LG Electronics LFXS28566D Mode d'emploi

LG Electronics
Marque
LG Electronics
Modèle
LFXS28566D
Catégorie
Réfrigérateurs-congélateurs côte à côte
Taper
Mode d'emploi
53TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
FAQs: Frequently Asked Questions
Q: What are the best temperature settings for my refrigerator and freezer?
A: The default setting for the refrigerator is 37° Fahrenheit (3° Celsius). The default setting for the
freezer is 0° Fahrenheit (-18° Celsius). Adjust these settings as necessary to keep food at desired
temperatures. Milk should be cold when stored on the inner shelf of the refrigerator. Ice cream should
EH¿UPDQGLFHFXEHVVKRXOGQRWPHOWLQWKHIUHH]HU7RVZLWFKWKHGLVSOD\IURP)DKUHQKHLWWR&HOVLXV
press and hold the Freezer and Refrigerator buttons until you hear a beep and the settings in the
display change.
Q: How do I set the refrigerator and freezer temperatures?
A: Continually press the Refrigerator or Freezer button on the control panel until the desired
temperature appears. The numbers will cycle from highest to lowest and then return to the highest
again with continuous pressing.
Q: Why do I hear a buzzing noise from my refrigerator periodically?
A: This may happen if you do not have a water source attached to your refrigerator and the icemaker is
turned on. If you do not have a water source attached to the back of the refrigerator you should turn
the icemaker off.
Q: Why does the icemaker tray look crooked?
A: This is a normal part of the icemaker cycle. The icemaker tray may appear level or with a slight tilt.
The change in position is to assist in the freezing process.
Q:
My refrigerator is powered on and the controls are working, but it’s not cooling and the display
shows “OFF” (see below). What is wrong?
A: The refrigerator is in Demo Mode. This mode disables cooling to save energy while the appliance
is on display in a store. To restore normal operation, press and hold the Refrigerator and Ice Plus
buttons for 5 seconds or until you hear a beep and the temperature settings appear on the display.
Use the same procedure to return the refrigerator to Demo Mode, if desired.
54 TROUBLESHOOTING
Before Calling for Service
5HYLHZWKLVVHFWLRQEHIRUHFDOOLQJIRUVHUYLFHGRLQJVRZLOOVDYH\RXERWKWLPHDQGPRQH\
Cooling
Problem Possible Cause Solutions
Refrigerator and
Freezer section are
not cooling.
The refrigerator control is set
to OFF (some models).
Turn the control ON. Refer to the Setting the Controls
section for proper temperature settings.
Refrigerator is set to Demo
Mode.
Demo Mode allows the lights and control display to work
normally while disabling cooling, to save energy while
WKHUHIULJHUDWRULVRQWKHVKRZURRPÀRRU6HHWKH)$4V
section of this manual for instructions on how to disable
Demo Mode.
Refrigerator is in the defrost
cycle.
During the defrost cycle, the temperature of each
compartment may rise slightly. Wait 30 minutes and
FRQ¿UPWKHSURSHUWHPSHUDWXUHKDVEHHQUHVWRUHGRQFH
the defrost cycle has completed.
Refrigerator was recently
installed.
It may take up to 24 hours for each compartment to
reach the desired temperature.
Refrigerator was recently
relocated.
If the refrigerator was stored for a long period of time or
moved on its side, it is necessary for the refrigerator to
stand upright for 24 hours before connecting it to power.
Cooling system
runs too much.
Refrigerator is replacing an
older model.
Modern refrigerators require more operating time but use
OHVVHQHUJ\GXHWRPRUHHI¿FLHQWWHFKQRORJ\
Refrigerator was recently
plugged in or power restored.
The refrigerator will take up to 24 hours to cool
completely.
The door is opened often or a
large amount of food / hot food
was added.
Adding food and opening the door warms the refrigerator,
requiring the compressor to run longer in order to cool
the refrigerator back down. In order to conserve energy,
try to get everything you need out of the refrigerator at
RQFHNHHSIRRGRUJDQL]HGVRLWLVHDV\WR¿QGDQGFORVH
the door as soon as the food is removed. (Refer to the
Food Storage Guide.)
Doors are not closed
completely.
Firmly push the doors shut. If they will not shut all the
way, the "Doors will not close correctly or pop open"
section.
Refrigerator is installed in a
hot location.
The compressor will run longer under warm conditions.
At normal room temperatures (70 °F) expect your
FRPSUHVVRUWRUXQDERXWWRRIWKHWLPH8QGHU
warmer conditions, expect it to run even more often. The
refrigerator should not be operated above 110 °F.
Condenser / back cover is
clogged.
Use a vacuum cleaner with an attachment to clean the
condenser cover and vents. Do not remove the panel
covering the condenser coil area.
55TROUBLESHOOTING
ENGLISH
Cooling
Problem Possible Cause Solutions
Interior moisture
buildup.
Doors are opened often or for
long periods of time.
When the doors are opened often or for long periods
of time, warm, humid air enters the compartment. This
raises the temperature and moisture level within the
compartment. To lessen the effect, reduce the frequency
and duration of door openings.
Doors are not closed correctly.
See the "Doors will not close correctly or pop open"
section.
Weather is humid.
Humid weather allows additional moisture to enter the
compartments when the doors are opened leading to
condensation or frost. Maintaining a reasonable level of
humidity in the home will help to control the amount of
moisture that can enter the compartments.
Defrost cycle recently
completed.
During the defrost cycle, the temperature of each
compartment may rise slightly and condensation may
IRUPRQWKHEDFNZDOO:DLWPLQXWHVDQGFRQ¿UPWKDW
the proper temperature has been restored once the
defrost cycle has completed.
Food is not packaged
correctly.
Food stored uncovered or unwrapped, and damp
containers can lead to moisture accumulation within each
compartment. Wipe all containers dry and store food in
sealed packaging to prevent condensation and frost.
Food is freezing
in the refrigerator
compartment.
Food with high water content
was placed near an air vent.
Rearrange items with high water content away from air
vents.
Refrigerator temperature
control is set incorrectly.
If the temperature is too cold, adjust the control one
increment at a time and wait for the temperature to
stabilize. Refer to the Control Panel section for more
information.
Refrigerator is installed in a
cold location.
When the refrigerator is operated in temperature
below 41°F (5°C), food can freeze in the refrigerator
compartment. The refrigerator should not be operated in
temperature below 55°F (13°C).
Refrigerator or
Freezer section is
too warm.
Refrigerator was recently
installed.
It may take up to 24 hours for each compartment to
reach the desired temperature.
The air vents are blocked. Cold
air circulates from the freezer
to the fresh food section and
back again through air vents
in the wall dividing the two
sections.
/RFDWHDLUYHQWVE\XVLQJ\RXUKDQGWRVHQVHDLUÀRZDQG
PRYHDOOSDFNDJHVWKDWEORFNYHQWVDQGUHVWULFWDLUÀRZ
5HDUUDQJHLWHPVWRDOORZDLUWRÀRZWKURXJKRXWWKH
compartment.
56 TROUBLESHOOTING
Cooling/Ice & Water
Problem Possible Cause Solutions
Refrigerator or
Freezer section is
too warm.
Doors are opened often or for
long periods of time.
When the doors are opened often or for long periods
of time, warm, humid air enters the compartment. This
raises the temperature and moisture level within the
compartment. To lessen the effect, reduce the frequency
and duration of door openings.
Unit is installed in a hot
location.
The refrigerator should not be operated in temperatures
above 110 °F.
A large amount of food or
hot food was added to either
compartment.
Adding food warms the compartment requiring the
cooling system to run. Allowing hot food to cool to room
temperature before putting it in the refrigerator will
reduce this effect.
Doors not closed correctly.
See the Doors will not close correctly or pop open
section in Parts & Features Troubleshooting.
Temperature control is not set
correctly.
If the temperature is too warm, adjust the control one
increment at a time and wait for the temperature to
stabilize.
Defrost cycle has recently
completed.
During the defrost cycle, the temperature of each
compartment may rise slightly and condensation may
IRUPRQWKHEDFNZDOO:DLWPLQXWHVDQGFRQ¿UPWKH
proper temperature has been restored once the defrost
cycle has completed.
Refrigerator or
Freezer section is
too cold.
Incorrect temperature control
settings.
If the temperature is too cold, adjust the control one
increment at a time and wait for the temperature to
stabilize. Refer to the Control Panel for more information.
Frost or ice crystals
form on frozen food
(inside of sealed
package).
Condensation from food with a
high water content has frozen
inside of the food package.
This is normal for food items with a high water content.
Food has been left in the
freezer for a long period of
time.
Do not store food items with high water content in the
freezer for a long period of time.
Frost or ice crystals
form on frozen
food (outside of
package).
Door is opened frequently or
for long periods of time.
When the doors are opened often or for long periods
of time, warm, humid air enters the compartment. This
raises the temperature and moisture level within the
compartment. Increased moisture will lead to frost and
condensation. To lessen the effect, reduce the frequency
and duration of door openings.
Door is not closing properly.
Refer to the Doors will not close correctly or pop open
section in the Troubleshooting section.
57TROUBLESHOOTING
ENGLISH
Ice & Water
Problem Possible Cause Solutions
Icemaker is
not making
enough ice.
Demand exceeds ice storage
capacity.
The icemaker will produce approximately 70-184 cubes
in a 24 hour period.
House water supply is not
connected, valve is not turned on
fully, or valve is clogged.
Connect the refrigerator to a cold water supply with
adequate pressure and turn the water shutoff valve fully
open. If the problem persists, it may be necessary to
contact a plumber.
:DWHU¿OWHUKDVEHHQH[KDXVWHG
5HSODFLQJWKHZDWHU¿OWHULVUHFRPPHQGHG
Approximately every six months.
:KHQWKHZDWHU¿OWHULQGLFDWRUWXUQVRQ
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
Low house water supply pressure.
The water pressure must be between 20 and 120 psi on
PRGHOVZLWKRXWDZDWHU¿OWHUDQGEHWZHHQDQGSVL
RQPRGHOVZLWKDZDWHU¿OWHU,IWKHSUREOHPSHUVLVWVLW
may be necessary to contact a plumber.
5HYHUVH2VPRVLV¿OWUDWLRQV\VWHP
is used.
5HYHUVHRVPRVLV¿OWUDWLRQV\VWHPVFDQUHGXFHWKH
water pressure below the minimum amount and result
in icemaker issues. (Refer to the Connecting the Water
Line section.)
Tubing connecting refrigerator to
house supply valve is kinked.
The tubing can kink when the refrigerator is moved
during installation or cleaning resulting in reduced water
ÀRZ6WUDLJKWHQRUUHSDLUWKHZDWHUVXSSO\OLQHDQG
arrange it to prevent future kinks.
Doors are opened often or for long
periods of time.
If the doors of the unit are opened often, ambient air
will warm the refrigerator which will prevent the unit
from maintaining the set temperature. Lowering the
refrigerator temperature can help, as well as not opening
the doors as frequently.
Doors are not closed completely.
If the doors are not properly closed, ice production will be
affected. See the "Doors will not close correctly or pop
open" section in Parts & Features Troubleshooting for
more information.
The temperature setting for the
freezer is too warm.
The recommended temperature for the freezer
compartment for normal ice production is 0°F. If the
freezer temperature is warmer, ice production will be
affected.
Icemaker is
not making
ice
Refrigerator was recently installed
or icemaker recently connected.
It may take up to 24 hours for each compartment to
reach the desired temperature and for the icemaker to
begin making ice.
Icemaker not turned on.
/RFDWHWKHLFHPDNHU212))DQGFRQ¿UPWKDWLWLV
turned on.
58 TROUBLESHOOTING
Ice & Water
Problem Possible Cause Solutions
Icemaker is not
making ice
The ice detecting sensor is
obstructed.
Foreign substances or frost on the ice-detecting sensor
can interrupt ice production. Make sure that the sensor
area is clean at all times for proper operation.
The refrigerator is not
connected to a water supply or
the supply shutoff valve is not
turned on.
Connect the refrigerator to the water supply and turn the
water shutoff valve fully open.
Icemaker shutoff (arm or
sensor) obstructed.
If your icemaker is equipped with an ice shutoff arm,
make sure that the arm moves freely. If your icemaker
is equipped with the electronic ice shutoff sensor, make
sure that there is a clear path between the two sensors.
Reverse osmosis water
¿OWUDWLRQV\VWHPLVFRQQHFWHG
to your cold water supply.
5HYHUVHRVPRVLV¿OWUDWLRQV\VWHPVFDQUHGXFHWKH
water pressure below the minimum amount and result
in icemaker issues. (Refer to the Connecting the Water
Line section.)
Ice has bad taste or
odor.
Water supply contains
minerals such as sulfur.
$ZDWHU¿OWHUPD\QHHGWREHLQVWDOOHGWRHOLPLQDWHWDVWH
DQGRGRUSUREOHPV127(,QVRPHFDVHVD¿OWHUPD\
not help. It may not be possible to remove all minerals/
odor/taste in all water supplies.
Icemaker was recently
installed.
Ice that has been stored for too long will shrink, become
cloudy, and may develop a stale taste. Throw away old
ice and make a new supply.
The food has not been
stored properly in either
compartment.
Rewrap the food. Odors may migrate to the ice if food is
not wrapped properly.
The interior of the refrigerator
needs to be cleaned.
See the Maintenance section for more information.
The ice storage bin needs to
be cleaned.
Empty and wash the bin (discard old cubes). Make sure
that the bin is completely dry before reinstalling it.
Icemaker is making
too much ice.
Icemaker shutoff (arm/ sensor)
is obstructed.
Empty the ice bin. If your icemaker is equipped with an
ice shutoff arm, make sure that the arm moves freely. If
your icemaker is equipped with the electronic ice shutoff
sensor, make sure that there is a clear path between the
two sensors. Reinstall the ice bin and wait 24 hours to
FRQ¿UPSURSHURSHUDWLRQ
Ice is not
dispensing.
Unable to hear the sound of
ice coming out?
In the control panel, select the modes for cubed ice and
crushed ice alternately to dispense the ice.
Doors are not closed
completely.
Ice will not dispense if any of the refrigerator doors are
left open.
59TROUBLESHOOTING
ENGLISH
Ice & Water
Problem Possible Cause Solutions
Ice is not
dispensing.
Infrequent use of the
dispenser.
Infrequent use of the ice dispenser will cause the cubes
to stick together over time, which will prevent them from
properly dispensing. Check the ice bin for ice cubes
clumping/sticking together. If they are, break up the ice
cubes to allow for proper operation.
The delivery chute is clogged
with frost or ice fragments.
Eliminate the frost or ice fragments by removing the
ice bin and clearing the chute with a plastic utensil.
Dispensing cubed ice can also help prevent frost or ice
fragment buildup.
The dispenser display is
locked.
Press and hold the Lock button for three seconds to
unlock the control panel and dispenser.
Ice bin is empty.
It may take up to 24 hours for each compartment to
reach the desired temperature and for the icemaker
to begin making ice. Make sure that the shutoff (arm/
sensor) is not obstructed. Once the ice supply in the
bin has been completely exhausted, it may take up
to 90 minutes before additional ice is available, and
DSSUR[LPDWHO\KRXUVWRFRPSOHWHO\UH¿OOWKHELQ
Water is dispensing
slowly.
:DWHU¿OWHUKDVEHHQ
exhausted.
5HSODFLQJWKHZDWHU¿OWHULVUHFRPPHQGHG
Approximately every six months.
:KHQWKHZDWHU¿OWHULQGLFDWRUWXUQVRQ
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
5HYHUVH2VPRVLV¿OWUDWLRQ
system is used.
5HYHUVHRVPRVLV¿OWUDWLRQV\VWHPVFDQUHGXFHWKH
water pressure below the minimum amount and result
in icemaker issues. If the problem persists, it may be
necessary to contact a plumber.
Low house water supply
pressure.
The water pressure must be between 20 and 120 psi on
PRGHOVZLWKRXWDZDWHU¿OWHUDQGEHWZHHQDQGSVL
RQPRGHOVZLWKDZDWHU¿OWHU,IWKHSUREOHPSHUVLVWVLW
may be necessary to contact a plumber.
Water is not
dispensing.
New installation or water line
recently connected.
'LVSHQVHJDOORQVRIZDWHUÀXVKIRUDSSUR[LPDWHO\
minutes) to remove trapped air and contaminants from
the system. Do not dispense the entire 2.5 gallon amount
continuously. Depress and release the dispenser pad for
cycles of 30 seconds ON and 60 seconds OFF.
The dispenser panel is locked.
Press and hold the Lock button for three seconds to
unlock the control panel and dispenser.
The dispenser is not set for
water dispensing.
The dispenser can be set for ice or water. Make certain
that the control panel is set for the proper operation.
Press the Water button on the control panel to dispense
water.
60 TROUBLESHOOTING
Ice & Water
Problem Possible Cause Solutions
Water is not
dispensing.
Refrigerator or freezer doors
are not closed properly.
Water will not dispense if any of the refrigerator doors
are left open.
:DWHU¿OWHUKDVEHHQUHFHQWO\
removed or replaced.
$IWHUWKHZDWHU¿OWHULVUHSODFHGGLVSHQVHJDOORQVRI
ZDWHUÀXVKIRUDSSUR[LPDWHO\¿YHPLQXWHVWRUHPRYH
trapped air and contaminants from the system. Do not
dispense the entire 2.5 gallon amount continuously.
Depress and release the dispenser pad for cycles of 30
seconds ON and 60 seconds OFF.
Tubing connecting refrigerator
to house supply valve is
kinked.
The tubing can kink when the refrigerator is moved
during installation or cleaning. Resulting in reduced
ZDWHUÀRZ6WUDLJKWHQRUUHSDLUWKHZDWHUVXSSO\OLQHDQG
arrange it to prevent future kinks.
The house water supply is not
connected, the valve is not
turned on fully, or the valve is
clogged.
Connect the refrigerator to the water supply and turn the
water shutoff valve fully open. If the problem persists, it
may be necessary to contact a plumber.
Dispensing warm
water.
Refrigerator was recently
installed.
Allow 24 hours after installation for the water storage
tank to cool completely.
The water dispenser has been
used recently and the storage
tank was exhausted.
'HSHQGLQJRQ\RXUVSHFL¿FPRGHOWKHZDWHUVWRUDJH
capacity will range from approximately 20 to 30 oz.
Dispenser has not been used
for several hours.
If the dispenser has not been used for several hours, the
¿UVWJODVVGLVSHQVHGPD\EHZDUP'LVFDUGWKH¿UVW
oz.
Refrigerator is connected to
the hot water supply.
Make sure that the refrigerator is connected to a cold
water pipe.
WARNING: Connecting the refrigerator to a hot water
line may damage the icemaker.
Water has bad taste
or odor.
Water supply contains
minerals such as sulfur.
$ZDWHU¿OWHUPD\QHHGWREHLQVWDOOHGWRHOLPLQDWHWDVWH
and odor problems.
:DWHU¿OWHUKDVEHHQ
exhausted.
5HSODFLQJWKHZDWHU¿OWHULVUHFRPPHQGHG
Approximately every six months.
:KHQWKHZDWHU¿OWHULQGLFDWRUWXUQVRQ
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
Refrigerator was recently
installed.
'LVSHQVHJDOORQVRIZDWHUÀXVKIRUDSSUR[LPDWHO\
minutes) to remove trapped air and contaminants from
the system. Do not dispense the entire 2.5 gallon amount
continuously. Depress and release the dispenser pad for
cycles of 30 seconds ON and 60 seconds OFF.
61TROUBLESHOOTING
ENGLISH
Parts & Features
Problem Possible Cause Solutions
Doors will not close
correctly or pop
open.
Food packages are blocking
the door open.
Rearrange food containers to clear the door and door
shelves.
Ice bin, crisper cover, pans,
shelves, door bins, or baskets
are out of position.
Push bins all the way in and put crisper cover, pans,
shelves and baskets into their correct positions. See the
Operation section for more information.
The doors were removed
during product installation and
not properly replaced.
Remove and replace the doors according to the
Removing and Replacing Refrigerator Handles and
Doors section.
Refrigerator is not leveled
properly.
See Door Alignment in the Refrigeration Installation
section to level refrigerator.
'RRUVDUHGLI¿FXOW
to open.
The gaskets are dirty or sticky.
Clean the gaskets and the surfaces that they touch. Rub
a thin coat of appliance polish or kitchen wax on the
gaskets after cleaning.
Door was recently closed.
When you open the door, warmer air enters the
refrigerator. As the warm air cools, it can create a
vacuum. If the door is hard to open, wait one minute to
allow the air pressure to equalize, then see if it opens
more easily.
Refrigerator
wobbles or seems
unstable
/HYHOLQJOHJVDUHQRWDGMXVWHG
properly.
Refer to the Leveling and Door Alignment section.
Floor is not level.
It may be necessary to add shims under the leveling legs
or rollers to complete installation.
Lights do not work. LED interior lighting failure.
The refrigerator compartment lamp is LED interior
OLJKWLQJDQGVHUYLFHVKRXOGEHSHUIRUPHGE\DTXDOL¿HG
technician.
Refrigerator has an
unusual odor.
The Air Filter may need to
be set to the MAX setting or
replaced.
Set the Air Filter to the MAX setting. If the odor does
QRWJRDZD\ZLWKLQKRXUVWKH¿OWHUPD\QHHGWREH
replaced. See the Replacing the Air Filter section for
replacement instructions.
The interior of
the refrigerator is
covered with dust
or soot.
The refrigerator is located
QHDUD¿UHVRXUFHVXFKDVD
¿UHSODFHFKLPQH\RUFDQGOH
0DNHVXUHWKDWWKHUHIULJHUDWRULVQRWORFDWHGQHDUD¿UH
VRXUFHVXFKDVD¿UHSODFHFKLPQH\RUFDQGOH
62 TROUBLESHOOTING
Noises
Problem Possible Cause Solutions
Clicking
The defrost control will click when the
automatic defrost cycle begins and ends.
The thermostat control (or refrigerator
control on some models) will also click
when cycling on and off.
Normal Operation
Rattling
5DWWOLQJQRLVHVPD\FRPHIURPWKHÀRZ
of refrigerant, the water line on the back
of the unit, or items stored on top of or
around the refrigerator.
Normal Operation
Refrigerator is not resting solidly on the
ÀRRU
Floor is weak or uneven or leveling legs need
to be adjusted. See the Leveling and Door
Alignment section.
Refrigerator with linear compressor was
MDUUHGZKLOHUXQQLQJ
Normal Operation
Whooshing
Evaporator fan motor is circulating air
through the refrigerator and freezer
compartments.
Normal Operation
Air is being forced over the condenser by
the condenser fan.
Normal Operation
Gurgling
5HIULJHUDQWÀRZLQJWKURXJKWKHFRROLQJ
system.
Normal Operation
Popping
Contraction and expansion of the inside
walls due to changes in temperature.
Normal Operation
Sizzling
Water dripping on the defrost heater
during a defrost cycle.
Normal Operation
Vibrating
If the side or back of the refrigerator is
touching a cabinet or wall, some of the
normal vibrations may make an audible
sound.
To eliminate the noise, make sure that the
sides and back cannot vibrate against any
wall or cabinet.
Dripping
Water running into the drain pan during
the defrost cycle.
Normal Operation
Pulsating or high-
pitched sound
Your refrigerator is designed to run
PRUHHI¿FLHQWO\WRNHHS\RXUIRRGLWHPV
at the desired temperature. The high
HI¿FLHQF\FRPSUHVVRUPD\FDXVH\RXU
new refrigerator to run longer than
your old one, but it is still more energy
HI¿FLHQWWKDQSUHYLRXVPRGHOV:KLOHWKH
refrigerator is running, it is normal to hear
a pulsating or high-pitched sound.
Normal Operation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

LG Electronics LFXS28566D Mode d'emploi

LG Electronics
Marque
LG Electronics
Modèle
LFXS28566D
Catégorie
Réfrigérateurs-congélateurs côte à côte
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents