Vermeiren Trigo S Manuel utilisateur

User manual

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S

Ł

U G I

N Á V O D K O B S L U Z E

Trigo S

Instrukcje dla wyspecjalizowanego

No part of this manual may be reproduced in any form what so

ever (print, photocopy, microfilm or any other process) without

written permission of the publisher, or processed, duplicated or

distributed by using electronic systems.

Aucune partie de ce manuel ne peut être reproduite, sous

quelque forme que ce soit (imprimée, photocopie, microfilm ou

tout autre procédé) sans l'autorisation écrite du publicateur, ni

traitée, dupliquée ou distribuée à l'aide de systèmes

électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in enige

vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder

de schriftelijke toelating van de uitgever worden

gereproduceerd of met behulp van elektronische systemen

worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner Form

(Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren)

ohne schriftliche Genehmigung des Herausgebers

reproduziert oder unter Verwendung elektronischer Systeme

verarbeitet, vervielfältigt oder verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o

altro procedimento) senza l’autorizzazione scritta della casa

produttrice, né elaborato, duplicato o distribuito con l’ausilio di

sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente manual

de cualquier forma (impresión, fotocopia, microfilm o cualquier

otro procedimiento), así como la edición, copia o distribución

empleando sistemas electrónicos, sin el permiso escrito del

editor.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Żadna część niniejszej instrukcji nie może być powielana w

jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani

innej) bez pisemnej zgody wydawcy, nie może być również

przetwarzana, kopiowana ani rozprowadzana za pomocą

systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv způsobem

(tisk, kopie, mikrofilm nebo jiný způsob) bez písemného

souhlasu vydavatele, nebo zpracování, duplikace či distribuce

prostřednictvím elektronických systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: E, 2021-10

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : E, 2021-10

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: E, 2021-10

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: E, 2021-10

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: E, 2021-10

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: E, 2021-10

PL

sprzedawcy

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: E, 2021-10

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: E, 2021-10

Basic UDI: 5415174 122106Trigo S TV

Multi version: E, 2021-10

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Trigo S

2021-10

Content

1

EN

NL

Content

Content .......................................................................................................... 1

Preface .......................................................................................................... 2

1 Your product ...................................................................................... 3

1.1 Accessories ............................................................................... 4

2 Before use .......................................................................................... 5

2.1 Intended use ............................................................................. 5

2.2 General safety instructions ........................................................ 5

2.3 Transport ................................................................................... 6

2.4 Folding - unfolding ..................................................................... 8

2.5 (Dis)Assembling rear wheels ..................................................... 8

2.6 Storage ...................................................................................... 8

3 Using your wheelchair....................................................................... 9

3.1 Parking brakes .......................................................................... 9

3.2 Push handles .......................................................................... 10

3.3 Armrests – Side plates ............................................................ 10

3.4 Foldable backrest .................................................................... 10

3.5 Anti-tipping (optional) .............................................................. 10

3.6 Comfort adjustments ............................................................... 10

3.7 Moving to/from your wheelchair .............................................. 12

3.8 Riding ...................................................................................... 12

4 Maintenance ..................................................................................... 13

4.1 Points of maintenance ............................................................. 13

4.2 Maintenance instructions ......................................................... 13

4.3 Troubleshooting ....................................................................... 14

4.4 Expected lifespan .................................................................... 14

4.5 Reuse ...................................................................................... 14

4.6 End of use ............................................................................... 14

5 Technical specifications .................................................................. 15

Trigo S

2021-10

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren wheelchair!

This wheelchair is made by qualified and committed personnel. It is designed and produced

according to high quality standards, guarded by Vermeiren.

Please read this manual carefully; it will help you to get familiar with the operation, capabilities

and limitations of your wheelchair. If you still have questions after reading this manual, do not

hesitate to contact your specialist dealer. He/she will be glad to help you.

Important note

To ensure your safety, and to prolong the lifetime of your product, please take good care of it and

have it checked and serviced on a regular basis.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without any obligation to adapt or replace similar products

previously delivered.

Pictures are used to clarify the instructions in this manual. Details of the depicted product may

deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of the

information in this manual. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

User manual For user and specialist dealer

Installation instructions For specialist dealer

Service manual for wheelchairs For specialist dealer

EC declaration of conformity

Trigo S

2021-10

Your product

3

EN

NL

1 Your product

The Trigo S wheelchair is an active, foldable wheelchair, with one fixed footplate and a wide range

of adjustment options. It is easy to operate by the occupant and can be used indoors as well as

outdoors.

The Trigo S is available in several versions and with the options as shown on our website, see

also §5.

1. Backrest

2. Side plate / armrest

3. Seat

4. Frame

5. Footplate

6. Front wheel

7. Rear wheel

8. Push handle (optional)

9. Footrest

10. Brake

11. Identification plate

5

8

11

2

1

3

7

5

4

2

6

9

10

Trigo S

2021-10

Your product

4

EN

NL

1.1 Accessories

The following accessories are available for Trigo:

• Crutch holder

• Anti-tipping wheel

• Travel castors

• Backrest stabilisation bar

• Pelot – side support left/right

• Off road wheels 24”

• Gel cover push rim

• Spoke protection

• Anterior pelvic support

Trigo S

2021-10

Before use

5

EN

NL

2 Before use

This manual is applicable to the wheelchair Trigo S in all its configurations.

2.1 Intended use

• This wheelchair is suitable for indoor and outdoor use.

• This wheelchair is designed and produced solely to transport/transfer one (1) person with a

maximum weight according to the configuration of the technical specifications in §5. It is not

designed to transport goods or objects, nor for any other use as previously described.

• This wheelchair is meant to be operated by the user sitting in the wheelchair. If push handles

are installed, it can be operated by an attendant as well.

• You should NOT use this wheelchair if you suffer from physical or mental impairments that

may put you, or other people, in danger when riding the wheelchair. For this reason, consult

your doctor first and make sure that your specialist dealer is informed about his advice.

• Only use accessories and spare parts approved by Vermeiren.

• Please read all technical details and limits of your wheelchair in §5.

• The warranty of this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 General safety instructions

Risk of injuries and/or damage

Carefully read and follow the instructions in this manual.

Keep the following general warnings in mind during use:

• Do not use your wheelchair if you are under influence of alcohol, medicines or other

substances that may influence your riding abilities.

• Be aware that some parts of your wheelchair may get very hot or cold due to ambient

temperature, solar radiation or heating devices. Be careful when touching. Wear protective

clothing if the weather is cold. When going outdoors, riding gloves can be used to improve

the grip on the hand rims.

• Alterations or substitutions should not be made to the wheelchair securement points or to

structural and frame parts or components without consulting the wheelchair manufacturer.

Be aware that your wheelchair may interfere with some types of anti-theft systems, depending on

the settings used. This may cause the shop's alarm to go off.

In case a serious incident has occurred involving your product, notify Vermeiren or your specialist

dealer as well as the competent authority in your country.

The symbols in following list are applicable to your wheelchair. Symbols can be found in the

relevant ISO standard (ISO 7000, ISO 7001 and IEC 417).

Maximum weight of the user in kg

Indoor/outdoor use

Maximum safe slope in ° (degrees)

Type designation

CAUTION

Trigo S

2021-10

Before use

6

EN

NL

Risk of entrapment

2.3 Transport

2.3.1 Transport by vehicle, as luggage

1. As user, transfer to a car seat, see §3.7.

2. Fold the wheelchair to its most compact size according to the instructions in § 2.4.

3. Store the wheelchair and its wheels in the luggage compartment or behind the passenger

seat. If luggage and passenger compartments are NOT separated or enclosed, fasten the

wheelchair frame securely to the vehicle. You can use the available safety belt in the vehicle.

Never use the same safety belt for passenger and wheelchair.

2.3.2 Use of the wheelchair as seat in a motor vehicle (only for Trigo with fixed backrest)

Risk of injuries

• For Trigo with foldable/angle adjustable backrest: Do NOT use your wheelchair as

a seat in a vehicle, see the following symbol.

• The wheelchair has passed the crash test of ISO 7176-19: 2008 and, as such, has been

designed and tested for use only as forward-facing seat in a motor vehicle. Ease of access to,

and manoeuvrability in, motor vehicles can be significantly affected by wheelchair size and

turning radius.

• The wheelchair's pelvic belt alone is not suited as an occupant restraint belt.

• Use the wheelchair's pelvic belt and the applicable three-points belt in the vehicle to prevent

head and chest impacts with the vehicle.

• Do not use postural supports to restrain the user in the vehicle unless they are labelled as

being in accordance with the requirements specified in ISO 7176-19:2008.

• Following involvement in any type of vehicle collision, have your wheelchair inspected by the

specialist dealer or manufacturer’s representative before reuse.

The wheelchair is tested using the four-point strap-tie system and a 3-point occupant-restraint

system.

Whenever feasible, use the seat of the vehicle and store the wheelchair in the cargo area.

Steps to secure the wheelchair in a motor vehicle:

1. Check that the vehicle is equipped with a suitable wheelchair tie down and occupant-restraint

system, conform ISO 10542.

2. Check that the components of the wheelchair tie down and occupant restraint system are not

frayed, contaminated, damaged or broken.

3. If equipped with an adjustable seat and/or back tilt, make sure that the wheelchair user is

sitting as upright as possible. If the user's condition prevents this, a risk assessment should

be done to evaluate the user's safety during transit.

4. Remove all mounted accessories such as trays and respiratory equipment, and secure them

in a safe place.

5. Position the wheelchair facing forward in the travelling direction, centrally between the tie-

down rails mounted in the floor of the vehicle.

6. Mount the front securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1). This place is marked on the wheelchair with a

symbol (figure 2).

7. Roll back the wheelchair until the front straps are tight.

8. Apply the wheelchair brake.

9. Mount the back securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1). This place is marked on the wheelchair with a

symbol (figure 2).

WARNING

Trigo S

2021-10

Before use

7

EN

NL

Steps to secure the wheelchair user:

1. Remove both armrests (if possible).

2. If present, attach the wheelchair's pelvic belt.

3. Attach the occupant restraint belts according to the

instructions of the strap-system manufacturer.

4. Wear the pelvic belt low across the front of the pelvis,

so that the angle of the pelvic belt is within the

preferred zone of 30° to 75° to the horizontal, similar

to that shown in the figure.

5. A steeper (greater) angle within the preferred zone is

desirable.

6. Adjust the belt tightly according to the instructions of

the strap-system manufacturer, consistent with the

user's comfort.

7. Ensure that the restraint belt connects in a straight line to the anchor point in the vehicle

and that no bends in the belt are visible, for instance at the axle of the rear wheel.

8. Install the armrests, if desired. make sure that belts are not twisted or held away from the

body by wheelchair components such as armrests or wheels.

9. Position the seatbelt buckle so that the release button will not be contacted by wheelchair

components during a crash.

10. Make sure that the shoulder-belt restraints fit over the shoulders, see figure 4.

Belt restraints must not be held away

from the body by wheelchair

components such as armrests or

wheels.

Belt restraints make full contact with

shoulder, chest and pelvis.

Pelvic belt low on the pelvis near the

thigh-abdominal junction

Figure 3 Improper belt-restraint fit

Figure 4 Proper belt-restraint fit

Figure 2

Figure 1

✓

Trigo S

2021-10

Before use

8

EN

NL

2.4 Folding - unfolding

Risk of injuries and/or damage

• Make sure that your fingers don’t get trapped at the pivot point of the handles and frame cross.

• Always keep the swing range of the footplate in mind to prevent bystanders from being injured

or objects from being damaged.

To fold the wheelchair:

1. Pull the seat cushion and remove it.

2. Depending on type of footplate (8):

• Open footplate: Unlock and turn it up

• Foldable footplate: Pull it up to fold

3. Grab the front and back of the seat (15) in the middle,

and pull to close.

4. Push seat frame tubes (5) together.

5. Remove the rear wheels if necessary, see §2.5.

To unfold the wheelchair:

1. Pull the seat frame tubes (5) outwards, and push the seat

frame down at the left and right side until the seat is flat

and the frame is locked into place.

2. If removed, assemble the rear wheels, see §2.5.

3. Place the seat cushion (4) on the Velcro straps of the

seat. Make sure that the straps of the seat cushion lie

transverse over the straps of the seat.

4. Depending on type of footplate (8):

• Open footplate: Turn it down until it is locked.

• Foldable footplate: Push it down until it is blocked.

2.5 (Dis)Assembling rear wheels

To remove the rear wheels

1. Press and hold button (43) while sliding the wheel axle out of the hole of the frame.

2. Repeat this for the other wheel and place the wheelchair gently on the rear frame tubes.

To install the rear wheels

1. Take one of the rear wheels and lift the wheelchair on one

side.

2. Press and hold button (43) while sliding the wheel into the

axle bushy.

3. Release the button to lock the wheel. Make sure it clicks

into place.

4. Repeat this for the other wheel.

5. Ensure that both wheels are firmly secured.

2.6 Storage

Make sure that your wheelchair is stored in a dry environment to prevent mould from

growing and the upholstery from being damaged, see also chapter 5.

CAUTION

43

8

15

5

Trigo S

2021-10

Using your wheelchair

9

EN

NL

3 Using your wheelchair

Risk of injuries and/or damage

Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or other

moving parts, during use or adjustment.

3.1 Parking brakes

Risk of injuries and/or damage

• Never release both brakes simultaneously.

• Brakes may only be adjusted by your specialist dealer.

• Do not use the parking brakes to slow the wheelchair down during movements.

Push-pull brakes

Releasing brakes (A):

1. With one hand, hold one of the hand rims.

2. Push or pull brake lever (10) of the OTHER wheel.

3. Repeat this for the second wheel and parking brake.

Applying brakes (B):

1. With one hand, hold one of the hand rims.

2. Pull or push brake lever (10) of the OTHER wheel until you feel

a distinctive lock.

3. Repeat this for the second wheel and parking brake.

Sport brakes

The sport brakes are located underneath the seat.

Releasing brakes :

1. With one hand, hold one of the hand rims.

2. Pull the handle of the OTHER wheel BACKWARDS.

3. Repeat this for the second wheel and parking brake.

Applying brakes :

1. With one hand, hold on of the hand rims.

2. Push the brake handle of the OTHER wheel FORWARD until you feel a distinctive lock.

3. Repeat this for the second wheel and parking brake.

CAUTION

The push-pull parking brake can be mounted in two ways

(directions), to be decided upon ordering the wheelchair.

Depending on the chosen direction, the brake needs to be

pushed or pulled for operation.

A

B

10

Trigo S

2021-10

Using your wheelchair

10

EN

NL

3.2 Push handles

Depending on the chosen configurations, your wheelchair can be delivered without push handles,

or it can be provided with normal handles, or foldable handles.

3.3 Armrests – Side plates

Depending on the chosen configurations, your wheelchair can be provided with a range of

different armrests:

• Fixed sideplates without armrests

• Fixed sideplates with armrests

• Foldable tubular armrests

• Removable sideplates

3.4 Foldable backrest

To fold the backrest onto the seat

1. Gently pull the back strap (20). The safety pins of the folding

mechanism (21) are released.

2. Push the backrest down onto the seat.

To pull the backrest up

1. Pull the backrest up until it clicks into position.

2. Make sure that both safety pins are locked in the holes of the

folding mechanism (21).

3. Check by moving the backrest.

3.5 Anti-tipping (optional)

The anti-tipping device prevents your wheelchair from tipping over backwards. When the device

is not needed, it can be swung to the side by pulling the vertical bar (16) down and turning it

towards the front of the chair, until it clicks into place.

To adjust the height of the anti-tipping device according

to the position and size of the rear wheels:

1. Loosen the star knob (17) until the inner tube of

the anti-tipping can be moved in the support.

2. Slide the anti-tipping up/down until the desired

position.

3. Tighten the star knob (17).

The anti-tipping should be approximately 15-20mm

above the ground.

3.6 Comfort adjustments

Risk of injuries and/or damage

• The following comfort adjustments can be done by the attendant or caretaker. All other

adjustments are done by your specialist dealer (see installation instruction).

• Always keep the swing range of the footrest in mind to prevent bystanders from being injured

or objects from being damaged.

• Make sure that your fingers, clothes, buckles won’t get entrapped during adjustment.

CAUTION

20

21

16

17

Trigo S

2021-10

Using your wheelchair

11

EN

NL

3.6.1 Backrest width and support

The backrest of the wheelchair has a suspension system with adjustable Velcro straps, to adjust

the width and flexibility of the backrest.

1. Pull the backrest cushion from the Velcro straps of the

backrest.

2. Loosen the Velcro straps.

3. Pull the respective strap to the desired position. The

tension of the individual belts can be varied and the

desired support of the back can be set.

4. Place the back cushion back over the backrest starting

at the front and ending at the back.

5. Secure the Velcro connections by pressing the cushion

against the backrest with your hand.

6. Make sure that all straps are secured with Velcro.

3.6.2 Backrest height (step adjustment)

1. Remove the back cushion.

2. Push the spring button located on the back of the back frame tube.

3. Move the backrest up/down to the desired height.

4. Make sure that the spring button clicks back in the corresponding hole.

5. Repeat for the other side. Make sure that both sides are set to the same height and that

they are firmly secured.

3.6.3 Push handle height (stepless adjustment)

Fixing lever

1. Turn the push handle lever (40) to loosen it.

2. Move the push handle up/down to the desired height.

3. Secure the handle by tightening the lever(40).

4. Repeat for the second push handle. Make sure that both

handles are set to the same height and that they are firmly

secured.

Fixing knob

1. Turn the push handle knob (30) a few turns anticlockwise.

2. Move the push handle up/down to the desired height.

3. Secure the handle by tightening the knob; turn it clockwise.

4. Repeat for the other side. Make sure that both sides are set to

the same height and that they are firmly secured.

40

30

Trigo S

2021-10

Using your wheelchair

12

EN

NL

3.7 Moving to/from your wheelchair

Risk of injuries and damage

• In case you cannot perform the transfer in a safe manner, ask someone to assist you.

• Do not stand on the footplate during transfer into or out of the wheelchair.

Transfer

1. Position the wheelchair as close as possible to you when sitting in your chair, couch, seat

or bed.

2. Apply both parking brakes to block the movement, see §3.1.

3. If possible, fold the open footplate upwards to prevent standing on it.

4. Transfer to/from the wheelchair using the strength of your arms or with the help of

attendant(s) or lifting equipment.

Sitting in the wheelchair

1. Sit down on the seat with your lower back against the backrest.

2. If applicable, fold the open footplate down and put your feet on the footplate.

3.8 Riding

Risk of injuries and damage

• Before every usage, make sure that:

o parking brakes are working properly.

o tires are in good condition, see §4.

• Prevent your fingers from being caught by the wheel spokes.

• Do not operate the hand rims with wet hands.

• Prevent entrapment of your hands on the hand rims when you pass small passages.

• Do NOT drive on slopes, obstacles, steps or kerbs larger than specified in §5.

• When you stop on a (small) slope, use your brakes.

• Make sure all four wheels touch the ground while riding up or down a slope.

• Take slopes as slow as possible.

• Always stay on the pavement when riding on public roads.

• Pay attention if the road has holes or gaps that may cause entrapment of the wheels.

• Avoid stones and other objects that may block the wheels.

• Make sure that the footplate does not touch ground while taking an obstacle.

• Do not use your wheelchair on an escalator.

• If available, wear your safety belt.

• Always keep the swing range of the footplate in mind to prevent bystanders from being injured

or objects from being damaged.

• If you don’t have enough experience riding your wheelchair, ask assistance of an attendant.

Keep your arms away from the wheels and keep your feet on the footplate.

• Stairs should always be negotiated with the help of two attendants.

• Never try to use stairs that are not appropriate for wheelchairs.

3.8.1 Riding your wheelchair:

1. Release the brakes.

2. Take both hand rims at their highest position.

3. Lean forward and push the hand rims forward until your arms are straight.

4. Move your hands back to the top of the hand rims and repeat the movement.

CAUTION

Trigo S

2021-10

Maintenance

13

EN

NL

4 Maintenance

4.1 Points of maintenance

Risk of injuries and damage

Repairs and replacements may only be undertaken by trained persons and only genuine

replacement parts of Vermeiren should be used.

The service frequency depends on the frequency and intensity of use. Contact your dealer

to agree to a common timetable for inspection/maintenance/repair.

For the maintenance manual, refer to the Vermeiren website: www.vermeiren.com.

Before each use

Inspect the following points:

• All parts: Present and undamaged or unworn.

• All parts: Clean, see § 4.2.2.

• Wheels, backrest, seat, calf rests, arm rests, footplate: Well secured.

• Condition of wheels/tyres, see § 4.2.1;

• Condition of frame parts: No deformation, instability, weakness or loose connections

• Seat, backrest, arm pads, calf pads and head rest (if applied): No excessive wear (like

dented spots, damage or tears).

• Brakes: Undamaged and functioning

Contact your specialist dealer for possible repairs or part replacements.

Yearly or more often

Have your wheelchair inspected and serviced by your specialist dealer, at least once a year, or

more often. The minimum maintenance frequency depends on use and should therefore be

commonly agreed on with your specialist dealer.

4.2 Maintenance instructions

4.2.1 Wheels and tyres

Proper working of the brakes depends on the state of the tyres, and can change due to

wear and contamination (water, oil, mud, …).

Keep your wheels free of wires, hair, sand and fibres.

Check the profile of the tyres. If the tread depth is less than 1 mm, the tyres need to be replaced.

Contact your specialist dealer for this matter.

Inflate each pneumatic tyre to the correct pressure (see pressure indication on the tyres).

4.2.2 Cleaning

Risk of damage by moisture

• Never use a hose or high-pressure cleaner to clean the wheelchair.

Wipe all rigid parts of the wheelchair with a damp cloth (not drenched).

If necessary, use a mild soap, suitable for varnishes and synthetics.

The upholstery can be cleaned with lukewarm water and a mild soap. Do not use abrasive

cleaning agents to clean.

CAUTION

Trigo S

2021-10

Maintenance

14

EN

NL

4.2.3 Disinfection

Risk of damage

• Disinfections may only be undertaken by trained persons. Consult your specialist dealer.

4.3 Troubleshooting

Even if you use your wheelchair properly, a technical problem may occur. If this is the case,

contact your local specialist dealer.

Risk of injuries and damage to the wheelchair

• NEVER attempt to repair the wheelchair yourself.

The following symptoms may indicate a serious problem. Therefore always contact your specialist

dealer if you spot any of the following deviations:

• Strange sound;

• Uneven tread wear on one of the tyres;

• Jerky movements;

• Wheelchair deflects to one side;

• Damaged or broken wheel assemblies.

4.4 Expected lifespan

The average lifespan of your wheelchair is 5 years. Depending on the frequency of use, driving

circumstances and maintenance, the lifespan of your wheelchair will increase or decrease.

4.5 Reuse

Before reuse by another person, have the wheelchair disinfected, inspected and serviced

according to the instructions in §4.1 and §4.2.

4.6 End of use

At end of life, you need to dispose your wheelchair according to the local environmental

legislation. The best way to do so, is to disassemble the wheelchair to facilitate the transport of

recyclable parts.

CAUTION

WARNING

Trigo S

2021-10

Technical specifications

15

EN

NL

5 Technical specifications

The technical details below are only valid for this wheelchair, at standard settings and optimal

ambient conditions. Take these details into account during use.

The values are no longer applicable if your wheelchair has been modified, damaged or suffers

from severe wear.

Table 1: Technical specifications

Brand

VERMEIREN

Type

Wheelchair

Model

Trigo S

Description

Specifications

Max. weight of user

For seat width up to 360 mm with single cross:

70 kg

For seat width from 380 up to 460 mm with 1.5 cross:

130 kg

For seat width from 480 up to 500 mm with double cross:

130 kg

Static stability

5°

Dimensions

Min.

Max.

Overall length

676 mm

1046 mm

Dismantled length (wheels dismantled)

650 mm

855 mm

Dismantled width (wheels dismantled)

386 mm

586 mm

Folded height (depending on wheel

diameters)

457 mm

660 mm

Wheelchair height

(depends on type of rear wheel,

adjustment, push handle or backrest

height)

457 mm

945 mm

Folded height without wheels

Max. 428 mm

Seat width

300 mm

500 mm

Overall width in mm

(24” rear wheels, 0° camber):

460 mm

660 mm

Wheelchair length

(depending on seat depth, type of rear

wheel, type of footplate, adjustment)

676 mm

1046 mm

Canvas depth – Seat depth

320 mm

500 mm

Backrest height, adjustable

Non-foldable BR

Foldable BR

(in steps of 25 mm)

250 – 300 mm

300 – 350 mm

350 – 400 mm

400 – 450 mm

450 – 500 mm

Backrest height, fixed, foldable

(in steps of 20 mm)

250 – 510 mm

Seat height at front seat-edge of seat, in

relation to front wheels 3" front wheel

4" front wheel

5" front wheel

6" front wheel

(in steps of 10 mm)

380 – 470 mm

390 – 490 mm

410 – 500 mm

430 – 510 mm

Trigo S

2021-10

Technical specifications

16

EN

NL

Seat height at rear seat-edge, depending

on rear wheel 18" rear wheel

20” rear wheel

22" rear wheel

24" rear wheel

26" rear wheel

(in steps of 10 mm)

315 – 415 mm

335 – 435 mm

355 – 465 mm

385 – 495 mm

405 – 515 mm

Distance between side plate/mudguard and

seat

0 mm

Distance between footplate and seat

220 – 500 mm (in steps of 20 mm)

Footrest length, adjustable

220 mm

480 mm

Seat plane angle adjustable

20°

Angle between seat and footrest

Fixed, 70° or 80°

Angle foot plate and footrest

Infinite (stepless)

Weights

Total mass

12 kg

Mass of heaviest part (without seat and

back cushion, wheels)

8.2 kg

Masses of removable parts: Wheel 24”

Backrest cushion

Seat cushion

Push handle (adjustable)

3.1 kg

0.4 kg

Wheels

Camber angle of rear wheels default

setting, adjustable

0°

2°

4°

6°

Front wheels

3" - 4" - 5" - 6”

Rear wheels

18” – 20” - 22" - 24" - 26”

Hand rim diameter

400 mm – 440 mm – 500 mm – 535 mm – 600 mm

Tyre pressure, rear wheels

2.5 - 10 bar

Environment

Strength tests according to

ISO 7176-8

Ignitability of upholstery according to

EN 1021-2

Overall rating of belt-restraint

accommodation

C

Storage and use temperature

+5 °C ~ +41 °C

Storage and use humidity

30% ~ 70%

We reserve the right to introduce technical changes.

Measurement tolerance ± 15 mm /1,5 kg / 1,5°.

La page charge ...

Vermeiren Trigo S Manuel utilisateur

Vermeiren Trigo S Manuel utilisateur

dans d''autres langues

Documents connexes