SMC EXW1-A1 Manuel utilisateur

Marque: SMC

Modèle: EXW1-A1

Taper: Manuel utilisateur

Vous trouverez ci-dessous de brèves informations concernant EXW1-A1. L'adaptateur sans fil EXW1-A1 est doté d'une capacité de communication sans fil de 2,4 GHz et d'une interface RS485 pour la connexion avec les unités de base/distantes sans fil SMC. Il peut communiquer des données d'entrée/sortie, des diagnostics et autres données. La période de saut de fréquence et le débit de données peuvent être sélectionnés entre 2 ms (1000 kbps) / 5 ms (250 kbps). De plus, les numéros de canaux de fréquence peuvent être sélectionnés entre 15 et 79.

No.DLZ-91028-WN037

PRODUCT NAME

Wireless Adaptor

Certificate Model

EXW1-A1

Product Number

EXW1-A1**

Confidential

SMC Corporation

- 1 -

No.DLZ-91028-WN037

Contents

Introduction 4

Lineup 4

External appearance 4

Connections with Base/Remote units 5

Connector pin assignment 5

Wireless Specification 6

Product Specification 6

- 2 -

No.DLZ-91028-WN037

Caution

Notice:

Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the

equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV technician for help.

This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undesired operation.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This device is authorized under Title 47 CFR 15.519 (the FCC Rules and Regulations).

The operation of this device is subject to the following restriction:

The changes or substitutions of the antennas which are furnished with the device is prohibited.

FCC ID : 2AJE7SMC-WEX08

- 3 -

No.DLZ-91028-WN037

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Caution

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna

or transmitter. Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

"Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of the

device."

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

"This Class B digital apparatus complies with Canadian ICES-003."

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

“This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or

transmitter.”

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnant en conjonction avec une

autre antenne ou transmetteur.

“This equipment should be installed and operated with a minimum distance of 20cm between the radiator

and your body”

Cet équipement doit être installé et utilisé à une distance minimale de 20cm entre le radiateur et votre corps.

- 4 -

No.DLZ-91028-WN037

Introduction

EXW1-A1 is a wireless adaptor which is equipped with 2.4GHz wireless communication capability. And this

product has the RS485 interface for connection with SMC wireless Base/Remote units to communicate the

input/output, diagnostic and other data.

The frequency hopping period and the data rate can be selected between 2ms(1000kbps) / 5ms(250kbps).

Moreover, the frequency channel numbers can be selected from 15 to 79.

Lineup EXW1-A1

Product number

Hardware version

Wireless software

version

Control software

version

EXW1-A11N

Ver.1.0.0

EXW1-A12N

Ver.1.0.0

Ver.2.0.0

EXW1-A13N

Ver.1.0.0

Ver.3.0.0

EXW1-A11N-X1

Ver.1.0.0

Ver.4.0.0

External appearance

LED

- 5 -

No.DLZ-91028-WN037

Connections with Base/Remote units

The wireless adaptor is connected to Base and Remote units via a cable.

Connector pin assignment

M8 4pin Connector

Pin No.

Description

24V

B (RS485)

A (RS485)

- 6 -

No.DLZ-91028-WN037

Wireless Specification

Model

EXW1-A1

Product number

EXW1-A1*N

Frequency range

2.4GHz (2403MHz ~

2481MHz)

Frequency Channel

79ch～15ch

(ch separation min.1MHz)

Protocol

SMC original protocol

Encryption

SMC original encryption

Radio wave type

FHSS

Output level

20dBm eirp

CCA

Adaptive

Modulation

GFSK

Data Rate

1000kbps / 250 kbps

Deviation

250kHz（1000kbps）

/ 62.5kHz（250kbps）

Frequency hopping

period

2ms(1000kbps) /

5ms(250kbps)

Antenna

Sleeve antenna

(4.37dBi)

Product specification

Model

EXW1-A1

Product number

EXW1-A1*N

Wired interface

RS485

Wired data rate

Max. 2Mbps

Cable

Max. 2.95m

Communication distance

100m

Ambient operating temperature

-10 to +50oC

Ambient storage temperature

-20 to +60oC

Ambient humidity

35 to 85% RH (no condensation)

Power supply voltage

12~24 VDC 10%

Current consumption

50m A

- 7 -

No.DLZ-91028-WN037

Revision history

4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN

Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362

URL http://www.smcworld.com

Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.

SMC EXW1-A1 Manuel utilisateur

Marque: SMC

Modèle: EXW1-A1

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: SMC EXW1-A1 User manual

SMC EXW1-A1 Manuel utilisateur

SMC EXW1-A1 Manuel utilisateur

dans d''autres langues

Autres documents