Unbranded R6GD 3 - 5 Ton, 3 Phase Guide d'installation

Marque: Unbranded

Modèle: R6GD 3 - 5 Ton, 3 Phase

Taper: Guide d'installation

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being able to install the product according

to strict safety guidelines and instructing the customer on how to operate and maintain the equipment for the life of the product.

Safety should always be the deciding factor when installing this product and using common sense plays an important role as

well. Pay attention to all safety warnings and any other special notes highlighted in the manual. Improper installation of the unit

or failure to follow safety warnings could result in serious injury, death, or property damage. These instructions are primarily

intended to assist qualiﬁed individuals experienced in the proper installation of this appliance. Some local codes require

licensed installation/service personnel for this type of equipment. After completing the installation, return these instructions to

the customer’s package for future reference.

WARNING:

DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

FIRE OR EXPLOSION HAZARD



















WHAT TO DO IF YOU SMELL GAS



















13 SEER



R6GD SERIES

Premium Model Shown

USER’S MANUAL & INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INFORMATION ..........................4

OPERATING INSTRUCTIONS ........................................4

Cooling Operation ........................................................4

Heating Operation ........................................................4

Turning the Air Conditioner Off ....................................4

Operating the Indoor Blower Continuously ..................4

AIR CONDITIONER MAINTENANCE .............................4

TROUbLESHOOTING ....................................................4

WARRANTY INFORMATION

A warranty certiﬁcate with full details is included with the

Air Conditioner. Carefully review these responsibilities with

your dealer or service company. The manufacturer will not

be responsible for any costs found necessary to correct

problems due to improper setup, improper installation,

adjustments, improper operating procedure on the part

of the user, etc. Some speciﬁc examples of service calls

which are not included in the limited warranty are:

• Correcting wiring problems in the electrical circuit

supplying the Air Conditioner.

• Resettingcircuitbreakersorotherswitches.

• Adjustingorcalibratingofthermostat.

USER INFORMATION

IMPORTANT SAFETY INFORMATION ..........................5

REQUIREMENTS & CODES ..........................................6

GENERAL INFORMATION .............................................7

Before You Install this Unit ...........................................7

Locating the Equipment ...............................................7

Heating Load ...............................................................7

CombustionAirRequirements ....................................7

VentingRequirements .................................................8

Circulating Air Supply ..................................................10

Air Ducts ............................................................. 10

AirFilterRequirements ....................................... 10

Unconditioned Spaces ......................................... 10

Acoustical Duct Work ........................................... 11

UNIT INSTALLATION .....................................................11

PackagingRemoval .....................................................11

Rigging&Hoisting ........................................................11

Clearances to Combustible Materials ..........................11

Ground Level ................................................................11

Rooftop .........................................................................11

Condensate Drain .......................................................11

Horizontal to Downﬂow Conversion .............................11

RemovalofInternalFilterRack ....................................12

InstallingFiltersintheFilterRack ................................12

RemovingFiltersfromtheFilterRack ..........................12

ELECTRICAL WIRING ....................................................13

Pre - Electrical Checklist ..............................................13

Line Voltage .................................................................13

Grounding .....................................................................14

Thermostat / Low Voltage Connections .......................14

Checking Heat Anticipator Settings ...................... 15

Optional Outdoor Thermostat ............................... 15

Blower Speed ....................................................... 15

Unbalanced 3-Phase Supply Voltage ................... 15

Optional Humidistat .............................................. 16

GASSUPPLY&PIPING ...............................................16

Leak Check ..................................................................17

High Altitude Conversion..............................................17

Lp/Propane Gas Conversion .......................................17

STARTUP & ADJUSTMENTS ........................................18

Pre - Start Checklist .....................................................18

Start-up Procedure .......................................................18

Air Circulation ....................................................... 18

System Cooling .................................................... 18

System Heating .................................................... 18

Verifying&AdjustingTemperatureRise ......................18

Verifying&AdjustingFiringRate .................................19

Verifying Operation of Over-Temperature

Limit Control .................................................................19

Verifying Burner Operation ...........................................19

RefrigerantCharging ....................................................19

Manifold Pressure Adjustment .....................................20

OPERATING SEQUENCE ..............................................20

Heating Mode ...............................................................20

Cooling Mode ...............................................................21

Fan Mode .....................................................................21

EQUIPMENT MAINTENANCE ........................................21

Cleaning of Heat Exchanger ........................................22

Cleaning of Burners .....................................................22

COMPONENT FUNCTIONS ...........................................23

TROUbLESHOOTING ....................................................23

REPLACEMENT PARTS .................................................23

FIGURES & TAbLES ......................................................24

Figure10.R6GDDimensions .............................. 24

Table9.CenterofGravity&ShippingWeights ..... 24

Airﬂow Information .......................................................25

Table10.NominalAirowRates&TempRises ... 25

Gas Information ............................................................26

Table 11. Gas Pipe Capacities ............................. 26

Table12.GasFlowRates .................................... 26

Figure11.R6GDGasValveLabel ....................... 27

Electrical Information....................................................28

Figure 12. Wiring Diagram for 208/230 V Units .... 28

Figure 13. Wiring Diagram for 460 V Units ........... 29

R6GDChargingCharts ................................................30

Figure 14. Charging Chart for 3 Ton Units ............ 30

Figure 15. Charging Chart for 4 Ton Units ............ 30

Figure 16. Charging Chart for 5 Ton Units ............ 31

FRENCH TRANSLATIONS .............................................32

 ............36

INSTALLER INFORMATION















IMPORTANT SAFETY INFORMATION

Safety markings are used frequently throughout this

manual to designate a degree or level of seriousness and

should not be ignored. WARNING indicates a potentially

hazardous situation that if not avoided, could result in

personal injury or death. CAUTION indicates a potentially

hazardous situation that if not avoided, may result in minor

or moderate injury or property damage.

OPERATING INSTRUCTIONS

NOTE: Thermostat styles vary. Some models may not

include the AUTO mode and others will have the AUTO

in place of the HEAT and COOL. Others may include all

three. Please refer to the thermostat manufacturer’s User

manual for detailed programming instructions.

NOTE: If the temperature level is re-adjusted, or the

system mode is reset, the fan and compressor in the

outdoor unit may not start immediately. A protective timer

circuit holds the compressor and the outdoor fan off for

approximately three minutes following a previous operation

or the interruption of the main electrical power.



1. Set the thermostat’s system mode to COOL or AUTO

and change the fan mode to AUTO. See Figure 1.

2. Set the temperature selector to the desired temperature

level. The outdoor fan, compressor, and blower motor will

all cycle on and off to maintain the indoor temperature

at the desired cooling level.



1. Set the thermostat’s system mode to HEAT or AUTO

and change the fan mode to AUTO. See Figure 1.

2. Set the temperature selector to the desired temperature

level. The compressor, outdoor fan, and blower motor

will cycle on and off to maintain the indoor temperature

at the desired heating level.



Change the thermostat’s system mode to OFF and the fan

mode to AUTO (See Figure 1). NOTE: The system will not

operate, regardless of the temperature selector setting.



The continuous indoor blower operation is typically used to

circulate the indoor air to equalize a temperature unbalance

due to a sun load, cooking, or ﬁreplace operation.

SetthethermostatfanmodetoON(Figure1).Theindoor

blower starts immediately, and will run continually until

the fan mode is reset to AUTO.

The continuous indoor blower operation can be obtained

with the thermostat system mode set in any position,

including OFF.

UNIT MAINTENANCE

Proper maintenance is most important to achieve the best

performance from the appliance and should be performed

frequently at the beginning of each air conditioning season.

WARNING:

     

    





    

     





• Keeptheoutdoorunitclean.Hoseoffperiodicallyand

keep unit ﬁns clear of leaves and grass clippings.

• Keep the outdoor unit clear of obstructions.

DONOTobstructairowwithtallplantsorshrubs.DO

NOTstoregasolineorotherammablematerialsonor

near the outdoor unit.

• Neveroperatetheappliancewithoutalterinstalledin

the return air duct. Inspect ﬁlters frequently and replace

when necessary with ﬁlter of same dimensional size.

TROUbLESHOOTING

If the unit fails to operate, check the following:

• Checkthethermostatsetting.Makesurethesystem

mode and temperature settings are correct.

• Checktheelectricalpanelfortrippedcircuitbreakers.

• Checktheltersfordustaccumulation.

• Checktheoutdoorunitandmakesureitiscleanand

not covered with grass or leaves.

• Iftheitemsabovedon’tresolveyourproblems,then

call your nearest service technician.

USER INFORMATION

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are

used frequently throughout this manual to designate a

degree or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation that

if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

WARNING:

      

     

      











     

     









WARNING:

    

    

     

      



 



      

     



     













WARNING:

       







     







• TheinstallationmustconformwiththeNationalFuelGas

Code(ANSI2223.1,NFPA-54).Canadianinstallations

mustconformwithCAN/CGA-B149installationcodes.

• The installer must comply with all local codes and

regulations which govern the installation of this type

of equipment. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Consult local building codes and the

NationalElectricalCode(ANSICI)forspecialinstallation

requirements.

• Thisequipmentcontainsliquidandgaseousrefrigerant

under high pressure. Installation or servicing should only

be performed by qualiﬁed trained personnel thoroughly

familiar with this type equipment.

WARNING:

    





      

     





CAUTION:







WARNING:









WARNING:



      

     





INSTALLER INFORMATION

• Allelectricalwiringmustbecompletedinaccordance

with local, state and national codes and regulations

andwiththeNationalElectricCode(ANSI/NFPA70)

or in Canada the Canadian Electric Code Part 1 CSA

C.22.1.

• Air Ducts must be installed in accordance with the

standardsoftheNationalFireProtectionAssociation

“Standards for Installation of Air Conditioning and

Ventilation Systems” (NFPA 90A), “Standard for

InstallationofResidenceTypeWarmAirHeatingandAir

ConditioningSystems”(NFPA90B),theseinstructions,

and all applicable local codes.

• Installthisunitonlyinalocationandpositionasspecied

on page 7. This unit is designed only for outdoor

installations and should be located with consideration

of minimizing the length of the supply and return ducts.

Consideration should also be given to the accessibility of

fuel, electric power, service access, noise, and shade.

• Before beginning the installation, verify that the unit

model is correct for the job. The unit model number

is printed on the data label. Follow all precautions in

the literature, on tags, and on labels provided with

the equipment. Read and thoroughly understand

the instructions provided with the equipment prior to

performing the installation and operational checkout of

the equipment.

• Useonlywiththetypeofgasapprovedforthisunit.

Refertotheunitratingplate.

• Provideadequatecombustionandventilationairtothe

unit. See pages 7 - 9.

• Provideadequateclearancesaroundtheairventintake

terminal. See page 8.

• Combustion products must be discharged outdoors.

Connect this unit to an approved vent system only, as

speciﬁed on page 8.

• Never test for gas leaks with an open ame. Use

a commercially available soap solution to check all

connections (See page 17).

• ConsultTable10(page25),andtheratingplateforthe

proper circulating air ﬂow and temperature rise. It is

important that the duct system be designed to provide

the correct ﬂow rates and external pressure rise. An

improperly designed duct system can result in nuisance

shutdowns, and comfort or noise issues.

• Installationofequipmentmayrequirebrazingoperations.

Installer must comply with safety codes and wear

appropriate safety equipment (safety glasses, work

gloves, ﬁre extinguisher, etc.) when performing brazing

operations.

• ThisequipmentisNOT to be used for temporary heating

of buildings or structures under construction.

REQUIREMENTS & CODES

       

   



      



CGA b149.1.

Additional codes listed below are for reference purposes

only and do not necessarily have jurisdiction over local or

state codes. Local codes and regulations take precedence

over any recommendations contained in these instructions.

Always consult with local authorities before installing any

gas appliance.



• US:NationalFuelGasCode(NFGC),AirforCombustionand

Ventilation

• CANADA: Natural Gas and Propane Installation Codes

(NSCNGPIC),VentingSystemsandAirSupplyforAppliances



• USandCANADA:AirConditioningContractorsAssociation

(ACCA) Manual D, Sheet Metal and Air Conditioning

ContractorsNationalAssociation(SMACNA),orAmerican

Society of Heating, Refrigeration, and Air Conditioning

Engineers(ASHRAE)FundamentalsHandbook



• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1



• US:NFGCandNationalPlumbingCodes

• CANADA:NSCNGPIC



• US:Current edition of the NFGC and the NFPA 90B.For

copies,contacttheNationalFireProtectionAssociationInc.,

Batterymarch Park, Quincy, MA 02269; or American Gas

Association,400N.Capitol,N.W.,WashingtonDC20001or

www.NFPA.org

• CANADA:NSCNGPIC.Foracopy,contactStandardSales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto),Ontario,M9W1R3Canada



• US:(NFGC)NFPA54–1999/ANSIZ223.1andtheInstallation

Standards, Warm Air Heating and Air Conditioning Systems

ANSI/NFPA90B.

• CANADA:CAN/CGA-B149.1and.2–M00NationalStandard

ofCanada.(NSCNGPIC)

GENERAL INFORMATION

TheR6GDSinglePackageGasHeating/ElectricCooling

Unit is designed only for outdoor rooftop or ground level

installations and can be readily connected to the high

static duct system of a home. This unit has been tested

for capacity and efciency in accordance with A.R.I.

Standards and will provide many years of safe and

dependable comfort, providing it is properly installed

and maintained. With regular maintenance, this unit will

operate satisfactorily year after year. Abuse, improper

use, and/or improper maintenance can shorten the life

of the appliance and create unsafe hazards.

To achieve optimum performance and minimize equipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain tools

and mechanical skills.



√ The cooling load of the area to be conditioned must be

calculated and a system of the proper capacity selected.

It is recommended that the area to be conditioned be

completely insulated and vapor sealed.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. Consideration should be

given to availability of electric power, service access,

noise, and shade. If there is any question concerning

the power supply, contact the local power company.

√ All units are securely packed at the time of shipment and

upon arrival should be carefully inspected for damage

prior to installing the equipment at the job site. Verify

coil ﬁns are straight. If necessary, comb ﬁns to remove

ﬂattened or bent ﬁns. Claims for damage (apparent or

concealed) should be ﬁled immediately with the carrier.

√ Survey the job site to determine the best location for

mounting the outdoor unit. Choose an appropriate

location that minimizes the length of the supply and

return air ducts.

√ The indoor unit (air handler, furnace, etc) should be

installed before routing the refrigerant tubing. Refer

to the indoor unit’s instruction manual for installation

details.

√ Please consult your dealer for maintenance information

and availability of maintenance contracts. Please read

all instructions before installing the unit.



• Selectasolid,levelposition,preferablyonaconcrete

slab, slightly above the grade level, and parallel to the

home. DO NOT PLACE UNIT UNDER THE HOME.

• Overhead obstructions, poorly ventilated areas, and

areas subject to accumulation of debris should be

avoided. Do not place the unit in a conﬁned space or

recessed area where discharge air from the unit to re-

circulate into the condenser air inlet, through the coil.

• Sufcientclearanceforunobstructedairowthroughthe

louvered control access panel and outdoor coil must be

maintained in order to achieve rated performance. See

Figure 2 for minimum clearances to obstructions.

• Aclearanceofatleast36inchesfromthebloweraccess

panel and from the louvered control access panel is

recommended for servicing and maintenance. 







• Thehotcondenserairmustbedischargedupandaway

from the home, and if possible, in a direction with the

prevailing wind.

• Ifpractical,placetheairconditioneranditsductsinan

area where they will be shaded from the afternoon sun,

when the heat load is greatest.



This unit should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

Contractors of America (Manual J); American Society of

Heating,Refrigerating,andAirConditioningEngineers;

or other approved engineering methods. For installations

above 2,000 ft., the unit should have a sea level input

rating large enough that it will meet the heating load after

deration for altitude.

COMbUSTION AIR REQUIREMENTS

WARNING:











Provisions must be made during the installation of this

unit that provide an adequate supply of air for combustion.

• Instructions for determining the adequacy of an

installation can be found in the current revision of the

NFGC(ANSIZ223.1/NFPA54).

. These requirements are for

USinstallationsasfoundintheNFGC.

• TherequirementsinCanada(B149.1)arestructured

differently. Consult with B149.1 and local code ofﬁcials

for Canadian installations.

Air openings in the door of the unit, warm air registers, and

return air grilles must never be restricted. If the unit does

not receive an adequate supply of air for combustion, the

ﬂame roll-out control located above the burners will open,

turning off the gas supply to the burners. This safety device

is a manually reset switch. IMPORTANT NOTE: DO NOT





.

If this control must be replaced, use only factory authorized

replacementparts.SeetheReplacementPartsListon

page 23.

control area of this unit. 



The following list summarizes the requirements for the

location of the vent system termination:

• Thelocationoftheventterminationmustbeconsistent

withtheNationalFuelGasCode(ANSIZ223.1)orCAN/

CGA-B149 Installation Codes.

• Theventterminationmustbelocatedatleast4feet

horizontally from any electric meters, gas meters,

regulators, and relief equipment.

• Theventterminationmustbelocatedatleast3feet

above any forced air inlet located within 10 feet.

• Theventterminationmustbelocatedatleast4feet

below, 4 feet horizontally from, or 1 foot above any

door, window, or gravity air inlet into any building.

• Theventterminationmustbelocatedatleast1foot

above grade.

• Theunitshouldbeinstalledinawaythatpreventsany

obstruction of the vent termination during accumulating

snow.

• Theunitinstallationshallavoidareaswherecondensate

drainage may cause problems by dropping on planters

or patios, etc. Also verify exhaust gases will not

impinge on windows or building surfaces, which may

be compromised or damaged by condensation.

• Donotinstalltheunitsuchthatexhaustfromthevent

termination is directed into window wells, stairwells,

under decks, or in alcoves or similarly recessed areas.

The vent termination must not be located above any

public walkways.

Figure 3 shows the proper installation of the vent cover

assembly over the vent outlet on the exterior of the corner

panel. The fasteners used to secure the vent cover

assembly have been included in the owner’s package.

WARNING:

       



      



To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use clean air from outside.







•Gasoline/Kerosene

•Permanentwavesolutions

•Chlorinatedwaxesandcleaners

•Chlorinebasedswimmingpoolchemicals

•Watersofteningchemicals

•De-icingsaltsorchemicals

•Carbontetrachloride

•Halogentyperefrigerants

•Cleaningsolvents

•Cements,glues,paintremovers,varnishes,etc.

•Hydrochloricacid

•Masonryacidwashingmaterials

•PlumbingStack



This unit has been equipped with an integral venting

system and designed to operate only with this venting

system.Noadditional ventingshall beused.This unit

must be vented to the outdoors.

WARNING:

      





A vent cover assembly has been supplied with the unit.

and can be found secured to the gas controls within the



Minimum Required

Clearances to Combustibles

36"

TOP OF UNIT

TO BE

UNOBSTRUCTED

See Note 1

See Note 2

NOTE 1: 6” When coil is present on duct side.

NOTE 2: 1” When no coil is present on duct side.



WARNING: 

CARbON MONOXIDE POISONING HAZARD

      



     



      



     





      













      









      







      



 



      



     

    





      

      

















      

     





     



RISQUE D’EMPOISONNEMENT AU

MONOXYDE DE CARbONED





     



      

     













     

     

       

    



    

















       

       





















      





        

    



       



b149.1.

      

  





      





CIRCULATING AIR SUPPLY

WARNING:























   



         

















Air Ducts

This unit is designed only for use with a supply and return

duct. Air ducts should be installed in accordance with the

standards of the National Fire Protection Association

“Standard for Installation of Air Conditioning Systems”

(NFPA90A),“StandardforInstallationofResidenceType

WarmAirHeatingandAirConditioningSystems”(NFPA

90B),andallapplicablelocalcodes.NFPApublications

are available by writing to: National Fire Protection

Association, Batterymarch Park, Quincy, ME 02269 or

visitwww.NFPA.orgontheweb.

• DesigntheductworkaccordingtoManualDbytheAir

Conditioning Contractors of America (ACCA).

• Theductsmustbeproperlysizedandnotexceed0.2”

W.C. pressure drop at 400 scfm per nominal ton of

cooling capacity.

• Ductworkshouldbeattacheddirectlytotheunitanges

for horizontal applications.

• Ifroofcurbisinstalled,theductsmustbeattachedto

the curb hangers, not the unit.

• It is recommended that the outlet duct be provided

with a removable access panel. The opening should

be accessible when the unit is installed in service and

shall be sizes so that smoke or reﬂected light may be

observed inside the casing to indicate the presence of

leaks in the heat exchanger. The cover for the opening

shall be attached in a way that will prevent leaks.

• If outside air is utilized as return air to the unit for

ventilation or to improve indoor air quality, the system

must be designed so that the return air to the unit is not

less than 50° F (10° C) during heating operation.

• Ifacombinationofindoorandoutdoorairisused,the

ducts and damper system must be designed so that the

return air supply to the furnace is equal to the return air

supply under normal, indoor return air applications.

AirFilterRequirements

WARNING:









• A suitable air ﬁlter must be installed upstream of the

evaporatorcoilofthereturnairsystem.RefertoTable

1 for recommended ﬁlter sizes.

• All return air must pass through the ﬁlters before entering

the evaporator coil. It is important that all ﬁlters be kept

clean and replaced frequently to ensure proper operation

of unit. Dirty or clogged ﬁlters will reduce the efﬁciency

of the unit and result in unit shutdowns.

• Air ﬁlter pressure drop must not exceed 0.08 inches WC.

• DownowInstallationsrequireaninternallteraccessory

kit to be installed.

• HorizontalInstallationsrequiretheairltersystembe

installed in the return air ductwork.

NOTE TO INSTALLER: After installing or replacing the

ﬁltration system for this unit, add the following statement

on or adjacent to the ﬁlter service panel: 







NOMINAL

COOLING



APPROXIMATE

AIR FLOW



APPROXIMATE

FILTER AREA



RECOMMENDED

FILTER SIZE



3.0 1,100 - 1,300 625 25 x 25

4.0 1,400 - 1,800 850 18 x 24 (2 required)

5.0 1,800 - 2,200 1,000 20 x 25 (2 required)

* Based on velocity of 300 ft/min for disposable ﬁlters and 500 ft/min

for high velocity (cleanable) Filters.

Unconditioned Spaces

All duct work passing through unconditioned space must

be properly insulated to minimize duct losses and prevent

condensation. Use insulation with an outer vapor barrier.

Refertolocalcodesforinsulationmaterialrequirements.

Acoustical Duct Work

Certain installations may require the use of acoustical

lining inside the supply duct work.

• Acousticalinsulationmustbeinaccordancewiththe

current revision of the Sheet Metal and Air Conditioning

ContractorsNationalAssociation(SMACNA)application

standard for duct liners.

• DuctliningmustbeULclassiedbattsorblanketswith

a ﬁre hazard classiﬁcation of FHC-25/50 or less.

• Fiberductworkmaybeusedinplaceofinternalduct

liners if the ﬁber duct work is in accordance with the

currentrevisionoftheSMACNAconstructionstandard

on ﬁbrous glass ducts. Fibrous duct work and internal

acousticalliningmustbeNFPAClass1airductswhen

tested per UL Standard 181 for Class 1 ducts.

UNIT INSTALLATION



Remove the shipping carton and User’s Manual from

the equipment. Take care not to damage the tubing

connections when removing the carton. For rooftop

installations, remove and discard the two supports attached

beneath the unit.



WARNING:









 



 



 



 







       





R6GD units are certied as combination heating and

cooling equipment for outdoor rooftop or ground level

installations. Units may be installed on combustible

ﬂooring or Class A, B, or C rooﬁng material when used

with bottom supply and return air ducts as long as the

following requirements are met:

• If using horizontal supply and return air ducts, the

horizontal roof curb kit and return air kit must be installed

prior to unit installation. Horizontal roof curb is required.

• Ifusingbottomdischargewithreturnairductsaroofcurb

mustbeinstalledpriortounitinstallation.SeeRigging

and Hoisting section for setting of the unit.

• Sufcient clearance forunobstructed airowthrough

the outdoor coil must also be maintained in order to

achieve rated performance. See page 7 for information

about locating the equipment.



Ground level installations must be located according to

local building codes or ordinances and these requirements:

• Clearancesmustbeinaccordancewiththoseshown

in Figure 2 (page 7).

• Asuitablemountingpad(Figure4,page12)mustbe

provided and be separate from the building foundation.

The pad must be level to ensure proper condensate

disposal and strong enough to support the unit’s weight.

The slab height must be a minimum of 2” (5cm) above

grade and with adequate drainage.

• Unitsrequirehorizontalroofcurbandreturnairkitfor

horizontal installations.

• Ductwork should be attached directly to anges on

panels supplied in horizontal duct conversion kits.



Rooftopinstallationsmustbelocatedaccordingtolocal

building codes or ordinances and these requirements:

• Theroofmustbecapableofhandlingtheweightofthe

unit.Forunitweights,seeTable9.Reinforcetheroof

if necessary.

• Theappropriateaccessoryroofcurb(Figure5,page12)

must be installed prior to unit installation. The roof curb

must be square and level to ensure proper condensate

drainage.     



• Secure roof curb or frame to roof using acceptable

mechanical methods per local codes. NOTE: Make sure

the two supports beneath the unit have been removed.



Condensate is removed from the unit through the 3/4”

female pipe ﬁtting (Figure 6, page 12) located on the front

side of the unit. Install a 2 inch condensate trap in the

drain line of the same size and prime with water. When

connecting rigid drain line, hold the female ﬁtting with a

wrench to prevent twisting. Refer

to local codes and restrictions for proper condensate

disposal requirements.



The unit is shipped ready for horizontal duct connections.

If down ﬂow ducts are required, the unit must be converted

following the steps below for both the supply and return

ducts.

1.Removethehorizontalductcap.

2. Locate the duct cap inside the duct openings and remove

the screw holding it in place.

3. Lift the cap out of the unit. (The cap can be pushed

up from the bottom by reaching through the fork slot).

4. Cover the horizontal duct opening with the horizontal

duct cap. The insulation will be on the indoor side.

5. Fasten the cover with screws to seal.





1.Removethereturnairpanelfromtheunit.

2.Removetheheightadjustmentscrewfromtheinside

of the rack.

3.Remove(1)screwsecuringtheassemblytothecoil

located on the left leg of the rack. NOTE: The assembly

can now be easily collapsed and removed from the unit.

See Figure 7 for ﬁlter rack securing screw locations.

Condensate Drain







UNIT SIZE INTERNAL FILTER SIZE

R6GD-X36

(2) 16” x 25” x 1”

(2) 16” x 25” x 2”

R6GD-X48/X60

(2) 18” x 25” x 1”

(2) 18” x 25” x 2”







1.Removeaccesspanelscrewsfromreturnairpanel.

(HINT: Loosen the unit’s top panel screws near the

top edge of the access panel. The access panel was

designed to be captured underneath the top panel.)

2. Slide the ﬁrst ﬁlter between both guide channels of ﬁlter

rack and allow the ﬁlter to drop easily into place.

3. Verify the bottom of the ﬁlter is within the channels of

the rack.

4. Slide the 2nd ﬁlter between both guide channels of ﬁlter

rack.

5. Verify the bottom of the ﬁlter is within the channels of

the rack.

6.Replaceaccesscoverbyslidingthetopedgeofpanel

under the lip of the unit’s top panel. Secure access

panel by replacing the screws.





1.Removeaccesspanelscrewsfromreturnairpanel.

( Loosen the unit’s top panel screws near the

top edge of the access panel. The access panel was

designed to be captured underneath the top panel.)

2.Removeupperlterbygentlypullinglterthroughthe

access panel opening.

3.Removelowerlterbyliftingmediatotopoflterrack.

Removeinthesamemannerasdescribedinstep2.

4. Install new ﬁlter in the ﬁlter rack as described in the

previous section.

Securing

Screws



ELECTRICAL WIRING

WARNING:









      

      



• Allelectricalconnectionsmustbeincompliancewith

all applicable local codes and ordinances, and with

the current revision of the National Electric Code

(ANSI/NFPA70).

• ForCanadian installations theelectricalconnections

and grounding shall comply with the current Canadian

Electrical Code (CSA C22.1 and/or local codes).



√ Verify the voltage, frequency, and phase of the supply

source match the speciﬁcations on the unit rating plate.

√ Verify that the service provided by the utility is sufﬁcient

to handle the additional load imposed by this equipment.

See Table 3 or the unit wiring label for proper high and

low voltage wiring.

√ Verify factory wiring is in accordance with the unit wiring

diagram (Figures 12 - 13, pages 28 - 29). Verify none of

the connections loosened during shipping or installation.



• Thelinevoltagetotheunitshouldbesuppliedfroma

dedicated branch circuit containing the correct fuse or

circuit breaker for the unit.

• 

 This switch shall

be capable of electrically de-energizing the outdoor unit.

See unit data label for proper incoming ﬁeld wiring. Any

other wiring methods must be acceptable to authority

having jurisdiction.

• Useonlycopperwireforthelinevoltagepowersupply

to this unit (Table 4, page 14). Use proper code agency

listed conduit and a conduit connector for connecting

the supply wires to the unit. Use of rain tight conduit is

recommended.

• Providepowersupplyfortheunitinaccordancewith

the unit wiring diagram and the unit rating plate.

• Overcurrentprotectionmustbeprovidedatthebranch

circuit distribution panel and sized as shown on the unit

rating label and according to applicable local codes.

See the unit rating plate for maximum circuit ampacity

and maximum overcurrent protection limits.

• Awiringdiagramislocatedontheinsidecoverofthe

control access panel of the outdoor unit. The installer

should become familiar with the wiring diagram before

making any electrical connections to the outdoor unit.

See Figures 12 - 13.

• Ifanyoftheoriginalwiressuppliedwiththeunitmust

be replaced, they must be replaced with material of the

same gauge and temperature rating.

• Unitsareshippedfromthefactorywiredfor240volt

transformer operation. For 208V operation, remove the

lead from the transformer terminal marked 240V and

connect it to the terminal marked 208V. Three phase,

460V units are shipped wired for 460V operation.

• Internallymountedcircuitbreakersareavailableaseld

installed options. These circuit breakers can be used

as an electrical disconnect.

• Connecttheline-voltageleadstotheterminalsonthe

contactor (or the circuit breaker if the ﬁeld installed circuit

breaker kits are used) inside the control compartment.

















 























  RLA LRA

R6GD-X36C

72,000 208/-230/60/3 187 253 11.6 73.0 1.2 4.1 21.2 30

96,000 208/-230/60/3 187 253 11.6 73.0 1.2 4.1 21.2 30

R6GD-X48C

96,000 208/-230/60/3 187 253 15.3 83.1 1.2 6 27.7 40

120,000 208/-230/60/3 187 253 15.3 83.1 1.2 6 27.7 40

R6GD-X60C

96,000 208/-230/60/3 187 253 17.4 110.0 1.2 7.6 31.9 45

120,000 208/-230/60/3 187 253 17.4 110.0 1.2 7.6 31.9 45

R6GD-X36D

72,000 460/60/3 414 506 6.4 38 0.6 2.1 12.1 15

96,000 460/60/3 414 506 6.4 38 0.6 2.1 12.1 15

R6GD-X48D

96,000 460/60/3 414 506 6.9 41 0.6 3.2 13.8 20

120,000 460/60/3 414 506 6.9 41 0.6 3.2 13.8 20

R6GD-X60D

96,000 460/60/3 414 506 8.6 52 0.6 4.0 16.7 25

120,000 460/60/3 414 506 8.6 52 0.6 4.0 16.7 25

FLA=FullLoadAmps;LRA=LockRotoramps;RLA=RatedLoadAmps.



Voltage unbalance occurs when the voltages of all phases

of a 3-phase power supply are no longer equal. This

unbalance reduces motor efﬁciency and performance.

Some underlying causes of voltage unbalance may

include: Lack of symmetry in transmission lines, large

single-phase loads, and unbalanced or overloaded

transformers. A motor should never be operated when a

phase imbalance in supply is greater than 2%.

Perform the following steps to determine the percentage

of voltage imbalance:

1. Measure the line voltages

of your 3-phase power

supply where it enters

the building and at a

location that will only

be dedicated to the

unit installation. (at the

units circuit protection or

disconnect).

EXAMPLE:

AB = 451V

BC = 460V

AC = 453V

2. Determine the average voltage in the power supply.

In this example, the measured line voltages were 451,

460, and 453. The average would be 454 volts (451 +

460 + 453 = 1,364 / 3 = 454).

3. Determine the maximum deviation:

EXAMPLE

From the values given in step 1, the BC voltage (460V)

is the greatest difference in value from the average:

460 - 454 = 6

454 - 451 = 3

454 - 453 = 1

4. Determine percent of

voltage imbalance by

using the results from

steps2&3inthefollowing

equation.

454

100 x

= 1.32%

EXAMPLE

maxvoltage deviation

fromaverage voltage

=100 x

averagevoltage

% Voltage Imbalance

The amount of phase imbalance (1.32%) is satisfactory

since the amount is lower than the maximum allowable

2%. Please contact your local electric utility company if

your voltage imbalance is more than 2%.



WARNING:





 



This unit must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

theNationalElectricalCode(ANSI/NFPA70)ortheCSA

C22.1 Electrical Code. Use the grounding lug provided in

the control box for grounding the unit.



• TheR6GDunitisdesignedtooperatefroma24VAC

Class II control circuit. The control circuit wiring must

complywiththecurrentprovisionsoftheNEC(ANSI/

NFPA 70) and with applicable local codes having

jurisdiction. Thermostat connections should be made

in accordance with the instructions supplied with the

thermostat and the indoor equipment.

• The low voltage wires must be properly connected.

Route24Vcontrolwiresthroughthesealinggrommet

nearthepowerentrance.Recommendedwiregauge

and wire lengths for typical thermostat connections are

listed in Table 5.

• Several thermostat options are available depending

on the accessories installed with the unit. Select a

thermostat that operates in conjunction with the installed

accessories.

• Back-upfossilfuelheatcapabilityisrequiredwiththe

Dual Fuel iHybrid™ heat pump packaged system. This

system is capable of providing two stages of cooling, two

stages of heating in heat pump mode, and an additional

two stages of secondary gas heating.

• Thethermostatshouldbemountedabout5feetabove

theooronaninsidewall.DONOTinstallthethermostat

on an outside wall or any other location where its

operation may be adversely affected by radiant heat from

ﬁreplaces, sunlight, or lighting ﬁxtures, and convective

heat from warm air registers or electrical appliances.

Refertothethermostatmanufacturer’sinstructionsheet

for detailed mounting information.

Checking Heat Anticipator Settings

• Addthecurrentdrawofthesystemcomponents.

• MeasurethecurrentowonthethermostatR-W circuit

after the circulating blower motor has started. Set the heat

anticipator according to the thermostat manufacturer’s

instructions for heat anticipator settings.

Optional Outdoor Thermostat

If two stage heating is desired, an outdoor thermostat

can be installed in the ﬁeld with 2-stage electric heat. To

install the outdoor thermostat, remove the orange wire

from the E terminal on the terminal block, and connect

to the outdoor thermostat. Connect the other side of the

outdoor thermostat to W2 from the thermostat.





Gas

Valve

Economizer

Plug

Indoor

Thermostat

Sub-Base

Furnace

Board

(Optional, Check

thermostat Instructions)

Optional Commercial Thermostat Only

(Occupied / unoccupied - If Equipped)

Green

Gray

Black

Yellow

White

Blue



The blower speed is preset at the factory for operation at

the same speed for heating and cooling. These factory

settings are listed in Table 10 (page 25). For optimum

system performance and comfort, it may be necessary

to change the factory set speed.

CAUTION:

      

        





1. Shut off all electrical power to the unit and remove the

blower panel. Locate the orange, red and blue wires

terminated to the blower motor. NOTE: The orange wire

controls cooling operation while the red wire controls

heating operation. The blue wire controls fan-only

operation.

2. Verify the required speed from the airﬂow data found in

Table 10. Place appropriate wire on the correct motor

speed tap for the required airﬂow point.

3. The integrated furnace control can be set to a 2 or 3

speed mode. When a G only call is received from the

thermostat (indicating a continuous fan mode), the

blower will run the heating speed when the 

mode is selected using the jumper on the control board

(factory setting). When  mode is selected, the fan

only speed may be different than the heating or cooling

speed. If no jumper is present, the control defaults to the

 mode of operation. A call for heating or cooling

takes priority over fan only mode



An optional humidistat may be installed in the return

air duct for humidity control (when needed), maximum

system capacity and energy efﬁciency. The humidistat

senses when humidity in the return air stream is above

a preset level and sends a signal to the motor to reduce

airﬂow. This allows more moisture to be removed until

the humidity level drops.

NOTE: The packaged heat pump unit is pre-programmed

forhumidistatoperation.Removethejumperconnector

between the two terminals marked HUM on the variable

speed board.

Install the humidistat in the return air duct as directed in

the installation instructions included with the kit. Wire the



COPPER WIRE SIZE — AWG





SUPPLY CIRCUIT

AMPACITY

200 150 100 50

6 8 10 14 15

4 6 8 12 20

4 6 8 10 25

4 4 6 10 30

3 4 6 8 35

3 4 6 8 40

2 3 4 6 45

2 3 4 6 50

2 3 4 6 55

1 2 3 4 60

WireSizebasedonN.E.C.for60°typecopperconductors.

THERMOSTAT

WIRE GAUGE













24 55 25

22 90 45

20 140 70

18 225 110





WARNING:

FIRE OR EXPLOSION HAZARD





       

     







After the gas piping to the unit is complete, all connections

must be tested for gas leaks. This includes pipe connections

at the main gas valve, emergency shutoff valve and

other gas connectors. A soap and water solution can be

applied on each joint or union using a small paintbrush.

If any bubbling is observed, the connection is not sealed

adequatelyandmustberetightened.Repeatthetightening

and soap check process until bubbling ceases.

• 







• 





Ground

Joint

Union

Dripleg

Shut-Off Valve

with

/8 NPT

plugged tap

Burner

Assembly

Manifold

Some utilities

require Shut-Off

Valve to be

4 to 5 feet

above floor

Automatic Gas Valve

(with manual shut-off)



humidistat through the low-voltage wire entrance in the

packaged heat pump unit to the quick-connect terminals

(marked  Wire the humidistat to open on rise in

humidity.

CAUTION:

      

      

 



Check all factory wiring to the units wiring diagram. Inspect

the factory wiring connections to be sure none loosened

during shipping or installation.

GAS SUPPLY & PIPING

 









 







        

    



 

       

     



 



 



 





 









 



This unit only has right side gas entry. When connecting

the gas, provide clearance between the gas supply line

and the entry hole in the unit’s casing to avoid unwanted

noise and/or damage to the unit. A typical gas service

hookup is shown in Figure 8.

Table 11 (page 26) lists gas pipe capacities for standard

pipe sizes as a function of length in typical applications

based on nominal pressure drop in the line.



Conversion of this unit must be performed by qualiﬁed

service personnel, using only approved parts. All

installationsmustbemadeinaccordancewiththeNational

Fuel Gas Code and/or local jurisdiction codes.

WARNING:









     



High altitude conversion can be ﬁeld performed by a

simple adjustment of manifold pressure or a change of

the oriﬁces (if necessary) as described on page 20. The

changes required depend on the installation altitude and

the heating value of the gas (based on sea level) which

can be obtained from your local gas utility. The heating

value of gas at high altitude is always lower than the sea

level heating value. The heating values listed in Tables

6&7(page20)arebasedonsealevelvalues.

If installing this unit above 2,000 feet, the input rate must

be reduced 4% per 1,000 feet of altitude (Example: 12%

at 3,000 feet, 16% at 4,000 feet, etc). NOTE: Deration is

necessary to compensate for low atmospheric pressure

at high altitudes.

For altitudes between 5,000 and 10,000 feet above sea

level, the unit can be converted by adjusting the furnace

manifold pressure. See Tables 6 or 7 for the correct

manifold pressure settings.



WARNING:

    













Conversion of this equipment to LP/Propane gas must

be made by qualiﬁed service personnel, using approved

factory parts. Conversion to LP can be accomplished by

replacing the natural gas oriﬁces with the appropriate LP/

Propane oriﬁces and then adjusting the manifold pressure

(page 20). Conversion to LP/Propane (sea level and high

altitude) is detailed in the installation instructions provided

with the conversion kit. 

Approved conversion kits are:

• TheUnitedStatesLP/PropaneGasSeaLevelandHigh

AltitudeConversionKitisforLP/propaneconversionin

the United States at altitudes between zero and 10,000

ft. above sea level.

• TheCanadianLP/PropaneGasSeaLevelandHigh

AltitudeConversionKitisforLP/propaneconversions

in Canada at altitudes between zero and 4,500 ft. above

sea level.

For installations between zero and 4,999 ft. above sea

level, a #54 drill size oriﬁce should be used. Installations

5,000 ft. above sea level require a # 55 drill size oriﬁce.

Table 7 (page 20) lists the correct oriﬁce size to use at

different altitudes.

After changing the oriﬁces, it is required that you measure

the gas input rate by clocking the gas meter and using

the local gas heating value. See Verifying and Adjusting

theFiringRatesectiononpage19.

START UP & ADJUSTMENTS



√ Verify the unit is level and allows condensate to drain.

√ Verify all clearance requirements are met and there is

free airﬂow to and from the outdoor coil.

√ Verify that the duct work is sealed to prevent air leakage.

√ Verify that the line voltage power leads are securely

connected and the unit is properly grounded.

√ Verify that the low voltage wires are securely connected

to the correct leads in the low voltage area of the control

box.

√ Verify that the gas line service pressure does not exceed

10.0 inches WC (0.36 psig), and is not less than 4.5

inches WC (0.16 psig) for natural gas. For LP gas the

line service pressure must not exceed 14 inches WC

(0.51 psig) and must not be less than 11.0 inches WC

(0.40 psig).

√ Verify that the ﬂame roll-out control is closed. If

necessary, press the red button to reset the control. DO

NOT install a jumper wire across the control to defeat its

function. If the control reopens upon start-up, DO NOT

reset the control without identifying and correcting the

fault condition which caused the control to trip.

√ Verify that the gas line has been purged and all

connections are leak tight.

√ Verify that all exterior panels are replaced and securely

fastened.

√ Verify that the outdoor fan turns freely.

√ Verify that the power supply branch circuit overcurrent

protection is sized properly.

√ Verify that the thermostat is wired correctly. The

thermostat function switch should be set to OFF and

the thermostat fan switch should be set to AUTO.



WARNING:



       









• Checkallelectricalwiringforlooseconnectionsand

tighten as required.

• Checkunitforreturnairltersandcondensatetrap.

• Closeallelectricaldisconnectstoenergizethesystem.

Air Circulation

Leave the thermostat system mode on OFF, and set the

fanmodetoON.Blowershouldruncontinuously.Check

the air delivery at the supply registers and adjust register

openings for balanced air distribution. Examine ductwork

for leaks or obstruction if insufﬁcient air is detected. Set

the thermostat fan mode to AUTO. The blower should

stop running.

System Cooling

1. Set the thermostat’s system mode to COOL and the

fan mode to AUTO. Gradually lower the thermostat

temperature setpoint below room temperature and verify

the compressor, fan and indoor blower energize.

2. Feel the air being circulated by the indoor blower and

verify that it is cooler than ambient temperature. Listen for

any unusual noises. If unusual sounds occur, determine

the source of the noise and correct as necessary.

3. Allow the cooling system to operate for several minutes

and then set the temperature selector above room

temperature. Verify the fan and compressor cycle off

with the thermostat. NOTE: The blower will also stop

after an 85 - 90 second delay.

System Heating

1. Set the thermostat to the lowest setting.

2. Follow the procedures given on the operating instruction

label, this manual or attached inside the louvered control

access panel.

3. Set the thermostat above room temperature and verify

the Operating Sequence. See page 20.

4. Verify that the compressor and outdoor fan motor are

not energized.

5. After the unit has run for approximately ﬁve minutes,

set the thermostat below room temperature and verify

the shutdown sequence; steps 10 -12 in the Operating

Sequence section (page 20).



Verify the temperature rise through the unit is within the

range speciﬁed on the unit data label. Temperature rises

outside the speciﬁed range could result in premature heat

exchanger failure.

1. Place thermometers in the return and supply air stream

as close to the unit as possible. The thermometer on the

supply air side must be shielded against direct radiation

from the heat exchanger to avoid false readings.

2. Adjust all registers and duct dampers to the desired

position. Run the unit for 10 to 15 minutes before

taking any temperature readings. The temperature

rise is the difference between the supply and return air

temperatures.

NOTE: For typical duct systems, the temperature rise will

fall within the range speciﬁed on the data label (with the

blower speed at the factory recommended setting) shown

in Table 10 (page 25). If the measured temperature rise

falls outside the speciﬁed range, it may be necessary to

change the blower speed. Lowering the blower speed

increases the temperature rise and a higher speed

decreases the temperature rise.

The unit is equipped with a variable speed motor. Speed

selection is made by moving the leads on the blower motor

terminal block. The speed taps for adjusting the motor

speed are shown in the unit wiring diagram or Figures 12

&13(pages28-29).RefertotheBlowerSpeedSection

(page 15) for additional information.

The integrated control starts the circulating air blower

30 seconds after the gas valve is opened. The control is

factory wired to turn the blower motor off 135 seconds

afterthegasvalveisclosed.NOTE:Theheatingblower

off delay is factory set at 90 seconds. An additional 45

second off delay is programmed into the X-13 blower

motor for a total of 135 seconds.



CAUTION:





The ﬁring rate must be veriﬁed for each installation to

prevent over-ﬁring of the furnace. 

. To

determine the ﬁring rate, follow the steps below:

1. Obtain the gas heating value (HHV) from the gas supplier.

2. Shut off all other gas ﬁred appliances.

3. Start the unit in heating mode and allow it to run for at

least 3 minutes.

4. Measure the time (in seconds) required for the gas

meter to complete one revolution.

5. Convert the time per revolution to cubic feet of gas per

hour using Table 13 (page 27).

6. Multiply the gas ﬂow rate in cubic feet per hour by the

heating value of the gas in Btu per cubic foot to obtain

the ﬁring rate in Btu per hour. See Example.

7. Adjust the manifold pressure if necessary. See Manifold

Pressure Adjustment instructions on page 20. For

additional information about elevations above 2,000

:

• Timefor1revolutionofagasmeterwitha1cubic

foot dial = 40 seconds.

• FromTable13,read90cubicfeetgasperhour.

• Localheatingvalueofthegas(obtainedfromgas

supplier) = 1,040 Btu per cubic foot.

• Inputrate=1,040x90=93,600Btuh.

feet, see page 17.





1. Verify the louvered control access panel is in place and

that there is power to the unit.

2. Block the return airﬂow to the unit by installing a close-

off plate in place of or upstream of the ﬁlter.

3. Set the thermostat above room temperature and verify

the units operating sequence (page 20).

NOTE: The over-temperature limit control should turn off

the gas valve within approximately four minutes (exact time

depends on the efﬁciency of the close-off when blocking

the return air). The circulating air and combustion blowers

should continue to run when the over-temperature limit

control switch opens.

3.Removetheclose-offplateimmediatelyaftertheover-

temperature limit control opens. If the unit operates

for more than four minutes with no return air, set the

thermostat below room temperature, shut off power to

the unit, and replace the over-temperature limit control.



WARNING:





1.Removethelouveredcontrolaccesspanelandverify

there is power to the unit.

2. Set thermostat above room temperature and observe

the ignition sequence. NOTE: The burner ﬂame should

carry over immediately between all burners without

lifting off, curling, or ﬂoating. The ﬂames should be blue,

without yellow tips. Make sure the ﬂame is drawn into

the center of the heat exchanger tube. In a properly

adjusted burner assembly, the ﬂame bends down and

to the right at the end of the heat exchanger tube. The

end of the ﬂame will be out of sight around the bend.

3. After validating ﬂame characteristics, set the thermostat

below room temperature and verify the burner ﬂame

extinguishes completely.



WARNING:

      

     







   

















CAUTION:







The system refrigerant charge can be checked and

adjusted through the service ports provided at the front

panel. Use only gauge lines which have a “Schrader”

depression device present to actuate the valve. Draw a

vacuum on gauge lines to remove air before attaching

themtotheserviceportsontheunit.Refrigerantcharging

must be done by qualiﬁed personnel familiar with safe

and environmentally responsible refrigerant handling

procedures.

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and

fanmodesaredescribedbelow.Refertotheeldand

furnace wiring diagrams (Figures 12 or 13, pages 28 - 29).



1. On a call for heat, the thermostat closes and applies

24 VAC to terminal W on the control board.

2. The control board checks for continuity on the 24 VAC

limit control circuit, over-temperature limit switch, ﬂame

rollout switches, and blocked vent switch in series. If an

open limit is detected, the control board will energize

the inducer blower. All other system functions will be

inoperable until the limit circuit closes. While the limit

is open, the red LED will pulse at a rate of 1 blink per

unit time.

3. The furnace control checks for continuity (24 VAC)

across the pressure switch. If the pressure switch is

closed, the heat mode sequence will not continue. If it

remains closed for 10 seconds, the red LED will ﬂash

3 times repetitively until the fault condition clears.

4. The inducer energizes (if pressure switch is open).

5. The pressure switch will close. If the pressure switch

does not close after 10 seconds, the fault LED will ﬂash

2 times and the inducer will continue to run until the

switch is closed.

6. The inducer will pre-purge for 30 seconds and then the

igniter will start its warm-up as follows:

Initial Power up: After 30 seconds of igniter warm-up,

the gas valves (24 VAC) will open. The igniter circuit

will stay energized for 3 seconds after the gas valve

opens.

After Initial Power up: The control has a programmed

adaptive ignition feature which varies the warm-up

period as follows: If ignition is successful the warm-up

is reduced by 3 seconds on each subsequent call for

heat until ignition failure occurs. Upon ignition failure,

the warm-up is increased by 3 seconds on the next try.

If successful, the timing remains ﬁxed at this level. In

general, whenever ignition failure occurs the warm-up

interval is increased by 3 seconds on the next try. And

if successful, it remains there. Minimum and maximum

warm-up time limits are set at 6 and 54 seconds.

7. The furnace control must prove ﬂame via the ﬂame

sensor 5 seconds after the gas valves open. If ﬂame is

sensed, burners are on and the igniter cools off. If no

ﬂame is sensed, the gas valve closes immediately and

the inducer continues to run. A second trial for ignition

(step 6) begins. If no ﬂame is sensed on the ﬁfth try for

ignition, the furnace control is locked and the red LED

will blink 4 times repetitively. The thermostat must be

opened for at least ten seconds to reset the furnace

control after a lock out. Otherwise, the furnace will

attempt another ignition sequence in 1 hour.

8. After the gas valve opens (30 seconds), the blower will

ramp to the selected airﬂow and continues to run.

9. When the thermostat has been satisﬁed, the W terminal

on the integrated control is de-energized.





NATURAL GAS INSTALLATIONS







800 TO 899 900 TO 999 

zero to 1,999 FT

3.5 3.5 3.5

2,000 to 4,999 FT 3.5 3.5 3.5

5,000 to 5,999 FT 3.5 3.5 3.0

6,000 to 7,999 FT 3.5 3.2 2.8

8,000 to 10,000 FT

3.0 2.8 2.5











MANIFOLD

PRESSURE

ORIFICE

SIZE

zero to 1,999 FT

10.0 54

2,000 to 4,999 FT 8.5 54

5,000 to 5,999 FT 10.0 55

6,000 to 7,999 FT 9.0 55

8,000 to 10,000 FT

8.5 55

NOTE: Manifold pressure based on sea level LP heating value

of 2,500 Btu/cu. ft.



The manifold pressure must be set to the appropriate

value for your installation. To adjust the manifold pressure:

1. Obtain the required manifold pressure setting. Use

Table 6 for natural gas or Table 7 for LP/propane gas.

NOTE: The values listed in the tables are based on sea

level values. At higher altitudes, the heating value of gas

is lower than the sea level heating value.

2.Remove the regulator cap. Turn the high fire

adjusting screw clockwise to increase the pressure or

counterclockwise to reduce the pressure.

3.Replace the regulator cap after adjustments are

complete.

La page charge ...

Unbranded R6GD 3 - 5 Ton, 3 Phase Guide d'installation

Marque: Unbranded

Modèle: R6GD 3 - 5 Ton, 3 Phase

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Unbranded R6GD 3 - 5 Ton, 3 Phase Installation guide

Unbranded R6GD 3 - 5 Ton, 3 Phase Guide d'installation

Unbranded R6GD 3 - 5 Ton, 3 Phase Guide d'installation

dans d''autres langues

Documents connexes

Autres documents