Simplicity 020667-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
This pressure washer is rated in accordance to the Pressure Washer
Manufacturers Association (PWMA) standard PW101-2010 (Testing
and Rating Performance of Pressure Washers).
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80022989 Revision A
Electric Pressure Washer
OPERATOR’S MANUAL
POWERflow+ TECHNOLOGY
™
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® electric pressure washer. We are pleased that you’ve
placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this
manual, your Briggs & Stratton electric pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with electric pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this electric
pressure washer could be used for, it is important that you read and understand these instructions thoroughly before
attempting to start or operate this equipment. Save these original instructions for future reference.
This electric pressure washer requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your electric pressure washer. Consult
your Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at
BRIGGSandSTRATTON.COM.
Electric Pressure Washer
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ___________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON is a registered
trademark of Briggs & Stratton Corporation.
Table of Contents
Operator Safety.............................. 3
Assembly................................... 6
Features and Controls ........................ 8
Operation................................... 9
Maintenance ...............................12
Storage ...................................13
Troubleshooting ............................14
Warranty ..................................15
Specifications ..............................16
Register Your Product
To ensure prompt and complete warranty coverage, register your product online at www.onlineproductregistration.com.
3
Operator Safety
SAVE THESE INSTRUCTIONS
Equipment Description
Every effort has been made to ensure that the information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve the
product and this document at any time without prior notice.
This ISM device complies with Canadian ICES-001.
POWERflow+ Technology
POWERflow+ Technology is a deep cleaning pressure washer
with both high pressure to lift dirt AND high flow to easily wash
it away. In the high flow mode, POWERflow+ Technology
enhances the cleaning experience by providing extended
reach, power soaping, and faster rinsing capabilities.
The force behind POWERflow+ is in the pump with two
separate cleaning modes: high pressure and high flow.
The high-pressure mode delivers up to 2000 PSI (pounds
square inch) and is ideal for cleaning the toughest stains,
mildew and grime from decks, driveways and siding, while
the high-flow mode delivers up to 3.5 GPM (gallons per
minute) to power-rinse away dirt, soap and debris. The
high flow mode also makes it the best to use for washing
delicate surfaces such as patio furniture, vehicles, and
children’s outdoor play sets and toys.
Briggs & Stratton’s POWERflow+ Technology is a system
of components working in concert to deliver the high-flow
capability. Water is sent from the pump to the specially
designed 26 ft. hose and into the custom-engineered
POWERflow+ gun with soft grip handle. Water then flows
into the exclusive 7-in-1 nozzle that allows user to change
from High Pressure to High Flow, without changing nozzle
tips, and propels the stream up to 30 ft.
Ground Fault Circuit Interrupter Protection
This pressure washer is provided with a ground-fault
circuit-interrupter (GFCI) built into the plug of the power
supply cord. This device provides additional protection
from the risk of electric shock. Should replacement of
the plug or cord become necessary, use only identical
replacement parts that include GFCI protection.
Automatic Shut-Off
The electric pressure washer is equipped with a sensor that
will detect that water flow has stopped when releasing the
spray gun trigger. The sensor will cause the motor to shut off
for as long as the spray gun trigger is released.
If the motor continues to run when the spray gun trigger is
released or locked, DO NOT USE THE MACHINE. Call the
electric pressure washer helpline at (800) 743-4115 for
assistance.
NOTICE The electric pressure washer is equipped with a
main power ON/OFF switch. The switch should always be
moved to the OFF position (0) when the electric pressure
washer is not being used to prevent possible damage.
Motor Overload
The electric motor in this electric pressure washer is
equipped with an overload protection device (thermostat).
This device will automatically shut off the motor if the motor
overheats or draws excessive current.
If the overload protection device is tripped, disconnect the
power supply by turning the master ON/OFF switch to the
OFF (0) position. Let unit cool for 30 minutes. Then turn
the master ON/OFF switch to the ON (I) position to resume
operation.
Important Safety Information
Please read and understand this entire manual before
attempting to assemble, operate or service the product.
Follow the maintenance instructions specified in this
manual. If you have any questions regarding the product,
please call customer service at (800) 743-4115, 8 a.m. -
5 p.m., CST, Monday - Friday.
Safety Symbols and Meanings
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol
may be used to represent the type of hazard. The signal
word NOTICE indicates information considered important,
but not hazard-related.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates information considered important, but
not hazard-related.
WARNING Failure to read and follow the operator’s
manual and all operating instructions before
using could result in death or serious injury.
• Read this manual carefully and become familiar with
your electric pressure washer. Know its applications, its
limitations, and any hazards involved.
Chemical Burn
Electrical Shock
Slippery Surface Fall
Flying Objects
Read Manual
Projectile
Fluid Injection
Fire
4 BRIGGSandSTRATTON.COM
WARNING Use of electric pressure washer could
create puddles and slippery surfaces.
Risk of kickback. Spray gun could
kickback causing you to fall resulting in
death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
• The cleaning area should have adequate slopes
and drainage to reduce the possibility of a fall due to
slippery surfaces.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• NEVER aim spray gun at people, animals, or plants.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
WARNING Risk of eye or bodily injury. Spray could
splash back, propel objects or cause
internal harm resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment. NEVER substitute safety
glasses or dry-condition goggles for indirect vented
safety goggles.
• Know how to stop the pressure washer and bleed
pressure quickly. Be thoroughly familiar with the
controls.
• DO NOT allow CHILDREN to operate the electric
pressure washer.
• Keep operating area clear of all persons.
• Inspect high pressure hose before each use. NEVER
repair high pressure hose; replace it.
• DO NOT repair leaking connections with sealant of any
kind; replace o-rings and gaskets.
• Keep hose connected to electric pressure washer and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction while system
is pressurized and squeeze spray gun trigger to release
high pressure, every time you turn off the pressure
washer.
• DO NOT aim spray gun at people or animals.
• DO NOT
drink from hose connected accessories.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while the electric
pressure washer is in ON (I) position.
• DO NOT use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun and accessories are
correctly attached.
• Stay alert – watch what you are doing.
• DO NOT operate the product when fatigued or under
the influence of alcohol or drugs.
• Close supervision is necessary when this product is
used near children.
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
WARNING Risk of electrocution. Contacting both
power conductors, at the same time could
cause electric shock or burn resulting in death
or serious injury.
• Connect only to a properly grounded outlet. DO NOT
remove ground pin from plug.
• Inspect cord before each use, DO NOT use if cord is
damaged.
• The product is equipped with a ground fault circuit
interrupter (GFCI) built into the power cord plug. If
replacement of the plug or cord is required, use only
identical replacement parts.
• Keep all connections dry and off the ground.
• DO NOT touch plug with wet hands.
• DO NOT run cord through doorways, windows, holes in
ceilings, walls, or floors.
• DO NOT walk on cord.
• DO NOT drive over, drag or place objects over cord.
• DO NOT spray near power source.
5
WARNING Risk of fire. Spraying flammable liquids
could result in death or serious injury.
• DO NOT spray flammable liquids.
WARNING Risk of fire. Overheated cord could result
in death or serious injury.
• Uncoil cord completely prior to use.
• DO NOT cover cord with any material.
WARNING This product contains lead and lead
compounds, known to the State of California to cause
birth defects or other reproductive harm. Wash your
hands after handling this product.
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using 0° nozzle
setting or red nozzle.
• NEVER aim spray gun at plants.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and render your unit inoperable.
• Freeze damage is not covered under warranty.
NOTICE Improper treatment of electric pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact authorized service center.
• DO NOT operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on the electric
pressure washer.
• DO NOT modify the electric pressure washer in any
way.
• DO NOT move the electric pressure washer by pulling
on hoses. Move unit using the transport handle
supplied.
• Use ONLY branded accessories intended for use with
this product.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting
in death or serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure
washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
6 BRIGGSandSTRATTON.COM
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
electric pressure washer.
Your electric pressure washer requires some assembly
but is quickly ready for use. If you have any problems with
the assembly of your electric pressure washer, please call
the electric pressure washer helpline at (800) 743-4115. If
calling for assistance, please have the model, revision, and
serial number from the identification label available.
Unpack Electric Pressure Washer
1. Remove everything from carton.
2. Raise handle (A) to upright position by pulling up latch
on each side of handle. Push latches (B) down to
secure handle in place.
NOTICE The unit is equipped with a foldable handle. The
handle can be folded down for storage. See Final Storage
Procedures.
3. Ensure you have all included items prior to assembly.
Items Included in the Carton
• Main unit
• Operator’s manual
• Spray gun
• High pressure hose
• Spray wand with Quick Connect (QC)
• 7-in-1 nozzle
• Red high pressure nozzle
Check all contents. If any parts are missing or damaged, call
the electric pressure washer helpline at (800) 743-4115.
Become familiar with each component before assembling
the electric pressure washer. Identify contents with the
illustration shown in Features and Controls.
Lubricate O-Rings
Lubrication of o-rings is extremely important for installation
and operation. The use of a lubricant (petroleum or
synthetic grease) during assembly helps seat o-rings
properly and provides an improved seal. It also helps
protect the o-ring from damage by abrasion, pinching or
cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant on
o-rings prior to assembling the garden hose to the pump
(C), high pressure hose (D), spray wand (E) and spray
gun (F).
Lubricate all connections shown below, following these
instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light film
is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible (QC
fitting, M22 fitting).
E
D
F
C
A
B
B
7
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water supply
connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
1. Uncoil high pressure hose (A) and attach black end of
hose to base of spray gun (B). Tighten by hand.
2. Attach blue end of high pressure hose (A) to high
pressure outlet (C) on pump. Tighten by hand.
3. Run water through your garden hose for 30 seconds
to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F (38°C)).
4. Before connecting garden hose (D) to water inlet (E),
inspect inlet screen (F). Clean screen if it contains
debris or have it replaced if damaged. DO NOT run
pressure washer if inlet screen is damaged.
NOTICE Using a One Way Valve (vacuum breaker or
check valve) at pump inlet could cause pump or inlet
connector damage.
• There MUST be at least 10 ft. (3 m) of unrestricted
garden hose between the pressure washer inlet and any
device, such as a vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (D) (not to exceed 50 ft. (15
m) in length) to the water inlet (E). Tighten by hand.
Connect Spray Wand and 7-in-1 Nozzle
1. Turn ON water, point gun in a safe direction, press
trigger lock button (G), then squeeze trigger to purge
pump system and spray gun of air and impurities.
2. Attach spray wand to spray gun. Tighten by hand.
3. Pull back on collar of spray wand, insert 7-in-1 nozzle
and release collar. Tug on 7-in-1 nozzle to make sure
it is securely in place. See How to Use Nozzles.
Checklist Before Starting Pump Motor
Review the unit’s assembly to ensure you have performed
all of the following.
1. Be sure to read Operator Safety and Operation before
using the electric pressure washer.
2. Check for properly tightened hose connections.
3. Check to make sure there are no kinks, cuts, or
damage to hoses.
4. Provide a proper water supply at an adequate flow.
5. Plug electrical power cord into a dedicated electrical
circuit rated for 120 Volts AC at 15 Amps that is
properly installed in accordance with all local codes and
ordinances. Check that circuit is not used to supply any
other electrical needs.
G
A
C
B
A
F
D E
8 BRIGGSandSTRATTON.COM
Features and Controls
Read the Operator’s Manual and safety rules before operating your electric pressure washer.
Compare the illustrations with your electric pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this original manual for future reference.
A - Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock.
B - Identification Label — Provides model and serial
number of pressure washer. Please have these readily
available if calling for assistance.
C - Electric Cord with GFCI — The electric pressure
washer and operator is protected by a ground fault circuit
interrupter (GFCI).
D - High Pressure Hose — Connect one end to high
pressure water outlet and the other end to spray gun.
E - Spray Wand with Quick Connect — Allows you to
switch between 7-in-1 nozzle and optional accessories.
F - Detergent Tank — Use to hold up to 40 fl. oz. (1.2 l) of
pressure washer safe detergent.
G - Water Supply Inlet — Connect to water supply using
a 50 ft. (15.24 m) maximum garden hose.
H - Master ON/OFF Toggle Switch — Turn switch to ON
(I) position to start pressure washer. Turn switch to OFF (0)
position to stop pressure washer.
J - High Pressure Outlet — Connection for high pressure
hose.
K - 7-in-1 Nozzle — Contains seven different spray
pattern nozzles for various applications.
L - Warning Label — Identifies hazards to be avoided
when using your pressure washer.
K
L
E
F
D
H
G
J
C
B
A
9
Operation
How to Start Your Electric Pressure Washer
Follow the instructions below in the order presented. If
you have any problems operating your electric pressure
washer, please call the electric pressure washer helpline at
(800) 743-4115.
1. Place the electric pressure washer near an outside
water source capable of supplying water at a flow rate
greater than 5.0 gallons per minute (18.9 l) and 25-75
psi (1.72-5.17 bar) at the electric pressure washer end
of garden hose. DO NOT siphon supply water.
2. Connect garden hose to water inlet.
3. Check that high pressure hose is tightly connected to spray
gun and high pressure outlet. See Assembly section.
NOTICE If hose connections start leaking during use,
shut down unit as described in steps 1-5 of How to Stop
Your Electric Pressure Washer. Remove hose completely
and reinstall hand tight. Failure to completely remove
hose could damage o-ring and cause hose connection to
continue leaking. If o-ring becomes damaged, replace.
NOTICE DO NOT run the pump without the water supply
connected and turned on.
• Damage to equipment resulting from failure to follow
this instruction will void warranty.
4. Turn ON water, point gun in a safe direction, press
trigger lock button and squeeze trigger to purge pump
system of air.
5. Install spray wand and 7-in-1 nozzle onto spray gun.
See Assembly section.
NOTICE The unit can be operated in vertical or horizontal
positions.
6. Turn master ON/OFF switch (A) to OFF (0) position.
7. Plug electrical power cord into a dedicated electrical
circuit rated for 120 Volts AC at 15 Amps that is
properly installed in accordance with all local codes and
ordinances. Circuit is not to supply any other electrical
needs. The indicator light on the GFCI should be ON.
NOTICE The indicator light must be ON for the electric
pressure washer to operate.
8. Press TEST button (B). The indicator light (C) should
be OFF.
9. Press RESET button (D). The indicator light (C)
should be ON.
NOTICE DO NOT use the electric pressure washer if
above test fails.
10. Turn master ON/OFF switch to ON (I) position.
11. Point gun in a safe direction, press trigger lock button
and squeeze trigger.
The electric pressure washer motor will start and stop as
spray gun trigger is depressed and released.
The electric pressure washer is now ready for use.
Instructions for use of the supplied accessories are given
later in this section.
B
D
C
A
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
WARNING Risk of electrocution. Non-operating
ground fault circuit interrupter (GFCI) could
result in death or bodily injury. If indicator light
does not stay ON after test and reset, do not
use GFCI.
WARNING Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
10 BRIGGSandSTRATTON.COM
How to Stop Your Electric Pressure Washer
The electric pressure washer motor runs only when the
trigger is engaged. To stop the electric pressure washer
and turn off the motor:
1. Release spray gun trigger.
2. Turn master ON/OFF switch to OFF (0) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze trigger to relieve built
up pressure in the unit.
5. Disconnect GFCI plug from outlet.
How to Use Nozzles
7-in-1 Nozzle
The 7-in-1 nozzle allows you to switch between seven
different spray pattern nozzles. Release trigger on spray
gun to engage safety lock before changing spray patterns.
The spray patterns vary as shown below.
1. Select desired spray pattern:
• Select Maximum 0° nozzle setting for stubborn or
hard to reach surface such as second story surfaces,
paint removal, oil stains, rust removal or other
stubborn substances (tar, gum, grease, wax, etc.).
• Select General 15° nozzle setting for tougher
cleaning tasks. Ideal for removing grease and dirt
from hard surfaces. Also capable of stripping paint
when held at a 45° angle.
• Select Gentle 40° nozzle setting for gentle cleaning
of cars/trucks, boats, RV’s, patio furniture, lawn
equipment, etc.
• Select Fan Spray nozzle setting for optimal high
flow rinsing away of light dirt and debris.
• Select Fan Spray with Soap nozzle setting for
delicate surface cleaning of cars, trucks, childrens
play equipment, patio furniture, etc.
• Select Extended Reach nozzle setting for quick
high flow clean up and long reach cleaning of
second story siding and windows.
• Select Extended Reach with Soap nozzle setting to
propell soap to second story siding and windows.
2. Turn dial until desired spray pattern lines up with
arrow on 7-in-1 nozzle.
Red High Pressure Nozzle
The red high pressure nozzle gives you the most cleaning
power by producing the highest pressure.
Usage Tips
• For most effective cleaning, keep nozzle from 8 to
24 inches away from cleaning surface.
• If you get too close, especially using a high pressure
spray pattern nozzle, you may damage surface being
cleaned.
• Do Not get closer than 6 inches (15 cm) when
cleaning tires.
0˚ 15˚40˚
Maximum General Gentle Fan Spray Fan Spray
with Soap
Extended Reach Extended Reach
with Soap
High Pressure Mode
High Flow Mode
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
11
Applying Detergent
To apply detergent, follow these steps:
1. Review use of nozzles shown in How to Use Nozzles.
2. Prepare your detergent solution as required by job to
be performed.
3. Remove cap from detergent tank and fill with
detergent solution. Replace cap.
4. Make sure one of the soap spray pattern nozzles is
selected on 7-in-1 nozzle.
NOTICE Detergent cannot be applied with high pressure
nozzles (red, maximum, general, delicate, fan spray or
extended reach).
5. Make sure garden hose is connected to water inlet
and high pressure hose is connected to spray gun and
high pressure outlet. Turn on water.
6. Start the pressure washer as instructed in How to
Start Your Electric Pressure Washer.
7. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward using
long, even, overlapping strokes.
NOTICE High water supply pressure may not allow
detergent to flow. See Troubleshooting.
8. Allow detergent to “soak in” for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. To prevent streaking, Do Not
allow detergent to dry on surface.
Electric Pressure Washer Rinsing
1. Select desired high pressure nozzle following
instructions How to Use Nozzles.
2. Keep spray gun a safe distance from area you plan to
spray.
3. Apply a high pressure spray to a small area and then
check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.
4. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Other Cleaning Tips
• NEVER leave the electric pressure washer unattended
while it is plugged into an electrical outlet and while
water is supplied to the equipment.
• If you have the nozzle too far away from the surface
being washed, the cleaning may not be as effective.
How to Store Accessories
The unit is equipped with places to store your high
pressure hose, spray gun, spray wand, 7-in-1 nozzle and
power cord. The red high pressure nozzle can be stored
on end of spray wand. Identify all accessories with the
illustrations in Features and Controls.
WARNING Chemical Burn Hazard.Chemicals could
cause burns resulting in death or serious
injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING Risk of kickback.
Spray gun could kickback causing you to fall
resulting in death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
12 BRIGGSandSTRATTON.COM
Maintenance
General Recommendations
Regular maintenance will improve the performance and
extend the life of the electric pressure washer.
The electric pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty, the
operator must maintain the electric pressure washer as
instructed in this manual, including proper storage.
NOTICE Should you have questions about replacing
components on your electric pressure washer, please call
(800) 743-4115 for assistance.
NOTICE Your electric pressure washer was designed
and intended to be used with POWERflow+ components
ONLY. Using components that are not designed for
POWERflow+ will cause your pressure washer to not
function optimally.
Before Each Use
1. Clean debris.
2. Check water inlet screen for debris or damage.
3. Check high pressure hose for leaks.
4. Check spray gun operation.
Electric Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from electric
pressure washer. Inspect cooling air slots and openings on
the front, rear and bottom of the electric pressure washer.
These openings must be kept clean and unobstructed.
The electric pressure washer parts should be kept clean to
reduce the risk of overheating and ignition of accumulated
debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of the electric pressure
washer can damage it and/or shorten its life.
• DO NOT insert any objects through cooling slots.
Check and Clean Water Inlet Screen
Examine the screen on the unit’s water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging of
cover, damage or movement of couplings. If any of these
conditions exist, replace the hose immediately.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
Check Spray Gun
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing trigger lock button
and making sure trigger “springs back” into place when
you release it. You should not be able to press trigger
without pressing trigger lock button. Replace spray gun
immediately if it fails any of these tests.
Nozzle Maintenance
Excessive pump pressure can cause a pulsing sensation
felt while squeezing the spray gun trigger. The principal
cause of excessive pump pressure is a nozzle clogged or
restricted with foreign materials such as dirt, etc. A clogged
nozzle could lead to pump cycling ON/OFF or not turning
on even when there is some flow.
To correct the problem, immediately clean the nozzle by
following these instructions:
1. Turn master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
2. Disconnect water supply at the electric pressure
washer.
3. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze spray gun trigger to
release retained high water pressure.
4. Remove 7-in-1 nozzle from end of spray wand.
5. Use small paper clip to free any foreign material
clogging or restricting any of the nozzles.
6. Using a garden hose, remove additional debris by
back flushing water through spray wand. Back flush
between 30 to 60 seconds.
7. Reinstall 7-in-1 nozzle into spray wand.
8. Reconnect spray wand to spray gun.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
13
9. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray
gun. Turn on water.
10. Plug power cord into electrical outlet and turn master
ON/OFF switch to pressure washer ON (I) position.
11. Test the electric pressure washer by operating with
each nozzle setting.
Pump and Motor Maintenance
The electric pressure washer does not require any
maintenance to the pump or motor. Both assemblies
are pre-lubricated and sealed, requiring no additional
lubrication ever.
After Each Use
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and
“freeze” pump action. Follow these procedures after every
use:
1. To ensure detergent tank does not drain during
storage, run electric pressure washer with a soap
spray nozzle until tank is empty.
2. Add 0.5 liter of clean fresh water to detergent tank, run
electric pressure washer with a soap nozzle. Flush for
one or two minutes.
3. Turn master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
4. Turn off water supply. Point gun in a safe direction,
press trigger lock button and squeeze trigger to relieve
trapped pressure.
5. Disconnect garden hose from water inlet. Disconnect
high pressure hose from spray gun and high pressure
outlet.
6. Drain water from hose and spray gun, then use a cloth
or equivalent to wipe off all exterior surfaces.
7. Drain water from pump by tipping unit onto its right
side (water inlet and high pressure outlet facing down)
for two minutes.
8. Wrap high pressure hose and power cord on hook.
9. Store spray gun, spray wand, and 7-in-1 nozzle in
provided storage areas. Store red high pressure
nozzle on end of spray wand.
10. Store unit in a clean, dry area.
11. If storing for more than 30 days see Winter or Long
Term Storage.
Winter or Long Term Storage
Follow steps 1-9 in After Each Use.
NOTICE Water left in pump could freeze and permanently
damage pump. Freeze damage is not covered under
warranty.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039, to treat
pump. This prevents freeze damage and lubricates plunger
and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the electric pressure
washer. Contact the nearest authorized service center to
purchase Pump Saver.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and render your unit inoperable.
• Freeze damage is not covered under warranty.
To use PumpSaver, make sure electric pressure washer
is turned off and inlet and outlet hoses are disconnected.
Read and follow all instructions and warnings given on the
PumpSaver container.
Final Storage Procedures
1. Wrap high pressure hose and power cord on hook.
2. Store spray gun, spray wand, and 7-in-1 nozzle in
provided storage areas. Store red high pressure
nozzle on end of spray wand.
3. Store unit in a clean, dry area that is protected from
freezing temperatures. The unit is equipped with a
foldable handle. The handle can be folded down
for storage. The unit can be operated in vertical or
horizontal positions.
4. Cover unit with a suitable protective cover that does
not retain moisture.
14 BRIGGSandSTRATTON.COM
Troubleshooting
Problem Cause Correction
Pump has following problems:
failure to produce pressure,
erratic pressure, chattering,
loss of pressure, low water
volume.
1. Water inlet is blocked.
2. Inadequate water supply.
3. Garden hose is kinked or leaking.
4. Clogged water inlet screen.
5. Water supply is over 100°F
(38°C).
6. High pressure hose is blocked or
leaks.
7. Nozzle is obstructed.
1. Clear inlet.
2. Provide adequate water flow.
3. Straighten garden hose or replace if
leaking.
4. Check and clean water inlet screen.
5. Provide cooler water supply.
6. Clear blocks in high pressure hose or
replace hose.
7. Clean spray tip.
Unit fails to start when spray
gun trigger is squeezed.
1. Water supply is not turned on.
2. Unit is not turned on.
3. Garden hose is too long.
4. Fuse blown or circuit breaker
tripped.
1. Turn on water supply.
2. Turn master ON/OFF switch to ON (I)
position. Reset GFCI.
3. Use only 50 ft. (15.24 m) maximum
garden hose.
4. a.) Check fuse box for blown fuse and
replace as necessary or reset circuit
breaker. Do not use a fuse or circuit
breaker with a higher rating than that
specified for your particular branch
circuit.
b.) Disconnect other electrical
appliances and turn off lights in the
circuit or operate the pressure washer
on its own dedicated circuit.
c.) Run pressure washer in any
POWERflow+ High Flow Mode (
)
nozzle setting for 10 minutes. Motor
break in may be necessary.
Detergent fails to mix with
spray.
1. High pressure or high flow without
soap nozzle is selected.
2. Inlet water supply pressure too
high.
1. Select a high flow soap nozzle setting
(indicated with bubbles).
2. Slowly close water supply valve until
chemical just starts to draw (soap suds
will appear when chemical starts to
draw).
Hose connections leaking.
1. Garden hose loose to water inlet.
2. Loose high pressure hose
connections.
3. Damaged o-ring.
1. Hand tighten garden hose to water
inlet.
2. Remove hose completely and reinstall
hand tight.
3. Replace o-ring.
For all other issues, see a Briggs & Stratton authorized dealer.
15
80018419_EN Rev A
BRIGGS & STRATTON WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject
to the time periods and conditions stated below. For warranty service, contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the internet at
BRIGGSANDSTRATTON.COM.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is permitted
by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state or country to country.**
WARRANTY PERIOD
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial use, it
shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will
be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty covers only defects in materials or
workmanship. It does not cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are not
covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration. Attachments
or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in place of utility
power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or engines. This
warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
12 months None
16 BRIGGSandSTRATTON.COM
Product Specifications
Max Outlet Pressure ................2,000 PSI (138 BAR)* @ 1.1 GPM (4.1 liters/min)
Max Flow Rate ..................... 3.5 GPM* (13.25 liters/min)* @ 80 PSI (5.5 BAR)
Detergent Mix ...........................................See MFR’s Instructions
Water Supply Temperature ............................ Not to exceed 100°F (38°C)
Motor ......................................................... Induction Type
Rated Voltage ....................................................120 Volts AC
Current............................................................13.0 Amps
Briggs & Stratton Corporation
P.O. Box 702
Milwaukee, Wisconsin, 53201-0702 U.S.A.
(800) 743-4115
Electric Pressure Washer
*
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard
PW101-2010 (Testing and Rating Performance of Pressure Washers).
Esta hidrolavadora está clasificada de acuerdo a la norma PW101-2010 (Pruebas
y valoración de rendimiento de hidrolavadoras) de la Asociación de Fabricantes de
Hidrolavadoras (PWMA, Pressure Washer Manufacturers Association).
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, EE. UU.
Hidrolavadora eléctrica
MANUAL DEL OPERADOR
POWERflow+ TECHNOLOGY
™
2 BRIGGSandSTRATTON.COM
Gracias por comprar esta hidrolavadora eléctrica Briggs & Stratton® de alta calidad. Nos complace que haya depositado
su confianza en la marca Briggs & Stratton. Si la operación y el mantenimiento de su producto Briggs & Stratton se realiza
según las instrucciones de este manual, le proporcionará muchos años de servicio confiable.
Este manual contiene información de seguridad para alertarlo sobre los peligros y riesgos asociados con las
hidrolavadoras eléctricas, y para indicarle cómo evitarlos. Dado que Briggs & Stratton no conoce necesariamente todas
las aplicaciones para las cuales se podría utilizar esta hidrolavadora eléctrica, es importante que usted lea detalladamente
y entienda estas instrucciones antes de hacer arrancar o utilizar este equipo. Guarde estas instrucciones originales
para futuras consultas.
Esta hidrolavadora eléctrica requiere su montaje final antes de su uso. Consulte la sección Montaje de este manual
para conocer las instrucciones sobre los procedimientos de montaje final. Siga las instrucciones detalladamente.
Contacto
Nunca debe ir demasiado lejos para encontrar el soporte y el servicio de Briggs & Stratton para su hidrolavadora eléctrica.
Consulte las Páginas Amarillas. Existen más de 30.000 distribuidores de servicio autorizado por Briggs & Stratton en todo
el mundo, quienes suministran servicio de calidad. También puede ponerse en contacto con Atención al Cliente de Briggs
& Stratton por teléfono al (800) 743-4115 o en Internet en BRIGGSandSTRATTON.COM.
Hidrolavadora eléctrica
Número de modelo __________________________
Revisión __________________________________
Número de serie ____________________________
Fecha de compra __________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. Reservados todos los derechos.
BRIGGS & STRATTON es una marca
registradas de Briggs & Stratton Corporation.
Índice
Seguridad del operador . . . . . . . . . . . . . . . . . . . . . . . 3
Montaje .................................... 6
Características y controles.....................9
Operación .................................. 9
Mantenimiento .............................12
Almacenamiento............................13
Solución de problemas.......................14
Garantía...................................15
Especificaciones............................16
Registrar su producto
Para asegurar pronta y completa cobertura de la garantía, registre su producto en línea en
www.onlineproductregistration.com.
3
Seguridad del operador
CONSERVE ESTAS INSTRUCCIONES
Descripción del equipo
Se ha realizado el máximo esfuerzo para reunir en este
manual la información más precisa y actualizada. No
obstante, nos reservamos el derecho de modificar, alterar
o mejorar de cualquier otra forma el producto y este
documento en cualquier momento y sin previo aviso.
Este dispositivo ISM cumple con la norma canadiense ICES-001.
POWERflow+ Technology
POWERflow+ Technology es una hidrolavadora de limpieza
profunda que funciona con alta presión para levantar la
suciedad Y alto flujo para quitarla fácilmente. En el modo de
alto flujo, POWERflow+ Technology mejora la experiencia
de limpieza al proporcionar capacidades de mayor alcance,
enjabonado automático y enjuague más rápido.
La fuerza detrás de POWERflow+ se encuentra en la
bomba con dos modos de limpieza separados: alta presión
y alto flujo. El modo de alta presión proporciona hasta 2,000
psi (libras por pulgada cuadrada) y es ideal para la limpieza
de las manchas más resistentes, el moho y la suciedad de
terrazas, calzadas y revestimientos, mientras que el modo
de alto flujo ofrece hasta 3.5 gpm (galones por minuto) para
poder enjuagar la suciedad, el jabón y los residuos. El modo
de alto flujo también es mejor utilizado para el lavado de
superficies delicadas, como muebles de jardín, vehículos, y
juegos y juguetes de exterior para niños.
POWERflow+ Technology de Briggs & Stratton es un
sistema de componentes que trabajan en conjunto para
ofrecer la capacidad de alto flujo. El agua se envía desde
la bomba a la manguera especialmente diseñada de 26
pies y a la pistola POWERflow+ de diseño personalizado
y con mango de agarre suave. El agua pasa entonces a la
exclusiva boquilla 7-en-1 que permite al usuario cambiar
de alta presión a alto flujo, sin cambiar las boquillas, e
impulsa el chorro hasta 30 pies.
Protección mediante el interruptor de circuito por
fallos con conexión a tierra
Esta hidrolavadora está cuenta con un interruptor de
circuito por fallos con conexión a tierra (GFCI, ground-fault
circuit-interrupter) montado en el enchufe del cable de
alimentación. Este dispositivo proporciona una protección
adicional contra el riesgo de descarga eléctrica. En
caso de que sea necesario reemplazar el enchufe o el
cable, utilice solamente piezas de repuesto idénticas que
incluyan la protección de GFCI.
Apagado automático
La hidrolavadora eléctrica está equipada con un sensor
que detecta que el flujo de agua se ha detenido al liberar o
bloquear el gatillo de la pistola de pulverización. El sensor
hará que el motor se apague durante el tiempo que el gatillo
de la pistola de pulverización esté liberado o bloqueado.
Si el motor sigue funcionando cuando el gatillo de la pistola
de pulverización está liberado o bloqueado, NO UTILICE
LA MÁQUINA. Llame a la línea directa para hidrolavadoras
eléctricas al (800) 743-4115 para obtener ayuda.
AVISO La hidrolavadora eléctrica está equipada con un
interruptor principal de encendido/apagado. El interruptor
siempre debe moverse a la posición de apagado (0)
cuando la hidrolavadora eléctrica no se está usando para
evitar posibles daños.
Sobrecarga del motor
El motor eléctrico de esta hidrolavadora eléctrica está equipado
con un dispositivo de protección de sobrecarga (termostato).
Este dispositivo apagará automáticamente el motor si este se
sobrecalienta o en caso de exceso de corriente.
Si se activa el dispositivo de protección de sobrecarga,
desconecte la fuente de alimentación moviendo el
interruptor principal de encendido/apagado a la posición
de apagado (0). Deje que la unidad se enfríe durante 30
minutos. A continuación, mueva el interruptor principal de
encendido/apagado a la posición de encendido (I) para
reanudar el funcionamiento.
Información importante de seguridad
Lea y comprenda todo el manual antes del montaje, la
operación o el mantenimiento del producto. Siga las
instrucciones de mantenimiento especificadas en este
manual. Si tiene alguna pregunta relacionada con el
producto, llame a Atención al Cliente al (800) 743-4115,
de lunes a viernes, de 8 a. m. a 5 p. m., CST.
Símbolos de seguridad y significados
El símbolo de alerta de seguridad indica un posible
riesgo para su integridad física. Se utiliza una palabra de
señalización (PELIGRO, ADVERTENCIA o PRECAUCIÓN)
junto con el símbolo de alerta para designar un grado o
nivel de gravedad de riesgo. Se puede utilizar un símbolo
de seguridad para representar el tipo de riesgo. AVISO
indica una información considerada importante, pero no
relacionada con un peligro potencial.
PELIGRO indica un peligro que, si no se evita,
ocasionará la muerte o lesiones graves.
ADVERTENCIA indica un peligro que, si no se evita,
podría ocasionar la muerte o lesiones graves.
PRECAUCIÓN indica un peligro que, si no se evita,
podría ocasionar lesiones menores o moderadas.
AVISO indica una información considerada importante, pero
no relacionada con un peligro potencial.
ADVERTENCIA No leer ni seguir las instrucciones del
manual del operador y todas las instrucciones de
funcionamiento antes de usar la unidad podría
ocasionar la muerte o lesiones graves.
• Lea este manual cuidadosamente y familiarícese con la
hidrolavadora eléctrica. Conozca sus aplicaciones, sus
limitaciones y los peligros involucrados.
Quemadura
química
Descarga eléctrica
Superficie
resbaladiza
Caídas
Objetos
voladores
Lea el manual
Proyectil
Inyección
de fluidos
Fuego
4 BRIGGSandSTRATTON.COM
ADVERTENCIA El uso de la hidrolavadora eléctrica
podría formar charcos y generar
superficies resbaladizas.
Riesgo de contragolpe. La pistola de
pulverización podría causar un contragolpe, con riesgo de
caída que podría provocar la muerte o lesiones graves.
• Opere la hidrolavadora eléctrica desde una superficie
estable.
• No se estire ni se pare sobre un apoyo inestable.
Mantenga una postura firme y un buen equilibrio en
todo momento.
• La zona de limpieza debe tener inclinaciones
adecuadas y sistema de drenaje para reducir la
posibilidad de caída debido a superficies resbaladizas.
• Sea extremadamente cuidadoso si debe usar la
hidrolavadora eléctrica desde una escalera, un
andamio u otro lugar similar.
• Sujete firmemente la pistola de pulverización con
ambas manos al utilizar modos de pulverización
eléctrica para evitar lesiones en caso de contragolpe de
la pistola.
ADVERTENCIA El chorro de agua a alta presión que
este equipo produce podría atravesar la piel y
los tejidos subcutáneos, y provocar lesiones
graves y posible amputación.
La pistola de pulverización acumula agua a alta
presión, incluso con el motor detenido y el agua
desconectada, lo que puede provocar lesiones graves.
• NUNCA apunte la pistola de pulverización hacia
personas, animales o plantas.
• SIEMPRE apunte con la pistola de pulverización hacia
una dirección segura y apriete el gatillo de la pistola
para liberar la alta presión, cada vez que apague la
hidrolavadora.
ADVERTENCIA Riesgo de lesiones oculares o
corporales. La pulverización podría
salpicar, propulsar objetos o causar
daños internos, lo que puede provocar
lesiones graves.
• Siempre use gafas de seguridad con ventilación indirecta
(salpicaduras de productos químicos) identificadas en
cumplimiento de la norma ANSI Z87.1 cuando utilice
este equipo o esté cerca de él. NUNCA sustituya las
gafas de seguridad con ventilación indirecta con gafas de
seguridad o gafas de condición seca.
• Sepa cómo detener la hidrolavadora y descargar la
presión rápidamente. Familiarícese completamente con
los controles.
• NO permita que ningún NIÑO opere la hidrolavadora
eléctrica.
• Mantenga el área de operación libre de personas.
• Inspeccione la manguera de alta presión antes de
cada uso. NUNCA repare la manguera de alta presión;
reemplácela.
• NO repare las conexiones con fugas con sellador de
ningún tipo; reemplace las juntas tóricas y juntas.
• Mantenga la manguera conectada a la hidrolavadora
eléctrica y a la pistola de pulverización cuando el
sistema esté presurizado.
• SIEMPRE apunte con la pistola de pulverización
hacia una dirección segura mientras el sistema esté
presurizado y apriete el gatillo de la pistola para liberar
la alta presión, cada vez que apague la hidrolavadora.
• NO apunte la pistola de pulverización hacia personas o
animales.
• NO beba de los accesorios conectados a la manguera.
• NO fije la pistola de pulverización en la posición abierta.
• NO deje la pistola de pulverización desatendida
cuando la hidrolavadora eléctrica está en la posición de
encendido (I).
• NO utilice una pistola de pulverización que no tenga
un bloqueo o seguro de gatillo instalado y en buenas
condiciones.
• Asegúrese siempre de que la pistola de pulverización y
los accesorios estén conectados correctamente.
• Manténgase alerta, observe lo que está haciendo.
• NO haga funcionar el producto si está cansado o bajo
la influencia de alcohol o drogas.
• Se requiere supervisión minuciosa cuando este
producto se utiliza cerca de niños.
ADVERTENCIA Riesgo de electrocución. El uso
de un cable de prolongación podría ocasionar
descarga eléctrica o quemaduras que pueden
provocar lesiones graves o la muerte.
• NO use un cable de prolongación con esta
hidrolavadora eléctrica. Es posible que el cable de
prolongación o el enchufe del circuito eléctrico de su
casa no proporcione la protección del interruptor de
circuito por fallos con conexión a tierra que resguarda
la vida de las personas.
ADVERTENCIA Riesgo de electrocución. Poner en
contacto al mismo tiempo ambos conductores
de energía podría provocar una descarga
eléctrica o incendio que causen muertes o
lesiones graves.
• Conectarla solo a un toma corriente con una buena
descarga a tierra. NO quite el terminal de tierra del enchufe.
• Compruebe que el cable esté en buenas condiciones antes
de usar la unidad. NO la utilice si el cable está dañado.
• El producto cuenta con un interruptor del circuito de fallo a
tierra (GFCI) que se encuentra en el cable del enchufe. Si es
necesario reemplazar el enchufe o el cable, reemplácelos
exclusivamente por piezas de repuesto idénticas.
• Mantenga todas las conexiones secas y lejos del suelo.
• NO toque el enchufe con las manos mojadas.
• NO pase el cable por entradas, ventanas, orificios en
los techos, paredes o pisos.
• NO pise el cable.
• NO aplaste, arrastre o coloque objetos sobre el cable.
• NO moje el área cercana a la fuente de energía.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Simplicity 020667-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Simplicity 020667-00 User manual
- español: Simplicity 020667-00 Manual de usuario