C2G UPS Online Le manuel du propriétaire

Marque: C2G

Modèle: UPS Online

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Online UPS

1KVA | 1.5KVA | 2KVA | 3KVA Models

Uninterruptible Power Supply System

User Manual

I-00884 Rev A

Table of Contents

Important Safety Warnings ..................................................................................................... 3

Transportation and Storage............................................................................................................................................. 3

Preparation ...................................................................................................................................................................... 3

Installation ....................................................................................................................................................................... 3

Operation ........................................................................................................................................................................ 4

Maintenance, Service and Faults ..................................................................................................................................... 4

Avertissements de sécurité importants .................................................................................... 5

Transport et stockage ...................................................................................................................................................... 5

Préparation ...................................................................................................................................................................... 5

Installation ....................................................................................................................................................................... 6

Fonctionnement .............................................................................................................................................................. 6

Maintenance, Service et Défauts .................................................................................................................................... 7

1. Installation and Setup .......................................................................................................... 9

Unpacking and Inspection ............................................................................................................................................... 9

Rear Panel ...................................................................................................................................................................... 10

Operating Principle ........................................................................................................................................................ 11

Installing the UPS ........................................................................................................................................................... 11

Setting Up the UPS ........................................................................................................................................................ 12

Battery Replacement ..................................................................................................................................................... 15

Replacement Battery Assembly ..................................................................................................................................... 15

2. Operations ......................................................................................................................... 18

Button Operations ......................................................................................................................................................... 18

LCD Panel ....................................................................................................................................................................... 19

Audible Alarms .............................................................................................................................................................. 20

LCD Panel Index ............................................................................................................................................................. 21

Operating Mode Descriptions ....................................................................................................................................... 22

UPS Settings ................................................................................................................................................................... 23

Fault Reference Codes ................................................................................................................................................... 29

Warning Indicators ........................................................................................................................................................ 30

3. Troubleshooting ................................................................................................................. 31

4. Maintenance and Storage ................................................................................................... 33

Maintenance ................................................................................................................................................................. 33

Storage .......................................................................................................................................................................... 33

5. Specifications ..................................................................................................................... 34

Input .............................................................................................................................................................................. 34

Output ........................................................................................................................................................................... 34

Efficiency ....................................................................................................................................................................... 34

Battery ........................................................................................................................................................................... 35

Physical .......................................................................................................................................................................... 35

Environment .................................................................................................................................................................. 35

Management ................................................................................................................................................................. 35

Expandable Battery Box Specification ........................................................................................................................... 36

Important Safety Warnings

Comply with all warnings and operating instructions in this manual and save it for future reference. Do not

operate this unit before carefully reading through all safety information and operating instructions.

Transportation and Storage

Transport the UPS system only in the original package to protect against shock and impact.

The UPS must be stored in a ventilated and dry room.

Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environments. The

UPS system must be absolutely dry before being installed. Please allow at least two hours for the UPS

system to adjust to the environment.

Do not install the UPS system near water or in damp environments.

Do not install the UPS system where it would be exposed to direct sunlight or near a heater.

Do not block ventilation holes on the UPS housing.

Installation

Do not connect appliances or devices to the UPS output sockets or terminal that would over load the

UPS.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UPS output sockets.

Connect the UPS system only to a grounded, shockproof outlet, which must be easily accessible and

close to the UPS system.

Use only a VDE-tested, CE-marked (or UL-marked for 100/110/115/120/127 Vac models) mains cable

(e.g. the mains cable of your computer) to connect the UPS system to the building wiring outlet (shockproof

outlet).

Use only VDE-tested, CE-marked (or UL-marked for 100/110/115/120/127 Vac models) power cables

to connect the loads to the UPS system.

When installing the equipment, ensure that the sum of the leakage current of the UPS and the

connected devices does not exceed 3.5mA.

Temperature Rating: Units are considered acceptable for use in a maximum ambient environment of

104°F (40°C).

For Pluggable Equipment: The socket-outlet shall be installed near the equipment and shall be easily

accessible.

The unit is heavy. Lifting the unit requires a minimum of two people.

Operation

Do not disconnect the ground conductor cable on the UPS or the building wiring terminals at any time

since this would cancel the protective earth of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries), therefore, the UPS output

sockets or output terminal blocks may be electrically live even if the UPS system is not connected to the

building wiring outlet.

In order to fully disconnect the UPS system, first press the “OFF” button, and then disconnect the

mains.

Ensure that no liquid or other foreign objects can enter into the UPS system.

The EPO, RS-232 and USB circuits are an IEC 60950-1 safety extra low voltage (SELV) circuit. This

circuit must be separated from any hazardous voltage circuits by reinforced insulation.

Maintenance, Service and Faults

The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified

maintenance personnel.

Risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet);

components inside the UPS system are still connected to the battery and are electrically live and dangerous.

Before performing any service and/or maintenance, disconnect the batteries and verify that no

current is present and no hazardous voltage exists on the terminals of the high capability capacitor, such as

BUS-capacitors.

Only persons are adequately familiar with batteries and with the required precautionary measures

may replace batteries and supervise operations. Unauthorized persons must be kept well away from the

batteries.

Risk of electric shock. The battery circuit is not isolated from the input voltage. Hazardous voltages

may occur between the battery terminals and the ground. Before touching, please verify that no voltage is

present.

Do not dispose of batteries in a fire. The batteries may explode.

Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be

toxic.

Batteries may cause electric shock and have a high short-circuit current. Please take the

precautionary measures specified below and any other measures necessary when working with batteries:

• Remove watches, rings, or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

• Disconnect charging source and load prior to installing or maintaining the battery.

• Remove battery grounds during installation and maintenance to reduce likelihood of shock. Remove the

connection from ground if any part of the battery is determined to be grounded.

When changing batteries, install the same number and same type of batteries or battery packs.

For UPS with internally mounted battery:

• Instructions shall have sufficient information to enable the replacement of the battery with a suitable

manufacturer and catalogue number.

• Safety instructions to allow access by Service Personnel shall be stated in the installation/service

handbook.

• If batteries are to be installed by Service Personnel, instructions for interconnections, including terminal

torque, shall be provided.

Do not attempt to dispose of batteries by burning them. This could cause an explosion.

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and eyes. It may

be toxic.

Only replace the fuse with the same type and amperage to avoid fire hazards.

Do not disassemble the UPS system.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This is a product for commercial and industrial applications. In second environment installations,

restrictions or additional measures may be needed to prevent disturbances.

Avertissements de sécurité importants

Respectez tous les avertissements et consignes d'utilisation de ce manuel et conservez-le pour référence

ultérieure. Ne faites pas fonctionner cet appareil avant de lire attentivement toutes les informations de

sécurité et les instructions d'utilisation.

Transport et stockage

Transportez le système UPS uniquement dans son emballage d'origine pour le protéger contre les

chocs.

L'onduleur doit être stocké dans une pièce ventilée et sèche.

Préparation

De la condensation peut se produire si le système UPS est directement déplacé d'un environnement

froid à un environnement chaud. Le système UPS doit être absolument sec avant d'être installé. Veuillez

prévoir au moins deux heures pour que le système d'ASI s'adapte à l'environnement.

N'installez pas l'onduleur à proximité d'eau ou dans un environnement humide.

N'installez pas le système UPS à un endroit exposé à la lumière directe du soleil ou à proximité d'un

appareil de chauffage.

Ne bloquez pas les trous de ventilation sur le boîtier de l'onduleur.

Installation

Ne connectez pas de périphériques à la sortie de l'onduleur ou à un terminal susceptible de

surcharger l'onduleur.

Placez les câbles de manière à ce que personne ne puisse marcher dessus ou trébucher dessus.

Ne connectez pas d'appareils domestiques tels que des sèche-cheveux aux prises de sortie de l'ASI.

Ne connectez le système ASI qu'à une prise de terre protégée contre les chocs, qui doit être

facilement accessible et proche du système ASI.

Utilisez uniquement un câble d'alimentation certifié VDE, marqué CE (ou portant la marque UL pour

les modèles 100/110/115/120/127 Vac; par exemple, le câble d'alimentation de votre ordinateur) pour

connecter le système UPS au câblage du bâtiment sortie (sortie antichoc).

Utilisez uniquement des câbles d'alimentation VDE, marqués CE (ou marqués UL pour les modèles

100/110/115/120/127 Vac) pour connecter les charges au système UPS.

Lors de l'installation de l'équipement, assurez-vous que la somme du courant de fuite de l'onduleur et

des périphériques connectés ne dépasse pas 3.5 mA.

Température nominale: Les unités sont considérées acceptables pour une utilisation dans un

environnement ambiant maximal de 40°C (104°F).

Pour les équipements enfichables: La prise de courant doit être installée près de l'équipement et doit

être facilement accessible.

L'unité est lourde. Le levage de l'unité nécessite un minimum de deux personnes.

Fonctionnement

Ne déconnectez pas le câble du conducteur de mise à la terre de l'onduleur ou des bornes de câblage

du bâtiment car cela annulerait la mise à la terre de protection de l'onduleur et de toutes les charges

connectées.

Le système ASI dispose de sa propre source de courant interne (batteries). Par conséquent, les prises

de sortie ou les borniers de sortie de l'ASI peuvent être sous tension même si le système ASI n'est pas

connecté à la sortie du bâtiment.

Pour déconnecter complètement le système UPS, appuyez d'abord sur le bouton "OFF", puis

débranchez le secteur.

Assurez-vous qu'aucun liquide ou autre corps étranger ne puisse pénétrer dans le système ASI.

L'UPS peut être utilisé par des personnes sans expérience préalable.

Maintenance, Service et Défauts

Le système UPS fonctionne avec des tensions dangereuses. Les réparations ne peuvent être

effectuées que par du personnel de maintenance qualifié.

Risque de choc electrique. Même après que l'appareil est déconnecté du secteur (prise de câblage du

bâtiment); les composants à l'intérieur du système UPS sont toujours connectés à la batterie et sont sous

tension et dangereux.

Avant d'effectuer toute opération de maintenance, déconnectez les batteries et vérifiez qu'il n'y a pas

de courant et qu'aucune tension dangereuse n'existe sur les bornes du condensateur haute capacité, telles

que les condensateurs BUS.

Seules des personnes connaissent bien les batteries et, avec les mesures de précaution requises,

peuvent les remplacer et superviser les opérations. Les personnes non autorisées doivent être tenues à

l'écart des batteries.

Risque de choc electrique. Le circuit de la batterie n'est pas isolé de la tension d'entrée. Des tensions

dangereuses peuvent se produire entre les bornes de la batterie et le sol. Avant de toucher, vérifiez s'il n'y a

pas de tension.

Ne jetez pas les piles dans un feu. Les piles peuvent exploser.

N'ouvrez pas et ne mutilez pas les piles. L'électrolyte libéré est nocif pour la peau et les yeux. Cela

peut être toxique.

Les batteries peuvent provoquer un choc électrique et un courant de court-circuit élevé. Veuillez

prendre les mesures de précaution suivantes et toutes les autres mesures nécessaires lorsque vous travaillez

avec des batteries:

• Retirez les montres, bagues ou autres objets métalliques.

• Utilisez des outils avec des poignées isolées.

• Portez des gants et des bottes en caoutchouc.

• Ne posez pas d'outils ou de pièces métalliques sur les batteries.

• Débranchez la source de charge avant d'installer ou de maintenir la batterie.

• Retirez les masses de la batterie pendant l'installation et la maintenance afin de réduire les risques de

choc. Retirez la connexion de la masse si une partie de la batterie est déterminée pour être mise à la

terre.

Lorsque vous changez les piles, installez le même numéro et le même type de piles ou de batteries.

Pour onduleur avec batterie interne:

• Les instructions doivent contenir suffisamment d'informations pour permettre le remplacement de la

batterie par un fabricant et un numéro de catalogue appropriés.

• Les instructions de sécurité pour permettre l'accès au personnel de service doivent être indiquées dans

le manuel d'installation/d'entretien.

• Si des batteries doivent être installées par le personnel de service, des instructions pour les

interconnexions, y compris le couple aux bornes, doivent être fournies.

N'essayez pas de vous débarrasser des piles en les brûlant. Cela pourrait provoquer une explosion.

Ne pas ouvrir ou détruire les piles. L'électrolyte qui s'échappe peut causer des blessures à la peau et

aux yeux. Cela peut être toxique.

Ne remplacez le fusible que par le même type et le même ampérage pour éviter les risques

d'incendie.

Ne démontez pas le système UPS.

Cet équipement a été testé et déclaré conforme aux limites d'un appareil numérique de classe A,

conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection

raisonnable contre les interférences nuisibles lorsque l'équipement est utilisé dans un environnement

commercial. Cet équipement génère, utilise et peut émettre de l'énergie radiofréquence et, s'il n'est pas

installé et utilisé conformément au manuel d'instructions, peut causer des interférences nuisibles aux

communications radio. L'utilisation de cet équipement dans une zone résidentielle est susceptible de

provoquer des interférences nuisibles, auquel cas l'utilisateur devra corriger les interférences à ses propres

frais.

Les changements ou modifications non expressément approuvés par la partie responsable de la

conformité pourraient annuler l'autorité de l'utilisateur à utiliser l'équipement.

Ceci est un produit pour les applications commerciales et industrielles. Dans les installations du

deuxième environnement, des restrictions ou des mesures supplémentaires peuvent être nécessaires pour

éviter les perturbations.

1. Installation and Setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.

Please keep the original package in a safe place for future use.

Unpacking and Inspection

Unpack your products and inspect the contents. The contents should include the following supplied

components and hardware.

1-3KVA

UPS Unit

User Manual

USB Cable

(2x) UPS Mounting Brackets

(4x) Foot

NOTE:

• Rail Slider is provided. For more information, refer to the 2U Rackmount Rail Slider instruction sheet

(I-00888.pdf).

• Before installation, inspect all supplied components and hardware to ensure nothing was damaged

during transportation. If you notice any damaged or missing parts, do not turn on the unit and notify

the carrier and utilize the support reference number provided on your unit. Please keep the original

package in a safe place for future use.

Rear Panel

1K and 1.5K Models

2K Models

3K Models

Label Descriptions:

1. Programmable Outlets: Connect to non-critical loads.

2. Output Receptacles: Connect to critical loads.

3. AC Input

4. Network/Fax/Modem Surge Protection

5. USB Communication Port

6. RS-232 Communication Port

7. SNMP Intelligent Slot

8. EPO (Emergency Power Off) Function Connector

9. External Battery Connection

Operating Principle

The operating principle of the UPS is shown as follows:

The UPS is composed of a mains input, EMI/RFI filters, rectifier/PFC, inverter, battery charger, DC-to-DC

converter, battery, dynamic bypass and UPS output.

Installing the UPS

For safety considerations, the UPS ships from the factory without the battery wires connected. Before

installing the UPS, please use the following steps to first re-connect the battery wires.

Step 1: Remove the front panel.

Step 2: Connect the AC input

and re-connect the battery

wires.

Step 3: Put the front panel back on

the unit.

This UPS can be either placed on a surface or mounted in a 19” rack chassis.

Rackmount Installation

CAUTION: Do not use the mounting brackets to lift the unit. Use the mounting brackets only for

securing the unit to the rack.

ATTENTION: N'utilisez pas les supports de montage pour soulever l'appareil. Utilisez les supports de

montage uniquement pour fixer l'unité au rack.

NOTE: Rail Slider is provided. For more information, refer to the 2U Rackmount Rail Slider instruction sheet

(I-00888.pdf).

Use the following steps to mount your UPS system into a 19” rack.

Step 1 Step 2

Tower Installation

Step 1

Step 2

Step 3

NOTE: When using feet for tower installations of the UPS or battery pack, ensure a 2.76” (70mm) distance

from the edge of the unit to the feet as follows.

Setting Up the UPS

Before installing the UPS, please read the following to select the proper location.

1. The UPS should be placed on a flat, clean surface. Place it in an area away from vibration, dust,

humidity, high temperature, flammable liquids, gases, corrosive, and conductive contaminants. Install

M4 Screw

Tower Stand

2.76”

(70mm)

2.76”

(70mm)

the UPS indoors in a clean environment, where it is away from windows and doors. Maintain a minimum

clearance of 3.94 in. (100mm) on the bottom of the UPS to avoid dust and high temperatures.

2. Maintain an ambient temperature range of 32ºF (0ºC) to 113ºF (45ºC) for optimal UPS operation. For

every 41ºF (5ºC) above 113ºF (45ºC), the UPS will derate 12% of nominal capacity at full load. The

highest working temperature requirement for operation is 122ºF (50ºC).

3. It is required to maintain a maximum altitude of 1093.61yd. (1000m) to keep the UPS within normal

operation at full load. If used in high altitudes, please reduce the connected load. Altitude derating

power with connected loads for UPS normal operation is listed as follows:

Altitude (Feet and Meters) Derating Factor

3280.84 1000 1.0

4921.26 1500 0.95

6561.68 2000 0.91

8202.1 2500 0.86

9842.52 3000 0.82

11482.94 3500 0.78

13123.36 4000 0.74

14763.78 4500 0.7

16404.2 5000 0.67

NOTE: Based on density of dry air = 1.225 kg/m

at sea level, + 59˚F (15˚C).

4. UPS Placement

Your UPS is equipped with a fan for cooling. Therefore, place the UPS in a well-ventilated area. It’s

required to maintain minimum clearance of 4” (100mm) in the front of the UPS, and 12” (300mm) at the

back and two sides of the UPS, for heat dissipation and easy-maintenance.

UPS Input Connection

CAUTION: Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using

extension cords.

ATTENTION: Branchez l'onduleur dans une prise bipolaire, trois fils et mise à la terre uniquement.

Évitez d'utiliser des rallonges.

• The power cable is attached to the UPS. The input plug is a NEMA 5-15P for 1K and 1.5K models, NEMA

5-20P for 2K model and NEMA 5-30P for 3K model.

NOTE: Check if the site wiring fault indicator lights up on the LCD panel. It will be illuminated when the UPS

is plugged into an improperly wired utility power outlet. For more information, see “Troubleshooting” on

page 31. Please also check if there is a circuit breaker against overcurrent and short circuit between the

mains and AC input of the UPS for safe operation. The recommended protection values are as follows:

• 15A for the 1K and 1.5K models

• 20A for 2K model

• 30A for 3K model

UPS Output Connections

There two kinds of outputs: programmable outlets and general outlets. Please connect non-critical devices

to the programmable outlets and critical devices to the general outlets. During a power failure, you may

extend the backup time to critical devices by setting a shorter backup time for non-critical devices.

Communication Connection

Communication Ports:

USB Port RS-232 Port Intelligent Slot

To allow for unattended UPS shut down, start, and status monitoring, connect one end of the

communication cable to the USB/RS-232 port and the other end to the communication port on your PC. With

the monitoring software installed, you can schedule your UPS to shut down or start, and monitor your UPS

status from your PC.

The UPS is equipped with an intelligent slot for attaching either an SNMP or an AS400 card. When installing

either card in the UPS, it will provide advanced communication and monitoring options.

Making Network Connections

Network, Phone, or Fax Surge Ports

Connect a single modem, phone, or fax line into the surge-protected “IN” outlet on the back panel of the

UPS unit. Connect from the “OUT” outlet to your equipment with another modem, phone, or fax line cable.

Disabling and Enabling the EPO Function

The UPS is equipped with an EPO (emergency power off) function. By default, the UPS is delivered from the

factory with a metal plate connecting Pin 1 and Pin2, which disables the EPO function. To activate the EPO

function, loosen the two screws and remove metal plate from the EPO port.

NOTE: The EPO function’s logic is set up via LCD settings. For more information, see Program 16 in “UPS

Settings,” on page 22.

Optional Expandable Battery Connection

Connect one end of the external battery cable into your UPS and the other end into the battery box. Use the

following illustration to connect your expandable battery.

CAUTION: External battery connections must only be performed by qualified service technicians.

ATTENTION: Les connexions de batterie externes doivent uniquement être effectuées par des

techniciens de maintenance qualifiés.

NOTE: For more information, refer to the Expandable Battery Box User Manual (I-00890.pdf).

Turning on the UPS

Press the ON/Mute button on the front panel for two seconds to power on your UPS.

UPS

Battery Box

NOTE: The battery charges fully during the first five hours of normal operation. Do not expect full battery

operation capability during this initial charge period.

Installing the UPS Monitoring Software

For optimal computer system protection, install the UPS monitoring software to fully configure your UPS

shutdown procedure. Then, use the following steps to install the UPS monitoring software.

1. Download the UPS monitoring software from www.legrand.us/upsdownloads

and then follow the

on-screen instructions.

2. When your computer restarts, the monitoring software will appear as an orange plug icon located in the

system tray, near the clock.

Battery Replacement

NOTE: This UPS is equipped with internal batteries and user can replace the batteries without shutting

down the UPS or connected loads (a hot-swappable battery design). Replacement is a safe procedure,

isolated from electrical hazards.

CAUTION: Consider all warnings, cautions, and notes before replacing batteries.

ATTENTION: Tenez compte de tous les avertissements, mises en garde et remarques avant de

remplacer les piles.

NOTE: After disconnecting the battery, your connected equipment is not protected from power outages.

Step 1: Remove the front panel. Step 2: Disconnect the battery

wires.

Step 3: Pull out the battery box by

removing the two screws on the front

panel.

Step 4: Remove the top cover of

the battery box and replace the

batteries inside.

Step 5: After replacing the

batteries, put the battery box

back in the original location and

replace the two screws.

Step 6: Re-connect the battery

wires.

Step 7: Put the front panel

back on the unit.

Replacement Battery Assembly

NOTE: Assemble the battery kit first before installing it inside of your UPS. Select from the following battery

kit procedures for proper assembly.

2 Cell Battery Kit

Step 1: Thoroughly remove

old adhesive tape

and install new tape in the following locations.

Step 2: Connect all battery terminals as shown.

Step 3: Place the connected battery packs on

adhesive strips on one side of the plastic shells.

Step 4: Cover the other side of the

plastic shell as

shown.

3 Cell Battery Kit

Step 1: Thoroughly remove

old adhesive tape

and install new tape in the following locations.

Step 2: Connect all battery terminals as shown.

Step 3: Place the assembled battery packs on

adhesive strips on one side of the plastic shells.

Step 4: Cover the other side of the

plastic shell as

shown.

Tape

4 Cell Battery Kit

Step 1: Thoroughly remove

old adhesive tape

and install new tape in the following locations.

Step 2: Connect all battery terminals as shown.

Step 3: Place the assembled battery packs on

adhesive strips on one side of the plastic shells.

Step 4: Cover the other side of the

plastic shell as

shown.

6 Cell Battery Kit

Step 1: Thoroughly remove

old adhesive tape

and install new tape in the following locations.

Step 2: Connect all battery terminals as shown.

Step 3: Place the assembled battery packs on

adhesive strips on one side of the plastic shells.

Step 4: Cover the other side of the

plastic shell as

shown.

Tape

2. Operations

Button Operations

Button Function

• Turn on the UPS: Press and hold this button for at least 2 seconds to turn on the

UPS.

• Mute the alarm: While the UPS is turned on and in battery mode, press and hold

this button for at least 3 seconds to disable or enable the alarm system. This

function is overridden by warning or error alerts.

• Up key: Press this button to display the previous selection when in the UPS settings

mode.

• Switch to UPS self-test mode: While in AC mode, ECO (efficiency corrective

optimizer) mode, or converter mode, press this button for 3 seconds.

• Turn off the UPS: Press and hold this button at least 2 seconds to turn off the UPS.

This puts the UPS in standby mode under normal power. If bypass is enabled, this

function will transfer the unit into bypass mode.

• Confirm selection key: Press this button to confirm your selection while in the UPS

settings mode.

• Switch LCD Parameter 1 message: Press this button to change the LCD message

from input voltage, input frequency, input current, battery voltage, battery current,

battery capacity, ambient temperature, output voltage, output frequency, load

current, and load percent choices.

• Settings mode: When in Standby or Bypass mode, press and hold this button for 3

seconds to enter the UPS settings mode.

• Down key: Press this button to display the next selection when in the UPS settings

mode.

• Switch to bypass mode: When the main power is normal, press and hold both of

these buttons simultaneously for 3 seconds. The UPS then enters bypass mode.

This action does not work when the input voltage is out of an acceptable range.

• Exit settings mode or return to the upper menu: When working in settings mode,

press and hold both of these buttons simultaneously for 0.2 seconds to return to

the previous menu. If you are already in the top menu, press these two buttons at

the same time to exit the settings mode.

LCD Panel

Backup Time Information

Display Function

Indicates the backup time.

Indicates the estimated backup time.

H: hours, M: minute

Warning and Fault Information

Display Function

Indicates that the a warning and/or fault has occurred.

Indicates the warning and fault codes. For more information, see

“Fault Reference Codes,” on page 29 and “Warning Indicators,” on

page 30.

Setting Operation

Display Function

Indicates the selected UPS setting program. For more information,

see “UPS Settings” on page 23.

Input, Battery, Temperature, Output, and Load Information

Display Function

Indicates the input voltage, input frequency, input current, battery

voltage, battery current, battery capacity, ambient temperature,

output voltage, output frequency, load current, and load percent.

k: kilo, W: watt, V: voltage, A: ampere, %: percent, ℃: centigrade degree, Hz:

frequency

Load Information

Display Function

Indicates the load level by 0-24%, 25-49%, 50-74%, and 75-100%.

Indicates an overload has occurred.

UPS Status

Display Function

Indicates the UPS connects to the mains.

Indicates the battery is working.

Indicates the AC to DC circuit is working.

Indicates the inverter circuit is working.

Indicates the output is working.

Indicates that programmable outlets are working.

Indicates the bypass circuit is working.

Indicates the ECO (efficiency corrective optimizer) mode is enabled.

Indicates the PFC circuit is working.

Indicates the UPS is working in converter mode.

Indicates the battery charger is working.

Indicates the UPS alarm is disabled.

Battery Information

Display Function

Indicates the battery level by 0-24%, 25-49%, 50-74%, and

75-100%.

Indicates the battery life is low.

Audible Alarms

Reason Sound

Battery Mode Sounding every 5 seconds

Low Battery Sounding every 2 seconds

Overload Sounding every second

Fault Continuously sounding

Bypass Mode Sounding every 10 seconds

La page charge ...

C2G UPS Online Le manuel du propriétaire

Marque: C2G

Modèle: UPS Online

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: C2G UPS Online Owner's manual

Documents connexes

C2G Expandable-Battery-Box-I-00890 Le manuel du propriétaire

C2G UPS Online Le manuel du propriétaire

Ce manuel convient également à

C2G UPS Online Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents