Johnson Controls Prox-PG Mode d'emploi

Prox-PG
Johnson Controls
Marque
Johnson Controls
Modèle
Prox-PG
Catégorie
Pavés numériques
Taper
Mode d'emploi
IQ Keypad is a battery powered, capacitive touch keypad for use with compatible IQ4 NS, IQ4 Hub &
IQ Panel 4 platforms via the PowerG protocol. It provides an easy and intuitive interface to control
basic features of the system. This manual covers both IQ Keypad Prox-PG and IQ Keypad-PG
models.
Document: IQKP-UG
Version: 1.0.0
Date: 06/05/2023
IQ KEYPAD USER GUIDE
USING YOUR SYSTEM: OVERVIEW
Prox Tag Reader
(IQ Keypad Prox-PG
only)
Arm Stay
Arm Away
Arm Night
Trouble LED
Armed Status
LED
Disarmed Status
LED
Fire Emergency
(1+3)
Hold for 2 sec
Police Emergency
(7+9)
Hold for 2 sec
Aux Emergency
(4+6)
Hold for 2 sec
USING YOUR SYSTEM: BASICS
KEYPAD STATUS LIGHTS:
Status lights help you understand the state of the system at a glance.
USING YOUR IQ KEYPAD
Status Lights
LED
Description
OFF
Not ready to Arm.
ON
Ready to Arm.
FLASHING
Ready to Arm, bypass-able zones are open.
OFF
Disarmed
ON
Armed
FLASHES TWICE
Message sent successfully
FLASHING
Alarm occurred
RAPID FLASHING
Bell silenced for Fire Alarms
OFF
No Trouble
ON
System Trouble
FLASHING
Keypad Low Battery
Key
ARMING KEYS:
Arming keys are the primary way of controlling the system from the IQ Keypad.
NOTE: Press and hold arming keys for two seconds. If successful, the Armed Status LED will flash twice. If communication
is not successful, the keypad flashes all keypad number LED’s (backlight) 0.5 seconds ON/OFF twice.
Access code required for arming is off by default. If this is enabled in the panel (Secure Arming option), pressing each arm
button shall be followed by a correct access code otherwise the system will not arm.
Pressing * followed by Arm Away shall do a silent away arm
Pressing * followed by Arm Stay shall do a silent stay arm
Pressing * followed by Arm Night shall do a silent night arm
If access code is required to arm (panel setting) an access code must be entered after the sequence.
Example * > arm away > access code = silent away arm
PROX TAG SUPPORT:
For “IQ Keypad Prox-PG” models that support Prox Tags, simply present your tag in front of the bullseye
icon on the lower right hand side of the keypad and it will light up indicating the the tag has been read
successfully.
USING YOUR SYSTEM: BASICS
Press
Action
[*] + [Arm/Disarm Button]
Silent Arm/Disarm
[*][1] + [Access Code]
Bypass all open Zones
[*][4] + [Access Code]
Toggle Chime On/Off
[*][6] + [Access Code]
Toggle Keypress Buzzer On/Off
[*][7] + [Output #] + [Access Code]
Toggle Command Output
[*][8] + [Access Code]
Turn on Installer Programming Access (EN Grade 2 only)
[*][9] + [Access Code]
Arm System with No Entry Delay
STAR MENU:
The Star Menu on the IQ Keypad allows access to more advanced functionality such as silent arming, bypassing
zones, turning on/off the chime, buzzer and more. See table below for a list of functions
NOTE: All * menus will follow secure arming option whether an access code is needed or not
Key
Description
Press and hold both the 1 & 3 keys simultaneously to generate a fire alarm.
Press and hold both the 4 & 6 keys simultaneously to generate an auxiliary
emergency alarm.
Press and hold both the 7 & 9 keys simultaneously to generate a police panic alarm.
EMERGENCY KEYS:
Emergency keys allow you to trigger an emergency panic directly from the IQ Keypad.
NOTE: Press and hold emergency keys for two seconds
PARTITION ARMING:
The Hash Menu on the IQ Keypad allows access to Partition Arming functionality. It may also act as a “Home”
button to back out of any button press activity and start over. See table below for a list of functions.
Press
Action
[#][1] + [Arm Stay] + [Access Code]
Arm Partition 1 to Stay
[#][2] + [Arm Stay] + [Access Code]
Arm Partition 2 to Stay
[#][3] + [Arm Stay] + [Access Code]
Arm Partition 3 to Stay
[#][4] + [Arm Stay] + [Access Code]
Arm Partition 4 to Stay
[#][1] + [Access Code]
Disarm Partition 1
Hold [#] for 2 Seconds
Cancels any current IQ Keypad activity or button presses
LEGAL
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
RF EXPOSURE STATMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated
with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must
follow the specific operating instructions for satisfying RF exposure compliance.!
ISED CANADA NON-INTERFERENCE DISCLAIMER
This device contains licence-exempt !transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:!
1. This device may not cause interference.!
2. This device must accept any interference, including interference that may cause undesired operation of the
device.!
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).
L’émetteur/récepteur exempt de licence! contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempt de licence. L’exploitation est
autorisée aux deux conditions suivantes :!
1. L’appareil ne doit pas produire de brouillage;!
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.!
Cet appareil numérique de la Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
LEGAL
ISED CANADA RF EXPOSURE STATMENT
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and any part of your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. !
Cet équipement est conforme aux limites d’exposition aux radiations ISED CNR-102 établies pour un environnement
non contrôlé. Une distance de séparation d'au moins 20 cm doivent être maintenue entre l'antenne de cet appareil et
toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Johnson Controls Prox-PG Mode d'emploi

Prox-PG
Johnson Controls
Marque
Johnson Controls
Modèle
Prox-PG
Catégorie
Pavés numériques
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents