Pentair Pool Racer Pressure Side Pool Cleaner Le manuel du propriétaire

ENGLISH 1 ESPAÑOL 17 FRANÇAIS 37

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION AND

USER’S GUIDE

RACER®

PRESSURE SIDE POOL CLEANER

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

i

P/N 371004 Rev. D 3/30/17

If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please contact:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support, USA

(8 A.M. to 5 P.M. — Eastern/Paciﬁc Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web site

Visit www.pentairpool.com or www.staritepool.com

Sanford, North Carolina (8 A.M. to 5 P.M. ET)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 5 P.M. PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

TABLE OF CONTENTS

Maintenance .........................................................

Wall Fitting Screen

Tires

Roller Rings

Debris Bags

Sweep Hose

Backwashing the Pool Filter

Storage and Winterizing

Replacement Parts ..............................................

Parts List

Troubleshooting ....................................................

Steep Vinyl Liner Transitions

Important Warning and

Safety Instructions ..............................................

Important Information ..........................................

Cleaner Components

Overview

Installation ...........................................................

Booster Pump Installation

Installing the Wall Fitting and Adapter

Setting the Water Flow to Cleaner

Calculating Cleaner Speed/RPM

Adjusting the Hoses to Fit Pool

Assembling the Cleaner

Using the Cleaner

Cleaner Adjustments and Operation ..................

Cleaner Operation

Adjusting the Thrust Jet

Cleaning the Debris Bag

Adjusting the Sweep Hose Regulator

ii

1

2

3

4

6

7

8

9

10

12

13

14

16

All Pentair trademarks and logos are owned by Pentair or one of its global afﬁliates. Pentair Aquatic Systems®, Night Cruize®

and RACER® are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its afﬁliated companies

in the United States and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in

this document are not used to indicate an afﬁliation or endorsement between the owners of these names and brands and

Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those third

parties. Because we are continuously improving our products and services, Pentair reserves the right to change speciﬁcations

without prior notice. Pentair is an equal opportunity employer.

This document is subject to change without notice.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

ii

ESPAÑOL 20 FRANÇAIS 43

ENGLISH

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

Attention Installer: This guide contains important information about the

installation, operation and safe use of this product. This information should

be given to the owner and/or operator of this equipment after installation

of the pool cleaner.

Attention User: This manual contains important information that will help

you in operating and maintaining this pool cleaner. Please retain it for future

reference. Consult Pentair with any questions regarding this equipment.

Important Notice:

Before installing this product, read and follow all

warning notices and instructions which are included.

Failure to follow safety warnings and instructions can result in severe

injury, death, or property damage. Call (800) 831-7133 for additional free

copies of these instructions.

Stop pump before attempting to clean unit. Do

not allow swimmers in pool while pool cleaner is

operating.

To reduce the risk of injury, do not let children use

or play with pool cleaner.

Do not allow swimmers in the pool while pool cleaner

is operating. Hose can trip or entangle

swimmers which could result in drowning.

Consumer Information and Safety

This pool cleaner is designed and manufactured to provide many years

of safe and reliable service when installed, operated and maintained

according to the information in this manual. Throughout the manual, safety

warnings and cautions are identiﬁed by the “ ” symbol. Be sure to read

and comply with all of the warnings and cautions.

HAZARDOUS SUCTION.

Do not play with cleaner or hose or apply to body.

Can trap and tear hair or body parts. Hose can trip or

entangle swimmers which could result in drowning.

SUCTION ENTRAPMENT, INJURY, AND

DROWNING HAZARD. If your pool has a dedicated

suction port (“vac port”) for vacuuming or for an

automatic pool cleaner, it must be covered when

not in use. A spring loaded safety cover (a “vac port

ﬁtting”) is included with your cleaner. Install it on the

suction port to prevent entrapment and injury. If the

cover provided does not ﬁt, purchase one that does

from your local pool store and install it instead. The

cover should conform to IAPMO SPS4-99A.

General Installation Information

Pre-Installation Check List

Before installing your cleaner, review and understand all warnings and

safety information in this guide. Failure to follow these instructions or

improper installation of the cleaner can result in damage to the pool

ﬁnish or the vinyl liner. Most cleaners are not designed to traverse from

ﬂoor to wall when the pool cove is 90%. There may be other structures

installed in the pool that the cleaner cannot navigate, BE AWARE and

supervise the cleaner during unique conditions. Pentair Aquatic Systems

disclaims any liability for repairs or replacement to any of these structures

or components of the customer’s pool.

Before installing the cleaner in a vinyl liner pool:

Check liner closely for signs of deterioration or damage from age,

chemicals, pool wall damage, etc. If any damage is found, have a qualiﬁed

pool professional make all the necessary repairs. Also, if there are stones,

roots, etc., under the liner, remove them before installing the cleaner.

Before installing the cleaner in a gunite pool or a pool that is partially

or completely tiled:

Make sure pool ﬁnish is in proper condition as staining, etching, cracking

or delaminating may worsen.

Repair loose tiles and tighten any loose light rings.

Before installing the cleaner, clean your ﬁlter system:

Make sure you have cleaned the ﬁlter, including backwashing, rinsing,

and emptying all baskets. A clean system is necessary for proper cleaner

operation and coverage.

Before installing the cleaner, understand cleaner coverage:

The cleaner is designed to rid your pool of debris in approximately 4-6

hours. Less time could be needed, depending on the pool size. The cleaner

was not designed to automatically clean steps or swimouts, or to work

under a solar cover. The cleaner may get stuck in these areas which can

result in damage to the pool ﬁnish or vinyl liner. Pentair Aquatic Systems

disclaims any liability for repairs or replacement to any of these structures

or components of the consumer’s pool. It was also not designed to do

initial cleanup for a new pool or when opening your pool for the season.

AFTER installing the cleaner, make sure the cleaner is operating

correctly:

The cleaner may need some minor adjustments to make sure it is

operating properly so there is no damage to the pool ﬁnish. Certain

vinyl liner patterns are particularly susceptible to surface wear, pattern

removal, ink rubbing off of, or serious scratches to the pattern caused by

objects coming into contact with the vinyl surface, including automatic

pool cleaners. Pentair Aquatic Systems is not responsible for any pattern

removal, abrasions or markings on vinyl liners. Periodically inspect the

cleaner components and the cleaner performance to ensure it is operating

as designed. Replace and/or repair any worn or damages components.

Failure to follow instructions or improper installation of the cleaner may

result in damage to the cleaner, pool ﬁnish or the vinyl liner.

Moving parts may injure hands or ﬁngers. Stop pump

before attempting to clean out pool cleaner head.

Warnings and safety instructions for Pentair Aquatic Systems

pumps and other related products are available at:

http://www.pentairpool.com/support/product-warnings.html or

call (800) 831-7133 for additional free copies of these instructions.

Please refer to http://www.pentairpool.com/support/product-

warnings.html for warning and safety instructions related to

this product.

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Before the cleaner is installed, please take a moment to record the

serial number. This number is located on your warranty card and

on the back of the cleaner near the rear jets. You will be asked for

this number when you contact our Technical Support Department.

SERIAL #__________________________________

iii

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

Disclaimer of Liability

About your Pool and Pressure Side Pool Cleaner

There are a multitude of factors that contribute to the life of your pool. The

pool cleaner is a very passive product that will have no impact on pool life.

Please be aware that over time, deterioration, discoloration and brittleness

of any pool ﬁnish can be caused separately by, or in combination with,

age, an imbalance in pool water chemistry, improper installation and other

factors. Pressure side pool cleaners will not remove or cause wear on

“good” pool plaster. In fact, the opposite is true–pool plaster will eventually

cause wear on the cleaner.

The same situation holds true for vinyl-lined in-ground swimming pools,

because vinyl liners are also affected by the environment and factors such

as pool water chemistry, sunlight and the pool’s surroundings. Therefore

over time, vinyl can become brittle and weak. In addition, vinyl-lined pools

are affected by the workmanship, composition and installation of the

liner and the workmanship and quality of construction of the supporting

walls and pool base. These are all factors which can contribute to liner

failure. The existence of any of these type of conditions in your pool is

not caused by the use or operation of the pool cleaner. The manufacturer

disclaims any liability for repairs or replacement to any of these structures

or components of the customer’s pool.

The pool owner must assume all responsibility for the condition and

maintenance of the pool’s surface, water and deck.

SAVE THESE INSTRUCTIONS

1

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

OVERVIEW

Overview

The RACER® Pressure Side Pool Cleaner moves

through a sequence of straight, right and left turns

helping to increase pool coverage, vacuuming and

scrubbing your entire pool.

• For continuous uninterrupted cleaning, the cleaner

will go into reverse mode about every two minutes,

which allows it to efﬁciently clean the entire pool.

Note: Before you install and operate your cleaner,

read through these important guidelines:

1. Always disconnect the cleaner from the pool wall

when cleaning or back washing the pool ﬁlter.

2. After cleaning or back washing the ﬁlter, let the

ﬁltration system run for at least ﬁve minutes before

reconnecting the cleaner.

3. New plumbing lines should be ﬂushed out before

installing the cleaner.

4. The cleaner should not be used to remove plaster

dust in new pools.

5. Always remove the cleaner before swimmers enter

the pool.

6. Always handle the cleaner with care.

7. Always pick up the cleaner by the handle,

especially when lifting the unit out of the water.

8. Do not handle the cleaner while it is operating.

9. Always remove the cleaner from the pool before

chemical shock treatments (super chlorinate). As a

rule, any pool water that is unsafe for swimming is

unsafe for the cleaner.

10. Carefully cut the feed hose following the

instructions on page 4.

11. By following these simple guidelines, you can help

protect against injury and prolong the life of your

cleaner.

12. Refer to “Important Warning And Safety

Instructions” on pages ii - iii for additional

installation and safety information.

13. Before you install your RACER pool cleaner:

If there is a chlorinator, solar system, ozone

generator or air inducing equipment installed,

contact Technical Support at 1-800-831-7133.

Night Cruize ® LED

1. RACER Cleaner Head

2. Debris Bag

3. Sweep Hose (not needed in

most pools)

4. Feed Hose Assembly - Not

shown (3-10 ft. [3 m.] sections)

5. Wall Fitting

6. Wall Adapter

7. Debris Seal

Note: The cleaner system is delivered

with debris seal installed inside of

cleaner head.

8. Flow Gauge

ENGLISH

Cleaner Components

1

2

5

6

8

7

3

2

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Booster Pump Installation

Please refer to the instructions included with your

booster pump for installation information.

Please follow these instructions carefully.

IMPORTANT! Before starting this procedure

be sure to switch off the ﬁlter pump and

booster pump.

1. Attach the ﬂow gauge to the wall ﬁtting by aligning the two

tabs on the ﬂow gauge with the grooves in the wall ﬁtting.

See ﬁgure 2. Push and turn the ﬂow gauge clockwise until

it stops, then slightly pull it out away from the wall. Be

sure the ﬂow gauge is securely locked in place by turning

it counterclockwise while slightly pulling out on the ﬂow

gauge. See ﬁgure 3.

Note: Flow gauge will not turn when locked in place.

2. Switch on the ﬁlter pump and then the booster pump.

3. Verify the white plunger (inside the ﬂow gauge) is aligned

within the box on the ﬂow gauge. See ﬁgure 4.

4. Adjust the valve on the wall ﬁtting using a ﬂathead screw

driver by turning the valve clockwise (to reduce ﬂow) or

counter-clockwise (to increase ﬂow) so that the white

plunger aligns with the arrows on the ﬂow gauge markings.

See ﬁgure 5.

5. Switch off the booster pump and then the ﬁlter pump.

6. Remove the ﬂow gauge from the wall ﬁtting by pushing in

and turning counterclockwise and pulling the gauge out.

7. Attach the hose assembly to the wall ﬁtting. Turn clockwise

then push in one quarter turn to secure in place (as

described in Step 1).

Setting the Water Flow to the Cleaner

Figure 2.

Turn counterclockwise

to OPEN

Figure 3.

Figure 4. Figure 5.

Wall Fitting

Align Tabs

Wall Fitting

Flow Gauge

Max Flow

Min Flow

INSTALLATION

1. Remove and disconnect any existing pool cleaner

and/or wall ﬁtting.

2. Switch on the ﬁltration pump and booster pump, to

ﬂush out the plumbing line.

3. Switch off ﬁlter pump and booster pump.

4. Insert wall ﬁtting adapter into the dedicated 1-1/2”

NPT threaded return line. Hand tighten until snug.

See ﬁgure 1.

5. Align wall ﬁtting with the quick lock pegs inside the

wall adapter. Push the wall ﬁtting into the wall adapter

until it bottoms out. Twist 1/4 turn clockwise to lock

the wall ﬁtting. Pull gently outward to engage quick

lock pegs. See ﬁgure 1.

Installing the Wall Fitting and Wall Adapter

Figure 1.

Installing the Wall Fitting

LOW

HI

Wall Adapter

(Shown Installed)

O-Ring

Wall Fitting

Quick

Lock Peg

3

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Cleaner Body

ENGLISH

Calculating Cleaner Speed/RPM

1. To determine whether the RACER® Pressure Side Pool Cleaner is receiving the proper water pressure,

turn off the pool pump, and carefully remove the cleaner from the pool.

2. Mark the front tire/wheel with a marker, such as a blade of grass stuck under the tire.

3. Have someone restart the pool pump and booster pump while you place the cleaner just beneath the

pool’s water surface.

Note: Be sure to hold onto the sweep hose (if installed) to avoid getting wet, as ﬂow will return to the

sweep hose regulator when the pump is restarted.

4. Count the number of full rotations made by the marked wheel over a period of one minute. The number of

rotations will give you the revolutions per minute; or RPM’s.

Note: Be sure that the back-up valve isn’t cycling at this time.

5. For proper performance, the RACER cleaner operates between 31 - 33 RPM’s with a sweep hose

installed and 33 - 36 RPM’s without a sweep hose.

If the RPM is below 31 with a sweep hose installed, or below 33 without a sweep hose, then call your

local Pool Professional or contact Pentair’s Technical Support Department at 1-800-831-7133.

If the RPM is higher than 33 with a sweep hose installed, or higher than 36 without a sweep hose, at the

wall ﬁtting adjust the valve, as described under “Setting the Water Flow to the Cleaner” on page 2, until

the RPM falls back into the optimal range.

4

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Measure Deepest Part of Pool

Main Drain

Adjusting the Hose Assembly to Fit Pool

The hose assembly consists of: Three (3) 10 ft. [3 meters]

sections, one (1) soft light grey lead hose marked as

section one and two (2) stiffer dark grey feed hoses

marked as sections two and three.

Important to the Performance of the Cleaner:

Measure, cut, and assemble the hose sections as

described in Step 1 and Step 2. Use strong scissors or a

sharp knife to cut the hoses. Be sure to slide the ﬂoats out

of the way when cutting hose. Cut hose ends as straight as

possible.

Step 1: Sizing Hose Section 1

1. Measure the deepest part of the pool. See ﬁgure 6.

Note: The grate or domed main drain, at the bottom

of the pool, is usually the deepest point. If the depth is

greater than 10 ft. [3 meters], do not cut the hose, and

proceed to Step 2.

2. If the pool depth is less than 10 ft. [3 meters],

disconnect the soft light grey lead hose, labeled

section one, from the swivel end. Cut the lead hose so

the length is equal to the deepest part of the pool. See

ﬁgure 7.

Example: If the pool is 8.5 ft. [2.6 meters] deep, cut

1.5 ft. [.5 meters] off of the hose labelled section one

(since the hose is 10 ft. [3 meters]).

3. Discard excess hose. Reconnect the newly cut lead

hose to the swivel on the feed hose. All three hose

sections should now be connected.

Step 2: Sizing Hose Sections 2 and 3

1. Attach the hose assembly to the wall ﬁtting. See ﬁgure

8. Then attach the wall ﬁtting (with hose) to the wall

adaptor. See ﬁgure 8. Take the opposite end of the hose

assembly and walk to the farthest point of the pool from

the wall adaptor. To prevent over stretching the hose,

rest the hose on top of the pool water. Measure the

excess hose length (hose that extends beyond pool

edge). This determines the amount of hose to be cut

from sections 2 and 3.

2. Disconnect feed hose assembly from the wall adaptor.

Disconnect sections 2 and 3 from the ﬁrst swivel closest

to the wall ﬁtting.

3. Cut half of the total excess hose length from each hose

labeled section 2 and section 3 (assembled with four

ﬂoats) equally. Both feed hose sections should be

the same length after cutting.

Example: If there is 6 ft. [1.8 meters]of excess hose.

Cut 3 ft. [.9 meters] off of section 2 and section 3. (Half

of 6 ft. [1.8 meters] = 3 ft. [.9 meters] each)

If more than 3 ft. [.9 meters] is cut from each hose section,

remove one (1) ﬂoat from each hose section.

Note: For large pools requiring extra hose lengths you

will need to purchase one (1) additional hose, P/N 360266

(10 ft. [3 meters] single hose). Attach extra hose sections

at the wall ﬁtting using supplied swivel and mender nuts.

Figure 9.

Figure 8.

Figure 6.

Figure 7.

Wall Fitting

Hose Assembly

Measuring the Lead Hose

Lead Hose Length = Deepest Part of Pool

Float Quick

Connect Fitting

(connects to

cleaner)

Swivel

7½ FT. (2,3 M.)

EXAMPLE DIMENSION

(Your Measurement May Differ)

NOT TO SCALE

MARKED SWIVEL

FARTHEST POINT OF POOL PERIMETER FROM WALL FITTING

10 FOOT (3 METER)

WHITE OR GREY

HOSE SECTION

10 FOOT (3 METER)

WHITE OR GREY

HOSE SECTION

10 FOOT (3 METER)

SOFT HOSE

REMOVE EXCESS MATERIAL

FROM HOSE ON EITHER SIDE OF

MARKED SWIVEL AS DESCRIBED

IN STEPS 2 AND 3.

WALL FITTING

SWIVEL

FLOATS

5

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Step 3: Connecting Hose Sections

1. After the hose sections have been cut to size,

reconnect them by pushing the hose end over

the barb on the swivel.

Note: Be sure to push the hose all the way to

the bottom of the barb.

2. Move the mender nut toward the hose by turning

clockwise and rotating until tight on hose. Use

pliers if needed.

Note: Be sure the same number of ﬂoats are left

on hose sections 2 and 3, as described in Step 2

on page 4.

3. To check that the hose is cut to the correct

length, reconnect the hose and wall ﬁtting to the

wall adaptor. Take the opposite end of the hose

assembly and walk to the farthest point of the

pool from the wall adaptor. The hose should

reach the edge of the pool but should not extend

more than 6 inches beyond the pool edge.

4. You can now connect the cleaner to the hose.

Connecting the Hoses to Swivels

Barb on

Swivel

Feed

Hose

Mender Nut

WATER FLOW

DIRECTION

Figure 10.

Figure 11.

ENGLISH

Wall Fitting

Furthest Point of

Pool Perimeter

Feed Hose

(1)

First Swivel

Second Swivel

Feed Hose

(2)

Lead

Hose

Measuring the Feed Hoses

6

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Assembling the Cleaner

1. Attach the Quick Connect ﬁtting on the end of the hose to the feed tube on the RACER® Pressure Side Pool Cleaner.

Be sure the snaps are engaged.

2. Attach the debris bag to the cleaner. Push the bag over vacuum tube to click it into place.

3. Review checklist before use:

• Hoses cut properly and ﬂoats evenly spaced.

• Mender nuts are tight on feed hose.

• Wall ﬁtting secure and in place.

• Debris bag and hose assembly attached.

• Ensure debris seal is attached. See ﬁgure 12.

Using the Cleaner

1. Lower the cleaner carefully into pool.

2. Switch ON the FILTER PUMP.

3. Wait at least 60 seconds to allow air to blow out of the hose.

4. Switch ON the BOOSTER PUMP.

Assembling the Cleaner

Debris Bag

Optional

Sweep Hose

Quick Connect Fitting

(with built-in swivel)

Feed Tube

Lead Hose

Mender Nut

Night Cruize® (both sides)

Debris Seal

Figure 12. Feed Tube

7

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

CLEANER ADJUSTMENTS AND OPERATION

Cleaner Operation

Note: The RACER® Pressure Side Pool Cleaner may need some minor adjustments to ensure it is operating properly

and to get the best performance possible.

When operating correctly, the cleaner will travel in a random pattern throughout the pool, vacuuming and scrubbing

the pool.

• The climbing ability of the cleaner depends on the pool structure and water ﬂow.

• One hour cleaning cycle is recommended for average size residential (15’ x 30’ [4.6 m x 9.1 m]) pools.

• It will perform more efﬁciently in pools without sharp transitions between pool ﬂoor and walls.

• The cleaner goes into a reverse mode approximately every 2-1/2 minutes for approximately 15 seconds.

• If pool has a high level of debris, run the cleaner in two short cycles. Empty the debris bag between cycles.

Figure 13.

Figure 14.

ENGLISH

Sweep Hose

Regulator

12

6

9 3

M

o

v

e

s

C

l

e

a

n

e

r

L

e

f

t

M

o

v

e

s

C

l

e

a

n

e

r

R

i

g

h

t

I

n

c

r

e

a

s

e

s

C

l

i

m

b

i

n

g

D

e

c

r

e

a

s

e

s

C

l

i

m

b

i

n

g

Adjusting the Thrust Jet

The thrust jet is at the back of the cleaner below the sweep hose regulator, and helps to power the direction of the

cleaner. See ﬁgure 13.

You may need to adjust the thrust jet based on the pool shape, in order to get maximum cleaner coverage.

The alternate jet position shown below can help the climbing ability of the cleaner. See ﬁgure 14.

Thrust Jet

12

9

6

3

Factory Jet Position

Straight Out

Alternate Jet Position

10 o-clock Position

8

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Cleaning the Debris Bag

1. Detach the bag strap from the hose.

2. Press the release button on the cleaner vacuum tube and carefully pull up to remove the bag from the cleaner.

See ﬁgure 15.

3. Open bag closure by pulling apart the fabric tabs at the top of the bag (see ﬁgure 16). Holding the bottom

of the bag, turn over to empty debris out of the top. If needed, rinse bag with a hose.

4. To close, press together the hook and loop fabric at the top of the bag and run ﬁnger along entire length of

bag so it is completely closed.

5. Be sure debris seal is on the vacuum tube. See ﬁgure 12 on page 6.

6. Slide the debris bag collar over the vacuum tube until it clicks in place.

7. Reattach the strap onto the feed hose.

8. To keep bag from folding during operation, attach the strap above ﬁrst feed line ﬂoat. Slide ﬂoat down if needed.

Note: It is easier to empty the debris bag when it is dry. A second bag (purchased separately) may be used

while the used debris bag is drying.

Use tabs to pull

bag apart

Debris Bag

Figure 15.

Figure 16.

Bag Release

Button

9

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

ENGLISH

Adjusting the Sweep Hose Regulator when

Sweep Hose is Installed

The sweep hose operates in a gentle sweeping motion to

clean debris from hard to reach corners of pools. See ﬁgure

17.

Note: 1. Do not adjust the sweep hose regulator while

cleaner is operational. This may damage cleaner.

2. The sweep hose must be used to adjust the

sweep hose regulator.

1. If you do not plan on using the optional sweep hose, there

is nothing more you need to do. To attach the optional

sweep hose to the cleaner and open the sweep hose

regulator, proceed to Step 2.

2. To attach the sweep hose to the RACER® Pressure Side

Pool Cleaner, line up the lock tabs on the inside of the

sweep hose ﬁtting (small round ﬁtting on the end of the

sweep hose) to the locking slots on the cleaner’s sweep

hose regulator. See ﬁgure 18.

3. The sweep hose regulator comes from the factory in the

closed position. To open the sweep hose regulator, push

the sweep hose ﬁtting onto the sweep hose regulator.

When it can not be pushed any further turn the sweep

hose ﬁtting clockwise until it stops (about 45 degrees).

See ﬁgure 19. Pull out on the sweep hose ﬁtting and

the ﬁtting will lock into place.

4. To remove the sweep hose and turn off the sweep

hose regulator, hold the sweep hose ﬁtting and turn it

counter-clockwise until it stops (about 45 degrees). See

ﬁgure 19. Pull the sweep hose ﬁtting from the sweep

hose regulator and store it in a safe place.

Sweep Hose

Regulator

Sweep Hose Sweep Hose

Fitting

To Close

To Open

Open

Position

Closed

Position

Locking

Slot

Sweep Hose Regulator

Lock Tab

Sweep Hose Fitting

Figure 18.

Figure 19.

Figure 17.

10

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

MAINTENANCE

Periodic Maintenance

Periodically inspect the RACER® Pressure Side Pool

Cleaner and its components. Replace and/or repair any

worn or damaged components. Failure to follow instructions

or improper installation of the cleaner can result in damage

to the cleaner, pool ﬁnish, or vinyl liner.

The following parts are wear items that should be inspected

periodically and replaced as needed.

Wall Fitting Screen

Inside the wall ﬁtting is a stainless steel ﬁlter screen that

acts as a secondary ﬁlter. This screen captures debris

that may have passed through the pool ﬁlter.

A dirty screen may be an indication of potential

issues in your pool ﬁlter system and you may need to

contact your local pool professional.

Note: Running the cleaner without the ﬁlter screen can

damage the cleaner and void the warranty.

To clean the ﬁlter screen:

1. Switch the booster pump and then the ﬁltration pump off.

2. Remove the wall ﬁtting from the wall adaptor.

3. Pull the screen out from inside the wall ﬁtting.

4. Rinse thoroughly until clean and insert back inside the

wall ﬁtting.

5. Whenever cleaning, backwashing or repairing the pool

ﬁlter, also clean the wall ﬁtting screen after your ﬁrst

cleaner cycle.

Tires

The tires are designed to protect the bottom of your

pool and provide traction. Tires will wear and need to be

replaced occasionally.

Debris Bags

The cleaner comes with a general purpose bag and is

used for all debris types. Replace bag when the fabric is

torn or punctured.

Note: To prolong the life of your cleaner, remove it

from pool before adding chemicals.

Sweep Hose

The sweep hose is provided as an optional accessory

to help keep hard to reach corners of your pool clean.

Replace sweep hose scrubber as necessary if used.

Sweep Hose Roller Rings

Your sweep hose has a series of roller rings to protect

the sweep hose. Replace the rings as needed. Ensure

the roller rings rotate freely.

Backwashing the Pool Filter

Always disconnect the cleaner from the pool wall before

cleaning or backwashing the pool ﬁlter. After cleaning or

backwashing, let the pool ﬁltration system and booster

pump run for a minimum of ﬁve minutes to ﬂush out the

return lines before reconnecting the cleaner.

Storage and Winterizing

You may leave the wall adapter in the wall and

store the hoses straight, without any kinks. If storing

the hose coiled, be sure to lay the hose straight in the

sun for 12 to 24 hours before using again. Use the

ﬂow gauge to be sure the ﬂow is sufﬁcient for cleaner

operation.

Figure 20.

Cleaning the Filter Screen

Feed Hose

Mender Nut

Hose Connector

Wall Fitting

Filter Screen

11

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

[Blank Page]

ENGLISH

12

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Illustrated Parts List

27

14

32

24

15

5

4

18

25

31

34

33

28

2

1

2

8

3

11

2

6

27

6

26

27

47

46

464

7

22

37

42

21 23

38

36

48

REPLACEMENT PARTS

41

16

13

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Parts List

ENGLISH

ITEM

NO.

PART

NUMBER DESCRIPTION

1 360229 Top Front Cover Kit

2 360230 Rear Cover Kit

3 360231 Bottom Cover Kit

4 360391 Chassis Kit

5 360233 Front Grill Kit

6 360234 Side Covers Kit

7 360235 Large Wheel Kit

8 360236 Small Wheel Kit

9 360237 Large Tires Kit

10 360238 Scrubber Gear Kit

11 360239 Scrubber Kit

12* 360240 Debris Bag Kit (w/o collar), hook

and loop fastener

13* 360241 Debris Bag Collar Kit

14 360242 Vacuum Tube Kit

15 360243 Debris Valve Kit

16 360244 Sweep Hose Kit

17 360245 Sweep Hose Scrubber Kit

18 360246 Gear Box Kit

19 360247 Timer Valve Kit

20 360248 LED Kit

21 360249 Feedline Swivel Kit

22 360250 Feedline Quick Connector Kit

23 360251 Feedline Wall Connector Kit

24 360252 Feed Line Connector Kit

25 360253 Drive Shaft Kit

ITEM

NO.

PART

NUMBER DESCRIPTION

26 LLC55PMB Wheel Screw Kit

27 360255 Screw Kit

28 360256 Turn Jet Hose Kit

29 360257 Rear Thrust Jet Hose Kit

30 360258 Rubber Button Kit

31 360414 Turbine Kit

32 360260 Venturi Manifold Kit

33 360261 Water Management Kit

34 360262 Turbine Hose Kit

35* 360263 Tune Up Kit

36 360264 Feed Line Hose Kit Complete

37 360265 Soft Feed Line Hose Kit 10’

38 360266 Hard Feed Line Hose Kit 10’

39 E24 Debris Screen

40 LL23PM Threaded Wall Adapter

41 EB10G Sweep Hose Wear Ring

42 360270 Feed Line Float

43* 360268 Feed Line O-Ring Kit

44* 360269 Debris Bag with Mechanical Lock

45* 360274 Wheel Hump Insert Kit

46 360434 Axle Kit

47 EC64 Wheel Washer Kit

48 360392 In-line Filter Kit

49 360437 Replacement Screen Cartridge

Note: (*) Not shown

14

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Problem Corrective Action

Cleaner doesn’t move or moves slowly. Ensure ﬁlter pump and booster pump are on and moving water. (You may need to

clean your pool ﬁlter system.)

Ensure the wall ﬁtting screen is free of debris; you may need to remove and rinse.

Check for proper ﬂow using Flow Gauge (provided). See page 2. Adjust the ﬂow at

the wall ﬁtting if needed. See page 2.

Check all feed hose connections and swivels for leaks.

Check for debris that may be jammed in the gear teeth on one of the front drive

wheels. Gently rotate the front wheels backward to dislodge debris.

Check to see if the rear wheels are spinning freely. Replace wheels if necessary.

Cleaner hangs at steps. Ensure the front (large) wheels reverse approximately every 2-1/2 minutes.

Cleaner tilts to one side. Usually indicates a full debris bag. Empty the debris bag (see page 8).

Note: Cleaner at times will tilt on one side (on two wheels) during a turn

cycle. Watch the cleaner for a few minutes to see if it positions itself upright.

Cleaner does not go in reverse. Ensure the front (large) wheels reverse approximately every 2-1/2 minutes.

Check for proper ﬂow using Flow Gauge (provided). See page 2. Adjust the ﬂow at

the wall ﬁtting if needed. See page 2.

Cleaner will not climb. Check debris bag. Empty the debris bag if full.

Check for proper ﬂow using Flow Gauge (provided). See page 2. Adjust the ﬂow at

the wall ﬁtting if needed. See page 2.

Reposition the thrust jet to increase climbing (see page 7).

Note: The climbing ability of the cleaner depends on pool shape and available

water ﬂow. It will climb better in pools without sharp angles or in the

transition from the pool ﬂoor to the pool wall.

Hoses tangling in loops. Check the length of the feed hose. If it is too long it may cause the hose to tangle or

loop. See page 4 for sizing feed hose.

Ensure the feed hose is ﬂoating on the pool surface. Hose ﬂoats should be spaced

approximately two feet apart. See page 4 for hose ﬂoat positioning.

Ensure the hose swivels spin freely. Replace swivels if tight.

Ensure the feed hose has no kinks or bends.

Sweep hose caught in vacuum tube. Ensure the sweep hose regulator valve is fully open. See page 9.

Booster pump very noisy. Ensure ﬁlter pump and booster pump are on and moving water. (You may need to

clean your pool ﬁlter system.)

Ensure wall ﬁtting is properly installed. If leaking, O-ring may need to be replaced.

Contact your local pool professional - possible booster pump issue.

Use the following troubleshooting information to solve potential issues with the RACER® Pressure Side Pool Cleaner.

TROUBLESHOOTING

15

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Problem Corrective Action

Brush on front of cleaner is not spinning. Watch front wheels while cleaner is operating in the pool. The wheels and front

brush should rotate simultaneously.

Ensure the scrubber is free of tangled debris.

Rear wheels dragging/not spinning. Ensure the wheel sleeve is free of tangled debris.

Note: You may need to remove the wheel by pulling straight off sleeve to

remove any tangled debris.

Rear wheels falling off. Replace wheel and wheel sleeve.

Night Cruize LEDs are not illuminated during

cleaner operation. (Note: LED operation does

not affect cleaner performance.)

Debris may be clogging generator turbine. To clean debris from generator turbine:

Find access hole under the left rear wheel by removing the wheel by pulling it

straight off cleaner. Use a large paper clip and insert approximately 2 in. [5 cm]

straight into the access hole, continue until the generator turbine paddle is felt and

move paper clip until paddle rotates. Rotate the paddle several times with paper

clip to clear the debris.

Insert paper clip in

access hole.

ENGLISH

16

RACER® Pressure Side Pool Cleaner Installation and User’s Guide

Steep Vinyl Liner Transitions

In some pools with deep diving ends the transition angle from the deep end to the shallow end may cause the

RACER® Pressure Side Pool Cleaner to have difﬁculty transitioning over this angle. If so, you may need to insert

the tire wedges provided to help the cleaner make this transition. These wedges create a hump in the tire and help

keep the cleaner from becoming obstructed. They are not required in all pools.

Note: Both wedges should be installed horizontally in line with each other. If they are not in line with each other

they may cause the cleaner to have difﬁculty with the transition angle. This is important for proper cleaner

operation. See ﬁgure 21.

1. To install the tire wedge, pull the rubber tire up from the plastic wheel and ﬁrmly push the insert between the

tire and wheel. The smooth surface on the underside of the wedge should be inserted ﬁrst, from the outside to

the inside of the cleaner wheels. See ﬁgure 22. Be sure that the slots on the plastic wheel and the slots on the

underside of the wedge lock into each other.

2. Push the wedge towards the nose of the cleaner body until the insert is securely seated behind the lip of the

rubber tire. See ﬁgure 21.

Tire Wedge

Figure 21. Figure 22.

La page charge ...

Pentair Pool Racer Pressure Side Pool Cleaner Le manuel du propriétaire

Pentair Pool Racer Pressure Side Pool Cleaner Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents