Progress Lighting P250007-108-30 Mode d'emploi

Marque: Progress Lighting

Modèle: P250007-108-30

Taper: Mode d'emploi

Ce manuel convient également à

P250007

93133616_B C

Limited Lifetime Warranty

Date Purchased

Store Purchased

UL Model No.

Serial No.

Vendor No.

UPC

111017

P250007

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical

defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and

metal nishes are warranted to be free from defects in materials or workmanship for a period of 1 year from

the date of purchase. Warping of wooden or plastic blades is not covered by this warranty nor is corrosion and/

or deterioration of any nishes for fans installed within ten miles of any sea coast. Extended warranties for

ENERGY STAR® qualied products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal

conditions of use, are warranted to be free from defects in material and workmanship which cause the light

sources to fail to operate in accordance with the specications for (i) ve (5) years from the date of purchase

on the LED Light modules and electrical components for fans used in single family residences, and (ii) three

(3) years from the date of purchase on the LED Light modules and electrical components for fans used in

multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no warranty other

than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the

rst 30 days for replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864)

678-1000 for repair or replacement which shall be determined in Progress Lighting’s sole discretion and shall

be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor

(including, but not limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration,

misuse, abuse or neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser

or a third party, including without limitation improper voltage supply or power surge, use of improper parts or

accessories, unauthorized repair (made or attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION

AND ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS.

PROGRESS LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL,

INCIDENTIAL OR CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF

BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN

IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations

of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This

warranty gives you specic rights and you may have other rights which vary from state to state.

785247249329

785247249312

785247249336

Safety Rules

Unpacking Your Fan

Installing Your Fan

Setting the Codes

Making the Electrical Connections

Operating Your Fan

Care of Your Fan

Troubleshooting

Specications

Table of Contents

1. To reduce the risk of electric shock, insure electricity

has been turned off at the circuit breaker or fuse box

before beginning.

2. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70-1999 and local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

3. CAUTION: To reduce the risk of personal injury, use

only the screws provided with the electrical box.

4. The outlet box and support structure must be securely

mounted and capable of reliably supporting 35 lbs.

(15.9 kg). Use only UL Listed outlet boxes marked

“Acceptable for Fan Support of 35 lbs. (15.9 kg) or less.”

5. CAUTION: The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of the blades

to the oor.

6. Do not operate reversing switch while fan blades are

in motion. Fan must be turned off and blades stopped

before reversing blade direction.

7. Avoid placing objects in path of the blades.

8. To avoid personal injury or damage to the fan and other

items, be cautious when working around or

cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into

electrical box. The wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the electrical box and ungrounded

conductor on the other side of the electrical box.

11. Electrical diagrams are for reference only. Light kits that

are not packed with the fan must be cUL Listed and marked

suitable for use with the model fan you are installing.

Switches must be cUL General Use Switches. Refer to the

instructions packaged with the light kits and switches for

proper assembly.

12. All set screws must be checked and retightened where

necessary before installation.

13. WARNING: To reduce the risk of re or electric shock, do

not use this fan with any solid-state speed control device.

14. Use with speed controller UC7067RYE, manufactured by

Rhine Electronic Co., Ltd only.

1. Safety Rules

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN

SUPPORT OF 35LBS. (15.9 KG) OR LESS”, AND USE SCREWS PRO-

VIDED WITH THE OUTLET BOX.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS (“FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED

WITH AN ISOLATION CONTROL/SWITCH.

a. Blade attachment hardware

(16 screws for attaching blades to blade

arms)

b. Electrical hardware and balancing kit

(3 plastic wire connectors, blade balancing

kit)

c. Blade bracket attachment hardware

(1 extra screw for attaching blade arms to

the fan motor assembly)

7. Blades (5)

8. Light Kit Pan

9. Light Kit Fitter Assembly

10. Light Shade

11. Transmitter and Receiver

1. Mounting Bracket (inside canopy)

2. 6” Ball/Downrod Assembly (hanger pin

and locking pin pre-attached)

3. Canopy with Canopy Ring (attached)

4. Decorative Motor Collar Cover

5. Fan Motor Assembly

6. Blade Arm (5)

2. Unpacking Your Fan

Unpack your fan and check the contents. You should have the following items:

3. Installing Your Fan

Tools Required

Phillips screw driver or straight slotted screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing electrical box, then

read the following instructions. Disconnect

the power by removing fuses or turning off

circuit breakers.

Secure the electrical box directly to the building

structure. Use appropriate fasteners and

building materials. The electrical box and

its support must be able to fully support the

moving weight of the fan (at least 35 lbs.).

Do not use plastic electrical boxes.

Figures 1, 2, and 3 are examples of different

ways to mount the electrical box.

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling. The maximum

angle allowable is 20˚. If the canopy touches

downrod, remove the decorative canopy

bottom cover and turn the canopy 180˚ before

attaching the canopy to the mounting plate.

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

TO OUTLET BOX MARKED “ACCEPTABLE

FOR FAN SUPPORT OF 35LBS. (15.9 KG) OR

LESS”, AND USE SCREWS PROVIDED WITH

THE OUTLET BOX. ELECTRICAL BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPT-

ABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELEC-

TRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly.

NOTE: This fan is recommended for

standard ceiling mount using the downrod

provided with this fan. When using standard

ceiling installation with the 6 inch downrod

provided, the distance from the ceiling

to the bottom of the fan blades will be

approximately 14 inches.

Standard Ceiling Mounting

1. Remove the canopy ring from the canopy

by turning the ring counter-clockwise

until it unlocks. (Figure 5)

2. Remove the mounting bracket from the

canopy by loosening the four screws on

the top of the canopy. Remove the two

non-slotted screws and loosen the slotted

screws. This will enable you to remove

the mounting bracket. (Figure 6)

3. Remove the hanger pin and locking pin

from downrod assembly.

4. Route the wires exiting the top of the fan

motor through the decorative motor collar

cover then the canopy ring. Make sure the

slot openings are on top. Route the wires

through the canopy and then through the

ball/downrod assembly. (Figure 7)

Remove

Loosen but Do Not Remove

Turn Canopy Ring to Remove

Figure 5

Figure 6

5. Loosen, but do not remove, the set screws

on the collar on the top of the motor

housing.

6. Align the holes at the bottom of the

downrod with the holes in the collar on top

of the motor housing. (Figure 7)

Carefully insert the hanger pin through the

holes in the collar and downrod. Be careful

not to jam the hanger pin against the wiring

inside the downrod. Insert the locking pin

through the hole near the end of the bolt

until it snaps into its locked position, as

noted in the circle inset of Figure 7.

7. Re-tighten the set screws on the collar on

top of the motor housing.

8. Make sure the grommet is properly installed

in the collar cover, then slide the collar cover

on the downrod until it rests on the motor

housing. Be sure that the canopy and the

collar cover are both oriented correctly.

9. Proceed to “Installing the Fan” section.

FAILURE TO PROPERLY INSTALL SET SCREWS

AS NOTED IN STEP 7 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Figure 7

Pin in

locked

position

Motor Wires

Ball/Downrod

assembly

Canopy

ring

Motor collar

cover

Hanger

Motor

collar

Reverse

switch

Locking

Tighten

screws

Standard mounting

Installing Fan to

the Electrical Box

1. Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket

as shown in Figure 8.

2. Install the ceiling mounting bracket on the

electrical box by using the mounting screws

provided with the electrical box. Note that

the at side of the mounting bracket is

toward the electrical box. (Figure 8)

3. Tighten the two screws on the electrical box

securely.

4. Carefully lift the fan assembly up to the

ceiling mounting bracket. Make sure the tab

on the mounting bracket is properly seated

in the groove in the hanger ball. (Figure 9)

Figure 8

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE

BOTTOM OF THE MOUNTING BRACKET MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

Figure 9

Connecting the Safety

Cable

1. Turn the wood screw (LL)(not provided)

into the ceiling.

2. Place the looped end of the safety cable (S)

onto the wood screw and then tighten the

screw rmly, or connect the safety cable

directly to the electrical box. (Figure 10)

Figure 10

6. Setting the Code

Setting the Codes

This unit has 16 different code combinations

to prevent possible interference from other

remote units such as garage door openers, car

alarms or security systems.

To set the codes, perform the following steps:

1. Setting the code on the transmitter:

a. Remove the battery cover from the

battery compartment on the back side of

the transmitter.

b. Slide code switches to your choice of up

or down position (factory setting is up).

c. Replace the battery cover on the battery

compartment of the transmitter.

2. Setting the code on the receiver:

a. Slide code switches to the same position

as set on your transmitter.

Model:UC7085T

FCC ID:CHQ7085T

IC:2968A-7085T

Complies with Canada

RSS-210

MADE IN CHINA

Airpro

1 2 3 4

N ECE

12V

1 2 3 4

ON DIP

1 2 3 4

ON DIP

1 2 3 4

NECE

Dip Switches

Transmitter

Receiver

Figure 11

EACH WIRE NUT (WIRE CONNECTOR) SUPPLIED

WITH THIS FAN IS DESIGNED TO ACCEPT UP TO

ONE 12 GAUGE HOUSE WIRE AND TWO WIRES

FROM THIS FAN. IF YOU HAVE LARGER THAN

12 GAUGE HOUSE WIRING OR MORE THAN

ONE HOUSE WIRE TO CONNECT TO THE FAN

WIRING, CONSULT AN ELECTRICIAN FOR THE

PROPER SIZE WIRE NUTS TO USE.

USE THE PLASTIC WIRE CONNECTORS

SUPPLIED WITH YOUR FAN. SECURE THE

CONNECTORS WITH ELECTRICAL TAPE AND

ENSURE THERE ARE NO LOOSE STRANDS OR

CONNECTIONS.

BLUE

BLACK

WHITE

GREEN

BLUE

BLACK WHITE

WHITE

SUPPLY CIRCUIT

BLACK

WHITE

Grounding

Conductor

Green

Grounding

Lead

Remote

Receiver

Figure 12

Making the Electrical

Connections

REMEMBER to disconnect the power. If

you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts supplied with your fan and

supplied with remote control. Secure the

connectors with electrical tape. Make sure

there are no loose strands or

connections. (Figure 12)

1. Connect the ground conductor of the 120v

supply (this may be a bare wire or a wire

with green colored insulation) to the green

ground lead(s) of the fan (Figure 12).

2. Connect the fan motor white wire to the

receiver white wire using a wire nut (Figure

12).

3. Connect the fan motor black wire to the

receiver black wire using a wire nut (Figure

12).

4. Connect the fan motor blue wire to the

receiver blue wire using a wire nut (Figure

12).

5. Connect the receiver black wire to the

supply black (hot) wire using a wire nut

(Figure 12).

6. Connect the receiver white wire to the

supply white (neutral) wire using a wire nut

(Figure 12).

7. After connecting the wires, spread them

apart so that the green and white wires are

one side of the electrical box and the black

wire is on the other side.

8. Turn the wire connecting nuts upward and

carefully push the wiring into the electrical

box.

Attaching the Fan

Blades

Figure 13

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1. Align the locking slots of the ceiling

canopy with the two screws in the

mounting plate. Push up to engage the

slots and turn clockwise to lock in place.

Immediately tighten the two mounting

screws rmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

rmly.

3. Install the decorative canopy ring by

aligning the ring’s slots with the screws in

the canopy. Rotate the ring clockwise to

lock in place.

4. You may now proceed to attaching the

fan blades.

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE

BOTTOM OF THE MOUNTING PLATE MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

Screws

Blade

Figure 14

Slot

Blade Arm

Screws

Alignment Post

1. Attach blade to blade bracket using

the screws as shown in gure 13.

Start a screw into the bracket. Repeat

for the two remaining screws.

2. Tighten each screw securely.

3. Fasten the blade assembly to the

motor by inserting the alignment

post into the slot on the bottom of

the motor and tightening the motor

screws. Please note that the motor

screws are pre-attached into the blade

brackets (Figure 14).

4. Repeat steps 1,2 and 3 for the

remaining blades.

NOTE: Your fan blades are reversible.

Select the blade side nish which best

accentuates your decor.

Figure 15

Blade Balancing

All blades are grouped by weight. Because

natural woods vary in density, the fan may

wobble even though the blades are weight

matched.

The following procedure should correct most

fan wobble. Check after each step.

1. Check that all blade screws are secure.

2. Most fan wobble problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

from a point on the center of each blade

to the point on the ceiling. Measure this

distance as shown in Figure 14. Rotate

the fan until the next blade is positioned

for measurement. Repeat for each blade.

Measurements deviation should be within

1/8”. Run the fan for 10 minutes.

3. Make sure that canopy is tightened securely

to ceiling mounting bracket and that the

ceiling mounting bracket is tightened

securely to the electrical box.

4. Interchanging two adjacent blades can

redistribute the weight and possibly result

in the smoother operation.

5. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

Touching

Ceiling

10.

Installing the Light Kit

Pan/Light Kit Fitter

Assembly/ Light Shade

CAUTION - To reduce the risk of electrical

shock, disconnect the electrical supply circuit

to the fan before installing the light kit.

1. Loosen but do not remove two of three

mounting screws from the fan motor

assembly; Remove one mounting screw.

(Figure 16)

2. Push the light kit pan up to the fan motor

assembly so that the two loosened screw

heads t into the keyhole slots. Turn the

light kit pan clockwise, tightened the

screws. Re-install the screw that was

removed in step 1 and tighten rmly.

(Figure 16)

3. Remove one screw from the light kit pan

and loosen, but do not remove the other

two screws. Connect the wires from the

light kit tter assembly to the wires from

the fan motor assembly by connecting the

molded adaptor plugs together. Carefully

tuck all wires and splices into the switch

cap. (Figure 17)

4. Push the light kit tter assembly up so

that the two loosened screw heads t into

the keyhole slots. Turn the light kit tter

assembly clockwise, tighten the screws. Re-

install the screw that was removed in step 3

and tighten rmly. (Figure 17)

5. Place the light shade into the light kit pan,

aligning the three at areas on the top of the

light shade with the three raised dimples

in the light kit pan. Turn the light shade

clockwise until it stops. (Figure 18)

Light Kit

Pan

Mounting Screws

Screws

Figure 16

Figure 17

PERIODICALLY CHECK THE SHATTER-

RESISTANT SHADE IS SEATED FULLY

CLOCKWISE IN THE LIGHT KIT PAN

ASSEMBLY.

Figure 18

11. Operating Your Fan11. Operating Your Fan

Speed settings for warm or cool weather depend

on factors such as room size, ceiling height,

number of fans, and so on.

Figure 20

Figure 21

Warm weather - (Forward) A downward air

ow creates a cooling effect as shown in Figure

20. This allows you to set your air conditioner

on a higher setting without affecting your

comfort.

Cool weather - (Reverse) An upward air ow

moves warm air off the ceiling are as shown in

Figure 21. This allows you to set your heating

unit on a lower setting without affecting your

comfort.

Remote Control - Your fan is equipped with a

remote control to operate the speed and lights

of your new ceiling fan (Figure 19).

Model:UC7085T

FCC ID:CHQ7085T

IC:2968A-7085T

Complies with Canada

RSS-210

MADE IN CHINA

Airpro

1 2 3 4

NECE

12V

Figure 19

Key -

High speed

Medium speed

Low speed

Light on/off and dimmer (press

and hold to dim light)

Fan off

The fan shipped from the factory with the

reversing switch positioned to circulate air

downward. If airow is desired in the opposite

direction, turn your fan off and wait for the

blades to stop turning, then slide the reversing

switch (located at the top of the motor housing,

refer to gure 7 on page 4) to opposite position,

and turn fan on again. The fan blades will turn

in the opposite direction and reverse airow.

12. Care of Your Fan and Troubleshooting

Care of Your Fan

Here are some suggestions to help you

maintain your fan.

1. Because of the fan’s natural movement,

some connections may become loose.

Check the support connections, brackets,

and blade attachments twice a year. Make

sure they are secure. (It is not necessary to

remove fan from ceiling.)

2. Clean your fan periodically to help maintain

its new appearance over the years. Do not

use water when cleaning, this could damage

the motor, or the wood or possibly cause

an electrical shock. Use only a soft brush

or lint-free cloth to avoid scratching the

nish. The plating is sealed with a lacquer

to minimize discoloration or tarnishing.

Warning - Make sure the power is off

before cleaning your fan.

3. You can apply a light coat of furniture polish

to the wood for additional protection and

enhanced beauty. Cover small scratches

with a light application of shoe polish.

4. There is no need to oil your fan.

The motor has permanently lubricated

sealed ball bearings. MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX

BEFORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION,

“MAKING ELECTRICAL CONNECTIONS.”

Fan will not start

Fan sounds noisy

1. Check main and branch circuit fuses or breakers

2. Check line wire connections to the fan and switch wire connections in

the switch housing. CAUTION: Make sure main power is off.

3. Check batteries in the transmitter. Does the red LED light come on?

Are you standing close enough to the fan? (Normal range is 10-20

feet.) Are the dip switch settings the same on the transmitter (hand unit)

and receiver? REMEMBER TO TURN OFF POWER SUPPLY

BEFORE CHECKING THE DIP SWITCH SETTINGS IN

RECEIVER.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub

are tight.

3. Make sure wire nut connections are not rattling against each other or

the interior wall of the switch housing.

CAUTION: Make sure power is off.

4. Allow a 24-hour “breaking in” period. Most noises associated with a

new fan disappear during this time.

5. If using the Ceiling Fan light kit, make sure the screws securing the

glassware are tight. Check that the light bulb is also secure.

6. Make sure the canopy is a short distance from the ceiling.

It should not touch the ceiling.

7. Make sure your electrical box is secure and rubber isolator pads were

used between the mounting bracket and electrical box.

Troubleshooting

Problem Solution

13. Specications

FAN

SIZE SPEED VOLTS

FAN POWER

CONSUMPTION

(WITHOUT LIGHTS)

WATTS

AIRFLOW

CFM

AIRFLOW

EFFICIENCY

(HIGHER IS BETTER)

CFM/WATT

NET

WEIGHT

GROSS

WEIGHT

CUBE

FEET

54”

Low

120

11 2364 215 19.76

Lbs

22.4

Lbs 1.74

High 61 5553 91

701 Millennium Blvd.,

Greenville, SC 29607

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause undesired operation.

Manual de instalación de ventilador de techo

P250007

93133616_B C

Garantía limitada de por vida

Fecha de compra

Tienda donde se compró

Modelo UL Nº.

Número de serie

Proveedor Nº.

UPC

111017

P250007

Los motores de ventilador Progress Lighting se garantizan al comprador original como libres de defectos eléctricos

y/o mecánicos por el tiempo en que estén en su posesión como dueño. Los interruptores activados por cadena, los

interruptores de reversa, los capacitores y los acabados de metal se garantizan como libres de defectos materiales o de

fabricación por el plazo de 1 año desde la fecha de compra. Las deformaciones de las aspas de madera o plástico no

están cubiertas por esta garantía. Tampoco lo están la corrosión y/o deterioro del acabado de ventiladores instalados

a menos de diez millas de cualquier costa del mar. Pudieran aplicarse garantías extendidas para productos ENERGY

STAR® que caliquen.

Los ventiladores de techo Progress Lighting con fuentes de luz LED incorporadas, si han sido bien instalados y

bajo condiciones normales de uso, se garantizan como libres de defectos materiales y de fabricación que puedan

causar un fallo en el funcionamiento según las especicaciones de dichas fuentes de luz durante un periodo de (i)

cinco (5) años a partir de la fecha de compra para los módulos de luz LED y componentes eléctricos de ventiladores

usados en residencias unifamiliares y durante (ii) tres (3) años para ventiladores usados residencias multifamiliares

o en instalaciones comerciales. Las bombillas LED suministradas por Progress Lighting sólo poseen la garantía del

fabricante. Las bombillas que no sean LED no tienen garantía.

Con prueba de la compra, el comprador original puede devolver el ventilador defectuoso, para su reposición, al lugar

donde lo compró, dentro de los 30 días siguientes a la compra. Pasados 30 días, el comprador original TIENE que

contactar a Progress Lighting llamando al (864) 678-1000 para reparación o reposición, según determine Progress

Lighting a su entera discreción, y este será el único y exclusivo remedio del comprador.

Se excluyen cargos por mano de obra y envío. Esta garantía no cubre ningún costo ni cargo asociado a la mano de

obra (incluyendo, pero sin limitarse a, los cargos del electricista) que se requiera para instalar, retirar o reponer un

ventilador o cualquiera de sus partes.

Esta garantía no cubre ninguna pérdida o daño resultante de (i) desgaste normal o alteración, mal uso, abuso o

negligencia, o (ii) instalación, operación, reparación o mantenimiento incorrectos por el comprador original o un

tercero, incluso sin limitación del suministro de tensión o sobrecarga de alimentación, uso de piezas o accesorios

inadecuados, reparación no autorizada (realizada o intentada) o falta de mantenimiento al ventilador.

LAS GARANTÍAS ANTERIORES ESTABLECEN LA OBLIGACIÓN DE GARANTÍA TOTAL DE PROGRESS

LIGHTING Y EL ÚNICO Y EXCLUSIVO REMEDIO DEL COMPRADOR ORIGINAL RELACIONADO CON

DICHOS PRODUCTOS. PROGRESS LIGHTING NO ES RESPONSABLE POR NINGÚN DAÑO (SEAN

INDIRECTOS, ESPECIALES, INCIDENTALES O CONSECUENTES) DEBIDO A FALLAS DEL PRODUCTO,

YA SEAN DERIVADAS DE INCUMPLIMIENTO DE LA GARANTÍA O DEL CONTRATO, O DE CUALQUIER

OTRA CAUSA. ESTA GARANTÍA SE OTORGA EN LUGAR DE TODAS LAS DEMÁS, YA SEAN EXPRESAS O

IMPLÍCITAS, INCLUIDAS LAS GARANTÍAS DE COMERCIABILIDAD, IDONEIDAD PARA UN PROPÓSITO

EN PARTICULAR O NO INFRACCIÓN.

Algunos estados no permiten limitaciones en la duración de una garantía implícita ni exclusión o limitaciones de

daños incidentales o consecuentes, así que las exclusiones o limitaciones anteriores pudieran no aplicarse a su caso.

Esta garantía le otorga derechos especícos y es posible que usted tenga otros, que varían de estado a estado.

785247249329

785247249312

785247249336

Normas de seguridad

Cómo desempacar el ventilador

Cómo instalar el ventilador

Cómo congurar los códigos

Cómo hacer las conexiones eléctricas

Cómo usar el ventilador

Cuidado del ventilador

Solución de problemas

Especicaciones

Tabla de contenido

1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la

instalación asegúrate de que la electricidad

ha sido cortada en el cortacircuitos o en la caja de fusibles.

2. Todo el cableado tiene que cumplir con el Código Nacional de

Electricidad ANSI/NFPA 70-1999 y con los códigos locales

de electricidad. La instalación eléctrica debe hacerse por un

electricista calicado y con licencia.

3. PRECAUCIÓN: Para reducir el riesgo de lesiones físicas, usa sólo

los tornillos suministrados con la caja de distribución.

4. La caja eléctrica y estructura de soporte tienen que montarse de

forma segura para poder sostener con conanza 35 lb. (15.9 kg).

Usar solo cajas eléctricas aprobadas por UL con la marca “Apto

para sostener ventiladores de 35 lb (15.9 kg) o menos”.

5. PRECAUCIÓN: El ventilador tiene que montarse con al menos

7 pies (2.13 m) de separación entre el borde trasero de las aspas y

el piso.

6. No operar el interruptor de reversa mientras las aspas del ventilador

estén en movimiento. El ventilador tiene que estar apagado y las

aspas detenidas antes de invertir el sentido del movimiento.

7. Evita colocar objetos en la trayectoria de las aspas.

8. Para evitar lesiones personales o daños al ventilador y otros artículos,

ten cuidado al limpiarlo o al trabajar cerca de él.

9. No usar agua ni detergentes para limpiar el ventilador o las aspas.

Para limpiar, casi siempre será adecuado un paño seco o ligeramente

humedecido con que quitar el polvo.

10. Después de hacer las conexiones eléctricas, los conductores

empalmados deben voltearse hacia arriba y empujarse con cuidado

dentro de la caja eléctrica. Los cables deben estar separados, con el

cable y el conductor a tierra del equipo

hacia uno de los lados de la caja eléctrica, y el conductor sin conexión

a tierra hacia el lado opuesto.

11. Los diagramas eléctricos son solo para referencia. Los kits de luces

que no vienen en la caja del ventilador tienen que estar aprobados

por cUL y marcados como apropiados para usar con el modelo

de ventilador que estás instalando. Los interruptores deben ser

interruptores cUL de uso general. Para ensamblar bien, consulta las

instrucciones adjuntas a los kits de luces e interruptores.

12. Antes de la instalación, todos los tornillos de jación tienen que

comprobarse y reajustarse donde sea necesario.

13. ADVERTENCIA: Para reducir el riesgo de incendio o descarga

eléctrica, no utilices este ventilador con ningún dispositivo de estado

sólido para control de velocidad.

14. Usa sólo con el Controlador de Velocidad UC7067RYE, fabricado por

Rhine Electronic Co., Ltd.

1. Normas de seguridad

LEE Y GUARDA ESTAS INSTRUCCIONES

PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA U OTRAS

LESIONES, INSTALA SÓLO EN UNA CAJA ELÉCTRICA CLASIFICADA COMO

“APROPIADA PARA SOSTENER VENTILADORES DE 35 LB (15.9 KG). O ME-

NOS”, Y USA SÓLO LOS TORNILLOS INCLUIDOS CON LA CAJA ELÉCTRICA.

PARA REDUCIR EL RIESGO DE LESIONES PERSONALES, NO DOBLES LOS

BRAZOS DE LAS ASPAS (TAMBIÉN LLAMADOS “REBORDES”) NI DURANTE NI

DESPUÉS DE LA INSTALACIÓN. NO COLOCAR OBJETOS EN LA TRAYECTORIA

DE LAS ASPAS.

PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, ESTE VENTILADOR

TIENE QUE INSTALARSE CON UN CONTROL/INTERRUPTOR DE AISLAMIENTO.

ADVERTENCIA

La page charge ...

Progress Lighting P250007-108-30 Mode d'emploi

Marque: Progress Lighting

Modèle: P250007-108-30

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Progress Lighting P250007-108-30 Operating instructions
español: Progress Lighting P250007-108-30 Instrucciones de operación

Progress Lighting P250007-108-30 Mode d'emploi

Ce manuel convient également à

Progress Lighting P250007-108-30 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents