Eaton EGS100L24R Manuel utilisateur

IB70-8671 For more information visit: www.eaton.com

O & M Manual for the EGS Automatic

Transfer Switch with RTC-50 Control

and Integral Loadcenter - 100 Amp

Instructional Booklet

New Information

Description Page

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. Receiving, Handling, and Storage . . . . . . . . . . . . . . . . 5

3. Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . 5

4. Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . 7

5. Functional Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6. Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7. Maintenance and Component Replacement. . . . . . . . . . 13

For more information visit: www.eaton.com IB70-8671

Instructional Booklet

Page 2 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

.

Figure 1. Typical Automatic Transfer Switch Equipment

Nameplate.

All possible contingencies that may arise during installation, opera-

tion, or maintenance, and all details and variations of this equip-

ment do not purport to be covered by these instructions. If

further information is required by the purchaser regarding a partic-

ular installation, application, or maintenance activity, please con-

tact an authorized Eaton sales representative or the installing

contractor.

SECTION 1: INTRODUCTION

1.1 Preliminary Comments and Safety Precautions

This technical document is intended to cover most aspects associ-

ated with the installation, application, operation, and maintenance

of the Automatic Transfer Switch (ATS). It is provided as a guide

for authorized and qualified personnel only. Please refer to the

specific WARNING and CAUTION in Section 1.1.2 before proceed-

ing. If further information is required by the purchaser regarding a

particular installation, application, or maintenance activity, please

contact an authorized Eaton sales representative or the installing

contractor.

1.1.1 Warranty and Liability Information

No warranties, expressed or implied, including warranties of fit-

ness for a particular purpose of merchantability, or warranties aris-

ing from course of dealing or usage of trade, are made regarding

the information, recommendations, and descriptions contained

herein. In no event will Eaton be responsible to the purchaser or

user in contract, in tort (including negligence), strict liability, or

otherwise for any special, indirect, incidental or consequential

damage, or loss whatsoever, including but not limited to damage

or loss of use of equipment, plant or power system, cost of capi-

tal, loss of power, additional expenses in the use of existing

power facilities, or claims against the purchaser or user by its cus-

tomers resulting from the use of the information and descriptions

contained herein.

1.1.2 Safety Precautions

All safety codes, standards, and/or regulations must be strictly

observed in the installation, application, operation, and mainte-

nance of this device.

WARNING

READ AND UNDERSTAND THE INSTRUCTIONS CONTAINED HEREIN-

AFTER BEFORE ATTEMPTING TO UNPACK, ASSEMBLE, OPERATE,

OR MAINTAIN THIS EQUIPMENT.

HAZARDOUS VOLTAGES ARE PRESENT INSIDE TRANSFER SWITCH

ENCLOSURES THAT CAN CAUSE DEATH OR SEVERE PERSONAL

INJURY. FOLLOW PROPER INSTALLATION, OPERATION, AND MAIN-

TENANCE PROCEDURES TO AVOID THESE VOLTAGES.

THE TRANSFER SWITCH EQUIPMENT COVERED BY THIS INSTRUC-

TION BOOK IS DESIGNED AND TESTED TO OPERATE WITHIN ITS

NAMEPLATE RATINGS. OPERATION OUTSIDE OF THESE RATINGS

MAY CAUSE THE EQUIPMENT TO FAIL RESULTING IN DEATH, SERI-

OUS BODILY INJURY, AND/OR PROPERTY DAMAGE. ALL RESPON-

SIBLE PERSONNEL SHOULD LOCATE THE DOOR MOUNTED

EQUIPMENT NAMEPLATE AND BE FAMILIAR WITH THE INFORMA-

TION PROVIDED ON THE NAMEPLATE. A TYPICAL EQUIPMENT

NAMEPLATE IS SHOWN IN FIGURE 1.

L050412234

Cat No: EGS100L24R ENCL TYPE: 3R

Style No: ITEM: 001

GO No: ABC0123 PIECE: 001

OF: 001

Volts: 240 Amps: 100 Hertz: 60

Poles: 2 Phase: 1 Wire: 3

30-43465

WARNING

THE WARNINGS AND CAUTIONS INCLUDED AS PART OF THE PRO-

CEDURAL STEPS IN THIS DOCUMENT ARE FOR PERSONAL SAFETY

AND PROTECTION OF EQUIPMENT FROM DAMAGE. AN EXAMPLE

OF A TYPICAL WARNING LABEL HEADING IS SHOWN ABOVE TO

FAMILIARIZE PERSONNEL WITH THE STYLE OF PRESENTATION.

THIS WILL HELP TO ENSURE THAT PERSONNEL ARE ALERT TO

WARNINGS, WHICH APPEAR THROUGHOUT THE DOCUMENT. IN

ADDITION, CAUTIONS ARE ALL UPPER CASE AND BOLDFACE.

CAUTION

READ AND UNDERSTAND THE MATERIAL PRESENTED IN THIS DOC-

UMENT BEFORE ATTEMPTING INSTALLATION, APPLICATION, OPER-

ATION, OR MAINTENANCE OF THE EQUIPMENT. IN ADDITION,

ONLY QUALIFIED PERSONS SHOULD BE PERMITTED TO PERFORM

ANY WORK ASSOCIATED WITH THE EQUIPMENT. ANY WIRING

INSTRUCTIONS PRESENTED IN THIS DOCUMENT MUST BE FOL-

LOWED PRECISELY. FAILURE TO DO SO COULD CAUSE PERMA-

NENT EQUIPMENT DAMAGE.

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 3

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

1.2 General Information

ATSs are used to protect critical electrical loads against loss of

power. The load’s utility power source is backed up by a genera-

tor power source. An ATS is connected to both the utility and

generator power sources and supplies the load with power from

one of these two sources. In the event that power is lost from the

utility power source, the ATS transfers the load to the generator

power source. Once the utility power is restored, the load is auto-

matically transferred back to the utility power source (Figure 2).

Figure 2. Typical Load Transfer Switch (Contactor) Schematic.

An intelligence system initiates the transfer when the utility power

source fails or falls below a preset voltage. An engine start is

then initiated by the generator and the ATS transfers to the gener-

ator power source when sufficient generator voltage is available.

When the utility power source is restored, the ATS automatically

transfers back and the generator will shut down after a time delay.

In the event the utility power source fails and the generator

power source does not appear, the ATS remains connected to the

utility power source until the generator power source does appear.

Conversely, if connected to the generator power source and the

generator power source fails while the utility power source is still

unavailable, the ATS remains connected to the generator power

source.

ATSs automatically perform the transfer function, and include

three basic elements.

1. Main contacts to connect and disconnect the load to and from

the source of power.

2. Solenoids to make the transfer of the main contacts from

source to source.

3. Intelligence/supervisory circuits to constantly monitor the con-

dition of the power sources and thus provide the intelligence

necessary for the switch and related circuit operation.

1.2.1 Design Configuration

The Eaton Residential ATS is a rugged, compact design that uti-

lizes power contactors to transfer essential loads from one power

source to another (see Figure 3). The Residential ATS contains

suitable mechanical and/or electrical interlock switches to elimi-

nate the possibility of connecting the utility service to the genera-

tor output. In addition, a manual override lever is provided for the

transfer function.

Figure 3. EGS100L24R (100 A).

1.2.2 Load Shed Contacts

Two sets of contacts are available and can be used to control

large connected loads on the generator (i.e. air conditioners, hot

tubs, etc.). The contacts are rated for 250 Vac, 5 amps maxi-

mum.

1.3 Transfer Switch Catalog Number Identification

ATS equipment catalog numbers provide a significant amount of

relevant information pertaining to a specific piece of equipment.

The Catalog Number Identification Table (see Table 1) provides

the required interpretation information.

Utility

Generator

Load

WARNING

DO NOT MANUALLY TRANSFER THE SWITCH WHILE UNDER LOAD.

For more information visit: www.eaton.com IB70-8671

Instructional Booklet

Page 4 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

Table 1. ATS Catalog Numbering System

1.4 Environmental and Operational Conditions

Normally, an ATS is applied indoors in an electrical equipment

room. It can also be used for normal outdoor applications (with

standard NEMA 3R enclosure) where the equipment is subject to

falling rain, freezing temperatures, and 95% humidity (non-con-

densing). The ambient temperature range for operation is

between -20 and 70°C (-4 and 158°F).

1.5 Glossary

With respect to their use within this document and as they relate

to transfer switch and controller operation, the following terminol-

ogy is defined.

Available

A source is defined as “available” when it is within its undervolt-

age setpoint ranges for the nominal voltage setting.

Connected

Connected is defined as when the input is shorted by an external

contact or connection.

Failed or Fails

A source is defined as “failed” when it is outside of the applicable

voltage setpoint ranges for the nominal voltage and for a time

exceeding 0.5 seconds after the time delay emergency fail (TDEF)

time delays expires.

Failsafe

Failsafe is a feature that prevents disconnection from the only

available power source and also forces a transfer or re-transfer

operation to the only available power source.

Re-Transfer

Re-transfer is defined as a change of the load connection from the

Generator to the Utility.

Utility

Utility is the primary source (normal source, normal power source,

or normal).

Generator

Generator is the secondary source (generator emergency source,

emergency power source, emergency, standby, or backup

source).

Utility: Failed or Fails

Utility is defined as “failed” when it is outside of its undervoltage

setpoint ranges for the nominal voltage and frequency setting.

Generator: Failed or Fails

Generator is defined as “failed” when it is outside of its undervolt-

age/underfrequency/overfrequency (if applicable) setpoint ranges

for the nominal voltage and frequency setting for a time exceeding

0.5 seconds after the Time Delay Emergency Fail (TDEF) time

delay expires.

Transfer

Transfer is defined as a change of the load connection from the

Utility to the Generator power source.

Unconnected

Unconnected is defined as when the input is not shorted by an

external contact or connection.

100

100 = 100 A

Loadcenter

L24 - 24 Circuit

L 24

R

Enclosure Type

R = Type 3R

Eaton

Generator

Switch

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 5

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

SECTION 2: RECEIVING, HANDLING, AND

STORAGE

2.1 Receiving

Every effort is made to ensure that the ATS equipment arrives at

its destination undamaged and ready for installation. The packing

is designed to protect the internal components as well as the

enclosure. Care should be exercised, however, to protect the

equipment from impact at all times. Do not remove the protective

packaging until the equipment is at the installation site and ready

to be installed.

When the ATS equipment reaches its destination, the customer

should inspect the shipping container for any obvious signs of

rough handling and/or external damage that occurred during trans-

portation. Record any external and internal damage for reporting

to the transportation carrier and to the Eaton sales representative,

once a thorough inspection is complete. All claims should be as

specific as possible and include the Shop Order and General Order

numbers.

A shipping label affixed to the shipping container includes a vari-

ety of equipment and customer information, such as General

Order and catalog numbers. Make certain that this information

matches the other shipping paper information.

Each ATS enclosure is packaged in its own box. Do not discard

the packing material until the equipment is ready for installation.

Once the packaging is removed from the shipment, the enclosure

door can be opened. A plastic bag of documents will be found in

the enclosure. Important documents, such as wiring diagrams and

appropriate instruction leaflets are enclosed within the bag and

should be filed in a safe place.

2.2 Handling

As previously mentioned, ATS equipment is packaged in its own

box. Protect the equipment from impact at all times and do not

double stack. Once the equipment is at the installation site and

ready to be installed, the packaging material can be removed.

Refer to Section 4 of this manual for specific installation instruc-

tions.

2.3 Storage

Although well packaged, this equipment is not suitable for outdoor

storage. The equipment warranty will not be applicable if there is

evidence of outdoor storage. If the equipment is to be stored

indoors for any period of time, it should be stored with its protec-

tive packaging material in place. Protect the equipment at all

times from excessive moisture, construction dirt, corrosive condi-

tions, and other contaminants. It is strongly suggested that the

package-protected equipment be stored in a climate-controlled

environment of -20 to 70°C (-4 to 158°F), with a relative humid-

ity of 80% or less. Do not, under any circumstance, stack other

equipment on top of an ATS equipment enclosure, whether pack-

aged or not.

SECTION 3: EQUIPMENT DESCRIPTION

3.1 Introduction

The Eaton Residential ATS is assembled and tested at the factory.

It is designed to be used in conjunction with standby power distri-

bution equipment to provide an alternate source of power to criti-

cal circuits in the event that the primary power source is

interrupted.

This ATS monitors both utility and generator power sources and

automatically transfers critical load circuits between the two

sources, depending on which source is available. The utility

power source is preferred and will remain connected to the switch

if it is available.

3.2 Power Panel

The power panel is used for making load, power, and neutral con-

nections. The power contactor is mounted on a steel baseplate

(Figure 4).

Figure 4. Typical Power Panel for 100 A.

3.2.1 Main Contacts

This ATS incorporates power contactors as the main switching

device. The main contacts connect and disconnect the load to and

from the different power sources. The power contactor is

mechanically interlocked to prevent the two sets of main contacts

from being closed simultaneously.

For more information visit: www.eaton.com IB70-8671

Instructional Booklet

Page 6 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

3.3 RTC-50 Logic Panel

The RTC-50 is a microprocessor-based transfer switch logic con-

trol package. The hardware and software of the controller contain

the intelligence/supervisory circuits that constantly monitor the

condition of the power sources. It provides the intelligence neces-

sary for the operation of the ATS (Figure 5).

Figure 5. RTC-50 Logic Control Panel.

The RTC-50 controller has an operating temperature of

-20 to 70°C (-4 to 158°F).

The controller circuit board is protected by an insulating conformal

coating.

The specifications, under normal operating conditions, are as fol-

lows:

• Tolerance for voltage sensing function: ±1% of full scale

3.4 EGS ATS Features

A variety of standard and optional features are available for Eaton

ATSs. All features or combinations of features may not be avail-

able on specific ATSs. All features and/or accessories are Under-

writers Laboratories (UL) listed unless noted.

3.4.1 Standard Features

The following is a list of the standard features for the RTC-50

Controlled ATS.

1. Time Delay Normal to Emergency (TDNE)

This feature provides a time delay when transferring from the

Utility to the Generator power source. Timing begins when

the Generator becomes available. It permits controlled trans-

fer of the load circuit to the Generator.

Jumper selectable at 20 seconds or 50 seconds. Default is

20 seconds.

3. Time Delay Emergency to Normal (TDEN)

This feature provides a time delay of the re-transfer opera-

tion to permit stabilization of Utility. Timing begins when the

Utility becomes available. If the Generator fails during tim-

ing, then re-transfer is delayed for up to 6 seconds to allow

the generator to recover.

Fixed at 10 Seconds.

5. Generator Monitoring and Protection

This feature provides monitoring and protection based on the

Generator voltage setpoints. All feature functions are Fail-

safe operations.

5J. All Phase Undervoltage Protection

Undervoltage:

Dropout: 70% of nominal

Pickup: 80% of nominal

12. Power Source Annunciation

This feature provides LEDs to give power source availability

indications.

Switch Position

Provides LEDs to indicate the switch position

Power Source Availability

Provides LEDs to indicate if a power source is available.

LEDs may be integral or separate from the controller.

12G. Utility - Available

This feature provides a green LED that, when lit, indicates

the Utility is available.

12H. Generator - Available

This feature provides an red LED that, when lit, indicates

the generator is available.

15M. Load Shed

Two sets of contacts are available and can be used to con-

trol large connected loads on the generator (i.e. air condi-

tioners, hot tubs, etc.). The contacts are rated for 250 Vac,

5 amps.

26. Utility - Monitoring and Protection

This feature provides Utility monitoring and protection func-

tions. If the Utility power supply fails, then the RTC-50 will

begin the sequence of operations necessary to transfer the

load circuit to the Generator power supply. All Feature 26

monitoring and protection functions are Failsafe operations.

26P. All Phase Undervoltage Protection

Undervoltage:

Dropout: 70% of nominal

Pickup: 80% of nominal

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 7

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

3.5 Standards

Eaton ATS equipment is listed for application by UL. In addition,

Eaton ATSs are listed in File E316586 by Underwriters Laborato-

ries, Inc. under Standard UL 1008 and UL 67. This standard cov-

ers the requirements for ATSs intended for use in ordinary

locations to provide lighting and power as follows:

a. In standby systems, in accordance with article 702 of the

National Electrical Code.

Eaton ATSs are available to meet NFPA 110 for standby power

systems.

Eaton ATS equipment are listed for application by CSA. In addi-

tion, Eaton ATSs are listed in the Legacy File LR96245 Master

Contract 163545 by Canadian Standards Association under Stan-

dard 22.2 #178-1978

SECTION 4: INSTALLATION AND WIRING

4.1 General

Eaton ATSs are factory wired and tested. Installation requires sol-

idly mounting the enclosed unit and connecting the power cables

and the auxiliary sensing circuits. Physical mounting procedures

and power cable connections are covered in this section.

Once a transfer switch is properly installed and wired, it should be

mechanically and electrically checked for proper installation and

operation. The procedures for these initial mechanical and electri-

cal checks are outlined in Section 5 of this manual.

4.2 Mounting Location

Choose a location that offers a flat, rigid mounting surface capa-

ble of supporting the weight of the enclosed ATS equipment (see

Figure 6). Protect the transfer switch at all times against exces-

sive moisture, dust, dirt, lint, and corrosive vapors.

Figure 6. Dimensions and Plan View of a Standard EGS (in.) (100 A) Type 3R Enclosure.

WARNING

BE CERTAIN THAT THE DEADFRONT IS PROPERLY INSTALLED

BEFORE THE TRANSFER SWITCH EQUIPMENT IS PUT INTO SER-

VICE. THE DEADFRONT PROVIDES PROTECTION FROM DANGER-

OUS VOLTAGES AT THE LINE AND LOAD TERMINALS WHEN THE

EQUIPMENT IS IN OPERATION. FAILURE TO DO SO COULD RESULT

IN PERSONAL INJURY OR DEATH.

14.462

5.321

7.154

2.633

19.005

5.198

3.154

2.496

8.000

14.462

14.308

5.321

29.332

Instructional Booklet

Page 8 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

For more information visit: www.eaton.com IB70-8671

Check to ensure there are no pipes, wires, or other mounting haz-

ards in the immediate mounting area that could create a problem.

Carefully remove all packing material from the ATS enclosure at

the installation site. Even though an equipment inspection was

performed when the equipment was received, make another care-

ful inspection of the enclosure and the ATS mechanism as the

packing material is removed and the enclosure readied for mount-

ing. Be especially alert for distorted metal, loose wires, or dam-

aged components.

4.3 Mounting Procedure

With the enclosed ATS equipment unpacked and ready for mount-

ing, proceed with the following steps.

For Type 3R:

Step 1: Depress the padlockable catch at the bottom of the door

and slide the door downward (see Figure 7). Open the

door and remove the deadfront.

Figure 7. Location of the Door Latch.

Step 2: Utilize the 5-point hanging system to mount..

Step 3: Mount the switch to a rigid structure as close to the elec-

trical loads as possible.

4.4 Power Cable Connection

Test all power cables prior to connection to the unit to ensure that

the conductors or cable insulation has not been damaged while

being pulled into position.

Power cables are to be connected to solderless, screw type lugs

located on the automatic transfer switching devices. Verify that

the lugs supplied will accommodate the power cables being used.

Also verify that the cables comply with all local electrical codes.

Standard ATS equipment, as supplied from the factory, will

accommodate the wire sizes shown in Table 2.

Table 2. Wire Sizes for ATSs.

Carefully strip the insulation from the power cables to avoid nick-

ing or ringing of the conductor strands. Prepare the stripped con-

ductor termination end by cleaning it with a wire brush. If

aluminum conductors are used, apply an appropriate joint com-

pound to the clean conductor surface area.

Note:Tighten the cable lugs to the torque identified on the label affixed to

the unit.

Step 1: Connect cables as follows (see Figure 8 and Table 2):

• The utility power cables to the utility lugs;

• The generator power cables to the generator lugs;

• The customer load cables to the distribution panel;

• The neutral cables to the neutral bar; and

• The ground wires to the ground bar.

CAUTION

EXTREME CARE SHOULD BE TAKEN TO PROTECT THE ATS FROM

DRILL CHIPS, FILINGS, AND OTHER CONTAMINANTS WHEN MAK-

ING THE CABLE ENTRY HOLES AND MOUNTING THE ENCLOSURE

TO PREVENT COMPONENT DAMAGE OR A FUTURE MALFUNCTION.

NOTICE

THE INSTALLATION MUST FULLY COMPLY WITH ALL APPLICABLE

CODES, STANDARDS, AND REGULATIONS.

NOTICE

FOR CONTROL WIRING (GENERATOR ENGINE START WIRING), THE

WIRES MUST BE ISOLATED FROM BOTH THE UTILITY AND GENERA-

TOR POWER SOURCE CABLES.

WARNING

POWER CONDUCTORS MAY HAVE VOLTAGE PRESENT THAT CAN

CAUSE SEVERE PERSONAL INJURY OR DEATH. DE-ENERGIZE ALL

POWER OR CONTROL CIRCUIT CONDUCTORS TO BE CONNECTED

TO THE ATS EQUIPMENT BEFORE BEGINNING TO WORK WITH THE

CONDUCTORS AND/OR TERMINATING THEM TO THE EQUIPMENT

CAUTION

TO HELP PREVENT COMPONENT DAMAGE OR FUTURE MALFUNC-

TIONS, USE EXTREME CARE TO KEEP CONTAMINANTS OUT OF

THE ATS EQUIPMENT WHEN MAKING THE POWER CABLE CONNEC-

TIONS.

TRANSFER SWITCH

AMP RATING

CONTACTOR WIRE

SIZE RANGE

NUMBER OF CABLES

PER PHASE

100 #14 –2/0 1

CAUTION

IMPROPER POWER CABLE CONNECTIONS CAN CAUSE EXCESSIVE

HEAT AND SUBSEQUENT EQUIPMENT FAILURE.

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 9

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

.

Figure 8. Cable Connection Locations (100 A).

Step 2: The generator utility sensing connections are located on

the fuse block that is installed at the bottom of the power

panel. The utility sensing wires, required for proper gener-

ator operation, are connected at this point. See Section

4.7 for more detailed information on connecting the gen-

erator utility sensing wires.

Figure 9. Generator Utility Sensing Wires Connection.

Step 3: Tighten all cables and wiring to specifications.

GEN LUGS

UTILITY

LUGS

GENERATOR

LOAD LUGS

UTILITY LUGS

LUGS

UTILITY SENSING WIRE CONNECTION

UTILITY

LUGS

LOAD

LUGS

GENERATOR

LUGS

GROUND

NEUTRAL

For more information visit: www.eaton.com IB70-8671

Instructional Booklet

Page 10 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

4.5 Wiring

4.6 Installation

In a typical installation for critical loads (see Figure 10), the ATS

(1) and the generator (2) are connected to the power supply. The

ATS and emergency distribution panel (1) receive utility power

from a dedicated breaker in the utility service panel (3). The ATS

and emergency panel receive generator power from the generator

(2). Power from the utility feeds the utility panel.

Figure 10. Typical Installation of a Residential ATS.

The ATS (1) and generator (2) are connected to the power supply.

The automatic transfer switch is located between the generator

and the utility panel (3).

When the utility power fails, the ATS will sense the failure, the

generator will start, and when sufficient generator voltage is avail-

able, the ATS will switch all loads to the emergency panel. All

emergency loads will receive power from the generator. A line

breaker is required between the generator power source and the

transfer switch (see Figure 11). When utility power returns, the

ATS will switch all power back to the utility panel and the genera-

tor will shut down.

Figure 11. Diagram of a Typical Installation (Critical Loads Only).

4.7 Generator Utility Sensing Connection

The generator utility sensing connections are located on the fuse

block that is installed at the bottom of the power panel. The utility

sensing wires, required for proper generator operation, are con-

nected at this point.

Note: Prior to making the generator utility sensing connection to the ATS,

set the generator control selector switch to the OFF position to prevent an

unwanted generator start. Control wiring, such as the generator utility

sensing wires, must be run separately from the power cables.

Use the proper wire size as listed by the generator set (Genset)

manufacturer.

This ATS is intended for use on generators with built in auto start

features. These generators sense, and react to, utility power.

Remote starting contacts are not provided in this transfer switch.

WARNING

POWER CONDUCTORS AND CONTROL WIRING MAY HAVE VOLT-

AGE PRESENT THAT CAN CAUSE SEVERE PERSONAL INJURY OR

DEATH. DE-ENERGIZE ALL POWER OR CONTROL CIRCUIT CONDUC-

TORS BEFORE BEGINNING TO PERFORM ANY WIRING ACTIVITY TO

OR WITHIN THE ATS EQUIPMENT.

CAUTION

CHECK THE ATS EQUIPMENT NAMEPLATE FOR RATED VOLTAGE.

IT SHOULD BE THE SAME AS THE UTILITY AND GENERATOR LINE

VOLTAGES. OPERATING THE EQUIPMENT ON IMPROPER VOLTAGE

CAN CAUSE EQUIPMENT DAMAGE.

Generator

(Source 2)

Circuit Breaker

(typically included

in Genset)

EDitibtiPl

Critical

Loads

Utility

(Source 1)

Watt-Hour

Meter

Non-Critical

Loads

Utility Panel

Transfer

Switch

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 11

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

4.8 Preliminary Checks

After the ATS enclosure is installed and power cables are con-

nected to the equipment, thoroughly inspect the unit to ensure

that no tools were left inside and that the cabinet is free of debris.

If necessary, use a vacuum cleaner to remove any and all con-

struction or installation debris from the equipment.

Read and understand all labels on the equipment. Review and

understand the wiring diagrams supplied with the equipment.

Note any optional accessories that may have been furnished with

this unit and review their operation.

Verify that the phase-to-phase line voltages of both the utility and

generator power sources are the same and that they match the

rated voltage as indicated on the ATS ratings label.

4.9 Protection

For Catalog # EGS100L24R only

When protected by one of the following circuit breakers rated not

more than 150 amperes, this transfer switch is rated for use on a

circuit capable of delivering not more than 25,000 RMS symmetri-

cal amperes, 240 volts maximum, but not more than the interrupt-

ing capacity of the selected circuit breaker.

Eaton/Cutler-Hammer

BR CH FDC CSR CSH

BW BWH

Siemens

CED6 ED6 ED4 HED6 HED4

When protected by circuit breakers without adjustable short-time

response only or by fuses this transfer switch is rated for use on a

curcuit capable of delivering not more than 10,000 RMS symmet-

rical amperes at 240V AC.

MANUFACTURER-ANY

BREAKER-ANY

TYPE-ANY

AMPS MAX-PER NEC

SECTION 5: FUNCTIONAL TESTING

5.1 Preliminary Checks

Step 1: Check all loads connected to the ATS to ensure that they

are ready to be energized.

5.2 Energize the Switch

Step 1: Close the upstream utility power source breaker or

switch to connect the ATS to the utility power source

voltage.

Step 2: Using a voltmeter, measure the line-to-line and the line-

to-neutral voltages across the utility line terminals to

ensure the utility voltage is correct.

Step 3: If the voltage is acceptable, the solenoid will engage and

the contactor will automatically switch to the UTILITY

position.

Step 4: Position the generator control selector switch, located on

the standby generator, to the AUTOSTART position. (It

may also be labeled REMOTE START or AUTO.)

5.3 Operational Checks

Step 1: Open the upstream utility breaker originally closed in

Step 1 of Section 5.2.

Step 2: After a time delay (based on the generator settings), the

standby generator engine will start.

Step 3: Using a voltmeter, measure the line-to-line and line-to-

neutral voltages across the generator line terminals to

ensure that the generator emergency voltage is correct.

If necessary, make adjustments to the voltage regulator

on the generator according to the manufacturer’s recom-

mendations to correct any voltage deviations. The ATS

will only respond to the correct voltage from the genera-

tor power source.

Step 4: Close the upstream generator power source breaker or

switch to connect the ATS to the generator power supply

source.

CAUTION

SEVERE EQUIPMENT DAMAGE CAN RESULT IF THE UNIT IS NOT

APPLIED AT PROPER VOLTAGE. DO NOT ENERGIZE THE EQUIP-

MENT IF THE SUPPLY VOLTAGES DO NOT MATCH EQUIPMENT

RATINGS LABEL.

WARNING

YOU ARE READY TO ENERGIZE THE EQUIPMENT. VOLTAGES

WITHIN THE ENCLOSURE ARE CAPABLE OF CAUSING SEVERE PER-

SONAL INJURY OR DEATH. USE EXTREME CAUTION TO AVOID

CONTACT WITH ENERGIZED EQUIPMENT.

WARNING

CONTACT WITH ENERGIZED COMPONENTS WILL CAUSE ELECTRI-

CAL SHOCK CAPABLE OF PRODUCING SEVERE PERSONAL INJURY

OR DEATH. USE EXTREME CAUTION TO AVOID CONTACT WITH

ENERGIZED COMPONENTS WHEN USING A METER FOR VOLTAGE

CHECKS.

NOTICE

THIS WILL SIMULATE AN INTERRUPTION OF THE UTILITY POWER

SOURCE.

For more information visit: www.eaton.com IB70-8671

Instructional Booklet

Page 12 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

Step 5: The ATS Time Delay Normal (Utility) to Emergency (Gen-

erator) (TDNE) will begin to time after the generator

engine begins to run. After time out, the solenoid will

engage and the contactor will automatically switch from

the UTILITY to the GENERATOR position.

Step 6: Close the utility breaker described in Step 1 of

Section 5.2.

Step 7: The ATS Time Delay Emergency (Generator) to Normal

(Utility) (TDEN) timer will begin timing, and the solenoid

will engage and automatically switch from the GENERA-

TOR to the UTILITY position and the generator will shut

down after a cool down period.

SECTION 6: ADJUSTMENTS

6.1 General

Refer to IB00405004E-70-8664, supplied with the ATS for

RTC-50 controller adjustments and functions.

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 13

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

SECTION 7: MAINTENANCE AND

COMPONENT REPLACEMENT

7.1 Introduction

In general, ATS equipment is designed to be relatively mainte-

nance free under normal usage. However, because of the variabil-

ity of application conditions and the importance placed on

dependable operation by this type of equipment, inspection and

maintenance checks should be made on a regularly scheduled

basis. Since equipment maintenance will consist mainly of keep-

ing the equipment clean, the frequency of maintenance will

depend, to a large extent, on the cleanliness of its surroundings.

If a significant amount of dust or foreign matter is present, a more

frequent maintenance schedule should be followed.

It is suggested that visual inspections of the equipment be made

on a regular basis, not just during regularly scheduled periods.

Always be alert for an accumulation of dirt in and around the

structure, loose parts and/or hardware, cracks and/or discolora-

tion to insulation, and damaged or discolored components.

Figure 12 is the wiring diagram for the EGS 100 Amp ATS switch.

Note:Only qualified and experienced personnel should attempt any diag-

nostic work using this diagram.

Figure 12. Wiring Diagram for the EGS100L24R ATS (Shown Deenergized).

WARNING

HIGH VOLTAGES ARE PRESENT IN AND AROUND TRANSFER

SWITCH EQUIPMENT. BEFORE INSPECTING OR MAINTAINING THIS

EQUIPMENT, DISCONNECT THE LINE POWER FROM THE EQUIP-

MENT BEING SERVICED BY OPENING AND LOCKING OUT, IF POSSI-

BLE, THE NEXT HIGHEST DISCONNECT DEVICE. FAILURE TO

FOLLOW THIS PROCEDURE COULD CAUSE SEVERE PERSONAL

INJURY AND/OR DEATH.

Instructional Booklet

Page 14 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

For more information visit: www.eaton.com IB70-8671

7.2 Procedures

A suggested maintenance procedure to be followed is outlined in Table 3.

Table 3. Recommended Periodic Maintenance Procedures.

STEP ACTION

a. Make the transfer switch equipment safe for inspection and/or maintenance. Disconnect the line power from the equipment being serviced by opening next highest disconnect

device. Make certain that any accessory control power is switched off.

b. Inspect the structure area for safety hazards or potential maintenance problems. Inspect the area, especially where the contactor is installed, for any safety hazards, including per-

sonal safety and fire hazards. Exposure to certain chemical vapors can cause deterioration of the

electrical connections.

Inspect for accumulated dirt, loose hardware, or physical damage.

Examine the primary insulation for evidence of cracking or overheating. Overheating will show as

discoloration, melting, or blistering of the conductor insulation, or as pitting or melting of the con-

ductor surfaces due to arcing.

Inspect the secondary control connections for damage, and control wiring for insulation integrity.

c. Inspect the contactor for dust, dirt, soot, grease, moisture, or corrosion. Remove dust, dirt, soot, grease, moisture, and corrosion contamination from the surface of the

switching device using a dry, soft lint-free cloth, dry soft bristle brush, and vacuum cleaner. Do

not blow debris into the contactor. If contamination is found, look for the source and fix the prob-

lem.

d. Check for material integrity, uneven wear, discoloration, or loose hardware. Severe material cracking will require replacement and loose hardware will need to be tightened.

e. Check the terminals and connectors for looseness or signs of overheating. Overheating will show as discoloration, melting, or blistering of the conductor insulation.

Connections that do not have signs of looseness or overheating should not be disturbed.

f. Exercise the contactor if it is not often exercised while in operation. This will permit the wiping

action by the contacts.

If a switching device is used for frequent switching during normal operation, this step can be disre-

garded.

g. Return the transfer switch equipment to service. Make certain all barriers are in place and the door is closed. Re-apply generator and utility power.

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 15

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

7.3 Maintenance Log

DATE ACTION

Example: 01/01/04 Inspected and cleaned.

Instructional Booklet

Page 16 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

For more information visit: www.eaton.com IB70-8671

7.4 Component Replacement

Certain components within the ATS are field replaceable. Table 4 lists the part numbers to use when ordering replacement components.

To order replacement components, contact an authorized Eaton sales representative.

Table 4. Field Replaceable Components.

7.4.1 Component Replacement Instructions

7.4.1.1 100 Ampere RTC-50 Controller

Figure 13. Controller Board Installed in a EGS ATS.

COMPONENT PART NUMBER ATS MODEL

Contactor 99-5638 100 A

RTC-50 Controller RTC50 100 A

Harness EGS 99-5638-3 100 A

Service Entrance Breaker 99-5638-4 100 A

Ground Bar 99-5638-15 100 A

Lugs 99-5638-6 100 A

Neutral Bar 99-5638-17 100 A

SurgTel DHW4PT 100 A

SurgCable DCXCAB2 100 A

TVSS 99-5638-10 100 A

WARNING

HIGH VOLTAGES ARE PRESENT IN AND AROUND TRANSFER

SWITCH EQUIPMENT. BEFORE ATTEMPTING TO REPLACE ANY

COMPONENT, DISCONNECT THE LINE POWER FROM THE EQUIP-

MENT BEING SERVICED BY OPENING AND LOCKING OUT, IF POSSI-

BLE, THE NEXT HIGHEST DISCONNECT DEVICE. FAILURE TO

FOLLOW THIS PROCEDURE COULD CAUSE SEVERE PERSONAL

INJURY AND/OR DEATH.

ALWAYS TURN THE UTILITY (SOURCE 1) POWER OFF AND TURN

THE GENERATOR (SOURCE 2) CONTROL SELECTOR SWITCH TO

THE “OFF” POSITION BEFORE ATTEMPTING TO REPLACE ANY COM-

PONENTS.

NOTICE

APPLY UTILITY (SOURCE 1) POWER AND PLACE THE GENERATOR

CONTROL SELECTOR SWITCH IN THE “AUTO” POSITION AFTER THE

COMPONENT HAS BEEN REPLACED. TEST THE SYSTEM FOR

PROPER FUNCTIONALITY.

RTC-50

Controller

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 17

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

Step 1:Turn the Generator Start select to “OFF” before attempt-

ing to replace the RTC-50 Controller. Ensure all sources of

power are removed.

Step 2: Disconnect the J1, J2, J3, J4, and J6 plugs from the con-

troller (see Figure 14).

Step 3: Disconnect the wires connected to J7 and J8.

Step 4: Remove the four (4) screws located at the corners of the

controller that secure it to the power panel. Remove the

controller (see Figure 14).

Figure 14. Removing the Controller Board

.

Step 5: Align the new controller with the mounting holes. Secure

the new controller board using the existing hardware.

Tighten the screws.

Step 6: Connect the J1, J2, J3, J4, and J6 plugs to their original

receptacles.

Step 7: Reconnect the wires to J7 and J8.

Step 8: Reapply power to the transfer switch.

Step 9: Place the generator control selector switch in the “AUTO”

position after the controller has been replaced. (The Gen-

erator may start but will shut down with in 5 minutes.)

Test the system for proper functionality.

7.4.1.2 100 A Neutral Bar

Figure 15. 100 A Neutral Bar.

Step 1: Turn the utility (Source 1) power off and turn the genera-

tor (Source 2) control selector switch to the “OFF” posi-

tion before attempting to replace the neutral bar.

Step 2: Disconnect all wire cables from the neutral bar.

Step 3: Remove the two screws in the black base using a blade

screwdriver or 0.375 in. socket or nut driver. Remove the

strap with a common straight blade screw driver and then

remove the neutral bar.

Figure 16. Replacing the 100 A Neutral Bar.

Step 4: Mount the neutral bar to the base plate using the hard-

ware supplied.

Step 5: Reattach the strap to the new neutral bar.

Step 6: Reconnect all wire cables to the neutral bar.

Step 7: Apply utility (Source 1) power and place the generator

control selector switch in the “AUTO” position after the

neutral bar has been replaced. Test the system for

proper functionality.

CONNECTORS

MOUNTING

SCREWS

J1-J4

J6

J7

J8

NEUTRAL BARS

SCREWS

Instructional Booklet

Page 18 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

For more information visit: www.eaton.com IB70-8671

7.4.1.3 Ground Bar

Figure 17. Replacing the Ground Bar.

Step 1: Turn the utility (Source 1) power off and turn the genera-

tor (Source 2) control selector switch to the “OFF” posi-

tion before attempting to replace the ground bar

Step 2: Disconnect all wire cables from the ground bar.

Step 3: Remove the screws securing the ground bar using a blade

screwdriver or 0.375 in. socket or nut driver (see

Figure 17). Remove the ground bar.

Step 4: Secure the new ground bar to the base plate using the

hardware supplied.

Step 5: Reconnect all wire cables to the ground bar.

Step 6: Apply utility (Source 1) power and place the generator

control selector switch in the “AUTO” position after the

ground bar has been replaced. Test the system for proper

functionality.

7.4.1.4. Replacing the Contactor

Figure 18. Replacing the Contactor.

Step 1: Turn the utility (Source 1) power off and turn the genera-

tor (Source 2) control selector switch to the “OFF” posi-

tion before attempting to replace the contactor.

Step 2: Note their location then disconnect the twelve (12) red

wires from the contactor (see Figure 18).

Note: All wires connected to the contactor are labeled to ease

identification.

Step 3: Remove the four (4) screws securing the contactor to the

base plate using a blade screwdriver or 0.25 in. socket or

nut driver. Remove the contactor.

Step 4: Following the replacement steps for the 100 A lugs (see

Sections 7.4.1.6), remove the lugs from the old contactor

then install the lugs on the new contactor.

Step 5: Secure the contactor onto the base plate using the hard-

ware supplied.

Step 6: Reattach the twelve (12) red wires to the contactor.

Examine each wire to find the name then refer to Figure

18 for the correct connection point.

Step 7: Reconnect all wire cables to the contactor as per their

original connections.

Step 8: Apply utility (Source 1) power and place the generator

control selector switch in the “AUTO” position after the

contactor has been replaced. Test the system for proper

functionality.

MOUNTING

SCREWS

GROUND BAR

N2

N1

E2

E1

UTILITY

COIL

GENERATOR

COIL

GENERATOR AUX.

SWITCH

UTILITY AUX.

SWITCH

IB70-8671 For more information visit: www.eaton.com

Instructional Booklet

Effective: July 2008 Page 19

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

7.4.1.5 Wiring Harness

Figure 19. Wiring Harness Installed in a EGS ATS.

Step 1: Turn the utility (Source 1) power off and turn the genera-

tor (Source 2) control selector switch to the “OFF” posi-

tion before attempting to replace the wiring harness.

Step 2: Note their location then disconnect the red wires from the

contactor.

Note: All wires connected to the contactor are labeled to ease identifica-

tion.

Figure 20. Wires to Disconnect from the Contactor.

Step 3: Disconnect the J1, J2, J3, J4, J6, J7, and J8 plugs from

the controller (see Figure 14).

The wire harness is now free to be removed.

Step 4: Place the new wiring harness in the ATS.

Step 5: Connect the J1 through J8 plugs to the controller.

Step 6: Reattach the red wires to the contactor. Examine each

wire to find the name then refer to Figure 20 for the cor-

rect connection point.

Step 7: Apply utility (Source 1) power and place the generator

control selector switch in the “AUTO” position after the

wiring harness has been replaced. Test the system for

proper functionality.

7.4.1.6 Replacing the 100 A Lugs

Figure 21. Replacing the 100 A Lugs.

Step 1: Turn the utility (Source 1) power off and turn the genera-

tor (Source 2) control selector switch to the “OFF” posi-

tion before attempting to replace the lugs.

Step 2: Disconnect all wire cables from the contactor.

Step 3: Note their location then disconnect the red wires from the

contactor (see Figure 18).

Note: All wires connected to the contactor are labeled to ease

identification.

UTILITY COIL

CONNECTIONS

UTILITY

AUX

COM.

UTILITY

AUX

N.C.

GEN

AUX

N.C.

GEN

AUX

COM

GENERAL

COIL

CONNECTIONS

E1

E2

N1

N2

LOAD LUGS

GENERATOR

LUGS

UTILITY

LUGS

Instructional Booklet

Page 20 Effective: July 2008

O & M Manual for the EGS AutomaticTransfer Switch

with RTC-50 Control and Integral Loadcenter - 100 Amp

For more information visit: www.eaton.com IB70-8671

For All ATSs

Step 4: Remove the four (4) screws securing the contactor to the

base plate using a blade screwdriver or 0.25 in. socket or

nut driver.

Step 5: Remove the two (2) generator lugs and the two (2) load

lugs using a blade screwdriver (see Figure 21).

Step 6: Once the load lugs have been removed, insert a blade

screwdriver up through the circular hole in the load lug

bus and remove screws securing the two (2) generator

lugs.

Step 7: Place the new utility lugs on the utility bus so the anti-

turn protrusions fit in the holes. Once the lugs are in

place, take one (1) supplied control wire terminal and

hold it underneath the bus. Using one (1) screw and one

(1) washer supplied, tighten the control wire terminal and

lug to the utility bus. Repeat the process of the second

utility lug. Ensure that no gaps are present between the

lugs and bus.

Step 8: Place the new generator lugs on the generator bus.

Once the lugs are in place, take one (1) supplied control

wire terminal and hold it underneath the bus. Using one

(1) screw and one (1) washer supplied, tighten the con-

trol wire terminal and lug to the generator bus. Repeat

the process of the second generator lug. Ensure that no

gaps are present between the lugs and bus.

Step 9: Secure the load lugs to the load bus using the hardware

supplied.

Note: The load lugs do not require control wire terminals.

Step 10: Secure the contactor to the base plate using the four (4)

screws supplied.

Step 11: Reattach the red wires to the contactor. Examine each

wire to find the name then refer to Figure 21 for the cor-

rect connection point.

Step 12: Reconnect all cables to the contactor as per their original

connections.

Step 13: Apply utility (Source 1) power and place the generator

control selector switch in the “AUTO” position after the

lugs have been replaced. Test the system for proper

functionality.

7.5 Troubleshooting

Table 5 contains troubleshooting information for the EGS ATS. If

a problem still exists after completing the troubleshooting proce-

dures, contact an authorized Eaton sales representative.

Table 5. Troubleshooting Chart.

PROBLEM CAUSE CORRECTION

The automatic transfer switch does not transfer to the generator. 1. The generator breaker is open.

2. The generator voltage is not acceptable.

1. Reset the generator circuit breaker.

2. Refer to the generator User's Manual.

The automatic transfer switch does not transfer to the utility. 1. The service disconnect breaker is open.

2. The utility voltage is not acceptable.

1. Reset the service disconnect breaker.

2. Wait for the utility voltage to return to normal.

The generator is still running after the transfer switch transfers to the utility. Engine cool down period. The engine should stop after the cool down.

La page charge ...

Eaton EGS100L24R Manuel utilisateur

Ce manuel convient également à

Eaton EGS100L24R Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents