Antari F-1 Fazer Manuel utilisateur

1

F-1 Fazer

User Manual

Engli sh Français Deutsch • • • 中文

3

User Manual - English

Safety Information

Please read the following safety information carefully before operating the

machine. This information includes important safeguards about installation,

usage, and maintenance. Pay attention to all warning labels and instructions in

this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

․ Keep this device dry.

․ Always connect to a grounded circuit to avoid risk of electrocution.

․ Before connecting the machine to power, always check the voltage indicated on

the machine matches your local AC voltage. Do not use the machine if the AC

power voltage does not match.

․ Disconnect the machine from AC power before servicing and when not in use.

․ This product is for indoor use only! Do not expose to rain or moisture. If fluid is

spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto

electronic parts, immediately unplug the machine and contact your local Antari

dealer for advice.

․ No user serviceable and modifiable parts inside. Never try to repair this product,

an unauthorized technician may cause damage or malfunction to the machine.

․ For adult use only. Never leave the machine running unattended.

․ Installed the machine in a well-ventilated area. Provide at least 50 cm space

around the machine.

․ Never add flammable liquid of any kind to the machine.

․ Make sure there are no flammable materials close to the machine while operating.

4

․ Only use Antari fluid. Other fluid may lead to heater clog or malfunction.

․ If the machine fails to work, unplug the machine and stop operation immediately.

Contact your local Antari dealer for advice.

․ Before transporting the machine, make sure the fluid tank is completely drained.

․ Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it

securely. In case of eye contact or if fluid is swallowed, immediately seek medical

advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retain the

packing material for inspection.

What is included: 1 x F-1 Fazer

1 x Power Cord

1 x User Manual

Product Dimensions

275mm

608mm

286mm

5

Product Overview

Both Wireless Remote and Wireless DMX are Optional and not included

Optional Wireless Remote Add On Kit: WTR-10

Optional Wireless DMX Add On Kit: W-DMX-PCBR

Setting Up

Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm

of open space around the machine.

Step 2: Fill the fluid tank with Antari approved fluid.

Step 3: Connect the machine to a suitably rated power supply.To determine the power

requirement for the machine refer to the label on the back of the machine.

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Blue LCD screen, Timer

mode, Volume mode

Neutrik PowerCon

Breaker

XLR 3-Pin DMX Connector

Wireless Remote / WDMX

Wireless Solution

XLR 5-Pin DMX Connector

Power ON / OFF

6

Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 4 mintues.

Once the machine has reached operating temperature, the display will show Ready to

Faze. Now the machine is ready for operation.

Step 5: To start making haze, press the VOLUME button on the control panel.

Step 6: To turn off the machine, hold the STOP button for 3 seconds; the machine will

automatically run a self-cleaning process and shut off after the process is done.

Operation

Control Panel Operation

The machine can be operated with the onboard digital control interface.

Button

Function

[MENU]

Scroll through setting menu

[UP]/[TIMER]

Up/Activate Timer fucntion

[DOWN]/[VOLUME]

Down/Activate Volume function

[STOP]

Deactivate Timer/Volume function.

Or to select and memorize the setting.

Hold 3 seconds to start self-cleaning process and shut

down the machine

Control Menus

Both the Wireless Remote and W-DMX menu only function when the Optional Wireless

Remote or W-DMX Add On Kits are installed.

Antari F-1

Ready to Faze

7

Set interval time at Timer mode from 5 to 200 seconds

Set duration time at Timer mode from 1 to 200 seconds

Set output volume at Timer mode from 1 to 100 %

Set output volume at Volume mode from 1 to 100 %

Set fan speed from 20 to 100%

Set DMX/W-DMX address from 1 to 511

Turn On/Off Wireless Remote Control function

Turn On/Off Air Pump Sensor

Select DMX mode from 2ch, 1ch, and Sync mode

Turn On/Off W-DMX function

Unlink from a W-DMX transmitter

Interval Set

XXX Sec

Duration Set

XXX Sec

Timer Output

XXX %

Volume Output

XXX %

Fan Speed

XXX %

DMX-512

Address: XXX

W-DMX Power

XX

Wireless

XX

Air Pump Sensor

XX

DMX Mode

XXXX

W-DMX Reset

XXX

8

Turn On/Off run last setting function

Turn On/Off Keypad Sound

DMX Connector Pin Assignment

The machine provides a 3- or 5-pin XLR connector for DMX connection. The diagram below

indicates pin assignment information.

Function

1

Ground

2

Data-

3

Data+

4

N/A

5

N/A

DMX Operation

Making the DMX Connection – Connect the machine to a DMX controller or to one of the

machines in the DMX chain. The machine uses a 3-pin or 5-pin XLR connector for DMX

connection, the connector is located on the front of the machine.

Run Last Setting

XX

Keypad Sound

XX

9

Address Setup – Use control menu to set DMX address. The machine occupies 2 control

channels. The starting address is defined as the first channel from which the machine will

respond to the controller. Always double check to make sure there are no overlapping

channles in order to control the machine correctly.

DMX Channel Function

Channel Mode

Channel

Value

Function

2

1

0-4

Faze off

5-255

Faze 1-100%

2

0-4

Fan 20%

5-255

Fan 21-100%

1

0-4

Faze off

Fan 100%

5-255

Faze 1-100%

Fan 100%

Sync

1

0-4

Faze Off

Fan 20%

5-255

Faze 1-100%

Fan 21-100%

10

Status of W-DMX connection (Optional)

Symbol on the Liquid Crystal Display

Status of W-DMX connection

●

Transmitter assigned, DMX signal received

◎

Transmitter assigned, No DMX signal

⊙

Transmitter link lost or linking to transmitter

○

Transmitter not assigned

Wireless Remote Control Operation (Optional)

The optional wireless remote control system consists of a handheld transmitter and a

receiver on the rear of the machine.

*This menu function is only available when the Optional Wireless Remote Control Add On

Kit is installed:

Turn On/Off Wireless Remote Control function

Optional Wireless Remote Control Add On Kit: WTR-10

*Handheld Transmitter

With the transmitter, it is possible to make haze output via radio signal at maximum

distance of 50 meters. Press the button “A” to produce haze output and press the button “B”

to stop hazing.

Wireless

XX

11

*Receiver

If the optional wireless remote control function is selected and included, a radio signal

receiver is tested and pre-attached on the machine. The included transmitter also has been

paired with the attached receiver before shipping.

To activate or deactivate the wireless remote control function, press [Menu] button until the

LCD displays “Wireless”. Then press the ▲ [Up] or ▼ [Down] button to turn on and off the

wireless remote control function.

Registering transmitter

Transmitter can be paired from the receiver. Each receiver can pair up to 5 transmitters.

Follow below steps to pair transmitter from receiver.

Step 1: Turn on machine and turn on wireless remote control function.

Step 2: Power off machine and turn on again

Step 3: Wait until display show “Wireless Detecting”

Step 4: Press [A] button on the transmitter to pair

Note:

Multiple transmitter can be registered at once. When registering new transmitters, previous

registered transmitters will be automatically deleted.

Antari F-1

Ready to Faze

12

Installation instructions for wireless remote antenna

Step 1: unscrew and remove the flat cover on the machine.

Step 2: Pull out the cable with terminal.

13

Step 3: Connect the terminal to W-1 Wireless Signal Receiver.

Step 4: Screw the receiver on machine tightly.

The installation is completed.

Notes:

1. Once the wireless remote control function is turned On, the letter “W” will be displayed

on the LCD screen.

2. Once the wireless remote control function is turned On, the LCD screen will display

“Wireless Detect …” each time when the machine is turned on; this allows users to pair

new transmitter with the machine’s receiver. Every new registration overwrites the

14

previous memory.

3. One machine can be controlled by up to 5 transmitters while one transmiter can be

registered to an unlimited number of machines.

W-DMX Control Operation (Optional)

* The optional wireless DMX control system consists of a W-DMX PCB inside the machine

and a W-DMX antenna on the rear of the machine.

Optional Wireless DMX Add On Kit: W-DMX-PCBR

These menu functions are only available when the Optional Wireless DMX Control Add On

Kit is installed:

Turn On/Off W-DMX function

Unlink from a W-DMX transmitter

* How to install W-DMX board and antenna onto F-1

W-DMX Power

XX

W-DMX Reset

XXX

15

Step 1. Remove the screws on the top of F-1.

Step 2. Remove the screws on the side of F-1.

Step 3. Remove the cover on the control panel.

Step 4. Put the antenna (Part # W-

DMXR) onto F-1

16

Service and Maintenance

․ Do not allow the machine and fluid to become contaminated.

․ Regularly fill distilled water to fluid tank and run the machine to clean the system.

After cleaning, refill Antari fog fluids into fluid tank and make sure the machine can

produce fog properly.

․ It is recommended to run the machine on a monthly basis in order to achieve best

Step. 6

The red-framed area is where the W-DMX

board is placed.

Step 7. Install the W-DMX onto the main PCB and

then screw the screw tightly. The installation of W-

DMX antenna and W-DMX board is completed.

Step 5.

Connect the antenna (Part #

W-DMXR onto the W-DMX

board (Part # W-DMX-PCB)

The Part Number of Optional Wireless DMX

module is W-DMX-PCBR (1 x W-DMX antenna + 1 x

W-DMX board)

17

performance and output condition.

․ Excessive dust, liquid and dirt built up will degrade performance and cause

overheating.

Technical Specifications

- Input voltage

- Rated power

- Warm-up time

- Fluid consumption

- Fluid tank capacity

- Compatible fluid

- Operating time

- Ambient temp. range

- Output

- Control

- DMX channels

- Connection

- Optional accessories

- Dimension

- Weight

US model : AC 100-120V, 50 / 60Hz 6.8A

EU model : AC 220-240V, 50 / 60Hz 3.5A

760W

4.5 minutes (approx.)

8.5 ml/min

2.4l (0.63gal)

Antari FLG Heavy Fog Fluid

4.5 hrs at max. output

0 °C - 40 °C (32 °F-104 °F)

6200 ft

3

/min (176 m

3

/min)

DMX512, Timer, Manual,

Wireless (Optional)

Wireless DMX (Optional)

2 channels

Neutrik Powercon (Power)

XLR 3-pin and 5-pin (DMX)

W-DMX-PCBR Wireless DMX

WTR-10 Wireless Remote Set

WTR-40 Wireless DMX and W-1 Transmitter

L618 W275 H327 mm

(L24.33 W10.83 H12.87 inch)

14.1 kg (31.09 lbs)

18

Mode d'emploi - Franç ais

Notices de Sécurité

En vue d'utiliser correctement votre nouvel appareil, veuillez lire attentivement

ce mode d'emploi. Pour assurer la longévité et le bon fonctionnement de votre

machine à fumée, veuillez lire attentivement les instructions suivantes

concernant le maniement, la sécurité et l'entretien. Veuillez suivre toute

instruction de sécurité appliquée sur le boîtier de votre générateur à fumée

Antari.

Si vous avez des questions sur l'usage de la machine en toute sécurité, contactez votre

revendeur Antari.

․ Protéger de l'humidité.

․ Utilisez uniquement des prises de courant à terre à 3 broches.

․ Avant la première mise en marche, assurez-vous que l'appareil soit branché à

l'alimentation correcte. Ne jamais utiliser la machine quand la voltage n'est pas

correcte.

․ Débranchez l'appareil du secteur avant d'entretien ou quand vous n'utilisez pas la

machine.

․ L'appareil a été conçu pour un emploi dans des locaux clos. Protéger de

l'humidité. En cas de projection de liquide, débranchez l'appareil du secteur et

nettoyez avec un chiffon humide. Si du liquide devait pénétrer à l’intérieur de

l’appareil, débranchez le immédiatement et contactez un technicien ou votre

revendeur Antari avant de le réutiliser.

․ A l'intérieur de l'appareil, il n'y a aucune partie qui ait besoin d'être révisée. Ne

jamais essayer de repairer le produit parce quet détruire la machine.

․ L'usage de cet appareil n'est prévu que pour les adultes. Ne jamais faire marcher

19

sans surveillance.

․ Installez l'appareil à un endroit bien aéré. Pour garantir une aération suffisante,

laissez un espace libre de 50 cm tout autour de l’appareil.

․ Ne jamais mélanger des liquides inflammables gazeux ou huileux avec le liquide à

fumée.

․ Respectez une distance minimum de 50 cm entre le bec de la machine et les

matériaux inflammables.

․ Employez uniquement des liquides à fumée de haute qualité à base d'eau Antari

FLP ou liquides recommandée par votre revendeur. D'autres liquides à fumée

pourraient causer des problèmes d'encrassement ou des crachotements.

․ Si votre machine à fumée Antari ne devait plus fonctionner correctement, éteignez

le immédiatement. S'il vous plaît contactez votre revendeur Antari.

․ Faites attention à ce que le réservoir soit toujours complètement vidé avant

d’envoyer ou transporter l’appareil.

․ Ne jamais avaler le liquide à fumée. Stocker avec prudence. Si c’était tout de

même le cas, consultez un médecin immédiatement.

Déballage & Inspection

Ouvrez le carton extérieur et assurez vous que toutes les pièces n'aient subi aucun

dommage durant leur transport. En cas de livraison endommagée ou incomplète, toujours

contactez immédiatement votre revendeur Antari.

Dans votre carton : 1 x F-1 Fazer

1 x Câble d'alimentation

1 x Mode d'Emploi

20

Dimensions du Produit

Descriptif du Produit

La télécommande et le W-DMX sont accessoires vendus séparément.

En option : kit d'extension télécommande sans fil WTR-10

En option : kit d'extension W-DMX W-DMX-PCBR

275mm

608mm

286mm

Écran LCD bleu, mode

timer, mode volume

Neutrik PowerCon

Disjoncteur

Connecteur DMX XLR 3 broches

Télécommande sans fil / module

WDMX Wireless Solution

Connecteur DMX XLR 5 broches

Commutateur d’alimentation

La page charge ...

Antari F-1 Fazer Manuel utilisateur

Ce manuel convient également à

Antari F-1 Fazer Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents