Bolens 11A-109Q565 Le manuel du propriétaire

Marque: Bolens

Modèle: 11A-109Q565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

PRINTED IN U.S.A. MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1

OPERATOR’S MANUAL

IMPORTANT:

READ SAFETY RULES AND INSTRUCTIONS

CAREFULLY BEFORE OPERATING EQUIPMENT.

Safety • Setup • Adjustments • Operation • Maintenance • Troubleshooting • Parts Lists • Warranty

20” Rotary Mower — Model Series 100

11/10 / 09

769-04701A

Finding and Recording Model Number

Table of Contents

This Operator’s Manual is an important part of your new equipment. It will help you assemble,

prepare and maintain the unit for best performance. Please read and understand what it says.

Slope Gauge........................................................ 3

Safe Operation Practices ................................... 4

Safety Symbols ................................................... 7

Set-Up & Adjustments ........................................ 8

Operation ........................................................... 10

Maintenance ...................................................... 12

Off-Season Storage .......................................... 13

Trouble Shooting .............................................. 14

Warranty ............................................................ 15

Illustrated Parts Lists ....................................... 16

Please do

NOT

return the unit to the retailer from which it was purchased,

without rst contacting Customer Support.

Customer Support

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,

you can seek help from the experts. Choose from the options below:

1. Visit www.mtdcanada.ca for many useful suggestions, click on Customer Support button.

2. Call a Customer Support Representative at 1-800-668-1238.

3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,

warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed

separately with this product.

Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

BEFORE YOU START ASSEMBLING

YOUR NEW EQUIPMENT,

please locate the model plate on the equipment and record

the information in the provided area to the right. You can

locate the model plate by standing at the operating position

and looking down at the rear of the machine. This information

will be necessary, should you seek technical support.

Mo d e l Nu M b e r

Se r i a l Nu M b e r

Slope

Gauge

WARNING

Do not mow on inclines

with a slope in excess

of 15 degrees (a rise

of approximately

2-1/2 feet every 10

feet). A riding mower

could overturn and

cause serious injury.

If operating a walk-

behind mower on such

a slope, it is extremely

difficult to maintain your

footing and you could

slip, resulting in serious

injury.

Operate RIDING

mowers up and down

slopes, never across

the face of slopes.

Operate

WALK-BEHIND

mowers across the

face of slopes, never

up and down slopes.

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (represents a 15° slope)

15°

Use this page as a guide to determine slopes where you may not operate safely. Do not operate

your lawn mower on such slopes.

Safe

Operation

Practices

General Operation

1. Read this operator’s manual carefully in its entirety

before attempting to assemble this machine. Read,

understand, and follow all instructions on the ma-

chine and in the manual(s) before operation. Keep

this manual in a safe place for future and regular

reference and for ordering replacement parts.

2. Be completely familiar with the controls and the

proper use of this machine before operating it.

3. This machine is a precision piece of power equip-

ment, not a plaything. Therefore, exercise extreme

caution at all times. Your unit has been designed to

perform one job: to mow grass. Do not use it for any

other purpose.

4. Never allow children under 14 years old to operate

this machine. Children 14 years old and over should

read and understand the instructions in this manual

and should be trained and supervised by a adult.

5. Only responsible individuals who are familiar with

these rules of safe operation should be allowed to

use this machine.

6. Thoroughly inspect the area where the equipment is

to be used. Remove all stones, sticks, wire, bones,

toys and other foreign objects which could be tripped

over or picked up and thrown by the blade. Thrown

objects can cause serious personal injury.

7. Plan your mowing pattern to avoid discharge of

material toward roads, sidewalks, bystanders and the

like. Also, avoid discharging material against a wall

or obstruction which may cause discharged material

to ricochet back toward the operator.

8. To help avoid blade contact or a thrown object injury,

stay in the operator zone behind the handles and

keep children, bystanders, helpers and pets at least

75 feet from the mower while it is in operation. Stop

machine if anyone enters the area.

9. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

10. Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Shirts and pants that

cover the arms and legs and steel-toed shoes are

recommended. Never operate this machine in bare

feet, sandals, slippery or light weight (e.g. canvas)

shoes.

11. Do not put hands or feet near rotating parts or under

the cutting deck. Contact with the blade can amputate

hands and feet.

12. A missing or damaged discharge cover can cause

blade contact or thrown object injuries.

13. Many injuries occur as a result of the mower being

pulled over the foot during a fall caused by slipping or

tripping. Do not hold on to the mower if you are falling;

release the handle immediately.

14. Never pull the mower back toward you while you are

walking. If you must back the mower away from a wall

or obstruction first look down and behind to avoid

tripping and then follow these steps:

a. Step back from the mower to fully extend your

arms.

b. Be sure you are well balanced with sure footing.

c. Pull the mower back slowly, no more than half way

toward you.

d. Repeat these steps as needed.

15. Do not operate the mower while under the influence of

alcohol or drugs.

16. Do not engage the self-propelled mechanism on units

so equipped while starting engine.

17. The blade control handle is a safety device. Never

attempt to bypass its operation. Doing so makes the

safety device inoperative and may result in personal

injury through contact with the rotating blade. The

blade control handle must operate easily in both

directions and automatically return to the disengaged

position when released.

18. Never operate the mower in wet grass. Always be

sure of your footing. A slip and fall can cause serious

personal injury. If you feel you are losing your footing,

release the blade control handle immediately and the

blade will stop rotating within three seconds.

19. Mow only in daylight or in good artificial light. Walk,

never run.

20. Stop the blade when crossing gravel drives, walks or

roads.

21. If the equipment should start to vibrate abnormally,

stop the engine and check immediately for the cause.

Vibration is generally a warning of trouble.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain

or emit chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

WARNING

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this

manual before at-

tempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

HEED ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with

any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This

machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

22. Shut the engine off and wait until the blade comes to

a complete stop before removing the grass catcher or

unclogging the chute. The cutting blade continues to

rotate for a few seconds after the engine is shut off.

Never place any part of the body in the blade area until

you are sure the blade has stopped rotating.

23. Never operate mower without proper trail shield,

discharge cover, grass catcher, blade control handle or

other safety protective devices in place and working.

Never operate mower with damaged safety devices.

Failure to do so, can result in personal injury.

24. Muffler and engine become hot and can cause a burn.

Do not touch.

25. Never attempt to make a wheel or cutting height

adjustment while the engine is running.

26. Only use parts and accessories made for this machine

by the manufacturer. Failure to do so can result in

personal injury.

27. When starting engine, pull cord slowly until resistance

is felt, then pull rapidly. Rapid retraction of starter cord

(kickback) will pull hand and arm toward engine faster

than you can let go. Broken bones, fractures, bruises

or sprains could result.

28. If situations occur which are not covered in this

manual, use care and good judgment. Call customer

assistance for the name of your nearest servicing

dealer.

Slope Operation

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. Operation on slopes

requires extra caution. If you feel uneasy on a slope, do

not mow it. For your safety, use the slope gauge included

as part of this manual to measure slopes before operating

this unit on a sloped or hilly area. If the slope is greater

than 15 degrees, do not mow it.

Do:

1. Mow across the face of slopes; never up and down.

Exercise extreme caution when changing direction on

slopes.

2. Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide

obstacles.

3. Always be sure of your footing. A slip and fall can

cause serious personal injury. If you feel you are

losing your balance, release the blade control handle

immediately, and the blade will stop rotating within 3

seconds.

Do Not:

1. Do not mow near drop-offs, ditches or embankments,

you could lose your footing or balance.

2. Do not mow slopes greater than 15 degrees as shown on the

slope gauge.

3. Do not mow on wet grass. Unstable footing could

cause slipping.

Children

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted

to the mower and the mowing activity. They do not

understand the dangers. Never assume that children

will remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. Be alert and turn mower off if a child enters the area.

3. Before and while moving backwards, look behind

and down for small children.

4. Use extreme care when approaching blind corners,

doorways, shrubs, trees, or other objects that may

obscure your vision of a child who may run into the

mower.

5. Keep children away from hot or running engines.

They can suffer burns from a hot muffler.

6. Never allow children under 14 years old to operate a

power mower. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and shou

ld be trained and

supervised by a parent.

Service

Safe Handling Of Gasoline:

1. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

2. Use only an approved gasoline container.

3. Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place contain-

ers on the ground away from your vehicle before

filling.

4. Remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer with

a portable container, rather than from a gasoline

dispenser nozzle.

5. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

6 Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

7. Never fuel machine indoors because flammable

vapors will accumulate in the area.

8. Never remove gas cap or add fuel while the engine

is hot or running. Allow engine to cool at least two

minutes before refueling.

Safe

Operation

Practices

WARNING

This machine is equipped

with an internal combus-

tion engine and should

not be used on or near

any unimproved forest-

covered, brushcovered or

grass-covered land unless

the engine’s exhaust

system is equipped with a

spark arrester meeting ap-

plicable local or provincial

laws (if any).

If a spark arrester is used,

it should be maintained in

effective working order by

the operator.

A spark arrester for the muf-

fler is available through your

nearest engine authorized

service dealer.

Notice regarding Emis-

sions

Engines which are certified

to comply with California

and federal EPA emission

regulations for SORE (Small

Off Road Equipment) are

certified to operate on regu-

lar unleaded gasoline, and

may include the following

emission control systems:

Engine Modification (EM)

and Three Way Catalyst

(TWC) if so equipped.

9. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to provide for fuel

expansion.

10. Replace gasoline cap and tighten securely.

11. If gasoline is spilled, wipe it off the engine and equip-

ment. Move unit to another area. Wait 5 minutes

before starting the engine.

12. Never store the machine or fuel container near an

open flame, spark or pilot light as on a water heater,

space heater, furnace, clothes dryer or other gas

appliances.

13. To reduce fire hazard, keep mower free of grass,

leaves, or other debris build-up. Clean up oil or fuel

spillage and remove any fuel soaked debris.

14. Allow a mower to cool at least 5 minutes before

storing.

General Service:

1. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

2. Before cleaning, repairing, or inspecting, make

certain the blade and all moving parts have stopped.

Disconnect the spark plug wire and ground against

the engine to prevent unintended starting.

3. Check the blade and engine mounting bolts at

frequent intervals for proper tightness. Also, visually

inspect blade for damage (e.g., bent, cracked, worn)

Replace blade with the original equipment manufac-

ture’s (O.E.M.) blade only, listed in this manual. “Use

of parts which do not meet the original equipment

specifications may lead to improper performance

and compromise safety!”

4. Mower blades are sharp and can cut. Wrap the blade

or wear gloves, and use extra caution when servicing

them.

5. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

6. Never tamper with safety devices. Check their proper

operation regularly.

7. After striking a foreign object, stop the engine,

disconnect the spark plug wire and ground against

the engine. Thoroughly inspect the mower for any

damage. Repair the damage before starting and

operating the mower.

8. Never attempt to make a wheel or cutting height

adjustment while the engine is running.

9. Grass catcher components, discharge cover, and trail

shield are subject to wear and damage which could

expose moving parts or allow objects to be thrown. For

safety protection, frequently check components and

replace immediately with original equipment manufac-

turer’s (O.E.M.) parts only, listed in this manual. “Use

of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

10. Do not change the engine governor setting or

overspeed the engine. The governor controls the

maximum safe operating speed of the engine.

11. Check fuel line, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

12. Do not crank engine with spark plug removed.

13. Maintain or replace safety labels, as necessary.

14. Observe proper disposal laws and regulations.

Improper disposal of fluids and materials can harm the

environment.

15. According to the Consumer Products Safety Commis-

sion (CPSC) and the U.S. Environmental Protection

Agency (EPA), this product has an

Average Useful Life

of seven (7) years, or 60 hours of operation. At the

end of the Average Useful Life, buy a new machine or

have the machine inspected annually by an authorized

service dealer to ensure that all mechanical and safety

systems are working properly and not worn exces-

sively. Failure to do so can result in accidents, injuries

or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in

any way. Tampering with the governor setting can lead

to a runaway engine and cause it to operate at unsafe

speeds. Never tamper with factory setting of engine

governor.

Safe

Operation

Practices

WARNING

This symbol points

out important safety

instructions which,

if not followed,

could endanger the

personal safety and/

or property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

HEED ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

WARNING: Your Responsibility—Restrict the use of this power machine to persons who

read, understand and follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before

attempting to assemble and operate

DANGER — ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate

unless discharge cover or grass catcher is in its proper place. If damaged,

DANGER — BYSTANDERS

Do not mow when children or others are around.

DANGER — HAND/ FOOT CUT

Keep hands and feet away from rotating parts.

DANGER — THROWN DEBRIS

Remove objects that can be thrown by the blade in any direction. Wear

safety glasses.

DANGER — SLOPES

Use extra caution on slopes. Do not mow slopes greater than 15°.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust

contains carbon monoxide, an odorless and deadly gas.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during opera-

tion. Allow engine and muffler to cool before touching.

Safety

Symbols

WARNING

This symbol points

out important safety

instructions which,

if not followed, could

endanger the per-

sonal safety and/or

property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may

result in personal

injury. When you see

this symbol, HEED

ITS WARNING!

NOTE: Reference to right, left, front and rear

of the lawn mower is in relation to the operating

position.

WARNING: Disconnect and

ground the spark plug wire as

instructed in the separate engine

manual.

1. Remove any packing material which may be

between upper and lower handles.

a. Pull up and back on the upper handle to

raise the handle into the operating position.

Position A.

b. Tighten knobs securing upper handle to

lower handle. Make sure that each car-

riage bolt is seated properly in the handle.

Position B.

Figure 4-3

Figure 4-2

Figure 4-1

Setup and

Adjustments

IMPORTANT

This unit is shipped

WITHOUT GASOLINE

or OIL. After assem-

bly, service engine

with gasoline and

oil as instructed in

the separate engine

manual packed with

your unit.

2. Locate hairpin clip in one hole on the weld pin

on each side of lower handle. Figure 4-2.

a. Remove hairpin clip from this hole. Using

a pair of pliers, insert hairpin clip into the

other hole on the weld pin. Repeat on

other side. Position A.

3. Rope guide Setup as follows, see Figure 4-3.

a. Hold the blade control against the upper

handle. Position A.

b. Slowly pull starter rope out of engine.

Position B.

c. Slip starter rope into the rope guide. Posi-

tion C.

d. Tighten rope guide wing nut (star knobs).

Position D.

This owner’s manual

covers various models

of lawnmowers. The

units illustrated may

vary slightly from your

unit. Follow only those

instructions which

pertain to your model

lawnmower.

Figure 4-4

NOTE: All wheels must

be in the same height

of cut.

When cutting in heavy

or moist grass, the rear

of the lawnmower may

be raised higher to

allow better discharge

of the grass.

Setup and

Adjustments

4. Insert post on cable ties into holes provided

on the lower handle. Pull cable tie tight and

trim excess. See Figure 4-4.

Figure 4-6

Figure 4-5

5. Each wheel has a height adjustment lever to

change the cutting height of the mower. To

change the height of cut, squeeze adjuster

lever toward the wheel, moving up or down to

selected height. See Figure 4-5.

6. Your mower has been shipped as a mulcher.

To discharge grass to the side, lift mulching

plug. Slide the two hooks on the side

discharge deflector under the hinge pin on

the mulching plug assembly, see Figure 4-6.

Lower the mulching plug.

Operating

Your Lawn

Mower

Blade Control Handle

The blade control handle is located on the

upper handle of the mower. See Figure 5-1.

The blade control handle must be depressed

in order to operate the unit. Release the blade

control handle to stop the engine and blade.

Recoil Starter

The recoil starter is attached to the right upper

handle. Stand behind the unit and pull the recoil

starter rope to start the unit.

Mulching Plug

The mulching plug is used to recirculate

grass clippings back to the lawn. Attach it as

instructed on page 9 of this manual.

Cutting Height Adjustment Levers

One adjustment lever is located on each wheel

and is used to adjust the cutting height. All four

levers have to be at the same relative position

to ensure uniform cut.

Know Your Lawn Mower

Before Starting

1. Service the engine with gasoline and oil as

instructed in the separate engine manual.

2. Attach spark plug wire to spark plug. If unit is

equipped with a rubber boot over the end of

the spark plug wire, make certain the metal

loop on the end of the spark plug wire (inside

the rubber boot) is fastened securely over the

metal tip on the spark plug.

WARNING: Be sure no one other

than the operator is standing near

the lawn mower while starting

engine or operating mower. Never

run engine indoors or in enclosed,

poorly ventilated areas. Engine

exhaust contains carbon monox-

ide, an odorless and deadly gas.

Keep hands, feet, hair and loose

clothing away from any moving

parts on engine and lawn mower.

WARNING

Figure 5-1

10, 50

Blade Control Handle

Recoil

Starter

Height

Adjustment

Lever (front

and rear)

Mulch Plug

Chute Deflector

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

This blade control

mechanism is a

safety device. Never

attempt to bypass its

operations.

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

Operating

Your Lawn

Mower

WARNING

The operation of any

lawn mower can result

in foreign objects

being thrown into

the eyes, which can

damage your eyes

severely. Always wear

safety glasses while

operating the mower,

or while performing

any adjustments or

repairs on it.

Be sure no one other

than the operator is

standing near the lawn

mower while starting

engine or operating

mower. Never run

engine indoors or

in enclosed, poorly

ventilated areas. En-

gine exhaust contains

carbon monoxide, an

odorless and deadly

gas. Keep hands, feet,

hair and loose clothing

away from any moving

parts on engine and

lawn mower.

Figure 5-2

To Start Engine

Refer to the separate engine manual packed

with your unit.

1. Place the fuel valve lever found on the left

side of the engine into the ON (OPEN)

position, Fig. 5-2.

2. Move the choke lever (if equipped) all the

way backward into the choke position.

3. Standing behind the mower, squeeze the

blade control against upper handle. The

choke will now begin to slowly return to the

off choke position after activating the blade

control. Therefore, quickly move onto step

four below.

4. Pull the starter grip lightly until resistance is

felt, then pull rapidly to overcome compres-

sion, prevent kickback and start engine.

Repeat if necessary. See Figure 5-1 Do not

allow the starter grip to snap back against the

engine. Return it gently to prevent damage to

the starter.

To Stop Engine :

1. Release the blade control handle to stop the

engine and blade.

WARNING: The blade continues

to rotate for a few seconds after

the engine is shut off.

2. Disconnect and ground the spark plug wire

as instructed in the separate engine manual

to prevent accidental starting while equip-

ment is unattended.

Using Your Lawn Mower

Be sure the lawn is clear of stones, sticks, wire,

or other objects which could damage the lawn

mower or the engine. Such objects could be

accidently thrown by the mower in any direction

and cause serious personal injury to the opera-

tor and others.

WARNING: If you strike a foreign

object, stop the engine. Remove

wire from the spark plug, thor-

oughly inspect the mower for any

damage, and repair the damage

before restarting and operating

the mower. Extensive vibration

of the mower during operation is

an indication of damage. The unit

should be promptly inspected

and repaired.

Operating Tips

1. For best results and effective mulching, do

not cut wet grass.

2. New grass, thick grass, or wet grass may

require a narrower cut.

3. For a healthier lawn, never cut off more than

one-third of the total length of the grass.

4. Your lawn should be cut in the fall as long as

there

is growth.

5. Adjust ground speed according to condition

of lawn.

6. If the grass has been allowed to grow in

excess of 4 inches, mulching is not recom-

mended. Mow using the side discharge to

reduce the grass height to 3-1/4 inches or

less before mulching.

OFF

WARNING

Always stop engine,

disconnect spark

plug, and ground

against engine before

cleaning, lubricating

or doing any kind of

maintenance on your

machine.

Figure 6-1

General Recommendations

1. Always observe safety rules when

performing any maintenance.

2. The warranty on this lawn mower does not

cover items that have been subjected to

operator abuse or negligence. To receive full

value from warranty, operator must maintain

the lawn mower as instructed here.

3. Changing of engine-governed speed will void

engine warranty.

4. All adjustments should be checked at least

once each season.

5. Periodically check all fasteners and make

sure these are tight.

Lubrication

1. Lubricate the pivot points on the blade

control handle at least once a season with

light oil. The blade control must operate

freely in both directions. See Figure 6-1

2. If your mower is equipped with ball bearing

wheels, lubricate at least once a season

with a light oil, all other types require no

lubrication. However, if the wheels are

removed for any reason, lubricate the

surface of the axle bolt and the inner surface

of the wheel with light automotive oil.

3. Lubricate the torsion spring and pivot point

periodically with light oil to prevent rust. See

Figure 6-1.

4. Follow the accompanying engine manual for

lubrication schedule and instruction.

Lubricate these

points before

reassembly

Engine

1. Refer to the separate engine manual for

engine maintenance instructions.

2. Maintain engine oil as instructed in the

separate engine manual packed with your unit.

Read and follow instructions carefully.

3. Under normal conditions service air cleaner

as instructed in the separate engine manual

packed with your unit. Clean every few hours

under extremely dusty conditions. Poor

engine performance and flooding usually indi-

cates that the air cleaner should be serviced.

4. The spark plug should be cleaned and the gap

reset once a season. Spark plug replacement

is recommended at the start of each mowing

season; check engine manual for correct plug

type and gap specifications.

NOTE: This spark ignition system meets all

requirements of the Canadian Interference-

Causing Equipment Regulations.

5. Clean the engine regularly with a cloth or

brush. Keep the cooling system (blower hous-

ing area) clean to permit proper air circulation

which is essential to engine performance and

life. Be certain to remove all grass, dirt and

combustible debris from muffler area.

Deck

The underside of the mower deck should be

cleaned after each use to prevent a buildup of

grass clippings, leaves, dirt or other matter. If this

debris is allowed to accumulate, it will invite rust

and corrosion, and may prevent proper mulching.

The deck may be cleaned by tilting the mower

and scraping clean with a suitable tool (make

certain the spark plug wire is disconnected).

NOTE: If unit is tipped for easier access to

blade or belt, tip mower as specified in separate

engine manual. If it does not specify turn mower

on its side making sure that the air filter and the

carburetor are up.

Maintenance

WARNING

When removing

the cutting blade

for sharpening or

replacement, protect

your hands with a

pair of heavy gloves

or use a heavy rag to

hold the blade.

An unbalanced blade

will cause excessive

vibration when rotat-

ing at high speeds. It

may cause damage

to mower, and could

break causing per-

Figure 6-2

Blade Care

WARNING: When removing the

cutting blade for sharpening or

replacement, protect your hands

with a pair of heavy gloves or use

a heavy rag to hold the blade.

Periodically inspect the blade adapter for

cracks, especially if you strike a foreign object.

Replace when necessary. Follow the steps

below for blade service:

1. Disconnect spark plug wire from spark plug.

2. Tip mower as specified in separate engine

manual. If it does not specify turn mower on

its side making sure that the air filter and the

carburetor are up.

3. Remove the bolt and the blade bell support

which hold the blade and the blade adapter

to the engine crankshaft. See Figure 6-2.

4. Remove blade and adapter from the crank-

shaft.

5. The blade may be resharpened by removing

it and either grinding or filing the cutting edge

keeping as close to the original bevel as

possible. Do not attempt to sharpen the blade

while it is still on the mower.

6. It is extremely important that each cutting

edge receives an equal amount of grinding to

prevent an unbalanced blade.

NOTE: Improper blade balance will result in

excessive vibration causing eventual damage to

the engine and mower. Be sure to carefully bal-

ance blade after sharpening. Possible damage

resulting from blade unbalance condition is not

the responsibility of the manufacturer.

NOTE: Always remove blade from the adapter

for testing balance.

7. The blade can be tested for balance by

balancing it on a round shaft screwdriver.

Remove metal from the heavy side until it

balances evenly.

8. Before reassembling the blade and the blade

adapter to the unit, lubricate the engine

crankshaft and the inner surface of the blade

adapter with light oil.

Cutting grass in sandy

soil condition causes

abrasive wear to the

blade.

9. Install the blade adapter on the crankshaft

with the “star” away from the engine. See

Figure 6-2. Place the blade with the side

marked “bottom” (or with part number) facing

away from the adapter. Align the blade bell

support over the blade with the tabs in the

holes of the blade and insert the hex bolt.

10. Tighten the hex bolt to the torque listed

below:

Blade Mounting Torque

Center Bolt 450 in. lb. min., 600 in.lb. max.

To insure safe operation of your unit, ALL nuts

and bolts must be checked periodically for

correct tightness.

Off-Season Storage

The following steps should be taken to prepare

your lawn mower for storage.

1. Clean and lubricate mower thoroughly as

described in the lubrication instructions.

2. We do not recommend the use of a pressure

washer or garden hose to clean your unit.

3. Refer to engine manual for correct engine

storage instructions.

4. Coat mower’s cutting blade with chassis

grease to prevent rusting.

5. Store mower in a dry, clean area. Do not

store next to corrosive materials, such as

fertilizer.

NOTE: When storing any type of power equip-

ment in a poorly ventilated or metal storage

shed, care should be taken to rust-proof the

equipment. Using a light oil or silicone, coat the

equipment, especially cables and all moving

parts of your lawn mower before storage.

Maintenance

For repairs beyond

the minor adjust-

ments listed here,

contact an autho-

rized service dealer.

Trouble

Shooting

CauseProblem

Remedy

Engine fails to start

1. Blade control handle disengaged.

2. Spark plug wire disconnected.

3. Fuel tank empty or stale fuel.

4. Engine not primed.

5. Faulty spark plug.

6. Blocked fuel line.

7. Engine flooding.

1. Engage blade control handle.

2. Connect wire to spark plug.

3. Fill tank with clean, fresh gasoline.

4. Refer to engine manual.

5. Clean, adjust gap, or replace.

6. Clean fuel line.

7. Wait a few minutes to restart, but do not

prime.

Engine runs erratic 1. Connect and tighten spark

plug wire.

2. Clean fuel line; fill tank with clean, fresh

gasoline.

3. Clear vent.

4. Drain fuel tank and carburetor. Refill with

fresh fuel.

5. Refer to engine manual.

6. Refer to engine manual.

1. Spark plug wire loose.

2. Blocked fuel line or stale fuel.

3. Gas cap vent plugged.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Carburetor out of adjustment.

Engine overheats

1. Fill crankcase with proper oil.

2. Refer to the engine manual packed with

your unit.

3. Remove blower housing and clean.

4. Refer to engine manual.

1. Engine oil level low.

2. Dirty air filter.

3. Air flow restricted.

4. Carburetor not adjusted properly.

Occasional skip

(hesitates) at high speed

1. Adjust gap to .030”. Refer to engine

manual.

2. Refer to engine manual.

1. Spark plug gap too close.

2. Carburetor idle mixture adjustment

improperly set.

Idles poorly

1. Reset gap to .030” or replace spark plug.

Refer to engine manual.

2. Refer to engine manual.

3. Refer to engine manual.

1. Spark plug fouled, faulty or gap too

wide.

2. Carburetor improperly adjusted.

3. Dirty air cleaner.

1. Cutting Blade loose or unbalanced.

2. Bent cutting blade.

1. Tighten blade and adapter. Balance blade

2. Replace blade.

Excessive vibration

1. Wheels not positioned correctly.

2. Dull blade.

Uneven cut

1. Place all four wheels in same height

position.

2. Sharpen or replace blade.

1. Wet grass.

2. Excessive high grass.

3. Dull blade.

1. Do not mow when grass is wet;

wait until later to cut.

2. Mow once at a high cutting height, then

mow again at desired height or make a

narrower cutting path.

3. Sharpen or replace blade.

Mower will not mulch

grass

Warranty

Failure to comply

with suggested

maintenance

and lubrication

specifications will

void warranty.

4 YEAR LIMITED WARRANTY

For FOUR YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair

or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.

This warranty does not cover:

1. Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper mainte-

nance or alteration; or

2. The unit if it has not been operated and/or maintained in accordance with the owner’s instructions furnished with the

unit; or

3. The engine or motor or component parts thereof which carry separate warranties from their manufacturers. Please

refer to the applicable manufacturer’s warranty on these items; and read engine warranty statement below, or

4. Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or component parts

thereof are covered by a one year warranty; or

5. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake,

clutch or deck; or

6. Normal deterioration of the exterior finish due to use or exposure.

Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the date of retail purchase, if any

battery included with this unit proves defective in material or workmanship and our testing determines the battery will

not hold a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days but within one hundred

twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the

original purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.

Full Ninety Days Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adaptors, blades,

grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the original

purchaser to be free from defects in material and workmanship for a period of ninety (90) days from the date of retail

purchase.

How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service

dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238. The

return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD

PRODUCTS LIMITED.

Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are

the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this warranty

must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.

Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited

in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the

sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its products.

MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.

4 YEAR LIMITED WARRANTY ENGINES

This limited warranty doubles the time periods of the engine manufacturer’s limited warranty which is enclosed in the

owner’s information package.

12.08.06

For parts and/or

accessories refer to

customer support on

page 2.

Adressez-vous au

«Service après-vente»

à la page 2 pour ce qui

concerne les pièces

et/ou accessoires.

REF PA RT

NO. NO.

N° DE N° DE

RÉF PIÈCE DE SCRIP TION DE SCRIP TION

1 747-1161A Blade Con trol Han dle Poignée de la commande

2 731-2626 De luxe Cover - Black Couvercle - noir

731-04204 De luxe Cover - Red Couvercle - rouge

731-04859 De luxe Cover - Grey Couvercle - gris

3 687-02338 Pivot Arm LH Bras de pivotement - droit

4 687-02075B Hgt. Ad just Ass’y LH Réglage de hau teur - gauche (Comprend les

(Incl. Ref. No. 3, 20, 21, 26 & 39) no. de réf. 3, 20, 21, 26 et 39)

5 687-02074B Hgt. Ad just Ass’y RH Réglage de hau teur - droit (Comprend les

(Incl. Ref. No. 6, 20, 21, 26 & 39) no. de réf. 6, 20, 21, 26 et 39)

6 687-02337 Pivot Arm RH Bras de pivotement - droit

7 710-1205 Rope Guide Bolt Boulon de guidage de cor don

8 710-1174 Car riage Bolt 5/16-18 x 2.0 Boulon ordi naire 5/16-18 x 2,0

9 749-0928B Lower Han dle Guidon inférieur

10 720-0279 Knob - ERS Guide 1/4-20 Bou ton - 1/4-20

11 720-04072A Knob - Star 5/16-18 Bou ton - étoile 5/16-18

12 714-0104 Int. Cot ter Pin .072 x 1.13" Lg. Goupille fendue 0,072 x 1,13 po. de lg.

13 746-0957 Con trol Ca ble 37.25 " Lg. (Honda) Câble de la commande 37,25 po (Honda)

14 749-1092A Up per Han dle Guidon supérieur

15 726-0240 Ca ble Tie Attache câble

16 731-06952 Rear Flap Abattant de pro tec tion arrière

17 732-04631 Hinge Clip Attache

18 682-0139 Deck As sem bly Pla teau de coupe

19 687-02107A Rear Hgt. Ad just Ass’y LH Réglage de hau teur-gauche arrière (Comprend les

(Incl. Ref. No. 6, 20, 21, 26 & 28) no. de réf. 6, 20, 21, 26 et 28)

20 720-0426 Knob Bou ton

21 732-0404 Spring Le ver Lev ier de ressort

22 734-2004A Wheel Ass'y 8" x 2.125" Idle BB En sem ble de roue 8 x 2,125 po

734-04033 Wheel Ass'y 8" x 2.0" S-Wave BB En sem ble de roue 8 x 2,0 po

23 736-0504 Wave Washer .51" ID (w/bb wheels) Rondelle ondulée 0,51 DI (avec roulement à billes)

24 687-02106A Rear Hgt. Ad just Ass’y RH Réglage de hau teur - droit arrière (Comprend les

(Incl. Ref. No. 3, 20, 21, 26 & 27) no. de réf. 3, 20, 21, 26 et 27)

25 731-07049 Hub Cap - Yel low (op tional) Moyeu de cha peau - jaune (en op tion)

731-07001 Hub Cap - Grey (op tional) Moyeu de cha peau - gris (en op tion)

26 738-04266 Shoul der Screw .50 Dia. x .385 Vis à épaulement 0,50 Dia. x 0,385

27 687-02180 Ad just/Brkt. Ass’y RH Sup port - droit

28 687-02179 Ad just/Brkt. Ass’y LH Sup port - gauche

30 732-0731 Tor sion Spring Ressort de tor sion

32 782-7006 Hinged Adapter Adaptateur

33 736-0270 Cupped Washer .265 ID x .75 OD Rondelle creuse 0,265 DI x 0,75 DE

34 710-0599 Hex Wash S-Tapp Scr 1/4-20 x .50 Vis taraudée

35 710-0654A Hex Wash HD Tap Scr 3/8-16 x .88 Vis autotaraudée 3/8-16 x 0,88

36 731-1409B Chute De flec tor Déflecteur

37 731-1501A Mulch ing Plug Boucon de déchiquetage

38 712-04065 Flanged Lock Nut 3/8-16 Gr. F Écrou de blocage 3/8-16 Qual. F

39 787-01290A Height Ad juster Plate Plaque de réglage de roue

40 731-1933 Front End Cover -Yel low (op tional) Couvercle-jaune (en op tion)

731-1949 Front End Cover-Black (op tional) Couvercle-noir (en op tion)

41 748-04096 Blade Adapter Adaptateur de la lame

42 742-0740 20" Mulch ing Blade Lame 20 po

43 736-0524B Blade Bell Sup port Sup port de lame

44 710-1044 Hex Bolt 3/8-24 x 1.5" Lg. (Grade 8) Vis à tête hex. 3/8-24 x 1,50 po de lg (Qual. 8)

45 747-0710 Hinge Pin Axe fixe

47 682-7002 Hinged Mulch ing Plug Ass'y En sem ble de bouchon de déchiquetage à

charnière

106/700

11.12.09

Parts List

Pièces

détachées

Garantie

Le non-respect des

conseils d’entretien

et de lubrification

annule la garantie.

GARANTIE LIMITÉE DE QUATRE ANS

MTD PRODUCTS LIMITED s’engage à réparer ou à remplacer gratuitement, à son choix, à l’acheteur initial, toute

pièce ou partie de pièce qui s’avère défectueuse en raison d’un vice de matière ou de fabrication, dans un délai de

QUATRE ANS à partir de la date d’achat au détail au Canada.

Cette garantie ne couvre pas:

1. Les pièces rendues inutilisables par un emploi incorrect, une utilisation commerciale, un emploi abusif, une

négligence, un entretien incorrect ou une modification;

2. La machine si elle n’a pas été utilisée et/ou entretenue conformément aux instructions qui l’accompagnaient;

3. Le moteur, le moteur électrique ou l’un de ses composants car ils sont garantis par leurs fabricants respectifs.

Veuillez consulter la garantie qui s’applique à la pièce en particulier; et lisez le paragraphe ci-dessous au sujet de

la garantie des moteurs;

4. Les batteries et les pièces présentant une usure normale énumérées plus bas. Les pompes, soupapes et cylindres

des fendeuses à bois sont garantis pendant un an;

5. Les articles d’entretien courant tels que les lubrifiants, filtres, aiguisage de lames et révisions, ou les réglages des

freins, de l’embrayage ou du plateau de coupe;

6. La détérioration normale de la finition extérieur du fait de l’utilisation de la machine et de son exposition aux

intempéries.

Garantie complète de quatre-vingt-dix jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED

s’engage à remplacer gratuitement à l’acheteur initial, pour une période de quatre-vingt-dix (90) jours à compter de

la date d’achat au détail, toute batterie fournie avec cette machine qui s’avère défectueuse en raison d’un vice de

matière ou de fabrication et après que nos tests aient confirmé qu’elle ne peut maintenir une charge.

Garantie limitée supplémentaire de trente jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED

s’engage, à l’expiration de la période de quatre-vingt-dix (90) jours et avant la fin d’une période de cent vingt (120)

jours à compter de la date d’achat, à remplacer la batterie défectueuse à l’acheteur initial, pour la moitié (1/2) du prix

de détail en vigueur de la batterie à la date du retour de celle-ci.

Garantie complète de quatre-vingt-dix (90) jours des pièces à usure normale: Les courroies, adaptateurs de

lame, lames, sacs à herbe, sièges, pneus, roues du plateau de coupe des tondeuses à siège, et pièces d’embrayage

(roues de frottement) sont considérés comme des pièces à usure normale. Elles sont garanties exemptes de vices de

matière et de fabrication à l’acheteur initial pour une période de quatre-vingt-dix (90) jours à partir de la date d’achat

au détail.

Pour faire honorer la garantie: Présentez une preuve d’achat à l’atelier de réparations ou au distributeur agréé. Si

vous ne connaissez pas l’adresse de l’atelier de réparations ou du distributeur de votre région, appelez le 1-800-668-

1238. L’usine ne peut accepter le renvoi d’une machine complète si une autorisation n’a pas été accordée par écrit par

MTD PRODUCTS LIMITED.

Frais de transport: Les frais relatifs au transport de toute machine motorisée ou de tout accessoire sont à la charge

de l’acheteur. Les frais de transport d’une pièce quelconque envoyée à des fins de remplacement en vertu de cette

garantie doivent être prise en charge par l’acheteur, sauf si le renvoi de la machine est demandé par écrit par MTD

PRODUCTS LIMITED.

Autres garanties: Toutes les autres garanties, qu’elles soient expresses ou tacites, y compris les garanties tacites de

qualité marchande, se limitent à la durée stipulée dans cette garantie limitée expresse. Les conditions stipulées dans

cette garantie constituent le recours unique et exclusif quant aux obligations de MTD PRODUCTS LIMITED découlant

de la vente de ses produits.

MTD PRODUCTS LIMITED ne peut être tenue responsable pour toute perte ou tout dommage accidentel ou indirect.

GARANTIE LIMITÉE DE 4 ANS DES MOTEURS

Cette garantie limitée double la durée de la garantie limitée du fabricant du moteur qui accompagne la documentation

à l’intention du propriétaire.

12.08.06

Pour toute

réparation autre

que les ajustements

mineurs énuméré

ici, adressez-vous à

la station technique

agréée.

Dépannage

CauseProblème Solution

Le moteur ne

démarre pas.

Le moteur tourne

irrégulièrement.

1. Branchez et serrez le fil de la bougie.

2. Nettoyez la canalisation. Faites le plein

avec une essence propre et fraîche.

3. Débouchez l’évent.

4. Videz le réservoir à carburant. Faites

le plein avec une essence fraîche.

5. Consultez la notice d’utilisation du

moteur.

6. Consultez la notice d’utilisation du

moteur.

1. Fil de la bougie desserré.

2. La canalisation de carburant est bouchée

ou l’essence est eventée.

3. L’event du capuchon du réservoir est

bouché.

4. De l’eau ou une saleté est présente dans

le système.

5. Le filtre à air est sale.

6. Le carburateur est mal régle.

1. La poignée de commande de la lame n’est

pas embrayée.

2. Fil de la bougie débranché.

3. Le réservoir est vide ou l’essence est

éventée.

4. Moteur non amorcé.

5. La bougie est défectueuse.

6. Canalisation de carburant bouchée.

7. Le moteur est noyé.

1. Embrayez la poignée de commande de

la lame.

2. Branchez le fil à la bougie.

3. Faites le plein avec une essence propre

et fraîche.

4. Consultez la notice d’utilisation du

moteur.

5. Nettoyez, réglez l’écartement ou

replacez la bougie.

6. Nettoyez la canalisation.

7. Attendez quelques minutes avant

d’essayer de faire démarrer le moteur

Le moteur surchauffe.

1. Faites le plein d’huile du carter.

2. Consultez la notice d’utilisation du

moteur.

3. Démontez l’habitacle du ventilateur et

nettoyez-le.

4. Consultez la notice d’utilisation du

moteur.

1. Niveau d’huile trop bas.

2. Le filtre à air est sale.

3. La circulation d’air est gênée.

4. La carburateur est mal régle.

Le moteur hésite parfois à

régime élevé.

1. Réglez l’écartement à 0,030 po. Con-

sultez la notice d’utilisation du moteur

2. Consultez la notice d’utilisation du

moteur.

1. La bougie est sale, défectueuse ou

l’écartement est trop grand.

2. Le carburateur est mal réglé.

3. Le filtre à air est sale.

1. L’écartement de la bougie est trop petit.

2. Mélange du ralenti du carburateur mal

réglé.

Le moteur tourne

irrégulièrement.

1. Réglez l’écartement à 0,030 po ou

remplacez la bougie. Consultez la

notice d’utilisation du moteur.

2. Consultez la notice d’utilisation du

moteur.

3. Consultez la notice d’utilisation du

moteur.

Vibrations excessives.

1. Serrez la lame et l’adaptateur.

Équilibrez la lame.

2. Remplacez la lame.

1. La lame est desserrée ou mal équilibrée.

2. La lame est déformée.

La coupe est irrégulière

1. Placez les quatre roues à la même

hauteur.

2. Aiguisez ou remplacez la lame.

1. Les roues ne sont pas bien

positionnées.

2. La lame est émoussée.

La tondeuse ne

déchiquette pas l’herbe.

1. Ne tondez pas quand l’herbe est mouil-

lée. Attendez qu’elle sèche.

2. Coupez l’herbe à un réglage élevé, puis

tondez à nouveau à la hauteur voulue ou

sur une largeur plus étroite.

3. Aiguisez ou remplacez la lame.

1. L’herbe est mouillée.

2. L’herbe est trop haute.

3. La lame est émoussée.

Entretien

Portez toujours

des gants épais ou

utilisez un chiffon

épais pour manipuler

la lame en la démon-

tant pour l’aiguiser ou

la remplacer.

Si la lame est

déséquilibrée,

elle fera vibrer la

tondeuse de façon

excessive, mais elle

pourrait aussi causer

des dommages

à la tondeuse

ou même casser

pendant qu’elle

tourne, et causer de

sérieuses blessures à

l’utilisateur.

Figure 6-2

Entretien et remplacement de la lame

AVERTISSEMENT: Portez tou-

jours des gants épais ou utilisez

un chiffon épais pour manipuler

la lame en la démontant pour

l’aiguiser ou la remplacer.

Examinez périodiquement l’adaptateur de lame

pour y détecter tout fendillement éventuel, sur-

tout après avoir heurté un objet. Remplacez-le

au besoin. Procédez comme suit pour l’entretien

de la lame:

1. Débranchez toujours le fil de la bougie.

2. Basculez la tondeuse selon les instructions

dans la notice d’utilisation. S’il n’y a pas

d’instructions spécifiques, basculez la

tondeuse avec le filtre à air et le carburateur

sur le haut.

3. Enlevez le boulon et le support de la lame

qui maintiennent la lame et l’adaptateur sur le

vilebrequin. Voir la Figure 6-2.

4. Dégagez la lame et l’adaptateur du vilebre-

quin.

5. Pour l’affûter à nouveau, démontez-la puis

meulez ou limez les bords tranchants en

maintenant l’angle aussi près que possible du

biseau original. N’essayez pas d’aiguiser la

lame encore installée sur la tondeuse.

6. Il est essentiel que chaque tranchant soit

affûté également pour ne pas avoir une lame

déséquilibrée.

REMARQUE: Une lame déséquilibrée cause

des vibrations qui peuvent endommager le

moteur et la tondeuse. Assurez-vous de bien

rééquilibrer la lame après l’avoir aiguisée. Le

fabricant de la tondeuse ne peut être tenu

responsable des dégâts causés par le mauvais

équilibre de la lame.

REMARQUE: Démontez toujours la lame de

son adaptateur pour vérifiez son bon équilibre.

7. Vous pouvez vérifier l’équilibre de la lame

en la plaçant sur un tournevis à tige ronde.

Limez le métal du côté le plus lourd jusqu’à

ce que la lame soit parfaitement équilibrée.

8. Avant de remonter la lame et son adaptateur

sur la tondeuse, lubrifiez le vilebrequin et la

surface intérieure de l’adaptateur avec une

huile légère.

9. Placez l’adaptateur de la lame sur le vilebre-

quin, «l’étoile» à l’opposé du moteur. Voir la

Le fait de couper

l’herbe sur un sol

sablonneux provoque

l’usure de la lame par

abrasion.

Figure 6-2. Placez la lame, le côté sur lequel

la mention «Bottom» (ou le numéro de pièce)

apparaît, à l’opposé de l’adaptateur. Alignez

le support de la lame sur celle-ci en enfon-

çant les pattes dans les trous de la lame, puis

insérez le boulon hex.

10. Serrez le boulon hex. au couple recom-

mandé ci-dessous:

Couple de montage de la lame

Boulon centrale 450 po-lb min., 600 po-lb max.

Vérifiez périodiquement que TOUS les écrous et

boulons de la machine sont bien serrés.

Remisage hors saison

Procédez de la manière suivante pour préparer

votre tondeuse pour un entreposage prolongé.

1. Nettoyez et lubrifiez soigneusement la

tondeuse selon les instructions de lubrifica-

tion.

2. L’utilisation d’un nettoyeur sous pression

ou d’un boyau d’arrosage pour nettoyer la

tondeuse est déconseillée.

3. Consultez la notice d’utilisation du moteur

quant aux instructions d’entreposage du

moteur.

4. Enduisez la lame de la tondeuse d’une

graisse à châssis pour l’empêcher de rouiller.

5. Entreposez la tondeuse dans un endroit sec

et propre. Ne la remisez pas près de produits

corrosifs, comme des engraise.

REMARQUE: Il est très important de bien

protéger le matériel contre la rouille s’il doit être

entreposé dans un abri métallique non ventilé.

Enduisez toute la machine, en particulier les

câbles et toutes les pièces mobiles, avec une

huile légère ou de la silicone.

AVERTISSEMENT

La page charge ...

Bolens 11A-109Q565 Le manuel du propriétaire

Marque: Bolens

Modèle: 11A-109Q565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 11A-109Q565 Owner's manual

Bolens 11A-109Q565 Le manuel du propriétaire

Bolens 11A-109Q565 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents