redial while you

are on a call.

Chain dialing can be useful if you wish

to access other numbers (such as bank

account numbers or access codes) from

the directory, caller ID log or redial list.

To access a number in the directory

while on a call:

1. Press MENU/SELECT twice to enter the

directory.

2. Press q or p to scroll to the desired

entry.

3. Press SELECT to dial the displayed

Handset control key panel:

CANCEL

Make a call

• Press , and then dial the telephone

number.

NOTES

• The screen shows the elapsed time as you

talk (in hours, minutes and seconds).

• If the handset is moved out of range while

on a call, it will beep three times.

Predial a call

• Enter the telephone number using

the dialing keys (0-9), then press to

dial.

NOTE

• When predialing (preview numbers

before dialing), press DELETE or CANCEL

to backspace and delete; press and hold

PAUSE to insert a dialing pause (a P appears).

Answer a call

• Press or any of the dialing keys.

End a call:

• Press OFF or put the handset back in the

telephone base or charger.

Volume

• During a call, press VOL- or VOL+ to

adjust the listening volume.

Mute

The mute function allows you to hear the

other party but the other party cannot hear

you.

1. During a call, press MUTE. The handset

displays Muted.

2. Press MUTE again to resume the

conversation. The handset displays

Microphone on brieﬂy.

number.

To access a number in the caller ID log

while on a call:

1. Press MENU and then press q or p to

select Caller ID log.

2. Press SELECT and then press q or p

to scroll to the desired entry.

3. Press SELECT to dial the displayed

number.

To access a number in the redial list

while on a call:

1. Press REDIAL.

2. Press q, p or REDIAL repeatedly to

browse to the desired entry.

3. Press SELECT to dial the displayed

number.

NOTES

• You cannot edit a directory entry while on a

call. Refer to the Directory section for more

details.

• You cannot copy a caller ID log entry into the

directory while on a call. Refer to the Caller

ID log section for more details.

• You cannot erase a redial entry while on a

call. Refer to the Redial list section for more

details.

• Press CANCEL to exit redial, directory or

caller ID log when you are on a call.

10 11

Find handset

Use this feature to ﬁnd the system handset.

To start paging:

• Press /FIND HANDSET on the

telephone base when not in use.

All idle handsets ring and display

** Paging **.

To end paging:

• Press /FIND HANDSET at the

telephone base.

-OR-

• Press or any of the dialing keys on

the handset.

NOTES

• Press MUTE to turn off the ringer of a

handset temporarily. Paging tone continues

on the other handset.

• Do not press and hold /FIND HANDSET

for more than four seconds. It may lead

to handset deregistration. If the handset

displays To register HS and See manual,

refer to the Register a handset section to

base.

Redial list

Each handset stores the last ﬁve telephone

numbers dialed. Entries are shown in

reverse chronological order. When there

are already ﬁve entries, the oldest entry is

deleted to make room for the new entry.

Review a redial list entry

1. Press REDIAL when the handset is not

in use.

2. Press q, p or REDIAL repeatedly until

the desired entry displays.

Add a directory entry

1. Enter the number when the phone is

not in use. Press MENU, then go to

Step 3.

-OR-

Press MENU when the phone is not

in use, then press SELECT to choose

Directory. Press SELECT again to

choose Add contact.

2. When Enter number

displays, use the

dialing keys to enter

the number.

-OR-

Copy a number from the redial list

by pressing REDIAL and then press

q, p or REDIAL repeatedly to select

a number. Press SELECT to copy the

number.

3. Press SELECT to move

on to enter the name.

The handset displays

Enter name.

4. Use the dialing keys to enter the

name. Additional key presses show

other characters of that particular key.

The ﬁrst character of every word is

capitalized.

5. Press SELECT to save. The handset

displays Saved and then you hear a

conﬁrmation tone.

While entering names and numbers, you

can:

• Press DELETE to backspace and erase a

digit or character.

• Press and hold DELETE to erase the

entire entry.

• Press q or p to move the cursor to the

left or right.

• Press and hold PAUSE to insert a dialing

pause (for entering numbers only).

• Press 0 to add a space (for entering

names only).

Dial a redial list entry

1. Press REDIAL when the handset is not

in use.

2. Press q, p or REDIAL repeatedly until

the desired entry displays.

3. Press to dial.

-OR-

1. Press when the handset is not in

use.

2. Press REDIAL and then press q, p or

REDIAL repeatedly until the desired

entry displays.

3. Press SELECT to dial.

Delete a redial list entry

1. Press REDIAL when the handset is not

in use.

2. Press q, p or REDIAL repeatedly to

browse to the desired entry.

3. Press DELETE to delete the displayed

number. You hear a conﬁrmation tone.

Directory

full

The directory is full.

Ended

X:XX:XX

You have just ended a

call.

Incoming

call

There is an incoming call.

Line in

use

A system handset is in use,

or another telephone on

the same line is in use.

LONG

DISTANCE

or L (before the

caller’s number)

It is a long distance call.

Low

battery

The battery needs to be

recharged.

Microphone

MUTE is turned off and

the person on the other

end can hear you.

Muted You have turned off the

handset microphone. The

other party cannot hear

you but you can hear the

other party.

New

voicemail

There are new voicemail

message(s) from the

telephone service

provider.

No battery No battery is installed.

Follow the directions

for battery installation

on page 4 to install the

battery before charging.

No line There is no telephone line

connected.

Clr voicemail

18 19

PRIVATE

CALLER

The caller is blocking the

name and the telephone

number information.

Put in

charger

The battery is very low.

Place the handset in

the telephone base or

charger for recharging.

Ringer

muted

The handset ringer is

muted temporarily during

an incoming call.

Ringer off The handset ringer is

turned off.

Saved Your selection has been

saved.

Unable to

call.

Failed phone call (the

other handset is in use).

UNKNOWN

NAME

This caller’s name is

unavailable.

UNKNOWN

NUMBER

This caller’s number is

unavailable.

UNKNOWN

CALLER

No caller information is

available about this caller.

XX missed

calls

There are calls that have

not been reviewed in the

caller ID log.

** Paging

The system handsets are

being paged.

General product care

Taking care of your telephone

Your cordless telephone contains

sophisticated electronic parts, so it must be

treated with care.

Avoid rough treatment

Place the handset down gently. Save the

original packing materials to protect your

telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets

wet. Do not use the handset outdoors in

the rain, or handle it with wet hands. Do

not install the telephone base near a sink,

The display

shows No line. I

cannot hear the

dial tone.

Disconnect the telephone

line cord from your

telephone and connect

it to another telephone.

If there is no dial tone

on that other telephone

either, then the telephone

line cord may be

defective. Try installing a

new telephone line cord.

If changing the telephone

line cord does not help,

the wall jack (or the wiring

to this wall jack) may

be defective. Contact

your telephone service

provider.

You may be using a new

cable or VoIP service, the

existing telephone jacks in

your home may no longer

work. Contact your service

provider for solutions.

I cannot dial out. Make sure there is a dial

tone before dialing. It

is normal if the handset

takes a second or two

to synchronize with the

telephone base before

producing a dial tone.

Wait an extra second

before dialing.

Eliminate any background

noise. Mute the handset

before dialing, or dial

from another room in

your home with less

background noise.

bathtub or shower.

Electrical storms

Electrical storms can sometimes cause

power surges harmful to electronic

equipment. For your own safety, take

caution when using electrical appliances

during storms.

Cleaning your telephone

Your telephone has a durable plastic casing

that should retain its luster for many years.

Clean it only with a dry non-abrasive cloth.

Do not use dampened cloth or cleaning

solvents of any kind.

Frequently asked questions

Below are the questions most frequently

asked about the cordless telephone. If you

cannot ﬁnd the answer to your question,

visit our website at

www.vtechphones.com or call

1 (800) 595-9511 for customer service.

My telephone

does not work

at all.

Make sure the telephone

base is installed properly,

and battery is installed

and charged correctly.

For optimum daily

performance, return the

handset to the telephone

base after use.

The display

shows To

See manual

alternately. The

handset does

not work at all.

The handset is

deregistered from the

telephone base. Follow

the steps in Register a

handset to register the

handset back to the

telephone base.

The display

shows Low

battery.

Place the handset in the

telephone base or charger

for charging.

The battery

does not charge

in the handset

or the handset

battery does not

accept charge.

Make sure the handset is

placed in the telephone

base or charger correctly.

If the battery is completely

depleted, charge the

battery for at least

30 minutes before use.

You may need to purchase

a new battery.

The telephone

does not ring

when there is an

incoming call.

Make sure the ringer

volume is not set to off.

The handset may be too

far from the telephone

base. Move it closer to the

telephone base.

My handset

beeps and is

not performing

normally.

Move the handset closer

to the telephone base. It

may be out of range.

I hear noise on

the cordless

handset and

the keys do not

work.

Make sure the telephone

line cord is plugged in

securely.

I hear other calls

when using the

telephone.

Disconnect the telephone

base from the telephone

wall jack. Plug in a

different telephone. If you

still hear other calls, the

problem is probably in

the wiring or telephone

service. Contact your

telephone service

provider.

20 21

There is

interference

during a

telephone

conversation.

My calls fade

out when

I am using

the cordless

handset.

The handset may be out

of range. Move it closer to

the telephone base.

If you subscribe to high-

speed Internet service

(DSL - digital subscriber

line) through your

telephone line, you must

install a DSL ﬁlter between

the telephone line cord

and the telephone wall

jack. The ﬁlter prevents

noise and caller ID

problems caused by DSL

interference. Contact your

DSL service provider for

more information about

DSL ﬁlters.

Appliances or other

cordless telephones

plugged into the

same circuit as the

telephone base can

cause interference. Try

moving the appliance or

telephone base to another

outlet.

The location of your

telephone base can

impact the performance

of your cordless phone.

For better reception,

install the telephone base

in a centralized location

within your home or

ofﬁce, away from walls

or other obstructions.

In many environments,

elevating the telephone

base improves overall

performance.

I subscribe to a

nontraditional

telephone

service that uses

my computer

to establish

connections,

and my

telephone

doesn’t work.

Make sure your computer

is powered on, and

your Internet is working

properly.

Make sure to plug your

USB telephone adapter

into a dedicated USB port

on your computer. Do not

plug into a multiple port

USB hub (USB splitter) that

is not powered.

In a few rare instances,

the USB port on your

computer may not have

enough power. In these

instances, try using a USB

hub with its own external

power supply.

If you are using a ﬁrewall,

it may prevent access

to your nontraditional

telephone service. Contact

your service provider for

more information.

I accidentally

set my LCD

language to

Spanish or

French, and I

don’t know how

to change it

back to English.

While the handset is not in

use, press MENU and then

enter 364# to change

the handset LCD language

back to English.

The RBRC® seal

The RBRC® seal on the nickel-metal

hydride battery indicates that VTech

Communications, Inc. is voluntarily

participating in an industry program to

collect and recycle these batteries at the

end of their useful lives, when taken out

of service within the United States and

Canada.

The RBRC® program provides a convenient

alternative to placing used nickel-

metal hydride batteries into the trash or

municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it

The telephone

does not

receive caller

ID or the

telephone does

not show caller

ID during call

waiting.

Caller ID is a subscription

service. You must

subscribe to this service

from your telephone

service provider for this

feature to work on your

telephone.

Both your and the caller’s

telephone service

providers must use

equipment compatible

with the caller ID service.

The caller may not be

calling from an area which

supports caller ID.

The caller ID information

displays after the ﬁrst or

second ring.

The display

shows Out of

range or no pwr

at base.

The handset may be out

of range. Move it closer to

the telephone base.

Make sure the power cord

is securely plugged into

the telephone base. Use

a working electrical outlet

not controlled by a wall

switch.

I cannot hear

any instruction

from the

handset when

I try to record,

play or delete

my own

announcement.

The handset does not

have a speakerphone.

When recording,

playing or deleting your

own announcement,

the instructions are

announced through the

handset receiver. Make

sure you place the handset

receiver close to your ear.

easy for you to drop off the spent battery

at local retailers participating in the RBRC®

program or at authorized VTech product

service centers. Please call

1-800-8-BATTERY® for information on

Ni-MH battery recycling and disposal

bans/restrictions in your area. VTech’s

involvement in this program is part

of its commitment to protecting our

environment and conserving natural

resources.

The RBRC seal and 1-800-8-BATTERY® are

registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and

found to comply with the requirements

for a Class B digital device under Part 15 of

the Federal Communications Commission

(FCC) rules. These requirements are

intended to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates,

uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio

or television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

22 23

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Changes or modiﬁcations to this

equipment not expressly approved by the

party responsible for compliance could

void the user’s authority to operate the

equipment.

This device complies with Part 15 of the

FCC rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation. Privacy of

communications may not be ensured when

using this telephone.

To ensure safety of users, the FCC has

established criteria for the amount of

radio frequency energy that can be safely

absorbed by a user or bystander according

to the intended usage of the product. This

product has been tested and found to

comply with the FCC criteria. The handset

may be safely held against the ear of the

user. The telephone base shall be installed

and used such that parts of the user’s body

other than the hands are maintained at a

distance of approximately 20 cm (8 inches)

or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

If this equipment is malfunctioning, it must

be unplugged from the modular jack

until the problem has been corrected.

Replacement to this telephone equipment

can only be made by the manufacturer

or its authorized agents. For replacement

procedures, follow the instructions

outlined under the Limited warranty.

If this equipment is causing harm to the

telephone network, the telephone service

provider may temporarily discontinue

your telephone service. The telephone

service provider is required to notify you

before interrupting service. If advance

notice is not practical, you will be notiﬁed

as soon as possible. You will be given

the opportunity to correct the problem

and the telephone service provider is

required to inform you of your right to ﬁle

a complaint with the FCC. Your telephone

service provider may make changes in

its facilities, equipment, operation, or

procedures that could affect the proper

functioning of this product. The telephone

service provider is required to notify you if

such changes are planned.

If this product is equipped with a corded

or cordless handset, it is hearing aid

compatible.

If this product has memory dialing

locations, you may choose to store

emergency telephone numbers (e.g.,

police, ﬁre, medical) in these locations. If

you do store or test emergency numbers,

please:

Remain on the line and brieﬂy explain the

reason for the call before hanging up.

Perform such activities in off-peak hours,

such as early morning or late evening.

Industry Canada

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

FCC Part 68 and ACTA

This equipment complies with Part 68

of the FCC rules and with technical

requirements adopted by the

Administrative Council for Terminal

Attachments (ACTA). The label on the back

or bottom of this equipment contains,

among other things, a product identiﬁer

in the format US:AAAEQ##TXXXX. This

identiﬁer must be provided to your

telephone service provider upon request.

The plug and jack used to connect this

equipment to premises wiring and the

telephone network must comply with

applicable Part 68 rules and technical

requirements adopted by ACTA. A

compliant telephone cord and modular

plug is provided with this product. It is

designed to be connected to a compatible

modular jack that is also compliant. An

RJ11 jack should normally be used for

connecting to a single line and an RJ14

jack for two lines. See the installation

instructions in the user’s manual.

The Ringer Equivalence Number (REN) is

used to determine how many devices you

may connect to your telephone line and

still have them ring when you are called.

The REN for this product is encoded as the

6th and 7th characters following the US: in

the product identiﬁer (e.g., if ## is 03, the

REN is 0.3). In most, but not all areas, the

sum of all RENs should be ﬁve (5.0) or less.

For more information, please contact your

telephone service provider.

This equipment may not be used with

Party Lines. If you have specially wired

alarm dialing equipment connected to

your telephone line, ensure the connection

of this equipment does not disable your

alarm equipment. If you have questions

about what will disable alarm equipment,

consult your telephone service provider or

a qualiﬁed installer.

Development Canada’s licence-exempt

RSS(s).

Operation is subject to the following

two conditions: (1) this device may not

cause interference, and (2) this device

must accept any interference, including

interference that may cause undesired

operation.

Privacy of communications may not be

ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/

registration number only signiﬁes that the

Industry Canada technical speciﬁcations

were met.

The Ringer Equivalence Number (REN) for

this terminal equipment is 1.0. The REN

is an indication of the maximum number

of devices allowed to be connected to a

telephone interface. The termination on an

interface may consist of any combination

of devices subject only to the requirement

that the sum of the RENs of all the devices

does not exceed ﬁve.

This product meets the applicable

Innovation, Science and Economic

Development Canada technical

speciﬁcations.

California Energy Commission

battery charging testing

instructions

This telephone is set up to comply with the

energy-conserving standards right out of

the box. These instructions are intended for

California Energy Commission (CEC) compliance

testing only. When the CEC battery charging

testing mode is activated, all telephone

functions, except battery charging, will be

disabled.

To activate the CEC battery charging testing

mode:

1. Unplug the telephone base power

adapter from the power outlet. Make sure

24 25

all handsets are plugged with charged

batteries before proceeding.

2. While you press and hold /FIND

HANDSET, plug the telephone base

power adapter back to the power outlet.

3. After about 30 seconds, when the IN

USE light starts ﬂashing, release /FIND

HANDSET and then press it again within 2

seconds.

NOTES

• When the phone successfully enters the CEC

battery charging testing mode, all handsets

display To register HS and See manual

alternatively.

• When the phone fails to enter this mode, repeat

Step 1 through Step 3 above.

To deactivate the CEC battery charging testing

mode:

1. Unplug the telephone base power adapter

from the power outlet, then plug it back in.

Then the telephone base is powered up as

normal.

2. Register your handsets back to the

telephone base. Refer to Register a

handset.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution,

suivez toujours ces mesures préventives de

base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les

instructions.

2. Observez toutes les instructions et

mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise

murale avant de le nettoyer. N’utilisez

pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux

et légèrement humecté.

4. N’utilisez pas ce produit près de l’eau,

tel que près d’un bain, d’un lavabo,

d’un évier de cuisine, d’un bac de

lavage ou d’une piscine, ou dans un

d’électrocution. N’échappez pas de

liquides dans l’appareil.

11. Aﬁn de réduire les risques

d’électrocution, ne démontez pas

l’appareil, mais apportez-le plutôt

à un centre de service qualiﬁé s’il

doit être réparé. En enlevant le

couvercle, vous vous exposez à des

tensions dangereuses ou autres

dangers similaires. Un remontage

inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation

ultérieure de l’appareil. Débranchez

l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide

et doux.

12. Ne surchargez pas les prises de

courant et les rallonges.

13. Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service à la clientèle

de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation

est endommagé ou écorché.

• Si du liquide a été échappé dans

l’appareil.

• Si l’appareil a été exposé à une

source d’humidité telle que la pluie

ou l’eau.

• Si le produit ne fonctionne pas

normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions

de fonctionnement. Les réglages

incorrects des autres commandes

pourraient provoquer un

dommage qui pourrait exiger un

travail exhaustif de la part d’un

technicien autorisé aﬁn de rétablir

le fonctionnement normal de

l’appareil.

• Si le produit a été échappé et que

le socle et/ou le combiné a été

endommagé.

sous-sol humide ou sous la douche.

5. Ne déposez pas ce téléphone sur un

chariot, support ou table chancelants.

L’appareil pourrait tomber et être

sérieusement endommagé.

6. Évitez d’installer le système

téléphonique dans les endroits

soumis à une température extrême,

à la lumière directe du soleil ou à

proximité immédiate d’autres appareils

électriques ou électroniques. Protégez

votre téléphone contre les sources

d’humidité, la poussière, les vapeurs et

les liquides corrosifs.

7. Le boîtier de l’appareil est doté de

fentes et d’ouvertures d’aération

situées à l’arrière ou en dessous.

Aﬁn d’empêcher la surchauffe, ces

ouvertures ne doivent pas être

obstruées en plaçant l’appareil sur

un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à

proximité d’un élément de chauffage

ni d’une plinthe électrique. De plus, ne

l’installez pas dans une unité murale ou

un cabinet fermé qui ne possède pas

d’aération adéquate.

8. Ne faites fonctionner cet appareil

qu’avec le type d’alimentation indiqué

sur les étiquettes de l’appareil. Si vous

ne connaissez pas le voltage de votre

maison, consultez votre marchand ou

votre fournisseur d’électricité.

9. Ne déposez rien sur le cordon

d’alimentation. Installez cet appareil

dans un endroit sécuritaire, là où

personne ne pourra trébucher sur

la ligne d’alimentation ni le cordon

téléphonique modulaire.

10. N’insérez jamais d’objets à travers

les fentes et ouvertures de cet

appareil, car ils pourraient toucher

à des points de tension dangereux

ou court-circuiter des pièces, ce qui

constituerait un risque d’incendie ou

• Si le produit afﬁche une nette

diminution de sa performance.

14. Évitez d’utiliser un téléphone (autre

qu’un sans ﬁl) pendant un orage. Les

éclairs peuvent être à l’origine d’une

électrocution.

15. N’utilisez pas le téléphone pour

rapporter une fuite de gaz à proximité

de la fuite. En certaines circonstances,

une ﬂammèche pourrait être

provoquée lorsque l’adaptateur

est branché à une prise de courant,

ou lorsque le combiné est déposé

sur le socle. Ceci est un événement

commun associé à la fermeture d’un

circuit électrique. L’utilisateur ne

devrait pas brancher le téléphone à

une prise de courant, et ne devrait

pas déposer le combiné chargé sur

le socle, si le téléphone se trouve à

proximité d’un endroit comportant des

concentrations de gaz inﬂammables, à

moins que la ventilation soit adéquate.

Une ﬂammèche dans un tel endroit

pourrait provoquer un incendie ou

une explosion. De tels environnements

peuvent comprendre: des endroits

où l’on utilise de l’oxygène médical

sans ventilation adéquate; des gaz

industriels (dissolvants de nettoyage,

des vapeurs d’essence, etc.); une fuite

de gaz naturel, etc.

16. Ne placez que le combiné de votre

téléphone près de votre oreille

lorsqu’en mode de conversation.

17. Ces adaptateurs ont été conçus pour

être orientés en position verticale ou

montés au sol. Les broches ne sont pas

conçues pour maintenir l’adaptateur en

place si celui-ci est barnché dans une

prise au plafond ou sous une table/

armoire.

CONSERVEZ CES INSTRUCTIONS

26 27

Pile

• MISE EN GARDE : N’utilisez que la pile

incluse.

• Ne jetez pas la pile au feu. Vériﬁez les

instructions spéciﬁques de mise aux

rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est

corrosif et pourrait causer des brûlures

ou des blessures aux yeux ou à la peau.

L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez

les piles aﬁn d’éviter les courts-

circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet

appareil, selon les instructions et limites

spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés

dans l’organisme

Les simulateurs cardiaques (s’applique

uniquement aux téléphones numériques

sans ﬁl) :

L’organisme ‘Wireless Technology

Research, LLC (WTR)’, une ﬁrme de

recherche indépendante, a mené

une évaluation pluridisciplinaire des

interférences entre les téléphones sans

ﬁl portatifs et les stimulateurs cardiaques

implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues

(FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs

cardiaques

• Ils doivent tenir le téléphone sans ﬁl à

une distance d’au moins six pouces du

stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone

sans ﬁl directement sur le stimulateur

cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

présence de parasites, il est conseillé

d’éloigner le téléphone sans ﬁl du

téléviseur ou du magnétoscope aﬁn de

réduire possiblement les interférences.

• Piles rechargeables : Manipulez les

piles avec soin aﬁn de ne pas les court-

circuiter avec des bagues, bracelets ou

clés. Les piles ou le conducteur peut

surchauffer et causer des blessures.

Respectez la polarité adéquate entre la

pile et le chargeur.

• Les bloc-piles rechargeables à l’hydrure

métallique de nickel : Jetez ces

blocs-piles de manière écologique et

sécuritaire. Ne les incinérez pas et ne

les percez pas. Tel que les autres piles

de ce type, elles pourraient dégager

une matière toxique qui peut causer

des blessures corporelles si elles sont

brûlées ou percées.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech product,

VTech Communications, Inc. (“VTech”),

warrants to the holder of a valid proof of

purchase (“Consumer” or “you”) that the

Product and all accessories provided by

VTech in sales package (“Product”) are

free from material defects in material and

workmanship, pursuant to the following

terms and conditions, when installed

and used normally and in accordance

with operating instructions. This limited

warranty extends only to the Consumer

for Products purchased and used in the

United States of America and Canada.

What will VTech Communications do if the

Product is not free from material defects

in materials and workmanship during

the limited warranty period (“Materially

Defective Product”)?

During the limited warranty period,

• Ils doivent utiliser le téléphone sans

ﬁl en l’appuyant sur l’oreille qui se

trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identiﬁé de risque pour les détenteurs

de simulateurs cardiaques causés par les

gens qui utilisent un téléphone sans ﬁl à

proximité de ceux-ci.

À propos des téléphones sans ﬁl

• Conﬁdentialité : Les mêmes

caractéristiques qui constituent des

avantages pour les téléphones sans ﬁl

afﬁchent également des restrictions.

Les appels téléphoniques sont transmis

entre le combiné sans ﬁl et le socle

par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations

téléphoniques sans ﬁl soient

interceptées par des équipements de

réception radio se trouvant dans la

portée du combiné sans ﬁl. Pour cette

raison, vous ne devez pas percevoir les

communications téléphoniques sans ﬁl

comme étant aussi conﬁdentielles que

celles des téléphones à cordons.

• Alimentation électrique : Le socle de

ce téléphone sans ﬁl doit être branché

à une prise électrique fonctionnelle.

La prise électrique ne doit pas être

contrôlée par un interrupteur mural. Les

appels ne pourront pas être effectués

du combiné sans ﬁl si le socle est

débranché ou mis hors tension ou si le

courant est coupé.

• Possibilité d’interférences aux

téléviseurs : Certains téléphones sans

ﬁl fonctionnent sur des fréquences

pouvant causer des interférences aux

téléviseurs et aux magnétoscopes.

Pour réduire ou prévenir de telles

interférences, ne placez pas le socle

du téléphone sans ﬁl près ou sur un

téléviseur ou magnétoscope. S’il y a

VTech’s authorized service representative

will replace at VTech’s option, without

charge, a Materially Defective Product.

If we choose to replace the Product, we

may replace it with a new or refurbished

Product of the same or similar design.

VTech will return replacement products to

you in working condition. VTech will retain

defective parts, modules, or equipment.

Replacement of the Product, at VTech’s

option, is your exclusive remedy. You

should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the

product extends for ONE (1) YEAR from

date of purchase (90 days on products

purchased as Refurbished*). This limited

warranty also applies to replacement

Products for a period of either (a) 90 days

from the date the replacement Product is

shipped to you or (b) the time remaining

on the original one-year limited warranty

(90-day limited warranty on products that

are purchased as Refurbished*), whichever

is longer.

*Refurbished products purchased from our

online store carry a 90-day replacement

warranty.

What is not covered by this limited

warranty?

This limited warranty does not cover:

1. Product that has been subjected

to misuse, accident, shipping or

other physical damage, improper

installation, abnormal operation or

handling, neglect, inundation, ﬁre,

water or other liquid intrusion; or

2. Product that has been damaged due

to repair, alteration or modiﬁcation

by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem

experienced is caused by signal

28 29

conditions, network reliability or cable

or antenna systems; or

4. Product to the extent that the problem

is caused by use with non-VTech

electrical accessories; or

5. Product whose warranty/quality

stickers, Product serial number plates

or electronic serial numbers have

been removed, altered or rendered

illegible; or

6. Product purchased, used, serviced, or

shipped for repair from outside the

United States, or used for commercial

or institutional purposes (including but

not limited to Products used for rental

purposes); or

7. Product returned without valid proof

of purchase (see 2 below); or

8. Charges for installation or set up,

adjustment of customer controls, and

installation or repair of systems outside

the unit.

How do you get warranty service?

To obtain warranty service in the United

States of America, please visit our website

at www.vtechphones.com or call 1 (800)

595-9511 for instructions regarding where

to return the Product. In Canada, go to

phones.vtechcanada.com or dial 1 (800)

267-7377.

NOTE: Before calling for service, please

review the user’s manual - a check of the

Product’s controls and features may save

you a service call.

Except as provided by applicable law,

you assume the risk of loss or damage

during transit and transportation and

are responsible for delivery or handling

charges incurred in the transport of

Product(s) to the service location. VTech

will return replaced product under this

limited warranty to you, transportation,

delivery or handling charges prepaid.

VTech assumes no risk for damage or loss

of the Product in transit.

What must you return with the Product to

get warranty service?

1. Return the entire original package

and contents including the Product to

the VTech service location along with

a description of the malfunction or

difﬁculty;

2. Include “valid proof of purchase”

(sales receipt) identifying the Product

purchased (Product model) and the

date of purchase or receipt; and

3. Provide your name, complete

and correct mailing address, and

telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech.

It supersedes all other written or oral

communications related to this product.

VTech provides no other warranties for

this product. The warranty exclusively

describes all of VTech’s responsibilities

regarding the product.

There are no other expressed

warranties. No one is authorized to make

modiﬁcations to this warranty and you

should not rely on any such modiﬁcation.

State Law Rights: This warranty gives you

speciﬁc legal rights, and you may also have

other rights which vary from state to state.

Limitations: Implied warranties, including

those of ﬁtness for a particular purpose

and merchantability (an unwritten warranty

that the product is ﬁt for ordinary use) are

limited to one year from date of purchase.

Some states do not allow limitations on

how long an implied warranty lasts, so the

above limitation may not apply to you.

In no event shall VTech be liable for any

indirect, special, incidental, consequential,

or similar damages (including, but not

limited to lost proﬁts or revenue, inability

to use the product, or other associated

equipment, the cost of substitute

equipment, and claims by third parties)

resulting from the use of this product.

Some states do not allow the exclusion or

limitation of incidental or consequential

damages, so the above limitation or

exclusion may not apply to you.

Please retain your original sales

receipt as proof of purchase.

Disclaimer and Limitation of

Liability

VTech Communications, Inc. and its

suppliers assume no responsibility for any

damage or loss resulting from the use of

this user’s manual. VTech Communications,

Inc. and its suppliers assume no

responsibility for any loss or claims by third

parties that may arise through the use of

this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square

Road - Ste 555 Tigard, OR 97223, United

States

Phone: 1 (800) 595-9511 in the U.S. or

1 (800) 267-7377 in Canada

Technical speciﬁcations

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency 1921.536-1928.448 MHz

Channels 5

Nominal

effective

range

Maximum power allowed by

FCC and IC. Actual operating

range may vary according to

environmental conditions at the

time of use.

Power

requirements Handset: 2.4V Ni-MH battery

Telephone base:

6V DC @ 400mA

Charger: 6V DC @ 400mA

Memory Directory:

30 memory locations;

up to 30 digits and

15 characters

Caller ID log:

30 memory locations;

up to 24 digits and

15 characters

VTech Communications, Inc.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Speciﬁcations are subject to change without notice.

Designed to ﬁt your home.

And your life.

VTech CS6114 Manuel utilisateur

Marque: VTech

Modèle: CS6114

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6114 User manual

VTech CS6114 Manuel utilisateur

Ce manuel convient également à

VTech CS6114 Manuel utilisateur

dans d''autres langues

Documents connexes