Axis 5500 Manuel utilisateur

1

AXIS 5500/AXIS 5550 User’s Guide

AXIS 5500 / AXIS 5550

User’s Guide

English

AXIS 5500/AXIS 5550 User’s Guide

2

Regulatory Information

Safety Notices

Take some time to read through the safety notices before installing the Axis Network Print Server. Please observe all safety markings and instructions

when using this product.

Important:

Observe “Important:” in the text to avoid operational impairment. Do not proceed until you have fully understood the implications.

EMC USA

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may

cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B

of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take

whatever measures may be required to correct the interference. Compliance is not valid for unshielded network cables.

EMC Europe

This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022, and the requirements for immunity according to

EN55024 residential, commercial, and light industry. Compliance is not valid for unshielded network cables.

EMC Japan

This is a class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is

used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the

instruction manual. Compliance is not valid for unshielded network cables.

EMC Australia

This electronic device meets the requirements of the Radio communications (Electromagnetic Compatibility) Standard 1998 AS/NZS 3548. Compliance is

not valid for unshielded network cables.

Liability

Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform your local Axis office, which can

be found on the cover of this document. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the

right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with regard to the

material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of

this material.

Trademarks

AXIS IP JumpStarter, AXIS ThinWizard, axinstall, AXIS Print Monitor, Adobe Acrobat Reader, Aix, Apple, ARP, BOOTP, Debian, Ethernet, EtherTalk, IBM,

Internet Explorer, LAN Manager, LAN Server, Macintosh, Microsoft, Mozilla, NetScape, Novell NetWare, OS/2, OS/400, AS/400, Red Hat, Solaris, SuSe,

UNIX/Linux, Windows, are registered trademarks of the respective holders.

Support Services

Should you require technical assistance, please contact your Axis dealer. If your questions cannot be answered immediately, your Axis dealer will forward

your queries through the appropriate channels to ensure you a rapid response. If you are connected to the Internet, you can find on-line manuals,

technical support, software updates, application software, corporate information, etc. at http://www.axis.com/techsup/

Patent information

Axis AB has intellectual property rights relating to technology embodied in the product that is described in this document. In particular, and without

limitation, these intellectual property rights may include one or more of the patents listed at http://www.axis.com/patent.htm and one or more additional

patents or pending patent applications in the US and other countries.

Software Acknowledgments

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.

USER’S GUIDE AXIS 5500/5550 | R1 | Part nr: 20143

3

AXIS 5500/AXIS 5550 User’s Guide

Table of Contents

English Deutsch: 30

Hardware Inventory: 5

Quick Overview: 6

Connect the Hardware: 9

Assign an IP address: 10

- Automatic IP address assignment: 11

- Manual IP address assignment: 11

- - Setting the IP address using AXIS IP JumpStarter: 12

- - Setting the IP address using arp/ping: 13

- Verify access to the print server’s web pages: 14

Add Printers over the Network: 15

- Network Structures Overview: 16

- Adding Printers in Windows 2000/XP and NT: 17

- Adding Printers in Windows 98 and Me: 20

- Adding Printers in UNIX/Linux: 22

- Adding Printers in Mac OS X: 25

Print Server Management and Configuration: 26

- Web-based Print Server Management: 27

- Print Server Management using AXIS ThinWizard: 28

The Test Button: 29

Schnellübersicht: 31

Hardware installieren: 34

IP-Adresse zuweisen: 35

- IP-Adresse automatisch zuweisen: 36

- IP-Adresse manuell zuweisen: 36

- - IP-Adresse per AXIS IP JumpStarter zuweisen: 37

- - IP-Adresse per arp/ping zuweisen: 38

- Zugang zu den Webseiten des Druckerservers überprüfen: 39

Drucker über das Netzwerk hinzufügen: 40

- Überblick über Netzwerkstrukturen: 41

- Drucker unter Windows 2000/XP und NT hinzufügen: 42

- Drucker unter Windows 98 und Me hinzufügen: 46

- Drucker unter UNIX/Linux hinzufügen: 48

- Drucker unter Mac OS X hinzufügen: 51

Druckerserver-Verwaltung und -Konfiguration: 52

- Webbasierte Druckerserver-Verwaltung: 53

- Druckerserver-Verwaltung mit AXIS ThinWizard: 54

Taste „Test“: 55

Français: 56 Español: 82

Brève présentation: 57

Connexion du matériel: 60

Attribution d’une adresse IP: 61

- Attribution automatique d’une adresse IP: 62

- Attribution manuelle d’une adresse IP: 62

- - Définition de l’adresse IP à l’aide de AXIS IP JumpStarter: 63

- - Définition de l’adresse IP à l’aide de arp/ping: 64

- Vérification de l’accès aux pages Web du serveur d’impression: 65

Ajout d’imprimantes au réseau: 66

- Présentation des structures du réseau: 67

- Ajout d’imprimantes dans Windows 2000/XP et NT: 68

- Ajout d’imprimantes dans Windows 98 et Me: 72

- Ajout d’imprimantes dans UNIX/Linux: 74

- Ajout d’imprimantes dans Mac OS X: 77

Configuration et gestion du serveur d’impression: 78

- Gestion du serveur d’impression basée sur le Web: 79

- Gestion du serveur d’impression à l’aide de AXIS ThinWizard: 80

Le bouton de test: 81

Guía rápida: 83

Conexión del hardware: 86

Asignación de una dirección IP: 87

- Asignación automática de dirección IP: 88

- Asignación manual de dirección IP: 88

- - Configuración de la dirección IP con AXIS IP JumpStarter: 89

- - Configuración de la dirección IP con arp/ping: 90

- Verificación del acceso a las páginas Web del servidor de impresión: 92

Para agregar impresoras mediante la red: 93

- Presentación de las estructuras de red: 94

- Para agregar impresoras en Windows 2000/XP y NT: 95

- Para agregar impresoras en Windows 98 y Me: 98

- Para agregar impresoras en UNIX/Linux: 100

- Para agregar impresoras en Mac OS X: 103

Administración y configuración del servidor de impresión: 104

- Administración de servidor de impresión basada en la Web: 105

- Administración de servidor de impresión con AXIS ThinWizard: 106

El botón de prueba: 107

Italiano: 108

Panoramica sul prodotto: 109

Collegamento dell’hardware: 112

Assegnazione di un indirizzo IP: 113

- Assegnazione automatica di un indirizzo IP: 114

- Assegnazione manuale di un indirizzo IP: 114

- - Impostazione di un indirizzo IP mediante AXIS IP JumpStarter: 115

- - Impostazione di un indirizzo IP mediante arp/ping: 116

- Verifica dell’accesso alle pagine Web del server di stampa: 118

Aggiunta di stampanti sulla rete: 119

- Panoramica sulle strutture di rete: 120

- Aggiunta di stampanti in Windows 2000/XP e NT: 121

- Aggiunta di stampanti in Windows 98 e Me: 123

- Aggiunta di stampanti in UNIX/Linux: 126

- Aggiunta di stampanti in Mac OS X: 129

Gestione e configurazione del server di stampa: 130

- Gestione del server di stampa su base Web: 131

- Gestione del server di stampa mediante AXIS ThinWizard: 132

Pulsante Test: 133

English

AXIS 5500/AXIS 5550 User’s Guide

4

Before You Start

The instructions in this guide apply to:

AXIS 5500

AXIS 5550

with firmware version 6.40 (and higher).

The following operating systems are covered in this guide:

• Windows (98, Me, NT, 2000, XP)

•Mac OS X

• UNIX/Linux

The instructions in this guide are based on the settings found in a new and

unconfigured AXIS 5500/AXIS 5550.

To reload the default parameters, you can perform a Factory Default, which will restore most

settings to default values. See The Test Button on page 29 for instructions.

Note:

Installation instructions in this book cover the above operating systems over TCP/IP. For installation

instructions for Windows over NetBIOS/NetBEUI, NetWare over IPX/SPX and IP, and older versions of

Macintosh, as well as instructions on setting an IP address using RARP and BOOTP, see the AXIS 5500/AXIS

5550 User’s Manual, located on the AXIS Network Product CD (version 1.3 or later) and www.axis.com

5

AXIS 5500/AXIS 5550 User’s Guide

Hardware Inventory

Unpack and check all the items using the following check list. Contact your dealer if anything is

missing or damaged. All packing materials are recyclable.

Hardware Model Part Number

Network Print Server

AXIS 5500

AXIS 5550

0172-001

0173-001

Adhesive Holder & Clip

ACC AXIS 5500 CLIPS K 20119

USB Cable

20208

Power Adapter Model PS-H Part No.

PS-H

Australia 19111

Europe 19108

Korea 19112

UK 19109

USA / Japan 19110

Media Title Part Number

CD

AXIS Network Product CD rev 1.3 and up

Printed Material

AXIS 5500/5550 User’s Guide 20143 rev 1.0

Optional accessories Description Part Number

Cables

Parallel Printer Cable 13360

Centronics to Mini Centronics Cable 16453

Ribbons

Self-adhesive Velcro Ribbons 13282 and 13283

English

AXIS 5500/AXIS 5550 User’s Guide

6

Quick Overview

Print Server Installation

Follow these steps in order to get your Axis print server up and running:

1. Connect the Hardware, 9

2. Assign an IP address, 10

3. Add Printers over the Network, 15

Web-based Print Server Management

You can access the AXIS 5500/AXIS 5550 web pages to manage printing, perform firmware

upgrades, etc. See “Web-based Print Server Management” on page 27.

Multiple Print Server Management

In order to manage several Axis print servers simultaneously, you can install AXIS ThinWizard

software. AXIS ThinWizard is Windows 2000 and Windows XP compatible. See “Print Server

Management using AXIS ThinWizard” on page 28.

SSL/TLS support

AXIS 5500 and AXIS 5550 have built-in SSL/TLS support. To enable this, please refer to the

relevant sections in the AXIS 5500/5550 User’s Manual which is available on the AXIS Network

Product CD or from www.axis.com

AXIS Network Product CD

AXIS Network Product CD includes Axis Software, User Documentation, etc. All documents

presented on the CD are in PDF format.

You can download Acrobat Reader from the AXIS Network Product CD or www.adobe.com

7

AXIS 5500/AXIS 5550 User’s Guide

Mounting the Print Server

Using the supplied clips, your AXIS 5500/AXIS 5550 can be mounted in many ways, e.g. on the

back of the printer, on the side of the printer or on a wall. It can be placed behind the printer or

next to a hub.

AXIS 5550 can also be inserted directly into the parallel port of the printer.

Backside of print server

English

AXIS 5500/AXIS 5550 User’s Guide

8

AXIS 5500

AXIS 5550

Backside of AXIS 5500

Note: “S/N” can also appear as “Ser. No.” or “Serial no.”

Power Adapter

connector

Ethernet

connector

Network

indicator

Power

indicator

Test button

USB printer port (USB1)

Test button

Ethernet

connector Power Adapter

connector

Test button

Power

indicator

Network

Indicator

Parallel printer port (LPT1)

USB printer port (USB1)

MAC address

(Ethernet address)

example

9

AXIS 5500/AXIS 5550 User’s Guide

1. Connect the Hardware

1. Make sure that the printer is switched off and that the Power Adapter is disconnected from

the print server.

2. Locate the serial number, found on the underside label of the print server, and write it down.

Example: S/N: 00408c181636

3. Connect the printer to a port on the print server using an appropriate cable.

4. Connect the AXIS 5500/AXIS 5550 to your network (Ethernet Connector), using a twisted pair

category 5 cable.

5. Switch on the printer and make sure it is ready for use.

6. Connect the Power Adapter to the print server. The Network Indicator will start flashing when

the print server is correctly connected to the network.

7. Wait 1 minute and press the test button once. A test page will be printed on the connected printer

— keep it handy during the installation. The test page will show the assigned (static or dynamic)

IP address of the print server.

Note:

If you are installing an AXIS 5550 and have printers connected to both ports, the default setting will send the test

page to the parallel printer.

English

AXIS 5500/AXIS 5550 User’s Guide

10

2. Assign an IP address

To establish communication with the network, an IP address must be assigned to your AXIS

5500/AXIS 5550.

Select the method from the table below that applies to your network environment.

Automatic IP address assignment:

Manual IP address assignment:

These methods are all enabled by default.

Method: Server Required: Comment: Action:

Auto-IP Windows

environment

Automatic assignment of IP

addresses

Go to

Automatic IP address

assignment

, on page 11

DHCP DHCP server Dynamic assignment of IP

addresses

BOOTP BOOTP server Static assignment of IP

addresses

Method: Platform: Comment: Action:

AXIS ThinWizard Windows 2000,

XP

Axis software that assists in

finding, installing, monitoring,

configuring and upgrading

multiple print servers

simultaneously. Go to

“Manual IP address

assignment”

on page 11 for

instructions.

arp/ping

Windows,

UNIX/Linux, Mac

OS X

Requires the IP address for each

device to be downloaded

individually.

Cannot be used over routers.

AXIS IP

JumpStarter Windows

Axis software that allows you to

find print servers in your network

and assign an IP address to them.

11

AXIS 5500/AXIS 5550 User’s Guide

2.1 Automatic IP address assignment

If you are working in a Windows network with automatic IP address assignment, your print

server will obtain an IP address automatically when you connect it to the network. You will find

the IP address on the test page you printed out in “Connect the Hardware” on page 9.

Go to Verify access to the print server’s web pages, on page 14

2.2 Manual IP address assignment

To establish communication with the TCP/IP network, an IP address must be assigned to your AXIS

5500/AXIS 5550.

Choose the appropriate method of setting the IP address manually:

•AXIS ThinWizard for Windows 2000 and Windows XP. Axis software that assists in setting

the IP address of several print servers simultaneously.

Recommended for large organizations and enterprise networks.

Refer to Print Server Management using AXIS ThinWizard, on page 28

•arp/ping - use this method to set the IP address for each new device individually.

Refer to

Setting the IP address using arp/ping

on page 13 for instructions.

•AXIS IP JumpStarter - Axis software that locates print servers on your network and

allows you to assign an IP address to them. Recommended for small offices and local

networks. Refer to Setting the IP address using AXIS IP JumpStarter on page 12 for

instructions.

English

AXIS 5500/AXIS 5550 User’s Guide

12

2.2.1 Setting the IP address using AXIS IP JumpStarter

AXIS IP JumpStarter can also be used to set the IP address of the print server. Install AXIS IP

JumpStarter, which is available from the AXIS Network Product CD or from the Axis web site at

www.axis.com

1. Select the required server from the serial number list in the IP JumpStarter dialog window.

2. From the Server menu, select Set IP Address.

3. Click the radio button that corresponds to your choice of IP setting method. You must define

the Subnet Mask and Default Gateway when assigning a static IP address.

4. Click OK to save your settings.

5. Enter the server root password (by default set to pass), and click OK.

6. The AXIS 5500/AXIS 5550 will appear in the list with the assigned IP address.

7. To verify that you have access the print server’s web pages, highlight the print server in the list

and select Server Home Page from the Server menu.

Note:

If your print server does not appear in the serial number list, refer to the AXIS IP JumpStarter online help files or the

AXIS 5500/AXIS 5550 User’s Manual which is available on the AXIS Network Product CD or from www.axis.com

13

AXIS 5500/AXIS 5550 User’s Guide

2.2.2 Setting the IP address using arp/ping

Refer to the appropriate section below to assign an IP address to your AXIS 5500/AXIS 5550 using

arp/ping:

Windows

1. Open a Command Prompt and enter the following commands:

2. The host will return reply from 192.168.3.191, or a similar message. This indicates that

the address has been set and that communication is established.

3. Next, log in to the print server’s web pages ( - See page 14) and define the Default Router and

Subnet Mask of your network: choose admin | Network Settings | Detailed View | TCP/IP.

UNIX/Linux, Mac OS X

1. Open a Terminal window and enter the following commands:

2. The host will return 192.168.3.191 is alive, or a similar message. This indicates that

the address has been set and that communication is established.

3. Next, log in to the print server’s web pages ( - See page 14) and define the Default Router and

Subnet Mask of your network: choose admin | Network Settings | Detailed View | TCP/IP.

Notes:

Syntax Example

1.

arp -s <IP address> <Ethernet address> arp -s 192.168.3.191 00-40-8c-18-16-36

2.

ping <IP address> ping 192.168.3.191

3.

arp -d <IP address> arp -d 192.168.3.191

Syntax Example

1.

arp -s <IP address> <Ethernet address> arp -s 192.168.3.191 00:40:8c:18:16:36

2.

ping <IP address> ping 192.168.3.191

3.

arp -d <IP address> arp -d 192.168.3.191

•The Ethernet Address/MAC address is the same as the serial number, found on the print server’s underside

label. Enter the Ethernet Address in the same format as in the examples above.

•Setting the IP address with arp and ping is only possible during the first ten minutes after re-booting the

print server. Re-boot the print server by disconnecting and then re-connecting its power supply.

•When you execute the ping command for the first time, you may experience a significantly longer response

time than usual.

•You need root privileges on your UNIX/Linux and Mac system in order to execute the arp command (refer to

the User’s Manual for more information).

•Use the command man arp to get a list of arp commands in UNIX/Linux.

English

AXIS 5500/AXIS 5550 User’s Guide

14

2.3 Verify access to the print server’s web pages

Follow these instructions to verify that the IP address has been set and that you can access the

print server’s web pages:

1. Open a web browser (e.g. Internet Explorer, Netscape, Mozilla).

2. In the web browser’s Location/Address field, enter the print server’s IP address (found on the

test page or established when setting it manually) and press Enter.

3. If the Network Print Server web page appears in your web browser, the IP address has been

set correctly. Proceed to Add Printers over the Network, on page 15.

Notes:

See Web-based Print Server Management, on page 27 for more information on the print server’s internal web pages.

Use a web browser with JavaScript support.

15

AXIS 5500/AXIS 5550 User’s Guide

3. Add Printers over the Network

Follow the instructions to make network printers available for printing in Windows, UNIX/Linux

and Macintosh over TCP/IP.

In some cases, you need to install printing software. The software is available on the AXIS

Network Product CD and from the Axis web site www.axis.com

Refer to the table below for the appropriate method:

“Native tool” denotes the operating system’s own printing tool. e.g. Windows “Add Printer”.

Note:

Operating

systems

Install Software: See:

Windows

2000/XP/NT

No. Use native tool. Adding Printers in Windows 2000/XP and NT on page 17

Windows 98/Me Install AXIS

PrintMonitor software

Adding Printers in Windows 98 and Me on page 20

UNIX/Linux No. Use native tools

for lpd printing.

For ftp, PROS A and

PROS B printing,

install axinstall.

Adding Printers in UNIX/Linux on page 22

Mac OS X No. Use native tool. Adding Printers in Mac OS X on page 25

•To establish communication with the TCP/IP network, you must first assign an IP address to your AXIS

5500/AXIS 5550. See “Assign an IP address” on page 10.

•For printing from other platforms and protocols, see the AXIS 5500/AXIS 5550 User’s Manual.

English

AXIS 5500/AXIS 5550 User’s Guide

16

3.1 Network Structures Overview

Client/Server network

For client/server printing, each computer sends print jobs through a network server computer.

The printer must first be installed on the server computer (from the Add Printer Wizard, AXIS Print

Monitor) and then shared on the network, which makes it a network printer. It will then appear as

a Network Printer (in Windows Add Printer Wizard) on the client computers.

Each client computer must install the appropriate printer drivers in order to print properly.

Note for Windows 98/Me/NT:

Peer-to-Peer network

In Peer-to-Peer networks, each computer prints directly to the network printer. The network

printer appears as a Local Printer (in Windows Add Printer Wizard, AXIS PrintMonitor), and needs

to be added to each client computer that wants to print.

Each client computer must install the appropriate printer drivers in order to print properly.

Note for Windows 98/Me/NT:

It is only necessary to install AXIS PrintMonitor on a server for client/server printing.

AXIS Print Monitor must be installed on all (printing) client computers for Peer-to-Peer printing.

Print server

Printer Server computer

(Windows NT Server, NetWare Server, UNIX Server)

Network printer

Client computers

Network printer

Print server

Printer

17

AXIS 5500/AXIS 5550 User’s Guide

3.2 Adding Printers in Windows 2000/XP and NT

Follow the instructions below to use the standard Windows method for adding a network printer

in Windows 2000, XP and NT:

Windows XP:

1. Go to Start | Printers and Faxes and click the Add a Printer icon to start the Add Printer

Wizard. Click Next.

Windows 2000:

1. Go to Start | Settings | Printers and click the Add Printer icon to start the Add Printer

Wizard. Click Next.

2. Select the appropriate radio button:

Peer-to-Peer Printing:

•Local printer - If you are connecting directly to the print server, select Local Printer and click

Next. Click the Create a new port radio button and select Standard TCP/IP Port from the list.

Click Next and the Add Standard TCP/IP Printer Port Wizard starts. Click Next.

Enter the IP address of the print server (Example: 192.168.3.191) and click Next. Enter the

Device Port you want to use (Example: USB1). Click Next and Finish.

Select Manufacturer and Printer from the lists. Click Next. Choose whether you want to keep

the existing driver or to replace it. If you already have the printer’s driver installed, you will be

asked whether to keep it or to replace it. Click Next.

Supply a name for the printer and choose whether you want to make it your default printer.

Click Next. Choose whether you want to share the printer with other network users. Do you

want to print a test page? Select the appropriate radio button and click Next and Finish.

Client/Server Printing:

•Network printer - If your print server has already been installed on another computer, select

Network printer and click Next. Follow the instructions in the Add Printer Wizard to

complete the installation.

Ports available USB port Parallel port

AXIS 5500

AXIS 5550

USB1

—

LPT1

English

AXIS 5500/AXIS 5550 User’s Guide

18

Important!

If the USB port option does not appear:

Proceed to Print Server Management and Configuration on page 26 for information on supported

management and configuration tools.

•Make sure that the Automatically detect and install my Plug and Play printer checkbox is not checked.

•Press F1 to access the Windows online help system if you need additional help when installing a printer/print

server using this method.

•If you wish to print over LPR, double-click the installed printer from Start | (Settings) |Printers (and Faxes).

Select Properties from the Printer menu and click Ports then Configure Port. Click the LPR radio button and

enter the queue name under LPR Settings. The available queues are:

AXIS 5550: pr1, pr3, pr5, pr7= LPT1. Pr2, pr4, pr6, pr8=USB1

AXIS 5500: pr1-pr8= USB1. Click OK to finish.

If the USB port option does not appear when adding printers in Windows 2000 and XP, follow these

instructions to emulate a USB port:

Windows XP:

1. Go to Start | Printers and Faxes and click the Add a Printer icon to start the Add Printer Wizard. Click Next.

Windows 2000:

1. Go to Start | Settings | Printers and click the Add Printer icon to start the Add Printer Wizard. Click Next.

2. Select the Local Printer radio button and click Next. Click the Create a new port radio button and select Standard

TCP/IP Port from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard starts. Click Next.

3. Enter the name of the print server (Example: AXIS100086 or the IP address) and click Next. Enter the Device

Port you want to use:

5500: choose LPT1

5550: Choose LPT2 for if you are installing a USB port and LPT1 if you are installing a parallel port. Click

Next and Finish.

Select Manufacturer and Printer from the lists. Click Next. Choose whether you want to keep the existing

driver or to replace it. If you already have the printer’s driver installed, you will be asked whether to keep it or

to replace it. Click Next.

Supply a name for the printer and choose whether you want to make it your default printer. Click Next.

Choose whether you want to share the printer with other network users. Do you want to print a test page?

Select the appropriate radio button and click Next and Finish.

4. Go to Start | (Settings) | Printers (and Faxes) and highlight your newly installed printer. Right-click and choose

Properties. Choose the Ports tab (make sure your printer is highlighted) and then Configure Port...Under

Protocol, click the Raw radio button and then define the printer port under Raw Settings - Port Number as

follows:

5500: 9100

5550: USB = 9101, LPT1 = 9100

Click OK and close the window. Print a test page to verify your installation.

19

AXIS 5500/AXIS 5550 User’s Guide

Windows NT 4 over TCP/IP:

1. Go to Start | Settings | Printers | Add Printer. Select My Computer (for peer-to-peer

printing) and click Next.

2. From the Available Ports list, choose the appropriate printer port, which will appear as the IP

address or host name of the print server. Skip to step 7.

3. If the IP address or host name of the print server you wish to use does not appear in the list,

click Add Port.

4. Choose LPR Port from Available Printer Ports and click New Port.

5. Type the print server’s IP address (or host name) in the field Name or address of server providing

lpd (Example IP address: 192.168.3.191). Then enter which port to use in the field Name of

printer or print queue on that server according to the table below (Example: USB1). Click OK

and then Close.

6. The added print server will now appear in the Available Ports list.

7. Click Next, choose an appropriate driver and finish the installation as usual.

Note:

Ports available USB port Parallel port

AXIS 5500

AXIS 5550

USB1

—

LPT1

If LPR port does not appear in the Available Printer Ports list, you need to install the Microsoft TCP/IP Printing

Service, delivered with the Windows NT 4 Operating System.

English

AXIS 5500/AXIS 5550 User’s Guide

20

3.3 Adding Printers in Windows 98 and Me

AXIS Print Monitor is the recommended tool to use for network printing in Windows 98 and Me.

It allows AXIS 5500/AXIS 5550 to be connected in the same simple fashion as a local printer.

Note:

1. To start the Add Printer Wizard, select Settings | Printers from the Start menu and

double-click the Add Printer icon.

2. After clicking Next in the first dialog, the Wizard asks you to select between Local Printer and

Network Printer. You must select Local Printer as the AXIS 5500/AXIS 5550 emulates a local

printer port. Click Next.

3. Choose the appropriate print driver for your printer. If the desired print driver already appears

within the displayed Manufacturers and printers lists, highlight your selection, click Next and

proceed directly to step 6. It is only necessary to perform steps 4 - 5 if your printer does not

feature in the model list.

4. Click the Have Disk... button. Insert the printer driver diskette/CD into the appropriate disk drive

of your computer. If the floppy disk drive is A:, then click OK, otherwise type the letter of your

disk drive and then click OK.

5. Select the type of printer you want to install from the diskette/CD and click Next.

6. Select the Printers@TCP/IP Port and click Next.

7. Enter an appropriate name for your printer and choose whether you want it to be the default

printer. Click Next.

8. In the next window, do not order a Test Page to be written, just click Finish.

9. AXIS Print Monitor now informs you that the printer has to be connected to another port. Click

OK.

10. The printer you have defined will now be displayed in the Printers Folder. Right-click the printer

object and select Properties from the Context menu.

11. Click the Details tab within the Properties page and then click Add Port to display the available

monitors.

12. Click the radio button “other”. Select AXIS Port and then click OK.

13. Select RAW (TCP/IP) as your choice of protocol and click OK.

For peer-to-peer printing, AXIS Print Monitor must be installed on all printing clients, while it is only necessary to

install it on the server for client/server printing.

La page est en cours de chargement...

Axis 5500 Manuel utilisateur

Ce manuel convient également à

Axis 5500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents