Norcold 2118 PolarMax Guide d'installation

Marque: Norcold

Modèle: 2118 PolarMax

Catégorie: Cheminées

Taper: Guide d'installation

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance

or additional information, contact a qualied installer, service agency, or

the gas supplier.

NORCOLD, Inc.

P.O. Box 4248

Sidney, OH 45365-4248

Part No. 636901D(4/1/2020)

English

Installation Manual

for the 2118X series of RV Refrigerators

The letter “X”, in the model numbers above, stands for letters or numerals which means a

refrigerator option.

DO NOT install this refrigerator in below deck marine applications. Do not install this refrigerator in a

xed indoor cabin or other dwelling applications. This refrigerator must use only NORCOLD designed and

approved outside air intake and exhaust ventilation for correct and safe operation. Any other ventilation

could cause lethal combustion exhaust fumes and/or explosive propane gas fumes to be in the living area

and/or to be below deck.

WARNING

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Open Windows

2. Do not attempt to light appliance.

3. Do not touch electrical switches.

4. Extinguish any open ame

5. Shut o fuel supply.

6. Evacuate immediately and call emergency services.

Failure to follow these instructions could result in re or explosion, which could cause

property damage, personal injury, or death.

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors and liquid in the

vicinity of this or any other appliance.

Norcold Customer Support Dept.

Telephone: 800-543-1219

Fax: 734-769-2332

Web Site: www.norcold.com

Installation Manual 2

Table of Contents

Safety Awareness

Safety Awareness ........................................................................................................................................................................................ 2

Safety Instructions ....................................................................................................................................................................................... 3

Certication and Code Requirements.......................................................................................................................................................... 3

Ventilation Requirements............................................................................................................................................................................. 4

Key Refrigerator Dimensions....................................................................................................................................................................... 5

Assemble the Enclosure for the Refrigerator............................................................................................................................................... 5

Install the Lower Intake Vent ....................................................................................................................................................................... 6

Install the Upper Roof Exhaust Vent............................................................................................................................................................ 7

Install the Baes for an Upper Roof Exhaust Vent ..................................................................................................................................... 7

Vertical enclosures ............................................................................................................................................................................... 7

Oset vertical enclosures ..................................................................................................................................................................... 9

Install an Upper Side-Wall Exhaust Vent ................................................................................................................................................... 10

Install the Baes for an Upper Side-Wall Exhaust Vent ............................................................................................................................. 11

Rear Wall Installation ................................................................................................................................................................................. 12

Install Decorative Door Panels (non-metal door models) .......................................................................................................................... 12

Install the Refrigerator ............................................................................................................................................................................... 13

Connect the Electrical Components .......................................................................................................................................................... 14

Connect the 120 volts AC supply ....................................................................................................................................................... 15

Connect the 12 volts DC supply ......................................................................................................................................................... 15

Connect the Low Ambient Heater (optional) .............................................................................................................................................. 15

Connect the Propane Gas Components.................................................................................................................................................... 16

Connect the propane gas supply system ........................................................................................................................................... 16

Examine the propane gas supply system for leaks ............................................................................................................................ 16

Connect the Ice Maker .............................................................................................................................................................................. 17

Connect the water supply line ............................................................................................................................................................ 17

Ignition and Start Up .................................................................................................................................................................................. 18

Ignition and start up ............................................................................................................................................................................ 18

Modes of operation............................................................................................................................................................................. 18

Do a test of the gas safety valve ....................................................................................................................................................... 19

Shut down.................................................................................................................................................................................................. 19

Fault Codes ............................................................................................................................................................................................... 20

Read this manual carefully and understand the contents before you install the refrigerator.

Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows

the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their

meanings. They are for your safety.

This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much

property damage.

This signal word means a hazard, which if ignored, can cause small personal injury or much property

damage.

WARNING

CAUTION

Installation Manual 3

Certication and Code Requirements

Safety Instructions

- This refrigerator is not approved for use as a free standing refrigerator. It is equipped for the use of propane gas only

and can not be changed to use any other fuels (natural gas, butane, etc.).

- Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property

damage, or both.

- Obey the instructions in this manual to install intake and exhaust vents.

- Do not install the refrigerator directly on carpet. Put the refrigerator on a metal or wood panel that extends the full

width and depth of the refrigerator.

- Do not allow anything to touch the refrigerator cooling system.

- Propane gas can ignite and cause an explosion that can result in property damage, personal injury, or death. Do not

smoke or create sparks. Do not use an open ame to examine the propane gas supply line for leaks. Always use two

wrenches to tighten or loosen the propane gas supply line connections.

- Make sure the electrical installation obeys all applicable codes. See “Certication and Code Requirements” section.

- Do not bypass or change the refrigerator’s electrical components or features.

- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically

conductive and can cause a shock hazard, electrical shorts, and in some cases re.

- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system.

- The cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The

cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not

bend, drop, weld, move, drill, puncture, or hit the cooling system.

- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, use caution and wear cut resistant gloves.

- Make sure that the refrigerator is stored in a location so that it is not exposed to the elements of the weather.

This refrigerator is certied by CSA International as meeting the

latest edition of ANSI Z21.19 / CSA 1.4 standards for installation

in mobile homes or recreational vehicles.

The installation must obey these standards and this “Installation

Manual” for the NORCOLD limited warranty to be in eect.

Installation must conform with the following as applicable:

WARNING

CAUTION

Art01290

Installation Manual 4

Ventilation Requirements

The completed installation must:

- Make sure there is sucient intake of fresh air for combustion.

- Make sure the living space is completely isolated from the combustion system of the refrigerator.

- Make sure there is complete and unrestricted ventilation of the ue exhaust which, in gas mode, can produce carbon

monoxide. The breathing of carbon monoxide fumes can cause dizziness, nausea, or in extreme cases, death.

- Make sure the refrigerator is completely isolated from its heat generating components through the correct use of

baes and panel construction.

Certied installation needs one lower intake vent and one upper exhaust vent. Install the vents exactly as written in this manual. Any

other installation method voids both the certication and the factory warranty of the refrigerator.

The bottom of the opening for the lower intake vent, which is also the service access door, must be even with or immediately below the

oor level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.

CSA International certication allows the refrigerator to have zero (0) inch minimum clearance at the sides, rear, top, and bottom.

While there are no maximum clearances specied for certication, the following maximum clearances are necessary for correct

refrigerator performance:

Bottom 0 inch min. 0 inch max.

Each Side 0 inch min. 1/2 inch max.

Top 0 inch min. 1/4 inch max.

Rear 0 inch min. 1 inch max.

These clearances plus the lower and upper vents allow the natural air draft that is necessary for good refrigeration. Cooler air comes in

through the lower vent, goes up around the refrigerator coils where it removes the excess heat from the refrigerator components, and

goes out through the upper vent.

The refrigerator also has thermostat controlled fans to move air across the cooling system. These fans turn on when the condenser n

temperature at the thermostat is about 130° F or higher and only when the refrigerator controls are on. These fans turn o when the

condenser n temperature at the thermostat is about 115° F or less. Even with these fans, if the air ow is blocked or decreased, the

refrigerator will not cool correctly.

Each NORCOLD model is certied by CSA International for correct ventilation. Install only the certied vents that are listed in this

manual.

In the United States and Canada:

- Local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the Natural Gas and Propane

installation Code, CSA B149.1, ANSI A119.2 Recreational Vehicles Code, and CSA Z240 RV Series, Recreational Vehicles.

- A manufactured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 (part 280), and the

current CSA Z240.4, Gas-equipped Recreational Vehicles and Mobile Housing.

- If an external power source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes

or, in the absence of local codes, the National Electrical code, and ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2.

Parts 1 and 2.

All propane gas supply piping and ttings must obey local, state, and national codes about type and size. These components must also

obey the current NFPA 1192 section 2-4, and in Canada with the current CAN 1-6.10 Standard.

WARNING

Installation Manual 5

Key Refrigerator Dimensions

These key refrigerator dimensions are for your reference as

necessary (See Art02477).

Refrigerator cabinet width w/o trim:

35.6 in..................................... 1

Refrigerator width overall w/ trim:

37.3 in..................................... 2

Refrigerator cabinet to side trim:

.90 in....................................... 3

Refrigerator cabinet height w/o trim:

68.6 in..................................... 4

Refrigerator height overall w/ trim:

70.6 in..................................... 5

Refrigerator cabinet to top trim:

1.20 in................................. 180

Refrigerator bottom rail to bottom trim:

0.80 in................................. 181

Enclosure wall to door fronts:

3.2 in....................................... 7

Refrigerator bottom rail to center of handles:

44.1 in..................................... 8

Assemble the Enclosure for the Refrigerator

1. Make sure the enclosure shelf is solid and level. The enclosure shelf must be:

- a metal or a wood panel and extend the full width and depth of the enclosure.

- able to support the weight of the refrigerator and its contents.

- level to maintain door alignment.

2. Make sure there are no adjacent heat sources such as a furnace vent, a hot water heater vent, etc.

180

181

Art 02477

Installation Manual 6

3. Make sure the enclosure is 68.94 - 69.06 inches high x 35.94 - 36.04 inches wide x 24.00 -

24.13 inches deep.

Measure the enclosure depth [174] from the interior face of the enclosure to the

inside of the rear wall (See ART02478).

4. If there is more than 1/2 inch between either side of the refrigerator and the inside of the

enclosure:

- Fill the space with berglass (batt-type) insulation or add a bae to eliminate the clearance.

- The rear of the batt-type insulation must be between 18 -19 inches from the face of the

enclosure.

- Securely attach the batt-type insulation to the enclosure, so that it remains in this

position during refrigerator installation, if it becomes wet, and in windy conditions.

5. The enclosure face must be perpendicular to the enclosure shelf to provide a combustion

seal.

6. The cutout opening must be square and perpendicular to the enclosure shelf to maintain door alignment.

7. Using the following chart, decide which vents and rough opening (RO) sizes to use:

Certied Vent P/N RO Height RO Width

Upper Roof Exhaust Cap 622293 N/A N/A

625240 N/A N/A

Upper Roof Exhaust Vent 616319 24 in. 5 1/4 in.

625161 24 in. 5 1/4 in.

Upper Exhaust & Lower Intake Plastic 637318 13 3/4 +1/8-0 in 29 7/16 + 1/8 -0 in.

The side vent RO must be square. Diagonal measurements of the RO must be within 1/16 in. The vent should be

centered in the RO width.

Install the Lower Intake Vent

Install the lower intake vent (See Art02479):

The lower intake vent is also the service access opening for the

components on the rear of the refrigerator.

Make sure the bottom of the opening of the lower

intake vent is even with or immediately below the oor

level. This allows any leaking propane gas to escape

to the outside and not to collect at oor level.

- Make sure the bottom of the opening of the lower intake vent [9] is even

with or immediately below the oor level.

- Make sure that the opening for the lower intake vent is between 1/2 inch

and 1 inch [182] from the burner side of the refrigerator enclosure.

NOTICE

WARNING

Art 02478

174

182

ART 02479

NOTICE

Installation Manual 7

1. Install the upper roof exhaust vent.

Make sure that no sawdust, insulation, or other construction

debris is on the refrigerator or in the enclosure. Debris can cause

a combustion hazard and prevent the refrigerator from operating

correctly.

Tighten the screws of the upper roof exhaust cap to 10 inch-pounds max.

Also make sure that the air ow around the upper roof exhaust cap is not

blocked or decreased by other roof mounted features such as a luggage

carrier, an air conditioner, a solar panel, etc.

2. Align the upper roof exhaust vent above the lower intake exhaust vent:

3. Determine the type of enclosure in a vehicle using an upper roof exhaust vent (See

Art02480):

- If the distance from the face of the enclosure to the inboard edge of the roof exhaust vent

opening [169] is more than 17 1/2 inches, install the roof exhaust vent [12] directly above

the condenser [11] of the refrigerator as a vertical enclosure.

- If the distance from the face of the enclosure to the inboard edge of the roof exhaust vent opening [169] is 17 1/2 inches or less,

install the roof exhaust vent [12] inboard from the condenser [11] of the refrigerator as an oset vertical enclosure.

Install an Upper Roof Exhaust Vent

Install the Baes for an Upper Roof Exhaust Vent

Make sure that all horizontal baes are the full width of the inside of the

enclosure and are in the correct location. If the baes are not the full

width of the enclosure or incorrectly located, poor cooling performance

can result.

Vertical enclosures:

If the enclosure depth is 24 inches or more and less than 25 inches (See Art02481):

- Install a top bae [13].

- Make sure there is less than 1/4 inch clearance [15] between the bae and the top of

the refrigerator.

CAUTION

NOTICE

169

Art 02480

Art 02481

Installation Manual 8

If the enclosure depth is 25 inches or more and less than 26 inches

(See Art02482):

- Install a top bae [13].

- Make sure that the top bae is less than 1/4 inch [15] from the top of the

refrigerator.

- Install a condenser bae [16] at the lowest edge of the condenser of the

refrigerator.

- Make sure that the condenser bae is 1 inch or less [19] from the

condenser.

- Install an absorber bae [171] 18 inches to 18 1/2 inches above the bottom

of the enclosure [17] (4 1/4 inches to 4 3/4 inches above the top of the lower

intake vent opening) [18] .

- Make sure that the absorber bae is 1 inch or less [19] from the

absorber.

If the enclosure depth is 26 inches or more (See Art02483):

- Install a top bae [13].

- Make sure that the top bae is less than 1/4 inch [15] from the top of the

refrigerator.

- Install a wood or an aluminum or galvanized sheet solid box bae [21] in the

rear of the enclosure.

- Make sure that the bottom of the solid box bae is 21 inches to 21 1/2

inches above the bottom of the enclosure [17] (71/4 inches to 7 3/4

inches above the top of the lower intake vent opening) [18] .

- Make sure that the back of the solid box bae is perpendicular to the

bottom of the enclosure.

- Make sure that the back of the solid box bae is against the top of the enclosure.

- Make sure that the solid box bae is one inch or less [19] from the coils [10] and

condenser [11] of the refrigerator.

- Make sure that the solid box bae is the full width of the inside of the enclosure.

Art 02482

171

Art 02483

Installation Manual 9

Oset vertical enclosures:

If the enclosure depth is 24 inches or more and less than 25 inches (See Art02484):

- Install an angled top bae [172] between the top rear edge of the refrigerator and the

inside edge of the upper exhaust vent opening.

- Make sure that the angled top bae is less than 1/4 inch [15] from the top of the

refrigerator.

- Make sure that the angled top bae is no more than 45° from vertical [20].

- Install an inside corner bae [173] between the outside edge of the upper exhaust

vent opening and the side wall of the vehicle.

- Make sure that the inside corner bae is approximately parallel to the angled top

bae.

If the enclosure depth is 25 inches or more and less than 26 inches (See Art02485):

- Install an angled top bae [172] between the top rear edge of the refrigerator and the

inside edge of the upper exhaust vent opening.

- Make sure that the angled top bae is less than 1/4 inch [15] from the top of the

refrigerator.

- Make sure that the angled top bae is no more than 45° from vertical [20].

- Install an inside corner bae [173] between the outside edge of the upper exhaust

vent opening and the side wall of the vehicle.

- Make sure that the inside corner bae is approximately parallel to the angled top

bae.

- Install a condenser bae [16] at the lowest edge of the condenser of the

refrigerator.

- Make sure that the condenser bae is 1 inch or less [19] from the condenser.

- Install an absorber bae [171] 21 inches to 21 1/2 inches above the bottom of

the enclosure [17] (21 1/4 inches to 4 3/4 inches above the top of the lower intake

vent opening) [18] .

- Make sure that the absorber bae is 1 inch or less [19] from the absorber.

Art 02484

172

173

Art 02485

173

172

171

Installation Manual 10

If the design of the vehicle does not allow you to install a roof exhaust vent, install an upper

side-wall exhaust vent:

The refrigerator is 23.75 in. min. to 24.05 in. max. from the rear of the breaker

to the rear of the condenser [22] and is 61.35 in. min. to 61.65 in. max. from

the bottom of the refrigerator to the bottom of the refrigerator condenser [23]

(See Art02487).

- Install the upper side-wall exhaust vent [24] so that the distance [25] from the bottom of

the enclosure to the top of the rough opening for the upper exhaust vent is at least 71.0

inches (See Art02487 and Art02488).

- Align the upper exhaust vent horizontally above the lower intake vent [9].

Install an Upper Side-Wall Exhaust Vent

If the enclosure depth is 26 inches or more (See Art02486):

- Install an angled top bae [172] between the top rear edge of the refrigerator and the

inside edge of the upper exhaust vent opening.

- Make sure that the angled top bae is less than 1/4 inch from the top of the

refrigerator.

- Make sure that the angled top bae is no more than 45° from vertical [20].

- Install an inside corner bae [173] between the outside edge of the upper exhaust

vent opening and the solid box bae.

- Make sure that the inside corner bae is approximately parallel to the angled top

bae.

- Install a wood or an aluminum or galvanized sheet solid box bae [21] in the rear of

the enclosure.

- Make sure that the bottom of the solid box bae is 21 inches to 21 1/2 inches

above the bottom of the enclosure [17] (7 1/4 inches to 7 3/4 inches above the

top of the lower intake vent opening) [18] .

- Make sure that the back of the solid box bae is perpendicular to the bottom of

the enclosure.

- Make sure that the back of the solid box bae is either against the top of the

enclosure or against the inside corner bae [173] (depending on the vehicle

design).

- Make sure that the solid box bae is one inch or less from the coils [10] and

condenser [11] of the refrigerator.

- Make sure that the solid box bae is the full width of the inside of the

enclosure.

NOTICE

Art 02486

172

173

Art 02487

Installation Manual 11

Install the Baes for an Upper Side-Wall Exhaust Vent

Make sure that all horizontal baes are the full width of the

inside of the enclosure and are in the correct location. If the

baes are not the full width of the enclosure or incorrectly

located, poor cooling performance can result.

If the enclosure depth is 24 inches or more and less than 26 inches (See Art02488):

- Install a wood, aluminum or galvanized steel top bae [13] between the top of

the refrigerator and the top of the upper exhaust vent [24].

- Make sure that the top bae is less than 1/4 inch [15] from the top of the

refrigerator and bae overlaps the refrigerator 1 inch or less.

- Make sure that the bae is against the wall of the vehicle at the top of the

upper exhaust vent and less than 1/4 inch above the opening for the upper

exhaust vent.

- Install an aluminum or galvanized steel bent-sheet condenser bae [26].

- Make sure that the bend of the condenser bae is the full width of the

inside of the enclosure.

- Make sure that the bend of the condenser bae is ush with the bottom

edge of the door frame of the upper side-wall exhaust vent.

- Make sure that the top edge of the condenser bae is 1/4 inch or less [15]

from the lower rear corner of the condenser.

If the enclosure depth is 26 inches or more (See Art02489):

- Install a wood, aluminum or galvanized steel top bae [13] between the top

of the refrigerator and the top of the upper exhaust vent [24].

- Make sure that the top bae is less than 1/4 inch [15] from the top of

the refrigerator and that the bae overlaps the refrigerator 1 inch or

less.

- Make sure that the bae is against the wall of the vehicle at the top of

the upper exhaust vent and less than 1/4 inch [15] above the opening

for the upper exhaust vent.

- Install a solid box bae [21] between the lower intake vent and the upper

exhaust vent.

- Make the solid box bae either from wood or from an aluminum or

galvanized-steel sheet.

- Make sure that the bottom of the solid box bae is 21 inches to 21 1/2

inches above the bottom of the enclosure [17] (7 1/4 inches to 7 3/4

inches above the top of the lower intake vent opening REF) [18].

- Make sure that the back of the solid box bae is perpendicular to the

bottom of the enclosure.

CAUTION

15 15

Art 02488

15 15

Art 02489

170

Installation Manual 12

The doors are made to accept decorative panels. The decorative panels must be 3/16 inch or less in thickness. Install

the decorative door panels in the refrigerator doors before installing the refrigerator in the vehicle.

1. Make two upper door panels that are 17 1/4 inches wide x 23 1/8 inches

high:

- Raised panels must be centered on each door and no larger than 16

1/2 inches wide x 22 3/8 inches high.

2. Make two lower door panels that are 17 1/4 inches wide x 42 5/16

inches high:

- Raised panels must be centered on each door and no larger than 16

1/2 inches wide x 41 9/16 inches high.

3. Install the decorative door panels:

- Pull the panel retainer [37] o of each door [39] (See Art01804).

- Push a decorative door panel [38] into the slots of each door.

- Make sure that each panel retainer is correctly positioned and push the

curved snaps [125] of the panel retainer [37] inside of the curved snaps [126] of the door (See Art01805).

Install Decorative Door Panels (non-metal door models)

- Make sure that the horizontal top of the solid box bae is even with the bottom edge of the upper exhaust vent [24].

- Make sure the horizontal top edge of the bae is 1/2 inch or less [170] below and 1/4 inch or less behind the lower rear corner

of the condenser [11].

For rear wall installations please refer to special instructions 620918 for additional required instructions.

NOTICE

Art01804

126

125

Art01805

Rear wall Installation

Installation Manual 13

When manually (by hand) or mechanically (by hoist, lift truck, etc.) handling a refrigerator that is not installed in an enclosure, the best

method is while the regerator is in its original packaging.

If the refrigerator is not in its original packaging, use the handling straps [183] of the refrigerator cabinet as the primary load carrying

points (See Art0290). There are two (2) handling straps on both the right and left side of the refrigerator cabinet.

These handling straps may be used to lift, move, and tilt the refrigerator. Norcold recommends that all lifting, moving, and tilting of the

refrigerator is always done by at least 2 persons.

Use only the handling straps to lift, move, or tilt the refrigerator. Using any part of the refrigerator other

than the handing straps, to lift, move, or tilt it can result in damage to the refrigerator.

1. Remove the packaging support block (See Art01850):

- Open both lower doors of the refrigerator.

- Remove and discard the two screws [41] from the front of the lower mounting ange of the refrigerator.

- Tilt the refrigerator back just enough to remove the wooden packaging

support block [209] from behind the lower mounting ange.

- Close the doors.

2. Put the refrigerator completely into the enclosure:

- Push below the center of the refrigerator.

Install the Refrigerator

CAUTION

ART 02490

121

183

Installation Manual 14

- Pull using a wire-form tool hooked into mounting holes [121] of the

refrigerator frame (See Art01808).

Make sure the foam combustion seal is not broken, is

completely around the refrigerator mounting anges,

and is between the mounting anges and the wall of

the enclosure If the seal is not complete, exhaust

fumes can be present in the living area of the vehicle.

The breathing of exhaust fumes can cause dizziness,

nausea, or in extreme cases, death.

3. Put the refrigerator in position:

Be careful when you put the refrigerator into position. It is not

necessary to remove the protective packaging from the doors

of metal door models to install or operate the refrigerator.

- Make sure that the ue cap is not pushed down against the top of the ue

tube.

- Push the refrigerator completely into the enclosure.

4. Install the mounting screws and trim (See Art01814):

- Put the four screws [41] through both the upper and the lower mounting

anges on the front of the refrigerator and into the enclosure wall.

- Push the trim pieces [40] onto the front of the refrigerator.

- Put screws through the mounting ange on the rear of the refrigerator and

into the oor.

5. On metal door models only, you may wish to remove the protective packaging

from the doors.

Be careful to not scratch or dent the metal doors. Do not use

any abrasive cleaners, chemicals, or scouring pads because

they can damage the ninish of the doors.

Connect the Electrical Components

AC Operation 120 volts (132 volts max. - 108 volts min.)

12 volts (15.4 volts max. - 10.5 volts min.)

DC Operation 12 volts (15.4 volts max. - 10.5 volts min.)

This refrigerator operates on these electrical sources. Operation out of these limits may damage the refrigerator’s electrical circuit

parts and will void the warranty.

WARNING

NOTICE

209

Art01850

Art01814

Installation Manual 15

The rear of the refrigerator cooling system has hot surfaces and sharp surfaces that can damage electrical

wiring. Make sure that there is a good clearance between all electrical wiring and the cooling system of the

refrigerator. Position any electrical wiring within the refrigerator enclosure opposite the burner side of the

refrigerator. Do not put any electrical wiring through the roof exhaust vent. Failure to correctly position

electrical wiring can result in electrical shock or re.

Connect the 120 volts AC supply:

Connect the AC power cord(s) only to a grounded three-prong receptacle. Do not remove the round

ground prong from any of the AC power cords. Do not use a two prong adapter or an extension cord with

any of the AC power cords. Operation of the refrigerator without correct ground can cause dangerous

electrical shock or death if you are touching the metal parts of the refrigerator.

Put the AC power cord(s) into a grounded three-prong receptacle:

- Make sure the receptacle is positioned within easy reach of the lower intake vent.

- Make sure the power cord(s) does not touch the burner cover, the ue pipe, or any hot component that could damage the insulation

of the power cord.

Connect the 12 volts DC supply:

As the distance from the vehicle battery to the refrigerator increases, the correct AWG wire size and fuse size also increases. If the

wire size is too small for the distance, a voltage drop occurs. The voltage drop decreases the output of the system heater and causes

poor cooling performance.

1. Determine the min. wire size and the max. fuse size to use:

If you use an incorrect wire size and/or fuse size,

electrical re can result.

- On 2-way models, use a minimum of 18 AWG wire and a maximum 6 Amp

fuse.

2. Install a fuse in DC power supply wires between the battery and the

refrigerator:

- Put fuse as close to the battery as possible.

3. Connect the DC power supply wires (See Art02402):

- Attach a 1/4 inch Quick Connect terminal to each DC power supply wire.

- Push the positive DC power wire onto the power board terminal that is

marked 12VDC [288].

- Push the DC ground wire onto the power board terminal that is marked GND [287].

- Make sure each DC power supply wire is on the correct polarity terminal.

Art02402

287

288

WARNING

Connect the Low Ambient Heater

Connect the low ambient heater wires to the 12 volts DC supply. The black (+) wire of the low ambient heater connects to 12V and the

brown wire connects to 12V ground.

This kit supplies DC voltage to the heater any time the ambient temperature is low enough. Extended storage during

cold weather will drain the vehicle batteries. To prevent battery drain, remove the 3 amp fuse from the low ambient

heater.

NOTICE

Installation Manual 16

This refrigerator operates on propane gas at a pressure of 11 inches Water Column Propane.

The controls operate on 12 volts DC (10.5 volts min. - 15.4 volts max.). Operation out of these limits can damage the refrigerator

electrical circuit parts and will void the warranty.

Connect the propane gas supply system:

Be very careful when working on or near the propane gas system.

- Do not smoke, or use an open ame near the propane gas system.

- Do not use an open ame to examine for leaks.

- Do not connect the refrigerator to the propane gas tank without a pressure regulator between them.

- To avoid a propane gas leak, always use two wrenches to tighten or loosen the propane gas supply line connections.

- Leaking propane gas can ignite or explode and result in dangerous personal injury or death.

Connect the Propane Gas Components

Connect the gas supply line to the refrigerator:

- Make sure that all tubing and ttings obey all local, state, and national codes about size and type.

- Make sure that all exible metal connectors obey the current CAN1-6.10 Standard.

- Make sure that the materials used for the gas supply line obey both the current ANSI A 119.2 (NFPA 1192) and CSA Z240

Standards on Recreational Vehicles. Norcold recommends the use of 3/8 inch copper tubing as the gas supply line and requires a

3/8 inch SAE (UNF 5/8-18) male are tting as the connection to the refrigerator.

- Put the propane gas supply line up through the oor of the enclosure.

- Make sure the hole through the oor is large enough allow clearance for the gas supply line.

- Put a weather resistant seal (grommet, sealant, etc.) around the gas supply line where it goes through the oor to prevent vibration

and abrasion.

- To prevent vibration and abrasion, make sure that the gas supply line is not against anything in the enclosure.

- Attach the gas supply line to the bulkhead tting of the refrigerator.

Examine the propane gas supply line for leaks:

Do not allow the leak detecting solution to touch the electrical components. Many liquids are electrically

conductive and can cause electrical shorts and in some cases, re.

Use a leak detecting solution to examine the gas supply line and all propane gas connections for leaks.

If you use compressed air for the test:

- The pressure of the compressed air at the manual shut o valve of the refrigerator must not be more than 1/2 psig (14 inches Water

Column).

- If the pressure of the compressed air is more than 1/2 psig (14 inches Water Column), remove the gas supply line from the

bulkhead tting of the refrigerator before the test.

- If the pressure of the compressed air is equal to or less than 1/2 psig (14 inches Water Column), close the manual shut o valve of

the refrigerator before the test.

WARNING

Installation Manual 17

Connect the Ice Maker (Optional)

The ice maker maybe assembled to the refrigerators at the factory.

The refrigerator installer must connect a cold water supply line to the solenoid valve at the rear of the refrigerator. The following are

necessary to connect the icemaker:

- 1/4 in. OD copper tubing for the water supply line.

- 1/4 in. OD plastic tubing for the water supply line.

- 1/4 in. shut o valve in the water supply line. This should be easily accessible through the lower intake vent.

Connect the water supply line:

Install a 1/4 in. OD water supply line [43] from the water shut o valve [44] of the vehicle to the solenoid water valve [44] at the rear of

the refrigerator (See Art02491):

A brass compression nut [45], a brass sleeve, a plastic

sleeve [46] , and a brass insert [47] are supplied and

attached to the rear of the refrigerator (See Art01604).

- Put the compression nut and then the sleeve onto the water supply line

[43].

- For copper tubing, use the brass sleeve.

- For plastic tubing, use the plastic sleeve [46].

- For plastic tubing with .040 in. wall thickness, also use the brass insert [47].

- Flush the water supply line until the water is clear.

- Put the tubing into the adapter [48] until it is against the stop of the adapter.

- Tighten the compression nut by hand (hard nger tight).

- Using two wrenches, tighten the compression nut 1 ½ to 2 turns.

- Open the water shut o valve of the vehicle.

- Examine the connections for leaks.

Art 02491

Art01604

NOTICE

Installation Manual 18

Before ignition or start up of the refrigerator:

- Make sure the air ow in the lower intake vent, through the refrigerator coils and condenser, and out the upper exhaust vent is not

blocked or decreased.

- Make sure there are no combustible materials in or around the refrigerator.

Ignition and start up:

If the gas does not ignite within 30 seconds, the gas valve of the refrigerator will automatically close, the igniter will stop

sparking, an audible alarm will sound, and the fault codes “no” “FL” will ash on the LCD [280]. To reset the controls,

press and hold the POWER ON/OFF button [30] for 1 second to turn the refrigerator o and then press it again to

restart the refrigerator (See Art02492).

If the gas does not ignite after several attempts, refer to the “Fault Codes” section of this manual.

Modes of Operation:

1. Push and release the POWER ON/OFF button [30]

2. Select the mode of operation.

- Push and hold the MODE button [31] to scroll through the available operation modes of the refrigerator, one after the other.

- When the desired mode indicator comes on in the LCD, release the MODE button.

- Or push and release the MODE button again and again to change the available operation modes of the refrigerator, one at a time.

- As you change the mode, the applicable mode indicator will come on.

Ignition and Start Up

NOTICE

set

ART 02492

30 31

280

278

Installation Manual 19

- On 2-way models, the mode indicators are (See Art02493):

- Auto mode AC electric [281]

- Auto mode gas [282]

- Manual mode AC electric [283]

- Manual mode gas [284]

3. Select the temperature setting:

- Push and hold the TEMPERATURE SET button [32] to

scroll through the temperature settings, one after the other

(See Art02492).

- Or push and release the TEMPERATURE SET button

again and again to change the temperature settings, one

at a time.

- The temperature settings [278] come on as numbers in the

LCD.

- Select one of nine (9) temperature settings:

- One (1) is the warmest temperature setting.

- Nine (9) is the coldest temperature setting.

Do a test of the gas safety valve:

1. Start up the refrigerator in the manual mode operation.

2. Open the lower intake vent.

3. Remove one wire from the solenoid of the gas safety valve at the rear of the refrigerator.

4. Within 30 seconds, the ame should extinguish. This means that the gas safety valve is operating correctly.

5. Put the wire back on the solenoid of the gas safety valve.

6. Close the lower intake vent.

Shut down - all models:

To shut down the refrigerator, push and hold the ON/OFF button for one second.

ART 02493

set

284

282

281

283

Installation Manual 20

Fault Codes

“dr”

Audible alarm also.

“no” “FL”

Audible alarm also.

“no” “AC”

Audible alarm also.

“Lo” “dc”

Audible alarm also.

“Sr”

Audible alarm also.

Temperature setting ash-

es when TEMP SET or

MODE button is pushed.

“AC” “rE”

Audible alarm also.

“AC” “HE”

Audible alarm also.

“oP” “LI”

Audible alarm also.

“FL” “- -”

Audible alarm also.

Fault Code Meaning

The door was open for more

than 2 minutes.

The burner did not ignite or

re-ignite.

AC voltage is not available to

the refrigerator.

The DC voltage to the

refrigerator is low.

The DC voltage to the

refrigerator is low.

This is a fault within the

refrigerator controls.

The refrigerator is operating on

the Backup Operating System.

This is a fault within the

refrigerator controls.

This is problem related to the

AC heater.

A temperature limit switch is

open.

A ame is present at the burner

when there should be none.

Corrective Actions

Close the door.

Check:

- That the valve of the propane gas tank(s) is open.

- That the propane gas is at the correct pressure.

- That the manual shut o valve of the refrigerator is open.

- That there is no air in the propane gas supply line. See

“Removing air from the propane gas supply lines” section of

the Owner’s Manual.

- See your dealer or authorized Norcold Service Center.

Check:

- That the refrigerator is plugged into a serviceable outlet.

- That the fuse or circuit breaker or the vehicle is intact.

- That the vehicle generator is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the battery charging equipment of the vehicle is

operational.

- That the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the battery charging equipment of the vehicle is

operational.

- That the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Turn the refrigerator power OFF and then back on to reset.

If the Fault Code continues, see your dealer or authorized

Norcold Service Center.