Samoa 383406 Instructions Manual

Taper
Instructions Manual

Ce manuel convient également à

1
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_07_03-12:30
Part No. / Cód. / Réf. / Art. Nr.:
383 405
383 406
383 407
U·LINK GUN 2
PISTOLA U·LINK 14
PISTOLET U·LINK 26
PISTOLE U·LINK 38
EN
ES
FR
DE
Parts and technical service guide
Guía de servicio técnico y recambio
Guide d’instructions et pièces de rechange
Bedienungsanleitung und Ersatzteilliste
2896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
WARNINGS AND CAUTIONS
EQUIPMENT MISUSE
This unit is intented for professional use. Read all the instructions in this manual prior to use.
Only use the unit for the purposes for which it is intended.
This unit has not been approved fro use in commercial transactions.
Do not tamper the unit.
CHEMICAL COMPATIBILITIES
Use the equipment only with compatible fluids and in the specified operating range. Please refer to
the technical specifications section.
SAFETY MEASURES
It is mandatory to respect the batteries polarity and follow their placement order as indicated in the
batteries cover.
If a leakage is detected in the batteries protect your eyes and skin. Cover the batteries housing with a cloth
before opening it to avoid that acid get sprayed onto your skin or eyes. If acid should spray into your eyes,
rinse immediately with clear water for several minutes. Consult a doctor immediately afterwards.
• Do not mix different battery brands or new batteries with old ones.
INFORMATION ABOUT WASTES
The previous symbol indicates that in agreement with local laws, your product and/or your battery should be
dispose of independently of your home wastes. When this product reaches the final of its useful life, you will
need to take it to a collection point designated by the local authorities. The separate collection and the
product or battery recycling will help to protect the natural resources and guarantee its recycling in such a
way that protects the health of the people and environment.
3
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
Mount the non-drip nozzle with the ½” bonded seal
provided (A). Tighten the nozzle nut (Aa) firmly to prevent
leakage. If using a rigid nozzle, first tighten the nut (Ab),
place in proper position the nozzle tube (B) and then tighten
the nut (C) to secure it.
Before connecting the hose to the gun, you must assemble
the swivel cover (D) into the hose (E). This cover is compatible
with ½” hoses. Depending on the hose end type (F) it may
be necessary to open the groove at the swivel cover end to
allow it to enter through the hose fitting.
To connect the hose, hold the hose end (F) stationary
while turning the swivel end (G) until the desired tightness
is achieved.
INSTALLATION
BATTERIES INSTALLATION AND REPLACEMENT
This equipment employs 4 AA 1.5 V alkaline batteries for its
operation. The gun is supplied without these batteries
installed, follow the procedure described below for
installation or replacement:
1. Remove the rubber cover (A) and then loosen the
screws (B). Remove the battery housing cover (C).
A
C
B
Aa
Ab
B
C
A
A
F
D
G
E
4896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
BATTERIES INSTALLATION AND REPLACEMENT
2. Install the supplied batteries (D) or equivalent batteries
(see technical specifications) according to the polarity
indicated in the battery compartment (E).
3. Place again the cover (C) and tighten the screws (B).
4. Finally, mount the rubber protector (A).
The gun automatically switches off after 30 seconds of
inactivity to save energy. To turn the display back on, press
any of the UP/DOWN keys. Once the display is activated, the
name of the equipment is briefly displayed along with the
OVERVIEW
DE E
BUTTON FUNCTION
UP/DOWN
Switching on, scrolling through
menus, changing values
LEFT/RIGHT Screen scrolling
Cancel, go back
Confirmation / enter button
software version installed. Next, the configured gun operating
mode is displayed and after a moment the screen where the
user can be entered is displayed. The following section
describes in detail the gun operating modes.
001
PRESELECTION MODE
TEST
001
ULink+
NEX U
FW 1.10
001
ENTER USER PIN
0
?
5
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
OPERATION
The gun has the following dispensing modes:
STANDARD MODE, PRESET MODE and REMOTE MODE.
STANDARD MODE: the user can freely choose the
quantity to be dispensed without the need to validate
the work order, but it is necessary to enter it.
PRESET MODE: a work order must be selected in the
system in order to proceed to dispensing.
By default, the selected mode is STANDARD MODE.
However, we can modify this operation from the U-track in
NOTE: Before starting the dispensing process, make sure
that the trigger is not pulled.
Check that the STANDARD mode appears on the display
once the gun is started.
To dispense fluid, follow the procedure below:
1. From the user input screen, enter the user code using the
left/right buttons to change position and the up/down
buttons to select the character corresponding to the
code. The user code can contain up to 50 possible
characters, 4 will be displayed on the screen and you can
scroll to the rest using the left/right buttons.
If you wish to reset the user entered and start the
process again, press the CANCEL button. To confirm
the user, press the ENTER button and it will be sent to
the U-track for validation.
If this user does not exist in the U-track database, you
will receive an error message and you will be allowed to
re-enter another user.
2. Once the user has been validated, the next step is to
enter the JOB (work order), the buttons operation is
exactly the same as in the previous point. In STANDARD
mode, the JOB entered can be any JOB, as it does not
have to be validated by the U-track.
To reset the JOB entered and start the process again press
the CANCEL button.
To confirm the JOB entered, press the ENTER button.
STANDARD MODE OPERATION 001
STANDARD MODE
PRODUCT
001
SELECT JOB
1
wo ?
001
ERROR USER!
ERROR
PRODUCT
001
ENTER USER PIN ?
1
the NEXU pre-selection gun configuration section and
choose between the three available modes.
REMOTE MODE: the user launches a transaction from the
U·Track and when the gun wakes up this transaction will
appear on the screen for approval or cancellation.
6896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
OPERATION
3. The last step consists of entering the desired quantity,
using the UP/DOWN buttons to modify the quantity and
the LEFT/RIGHT buttons to scroll through each digit.
It must be taken into account that the maximum quantity
entered cannot exceed the “maximum quantity”
parameter that has been established from the U-track.
To reset the quantity entered and start the process again
press the CANCEL button.
To confirm the quantity entered, press the ENTER button
and the transaction initiation request will be sent to the
U-track, so that it can accept it and start the dispensing
process.
4. For safety reasons, before starting the transaction, an
information message appears indicating that the trigger
must be released; it will be necessary to confirm by
pressing the ENTER button.
5. After pressing the ENTER button we will start dispensing
by pulling the trigger.
6. During dispensing, you can manually operate the trigger
(A) or you can leave the trigger fixed by means of the
locking button (B). In both cases, the valve will
automatically shut off the dispensing when the preset
quantity is reached.
To lock the trigger in the open position: pull the trigger,
move the locking button forward with your index finger
and, holding it in this position, let the trigger down.
Once the trigger is locked, you can stop pushing the
button.
7. If you wish to stop the dispense before it reaches the
pre-selected amount, press the CANCEL button. The
display will show “CANCEL?” on the bottom line waiting
for confirmation by pressing the ENTER button, in which
case the transaction closure will be sent to the U-track. If
you do not wish to stop the transaction press CANCEL
again to return to the previous state.
001
001
SELECT QUANTITY
RELEASE TRIGGER, OK?
0 0 0.0
PRODUCT
PRODUCT
001
3.00 L
0.02
PRODUCT
001
CANCELLED
0.00
PRODUCT
001
CANCEL?
0.16
PRODUCT
B
A
7
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
OPERATION
8. If dispensing is not interrupted, when the requested
amount is reached, the valve closes automatically and the
transaction end message is sent to the U-track, returning to
the initial state to enter the user again.
1. In the “ENTER USER PIN” screen, we enter the user by
using the UP/DOWN buttons to select the appropriate
digit or letter and the LEFT/RIGHT buttons to move
through the 50 possible characters that our USER PIN
could have.
2. Once the user has been validated, the U-track receives
the work orders associated with the product linked
to the gun.
To reset the user entered and start the process again,
press the CANCEL button.
To confirm the user press the ENTER button, which will
be sent to the U-track for validation.
If the user does not exist in the U-track database, we will
receive an error message and we will be allowed to enter
another user again.
Use the UP/DOWN buttons to move through the
available orders. If we press the CANCEL button, we will
go back to the previous step to be able to modify the
user. Once the work order has been selected, we will
confirm it by pressing the ENTER button.
To start the transaction press the ENTER button.
3. The quantity associated with the work order is then
displayed on the screen and confirmation for the
transaction start is requested.
Before dispensing, make sure that the gun is in this mode:
9. Finally, release the trigger if it was manually operated or
press it upwards and then let it return to its rest position if
you had used the locking button.
PRESET MODE OPERATION 001
STANDARD MODE
TEST
001
ENTER USER PIN ?
1
001
ERROR USER!
ERROR
PRODUCT
001
OK?
2.55
TEST
001
SELECT JOB
TEST
wo ?
1 - 1
T1
8896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
OPERATION
4. During dispensing, you can either operate the trigger
manually or you can leave the trigger fixed by means of the
locking button in the same way as described in the
standard dispensing mode. In both cases, the valve will
automatically cut off the dispensing when the preset
quantity is reached.
5. If you wish to stop the dispense before it reaches the pre-
selected amount, press the CANCEL button. The display
will show “CANCEL?” on the bottom line waiting for
confirmation by pressing the ENTER button, in which case
the transaction closure will be sent to the U-track. If you do
not wish to stop the transaction press CANCEL again to
return to the previous state.
6. If dispensing is not interrupted, when the requested
amount is reached, the valve closes automatically and the
transaction end message is sent to the U-track, returning to
the initial state to enter the user again.
7. Finally, release the trigger if it was manually operated or
press it upwards and then let it return to its rest position if
you had used the locking button.
1. As shown in the image above, if a transaction has been
launched from the UTRACK when the gun wakes up, the
amount associated with that transaction will be displayed
on the screen and confirmation is required to start the
transaction. To start the transaction press the ENTER
button. In case you want to cancel the transaction press
the CANCEL button.
In this mode, the user launches a transaction from the
UTRACK and when the gun wakes up this transaction will
appear on the screen for approval or cancellation.
DISPENSING THROUGH REMOTE MODE
2. For safety reasons, as in the rest of the modes, before
starting the transaction, an informative message will
appear indicating that the trigger must be released; once
this action is done it is necessary to press the ENTER
button to transaction start. At this point it is also
possible to cancel the transaction start by pressing the
CANCEL button.
3. After pressing the ENTER button, we can start the
dispensing by pressing the trigger.
4. During dispensing, you can manually operate the trigger
(1) or you can leave the trigger fixed by means of the
lock button (2). In both cases, the valve will automatically
shut off the dispense when the preset amount is reached.
5. If at any time, you want to cancel or stop the transaction,
press the CANCEL button. The display will show
“CANCEL?” at the bottom of the screen and we will have
to confirm the process by pressing the ENTER button. At
this point the transaction will be closed and sent to the
UTRACK. If you do not want to stop the transaction, press
the CANCEL button again to return to the previous state.
6. If the transaction is not interrupted, when the dispensed
amount reaches the target amount, the valve will close
automatically and the transaction end message will be
sent to the UTRACK, showing on the screen that there is
no new transaction in progress (“NO TR. IN PROGRESS”)
and shutting down to save battery power.
001
CANCELLED
0.00
PRODUCT
001
CANCEL?
0.16
PRODUCT
9
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
This gun allows the following configurations:
Simultaneously press the ENTER and CANCEL buttons until
after about 3 seconds the setup menu access screen is
displayed and after a moment displays the setup options:
Note: if we turn on the gun with the ENTER and CANCEL
buttons pressed simultaneously, we will also access the local
configuration menu.
Pressing the UP/DOWN buttons allows navigation through
the various menu functions. To enter any of the submenus
press the ENTER button when the desired menu is selected.
LOCAL SETUP: allows setting local parameters
such as Hose ID.
RF TEST: allows the signal level to be checked.
CALIBRATE.
LOCAL CONFIGURATION MENU
MENU NAVIGATION
EDIT PARAMS: allows you to edit operating
parameters such as calibration K-factor and
display orientation.
WHEN THE GUN IS STARTED, IT ATTEMPTS TO CONNECT
TO THE U·net PRO TO COMMUNICATE. IF THIS
CONNECTION IS UNSUCCESSFUL, THE GUN ENTERS
WHAT WE CALL EMERGENCY MODE.IN THIS MODE IT IS
NECESSARY TO ENTER AN EMERGENCY CODE THAT WILL
EMERGENCY MODE
ALLOW US TO DISPENSE.THESE QUANTITIES ARE STORED
AND SENT AS “RACLEE” IN THE FIRST NORMAL OPERATING
TRANSACTION AFTER ENTERING EMERGENCY MODE.*IF
NEEDED, CONTACT SAMOA TO OBTAIN THIS CODE.
OPERATION
001
SETUP
PRODUCT - SETUP MENU -
- LOCAL SETUP.
- RF TEST
- CALIBRATE
- EDIT PARAMS.
- EXIT
10 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
LOCAL CONFIGURATION MENU
LOCAL SETUP SUBMENU
CALIBRATE SUBMENU
RF TEST SUBMENU
This menu allows us to modify the gun identifier. These are
numerical values that must coincide with the value
configured in the U-track. Modify their value using the UP/
DOWN buttons.
This menu allows you to calibrate the gun when it has a
calibrated container. To do this, we must dispense into a
measuring cup according to the following procedure:
Make sure that the trigger is not pulled and press the
ENTER button below.
To ensure that you can make adjustments while dispensing,
a quantity equal to twice the value entered is preset
for safety.
1. Once inside the menu, enter the amount to be
dispensed (typically the amount indicated on the
container) by selecting the desired digit using the
LEFT/RIGHT buttons and changing its value using the
UP/RIGHT buttons.
2. Once the amount is set, press ENTER to confirm and
you will be prompted to confirm that you are not
pressing the trigger.
3. The pre-selected quantity is displayed and you can start
dispensing fluid into the container.
This menu allows us to obtain the RSSI transmission signal
value (in dBm) and to display it graphically in order to get
an idea of how good or bad is our signal.
- LOCAL SETUP -
HOSE NB.:
?[ 1]
- RF TEST -
RSSI: -52 dBm
SELECT QUANTITY
SELECT QUANTITY
0
0
0
0
0
2
.
.
0
0
CALIB.
CALIB.
RELEASE TRIGGER, OK?
CALIB.
001
4.00 L
0.00
CALIB.
11
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
4. Press the CANCEL button and you will be asked if you
wish to cancel to finish dispensing. If we have finished
we will confirm by pressing the ENTER button. If, on the
contrary, we want to continue dispensing, we will press
the CANCEL button.
5. The dispensed quantity is displayed and after 5 seconds
the message “QTE REAL?” is shown on the display.
6. Once this amount has been set, press the ENTER button
to confirm and the gun automatically displays the
newly calculated calibration factor:
We must indicate the quantity actually dispensed, which will
be the quantity registered by the calibrated container. The
UP/DOWN buttons are used to modify the digit value and
the LEFT/RIGHT arrows are used to change the digit.
CONFIGURATION MENU
When you have dispensed the target amount into the
calibrated container, release the trigger to stop the
fluid supply.
001
4.00 L
2.05
CALIB.
001
001001
001
CANCELLED
QTE REAL?QTE REAL?
FACTOR K
2.05
2.002.05
1025
CALIB.
CALIB.CALIB.
CALIB.
001
CANCEL?
2.05
CALIB.
12 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
CONFIGURATION MENU
EDIT PARAMS SUBMENU
This menu allows us to edit the following
operating parameters:
You can enter an already known calibration factor or you
can calculate it manually according to the
following formula:
If you do not wish to change this factor, press ENTER to
proceed to the next parameter.
Calibration factor = x 1000
1. Calibration factor (K-factor): allows the calibration
factor to be changed manually without performing the
vessel calibration process. Use the UP/DOWN buttons
to change it and press the ENTER button to confirm.
2. If you do not wish to change this factor, press ENTER to
proceed to the next parameter.
Display orientation: This menu allows you to change
the direction of the display (normal or inverted), so that
the gun can be adapted to the specific location and the
way it is used. Use the UP/DOWN arrows to select the
desired screen direction and press the ENTER button to
confirm and exit the menu.
quantity indicated on screen
actual quantity dispensed
STRAINER MAINTENANCE
WARNING: Release all pressure within the system
and disconnect the air supply to the pump prior to
performing strainer replacement. Discharge pressure
The gun can be provided with a strainer (optional). To
inspect strainer or make replacement read the
following procedure:
Remove the swivel cover (A) (optional) and loosen the
hose nut (B).
Remove the o-ring (C) fixing the filter (D) and then filter.
Check the filter and clean it or replace as necessary.
Place again the filter with the o-ring and install the hose
with the swivel cover (optional).
!
D
A
C
B
operating the gun into an appropiate container and open
any bleeder-type air valves and fluid drain valver in the
system if necessary.
FACTOR K
1000
- EDIT PARAMS. -
SCREEN
NORMAL
- EDIT PARAMS. -
SCREEN
INVERT
- EDIT PARAMS. -
13
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
TECHNICAL SPECIFICATIONS
Thread port ½” BSP / ½” NPT
Wetted parts materials Acetal, stainless steel, NBR, aluminum, brass, zinc plated steel
Meter type Oval gear
Flowrate 1-30 l/min (0.25 - 7.5 US gal/min)
Maximum pressure 1 - 100 bar (14 - 1450 psi)
Temperature range -10 a 50 ºC (14 a 122 ºF)
Accuracy (oil) ±0,5 %
Accuracy (coolant solutions) ±1 %
Viscosity range Up to 2000 mPa.s
Display Graphic
Units Litres, galons, quarts, pints
Batteries 4 x AA 1.5V
Weight (with nozzle and batteries) 2.1 kg (4.6 lb)
Dimensions (without nozzle tube) 297 x 89 x 155 mm (11.7” x 3.5” x 6.1”) (length x width x height)
SPARE PARTS
4
5
3
1
2
TROUBLESHOOTING GUIDE
Problem Posible cause Solution
Screen does not turn on.
Discharged batteries. Replace batteries.
Stand-by mode. Press UP/DOWN button.
Loose batteries cover. Tighten battery cover screws.
Fluid not being dispensed. A work order is not validated. See “Operation” section.
The gun is not supplying fluid and
a work order has been validated.
You have activated the command with
the trigger held down.
Release the trigger, cancel dispensing
and re-enter the order.
Accuracy error.
Very high or low flowrates used. Calibrate.
Very high or low (water based fluid)
fluid viscosity. Calibrate.
Low flowrate. Strainer damaged or dirty. Replace or clean strainer.
Low pump pressure. Increase pump air pressure.
Dispensed quantity excedes
preset value. Very high flowrate. Adjust valve anticipation closing factor.
Pos. Code Description
1 738904 Electronic module
2 369634 Oval gears kit
3 369639 Valve sealing kit
4
369228.010
(383407)
Flexible 90º outlet with
quarter turn opening
non-drip tip (BSP)
369233.000
(383407)
Formable outlet with
quarter turn opening
non-drip tip (NPT)
5
369232.010
(383406)
Rigid outlet with quarter turn
opening non-drip tip (BSP)
369231.000
(383406)
Rigid outlet with quarter turn
opening non-drip tip (NPT)
14 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_07_03-12:30
ES
ADVERTENCIAS Y PRECAUCIONES
USO INDEBIDO DEL EQUIPO
Este equipo está destinado a uso profesional. Lea todas las instrucciones de este manual antes de su uso.
Use el equipo sólo para los fines a los que está destinado.Esta unidad no ha sido aprobada para su uso
en transacciones comerciales.
No modifique el equipo.
COMPATIBILIDADES QUÍMICAS
Use el equipo sólo con fluidos compatibles y en el rango de funcionamiento especificado (consultar
apartado de especificaciones técnicas).
MEDIDAS DE SEGURIDAD
Es obligatorio respetar la polaridad de las baterías y seguir el orden de colocación indicado en el
alojamiento.
Si se produce una fuga en las pilas, protéjase los ojos. Abra el compartimento de las pilas después de
haberla cubierto con un paño para evitar cualquier salpicadura.
No mezcle pilas de marcas diferentes o pilas nuevas con pilas utilizadas.
INFORMACIÓN SOBRE DESECHO DE RESIDUOS
El símbolo anterior indica que, de acuerdo con las normativas locales, su producto y/o su batería deberán
desecharse de manera independiente de los residuos domésticos. Cuando este producto alcance el final de
su vida útil, deberá llevarlo a un punto de recogida designado por las autoridades locales. La recogida
separada y el reciclaje del producto o su batería en el momento de su desecho ayudarán a proteger los
recursos naturales y a garantizar su reciclaje de forma que proteja la salud de las personas y el medio ambiente.
15
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
ES
Monte la extensión antigoteo con la junta
metaloplástica (A) de ½” proporcionada. Apriete
firmemente la tuerca (Aa) de la extensión para evitar
fugas. En caso de emplear una extensión rígida, apriete en
primer lugar la tuerca (Ab), oriente correctamente el tubo
de la extensión (B) y a continuación apriete la tuerca (C)
para dejarla fija.
INSTALACIÓN
Antes de conectar la manguera a la pistola debe introducir
el protector de rótula (D) en la manguera (E). Este
protector es compatible con mangueras de ½”. En función
del tipo de terminal (F) de la manguera puede ser
necesario abrir la ranura del extremo del protector para
permitir su entrada por el racor (G) de la misma.
Para conectar la manguera mantenga fijo el terminal de la
manguera (F) mientras hace girar el extremo giratorio (G)
de la rótula hasta lograr el apriete deseado.
MONTAJE Y SUSTITUCIÓN DE LAS BATERÍAS
Este equipo emplea para su funcionamiento 4 pilas alcalinas
tamaño AA de 1.5 V. La pistola se suministra sin las pilas
montadas, siga el siguiente procedimiento para su
instalación o sustitución:
1. Retire el protector de goma (A) y a continuación afloje
los tornillos (B) y retire la tapa del compartimento de
baterías (C).
A
C
B
Aa
Ab
B
C
A
A
F
D
G
E
16 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_07_03-12:30
ES
MONTAJE Y SUSTITUCIÓN DE LAS BATERÍAS
2. Instale las pilas suministradas (D) o unas equivalentes
(ver especificaciones técnicas) respetando la polaridad
indicada en el compartimento de pilas (E).
3. Vuelva a poner la tapa (C) y apriete los tornillos (B).
4. Por último, monte el protector de goma (A).
La pistola se apaga automáticamente trascurridos 30
segundos de inactividad para ahorrar energía. Para encender
la pantalla de nuevo pulse cualquiera de las teclas
ARRIBA/ABAJO. Una vez activada la pantalla, se muestra
durante un instante el nombre del equipo junto con la
INTERFAZ
BOTÓN FUNCIÓN
ARRIBA/ABAJO
Encendido,
desplazamiento por menús,
modificación de valores
IZQUIERDA/DERECHA Desplazamiento por pantalla
Cancelar, volver atrás
Botón de confirmación / enter
versión de software instalada. A continuación, se muestra el
modo de funcionamiento de la pistola configurado y
transcurrido un instante se muestra la pantalla donde se
puede introducir el usuario. En el siguiente apartado se
describe en detalle los modos de funcionamiento de
la pistola.
001
PRESELECTION MODE
TEST
001
ULink+
NEX U
FW 1.10
001
ENTER USER PIN
0
?
DE E
17
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
ES
DISPENSADO
La pistola posee los siguientes modos de dispensado:
MODO STANDARD, MODO PRESET y MODO REMOTO.
MODO STANDARD: el usuario puede elegir libremente
la cantidad a dispensar sin necesidad de validar la orden
de trabajo, pero sí es necesario introducirla.
MODO PRESET: se debe seleccionar una orden de
trabajo en el sistema para poder proceder al dispensado
MODO REMOTO: el usuario lanza una transacción
desde el U·Track y, cuando despierte la pistola, esta
transacción aparecerá en la pantalla para su aprobación
o cancelación.
NOTA: Antes de comenzar el proceso de dispensado,
asegúrese de que el gatillo no está accionado.
Verifique que al arrancar la pistola se visualiza el
modo STANDARD.
Para realizar el dispensado de fluido siga el siguiente
procedimiento:
1. Desde la pantalla de introducción de usuario, introducir
el código de usuario utilizando para ello los botones
IZQUIERDA/DERECHA para cambiar de posición y los
botones ARRIBA/ABAJO para seleccionar el carácter
correspondiente al código. El código de usuario puede
contener hasta 50 posibles caracteres, por pantalla se
visualizarán 4 y podrá desplazarse al resto mediante los
botones IZQUIERDA/DERECHA.
Si se desea resetear el usuario introducido y comenzar
de nuevo el proceso, pulsar el botón CANCELAR. Para
confirmar el usuario pulsar el botón ENTER y se enviará
al U·track para su validación.
En caso de no existir dicho usuario en la base de datos
del U·track, se recibirá un mensaje de error y se nos
permitirá volver a introducir otro usuario.
2. Una vez validado el usuario, el siguiente paso consiste en
introducir la JOB (orden de trabajo).
El funcionamiento de los botones es exactamente igual
que en el punto anterior. En el modo estándar la JOB
introducida podrá ser cualquiera, ya que no debe ser
validada por el U·track.
Si una vez introducida la JOB queremos resetearla y
volver a realizar el proceso, pulsaremos el botón
CANCELAR.
Para confirmar la JOB introducida pulsar el botón ENTER.
DISPENSADO MEDIANTE MODO STANDARD
001
STANDARD MODE
PRODUCT
001
SELECT JOB
1
wo ?
001
ERROR USER!
ERROR
PRODUCT
001
ENTER USER PIN ?
1
Por defecto, el modo seleccionado es el modo STANDARD
MODE. No obstante, podemos modificar este
funcionamiento desde el U·track en el apartado de
configuración de la pistola de preselección NEXU y elegir
entre los tres modos disponibles.
18 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_07_03-12:30
ES
DISPENSADO
3. El último paso consiste en introducir la cantidad deseada,
utilizando los botones ARRIBA/ABAJO para modificar la
cantidad y los botones IZQUIERDA/DERECHA para
desplazarnos por cada dígito.
Hay que tener en cuenta que la cantidad máxima
introducida no podrá sobrepasar al parámetro “cantidad
máxima” que se ha establecido desde el U·track.
Si una vez introducida la cantidad queremos resetearla
y volver a realizar el proceso, pulsaremos el
botón CANCELAR.
Si queremos confirmar la cantidad introducida pulsamos
el botón ENTER y se enviará al U·track la solicitud de
inicio de transacción, para que esta la acepte y
comience el dispensado.
4. Por seguridad, antes de arrancar la transacción aparece
un mensaje informativo indicando que el gatillo debe
estar liberado, será necesario confirmar pulsando el
botón ENTER.
5. Tras pulsar el botón ENTER comenzaremos a dispensar
accionado el gatillo.
6. Durante el dispensado, puede accionar manualmente el
gatillo (A) o puede dejar el gatillo fijo mediante el botón
de bloqueo (B). En ambos casos, la válvula cortará
automáticamente el suministro cuando se alcance la
cantidad preseleccionada.
Para bloquear el gatillo en posición abierta: accionar el
gatillo, desplazar el botón de bloqueo con su dedo índice
hacia adelante y manteniéndolo en esa posición deje
descender el gatillo. Una vez que el gatillo queda fijo
puede dejar de empujar el botón.
7. Si desea detener el dispensado antes de que alcance la
cantidad preseleccionada, pulse el botón CANCELAR. La
pantalla mostrará “CANCEL?“ en la línea inferior
esperando que se confirme pulsando el botón ENTER, en
cuyo caso se enviará el cierre de transacción al U·track. Si
no desea detener la transacción pulse de nuevo
CANCELAR para volver al estado anterior.
001
001
SELECT QUANTITY
RELEASE TRIGGER, OK?
0 0 0.0
PRODUCT
PRODUCT
001
3.00 L
0.02
PRODUCT
001
CANCELLED
0.00
PRODUCT
001
CANCEL?
0.16
PRODUCT
B
A
19
R. 07/23 896 853
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
EN
2023_07_03-12:30
ES
DISPENSADO
8. Si no se interrumpe el dispensado, cuando se alcanza la
cantidad solicitada la válvula cierra automáticamente y se
envía el mensaje de final de transacción al U·track,
volviendo al estado inicial para introducir el usuario
nuevamente.
1. En la pantalla “ENTER USER PIN”, introducimos el
usuario utilizando para ello los botones ARRIBA/ABAJO
para elegir el digito o letra adecuada y los botones
IZQUIERDA/DERECHA para movernos a lo largo de los
50 posibles caracteres que podría llegar a tener
nuestro USUARIO.
2. Una vez validado el usuario, desde el U·track se reciben
las órdenes de trabajo asociadas al producto vinculado a
la pistola.
Si deseamos resetear el usuario introducido y comenzar
de nuevo el proceso, pulsamos el botón CANCELAR.
Para confirmar el usuario pulsaremos el botón ENTER,
enviándose este al U·track para su validación.
En caso de no existir dicho usuario en la base de datos
del U·track, recibiremos un mensaje de error y se nos
permitirá volver a introducir otro usuario.
Mediante los botones ARRIBA/ABAJO nos moveremos a
través de las órdenes disponibles. Si pulsamos el botón
CANCELAR, volveremos al paso anterior para poder
modificar el usuario.
Una vez seleccionada la orden de trabajo la confirmaremos
pulsando el botón ENTER.
Para iniciar la transacción pulsar el botón ENTER.
3. A continuación se muestra por pantalla la cantidad
asociada a dicha orden de trabajo y se solicta la
confirmación de inicio de la transacción.
Antes de proceder al dispensado asegurarse de que la pistola
se encuentra en este modo:
9. Finalmente, suelte el gatillo si lo estaba accionado de
manera manual o presiónelo hacia arriba y después déjelo
volver a su posición de reposo si había empleado el botón
de bloqueo.
DISPENSADO MEDIANTE MODO PRESET 001
STANDARD MODE
TEST
001
ENTER USER PIN ?
1
001
ERROR USER!
ERROR
PRODUCT
001
OK?
2.55
TEST
001
SELECT JOB
TEST
wo ?
1 - 1
T1
20 896 853 R. 07/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_07_03-12:30
ES
DISPENSADO
4. Durante el dispensado, puede accionar manualmente el
gatillo o puede dejar el gatillo fijo mediante el botón de
bloqueo de idéntica forma a la descrita en el modo
estándar de dispensado. En ambos casos, la válvula cortará
automáticamente el suministro cuando se alcance la
cantidad preseleccionada.
5. Si desea detener el dispensado antes de que alcance la
cantidad preseleccionada, pulse el botón CANCELAR. La
pantalla mostrará “CANCEL?“ en la línea inferior esperando
que se confirme pulsando el botón ENTER, en cuyo caso se
enviará el cierre de transacción al U·track. Si no desea
detener la transacción pulse de nuevo CANCELAR para
volver al estado anterior.
6. Si no se interrumpe el dispensado, cuando se alcanza la
cantidad solicitada la válvula cierra automáticamente y se
envía el mensaje de final de transacción al U·track, volviendo
al estado inicial para introducir el usuario nuevamente.
7. Finalmente, suelte el gatillo si lo estaba accionado de manera
manual o presiónelo hacia arriba y después déjelo volver a su
posición de reposo si había empleado el botón de bloqueo.
1. Como vemos en la imagen superior, si se ha lanzado una
transacción desde el UTRACK al despertar la pistola, la
cantidad asociada a dicha transacción se mostrará en la
pantalla y es necesaria la confirmación para empezar la
transacción. Para empezar la transacción presiona el
botón ENTER. En caso de querer cancelar la transacción
pulsa el botón CANCEL.
En este modo, el usuario lanza una transacción desde el
UTRACK y, cuando despierte la pistola, esta transacción
aparecerá en la pantalla para su aprobación o cancelación.
DISPENSADO MEDIANTE MODO REMOTO
2. Por motivos de seguridad, al igual que en el resto de los
modos, antes de empezar la transacción, aparecerá un
mensaje informativo indicando que el gatillo debe ser
liberado; una vez realizada esta acción es necesario
presionar el botón ENTER para comenzar la transacción.
En este punto también es posible cancelar el inicio de
transacción pulsando el botón CANCEL.
3. Después de presionar el botón ENTER, podremos
comenzar la dispensa presionando el gatillo.
4. Durante el dispensado, puede accionar manualmente el
gatillo (1) o puede dejar el gatillo fijo mediante el botón
de bloqueo (2). En ambos casos, la válvula cortará
automáticamente el suministro cuando se alcance la
cantidad preseleccionada.
5. Si en cualquier momento, queremos cancelar o parar la
transacción, presiona el botón CANCEL. La pantalla
mostrará “CANCEL?” en la parte inferior de la misma y
deberemos confirmar el proceso pulsando el botón ENTER.
En dicho momento la transacción se cerrará y se enviará al
UTRACK. Si no quisieras parar la transacción pulsa el botón
CANCEL nuevamente para volver al estado anterior.
6. Si la transacción no es interrumpida, cuando la cantidad
dispensada alcance la cantidad objetivo, la válvula se cerrará
de forma automática y el mensaje de final de transacción
será enviado al UTRACK, mostrando por pantalla que no
existe ninguna transacción nueva en curso (“NO TR. IN
PROGRESS”) y apagándose para ahorrar batería.
001
CANCELLED
0.00
PRODUCT
001
CANCEL?
0.16
PRODUCT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Samoa 383406 Instructions Manual

Taper
Instructions Manual
Ce manuel convient également à

dans d''autres langues