GE GTS18ABRRWW Le manuel du propriétaire

Marque: GE

Modèle: GTS18ABRRWW

Catégorie: Congélateurs

Taper: Le manuel du propriétaire

Refrigerators
Top-Freezer
www.GEAppliances.com
162D3905P011     49-60250-1    11-03 JR
Safety Instructions
Adapter Plugs  . . . . . . . . . . . . . . . . 6
Connecting Electricity  . . . . . . . . . 4
Extension Cords  . . . . . . . . . . . . . . 5
Proper Disposal  . . . . . . . . . . . . . . 2
Safety Precautions  . . . . . . . . . . . . 3
Operating Instructions
Automatic Icemaker  . . . . . . . . . .11
Care and Cleaning  . . . . . . . . 12, 13
Shelves . . . . . . . . . . . . . . . . . . . .8, 9
Storage Drawers . . . . . . . . . . . .9, 10
Temperature Controls . . . . . . . . . .7
Installation Instructions
Preparing to Install 
the Refrigerator  . . . . . . . . . . . . . 14
Reversing the Door Swing  . . 19–24
Water Line Installation  . . . . . 15–19
Troubleshooting Tips
Before You Call For Service . .26, 27
Normal Operating Sounds  . . . . .25
Customer Service
Consumer Support . . . . Back Cover
Product Registration . . . . . . . 29, 30
Warranty for 
Canadian Customers  . . . . . . . . . 28
Warranty for U.S. Customers  . . . 31
Write the model and serial 
numbers here:
Model # __________________
Serial # __________________
You can find them on a label on 
the upper left side of the fresh food
compartment.
Models 
15, 16, 17, 18
Owner’s Manual and
Installation Instructions

COMMENT VOUS DÉBARRASSER

CONVENABLEMENT DE VOTRE ANCIEN RÉFRIGÉRATEUR

Les enfants pris au piège ou morts d’asphyxie

sont toujours d’actualité. Les réfrigérateurs

abandonnés sont toujours aussi dangereux,

même si on n’attend que «quelques jours»

pour s’en débarrasser. Si vous ne gardez pas

votre ancien réfrigérateur, veuillez suivre les

directives ci-dessous afin de prévenir les accidents.

Avant de vous débarrasser de votre ancien

réfrigérateur ou congélateur :

■ Démontez les portes.

■ Laissez les clayettes en place afin d’empêcher

les enfants de grimper à l’intérieur.

Réfrigérants

Tous les appareils de réfrigération contiennent

des réfrigérants qui, conformément aux lois

fédérales, doivent être enlevés avant toute

élimination de l’appareil. Si vous vous

débarrassez de vieux appareils de réfrigération,

vérifiez, auprès de la société qui s’occupe de

leur élimination, ce que vous devez faire.

DANGER! RISQUES POUR LES ENFANTS

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they

will sit for “just a few days.” If you are getting

rid of your old refrigerator, please follow the

instructions below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the

company handling the disposal about what

to do.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING. www.GEAppliances.com

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Turning the control to the 0 position does

not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

MESURES DE SÉCURITÉ IMPORTANTES.

LISEZ D’ABORD TOUTES LES DIRECTIVES.

AVERTISSEMENT!

N’utilisez cet électroménager que pour l’usage auquel il est destiné, comme expliqué dans le

présent manuel.

MESURES DE SÉCURITÉ

Lorsque vous utilisez un appareil électrique, observez toujours les mesures de sécurité de base,

y compris les suivantes.

■ Installez le réfrigérateur conformément aux

directives d’installation avant de l’utiliser.

■ Ne laissez pas les enfants grimper, s’asseoir,

se tenir debout ni se pendre aux clayettes du

réfrigérateur. Ils pourraient endommager le

réfrigérateur et se blesser gravement.

■ N’entreposez et n’utilisez pas d’essence ou

autres vapeurs et liquides inflammables à

proximité de cet appareil ou de tout autre

appareil électroménager.

■ Éloignez les doigts des parties du réfrigérateur

où l’on peut facilement se pincer : les espaces

entre les portes et entre les portes et les placards

sont toujours étroits. Soyez prudent lorsque

vous fermez les portes de l’appareil en présence

des enfants.

■ Si votre réfrigérateur est doté d’une machine à

glaçons automatique évitez le contact avec les

pièces mobiles du mécanisme éjecteur, ou avec

l’élément chauffant qui libère les glaçons.

Ne posez pas les doigts ou les mains sur le

mécanisme de la machine à glaçons pendant

que le réfrigérateur est branché.

■ Ne touchez pas les surfaces froides du congélateur

si vous avez les mains humides ou mouillées : la

peau risque d’adhérer à ces surfaces très froides.

■ Débranchez votre réfrigérateur avant de le

nettoyer ou de le réparer.

REMARQUE : Nous vous recommandons vivement de

confier toute réparation à un technicien qualifié.

■ Lorsque vous réglez la commande sur 0 (éteint),

l’alimentation électrique de l’ampoule n’est pas

coupée.

■ Ne recongelez pas les aliments surgelés qui ont

complètement dégelé.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

MESURES DE SÉCURITÉ IMPORTANTES.

LISEZ D’ABORD TOUTES LES DIRECTIVES.

AVERTISSEMENT!

RACCORDEMENT ÉLECTRIQUE

Ne coupez ni retirez en aucun cas la troisième broche (mise à la terre) de la fiche du cordon

d’alimentation. Pour votre sécurité, cet appareil doit être correctement mis à la terre.

Le cordon d’alimentation de cet appareil est

muni d’une fiche à 3 broches (mise à la terre)

qui se branche dans une prise murale ordinaire

à 3 alvéoles (mise à la terre) pour réduire au

minimum les risques de chocs électriques.

Faites examiner la prise de courant et le circuit

par un électricien qualifié pour vous assurer que

la prise est correctement mise à la terre.

Si la prise murale est du type standard à 2 alvéoles,

il vous incombe de la faire remplacer par une

prise à 3 alvéoles correctement mise à la terre.

Le réfrigérateur doit toujours être branché dans

sa propre prise de courant, dont la tension

nominale est identique à celle indiquée sur la

plaque signalétique.

Cette précaution est recommandée pour garantir

un rendement optimum et éviter une surcharge des

circuits électriques de la résidence, ce qui pourrait

créer un risque d’incendie par surchauffe des fils.

Ne débranchez jamais le réfrigérateur en tirant

sur le cordon d’alimentation. Saisissez fermement

la fiche du cordon et tirez droit pour la retirer

de la prise.

Réparez ou remplacez immédiatement tout cordon

effiloché ou endommagé. N’utilisez pas un cordon

fendillé ou présentant des signes d’usure.

Lorsque vous déplacez votre réfrigérateur du mur,

faites attention de ne pas le faire rouler sur le cordon

d’alimentation afin de ne pas l’endommager.

Consumer Support

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

CORDONS PROLONGATEURS

Nous vous recommandons fortement de ne pas utiliser de cordons prolongateurs à cause des risques

potentiels qu’ils présentent dans certaines conditions.

Toutefois si vous décidez d’utiliser tout de même un cordon prolongateur, il est absolument nécessaire

qu’il s’agisse d’un cordon à 3 fils avec mise à la terre pour appareils électroménagers homologué UL (aux

États-Unis) ou certifié CSA (au Canada), pourvu d’une fiche et d’une prise mises à la terre de 15 ampères

(minimum) et de 120 volts.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend

against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING. www.GEAppliances.com

Consumer Support

FICHE D’ADAPTATION (Fiches d’adaptation non permises au Canada)

Nous vous recommandons fortement de ne pas utiliser une fiche d’adaptation à cause des risques

potentiels qu’elle présente dans certaines circonstances.

Toutefois, si vous décidez d’utiliser tout de même

une fiche d’adaptation, vous pouvez effectuer un

raccordement temporaire, si les codes locaux le

permettent, dans une prise de courant à 2 alvéoles

adéquatement mise à la terre en utilisant une fiche

d’adaptation homologuée UL, en vente dans la

plupart des quincailleries.

La fente la plus longue de la fiche doit être alignée

avec la fente la plus longue de la prise murale afin

d’assurer la polarité appropriée pour le

branchement du cordon d’alimentation.

Lorsque vous débranchez le cordon d’alimentation

de la fiche d’adaptation, saisissez toujours la fiche

d’une main pendant que vous tirez sur la fiche

du cordon d’alimentation de l’autre. Sinon,

la borne de mise à la terre de la fiche d’adaptation

risque de casser avec le temps.

Si la borne de mise à la terre de la fiche casse,

N’UTILISEZ PAS l’appareil tant qu’une mise à la terre

adéquate n’aura pas été rétablie.

Le fait de fixer la borne de mise à la terre de la fiche

d’adaptation à la plaque de la prise de courant n’assure pas

automatiquement la mise à la terre de l’appareil. Il faut que la

vis soit en métal, non isolée, et que la prise de courant soit

mise à la terre par l’entremise du câblage de la résidence.

Faites vérifier le circuit par un électricien qualifié pour vous

assurer que la prise est adéquatement mise à la terre.

VEUILLEZ LIRE ET SUIVRE ATTENTIVEMENT CES MESURES DE SÉCURITÉ.

CONSERVEZ CES DIRECTIVES

USE OF ADAPTER PLUGS

(Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet cover

screw does not ground the appliance unless the cover screw

is metal, and not insulated, and the wall outlet is grounded

through the house wiring. You should have the circuit checked

by a qualified electrician to make sure the outlet is properly

grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

MESURES DE SÉCURITÉ IMPORTANTES.

LISEZ D’ABORD TOUTES LES DIRECTIVES.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the temperature control dial. www.GEAppliances.com

Control Settings

Temperature Control Dial

The temperature control dial has nine settings plus 0. 1 is the warmest. 9 is the coldest.

At first, set the dial at 5.

After using the refrigerator, adjust the dial if necessary.

Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting

that’s best suited to your needs.

Allow 24 hours for the refrigerator to get cold.

Turning the dial to 0 stops cooling in both compartments–fresh food and freezer. It does not shut off power

to the refrigerator.

About the fresh food compartment shelves.

Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.

Full-Width Shelves

Some models have a steel wire sliding

shelf, a stationary tempered glass shelf or

two steel wire stationary shelves. These

shelves can be moved to another place

in the fresh food compartment.

The full-width sliding shelf has stop-locks.

When placed correctly on the shelf

supports, the shelf will stop before coming

completely out of the refrigerator and will

not tilt when you place food on it or

remove food from it.

To remove the full-width shelves, lift the

rear of the shelf and pull forward.

To remove a full-width shelf when the fresh

food compartment door cannot be opened

fully, lift the rear of the shelf, pull

forward and down, tilt the shelf and

take it out.

Half-Width Shelves

One end of the shelf rests on a molded

side-wall support; a bracket on the other

end hooks into a track on the rear

cabinet wall.

To remove, lift the shelf up at front, then

off the support and out of the track.

To replace, select desired shelf height.

With shelf front raised slightly, hook the

bracket’s top lug into the track, then

lower the shelf onto the support.

NOTE: The shelf to the right of the track is

designed to hook into the right-hand slot;

the shelf to the left is designed to hook

into the left-hand slot.

Lift up and out

Tilt up

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Spillproof Shelves (on some models)

Spillproof shelves have special edges

to help prevent spills from dripping

to lower shelves. To remove or replace

the shelves, see the above instructions.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the freezer compartment shelves. www.GEAppliances.com

Some models have an ice-tray shelf and some have a full-width step shelf.

Ice-Tray Shelf

To remove the ice-tray shelf, lift the left

side of the shelf off its supports, then

pull the shelf to the left to free it of the

plug supports. Pull the shelf to the right

to free the pins from the holes in the

cabinet wall.

Step Shelf

To remove the step shelf:

Lift left side of shelf slightly.

Move shelf to the left to free its right

ends from holes in the cabinet wall.

Lower right side of shelf, move shelf to

the right and take it out.

To replace the step shelf:

With shelf tilted as shown, fit left ends

of shelf into holes in cabinet wall.

Lift left side of shelf slightly, swing shelf

up, fit right ends of shelf into holes in

cabinet wall, and lower shelf into place.

Plug Supports

About the storage drawers.

Not all features are on all models.

Fruit and Vegetable Drawers

Excess water that may accumulate in the

bottom of the drawers should be emptied

and the drawers wiped dry.

Snacks Drawer

The snacks drawer can be moved to the

most useful location for your family’s

needs.

About storage drawer and cover removal.

Not all features are on all models.

Drawer and Cover Removal

Drawers can be removed easily by grasping

the sides and lifting up slightly while

pulling drawers past the stop location.

Full-Width Drawer with Plastic Cover

To remove the cover, lift it off its supports,

pull it forward, tilt it and take it out.

Twin Drawers with Glass Cover

To remove:

Remove the drawers.

Reach in, push the front of glass

cover up, and at the same time,

pull it forward as far as it will come.

Tilt it and take it out. Avoid cleaning the

cold glass cover with hot water because

the extreme temperature difference may

cause it to break.

Remove the drawer frame. (Always

remove the glass cover before you

take out the drawer frame.)

Lift the frame off the supports at each

side and back, pull it forward, tilt it and

take it out.

To replace:

Lower the frame until it rests on the

supports at each side and back.

Replace the glass cover, pushing its

rear edge firmly into the rear frame

channel and gently lowering the front

into place.

Replace the drawers.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Adjustable Humidity Drawer (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the automatic icemaker. www.GEAppliances.com

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker Accessory Kit

If your refrigerator did not already come

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for your

model.

Automatic Icemaker (on some models)

The icemaker will produce seven cubes

per cycle–approximately 100-130 cubes

in a 24-hour period, depending on

freezer compartment temperature,

room temperature, number of door

openings and other use conditions.

There are two types of icemakers: power

switch models and feeler arm models.

If the refrigerator is operated before

the water connection is made to the

icemaker, set the power switch to O (off)

or move the feeler arm to the STOP (up)

position.

When the refrigerator has been

connected to the water supply, set the

power switch to the I (on) position or move

the feeler arm to the ON (down) position.

On power switch models, the green light

will come on.

You will hear a buzzing sound each time

the icemaker fills with water.

The icemaker will fill with water when

it cools to 15°F. A newly-installed

refrigerator may take 12 to 24 hours

to begin making ice cubes.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the

sweep of the feeler arm.

When the bin fills to the level of the

feeler arm, the icemaker will stop

producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to O (off) and remove the cubes. Set

the power switch to I (on) to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle

multiple times when making one batch of ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Power switch model

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim (on some

models). Clean with a cloth dampened

with soapy water. Dry with a soft cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with

a commercially available stainless steel

cleaner. Do not use appliance wax or

polish on the stainless steel.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the fresh food and

freezer compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess

moisture out of sponge or cloth when

cleaning around switches, lights or

controls.

Use warm water and baking soda solution–

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and

wipe dry.

After cleaning the door gaskets, apply a

thin layer of petroleum jelly to the door

gaskets at the hinge side. This helps keep

the gaskets from sticking and bending

out of shape.

Avoid cleaning cold glass shelves (on some

models) with hot water because the extreme

temperature difference may cause them to

break. Handle glass shelves carefully. Bumping

tempered glass can cause it to shatter.

Éviter de nettoyer les tablettes en verre froides

(sur certains modèles) à l’eau chaude parce que

l’écart de température extrême risque de les

craquer. Manipuler les tablettes en verre avec

précaution. Le verre trempé soumis à un choc

risque de se fracasser.

Do not wash any plastic refrigerator parts in

the dishwasher.

Condenser

There is no need for routine condenser

cleaning in normal home operating

environments. However, in environments

that may be particularly dusty or greasy,

the condenser should be cleaned

periodically for efficient refrigerator

operation.

To clean the condenser, turn the

temperature control dial to 0. Sweep

away or vacuum up dust.

For best results, use a brush specially

designed for this purpose. It is available

at most appliance parts stores.

Cleaning the condenser coils.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Turn the leveling legs at each front corner

of the refrigerator counterclockwise until

the rollers support the refrigerator. Pull the

refrigerator straight out and return it to

position by pushing it straight in. Moving

the refrigerator in a side direction may

result in damage to the floor covering or

refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

En poussant le réfrigérateur en place, veiller à ne

pas le faire rouler sur le cordon d’alimentation ou

la canalisation d’eau de la machine à glaçons

(sur certains modèles).

After rolling the refrigerator back into

place, turn the legs clockwise until the

legs again bear the weight of the

refrigerator.

Light Bulb Replacement

To replace a burned-out bulb, unplug

the refrigerator from its electrical outlet,

unscrew the bulb when cool and replace

it with an appliance bulb of the same or

lower wattage.

Turning the control to the 0 position does not

remove power to the light circuit.

Preparing for Vacation

For long vacations or absences, remove

food and unplug the refrigerator. Move

the temperature control dial to the 0

position, and clean the interior with a

baking soda solution of one tablespoon

(15 ml) of baking soda to one quart

(1 liter) of water. Leave the doors open.

Set the icemaker power switch to the

O (off) position or move the feeler arm to

the STOP (up) position (depending on

model) and shut off the water supply to

the refrigerator.

If the temperature can drop below

freezing, have a qualified servicer drain

the water supply system (on some

models) to prevent serious property

damage due to flooding.

Preparing to Move

Secure all loose items such as grille,

shelves and drawers by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright

position during moving.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes

Reversing the Door Swing

1 hour

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

Installation

Refrigerator

Instructions

Models 15, 16, 17, 18

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 3/4″ (19 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

CLEARANCES

Leveling legs near each front corner of the refrigerator

are adjustable. They firmly position the refrigerator

and prevent it from moving when the doors are

opened. Leveling legs should be set so the front of the

refrigerator is raised just enough that the doors close

easily when opened about halfway.

Turn the leveling legs clockwise to raise the

refrigerator, counterclockwise to lower it.

Rollers next to the leveling legs allow you to move the

refrigerator away from the wall for cleaning.

Turn the legs counterclockwise until the weight of the

refrigerator is transferred from them to the rollers.

After rolling the refrigerator back into place, turn the

legs clockwise until the legs again bear the weight of

the refrigerator.

ROLLERS AND LEVELING LEGS

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A water supply kit

(containing copper tubing, shutoff valve, fittings and

instructions) is available at extra cost from your dealer,

by visiting our Website at www.GEAppliances.com (in

Canada at www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada 1.888.261.3055).

WATER SUPPLY TO THE ICEMAKER

(on some models)

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

In Canada, call 1.800.361.3400

or Visit our Website at: www.geappliances.ca

WHAT YOU WILL NEED

• Copper or GE SmartConnect

™

Refrigerator Tubing

kit,1/4″ outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both

ends of the tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8′

(2.4 m). Be sure there is sufficient extra tubing

(about 8′ [2.4 m] coiled into 3 turns of about 10″

[25 cm] diameter) to allow the refrigerator to move

out from the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are

available in the following lengths:

2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and

cause water damage to your home.

INSTALLING THE WATER LINE (ON SOME MODELS)

Installation Instructions

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines

are GE SmartConnect

™

Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing

the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is

in the O (off) position (on power switch models) or

the feeler arm is in the STOP (up) position (on feeler

arm models).

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

WHAT YOU WILL NEED (CONT.)

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing

to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect

™

Refrigerator

Tubing kit, the necessary fittings are preassembled

to the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression

fitting. Do not cut formed end from GE

SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

DRILL THE HOLE FOR THE VALVE

Drill a 1/4″ hole in the water pipe (even if using

a self-piercing valve) using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily

accessible. It is best to connect into the side of

a vertical water pipe. When it is necessary to

connect into a horizontal water pipe, make the

connection to the top or side, rather than at the

bottom, to avoid drawing off any sediment from

the water pipe.

Installation Instructions

Install the shutoff valve on the nearest frequently used

drinking water line.

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear

the line of water.

INSTALLING THE WATER LINE (CONT.)

FLUSH OUT THE TUBING

Turn the main water supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the tubing.

CONNECT THE TUBING

TO THE VALVE

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the

valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Installation Instructions

Saddle-Type

Shutoff Valve

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

Washer

Inlet End

Pipe Clamp

Clamp Screw

ROUTE THE TUBING

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8 feet [244 cm] coiled into 3 turns of about

10″ [25 cm] diameter) to allow the refrigerator to

move out from the wall after installation.

Installation Instructions

CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged

into the wall outlet.

• We recommend installing a water filter if your

water supply has sand or particles that could clog

the screen of the refrigerator’s water valve. Install

it in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing kit,

you will need an additional tube (WX08X10002)

to connect the filter. Do not cut plastic tube to

install filter.

Remove the access cover.

Remove the plastic flexible cap from the water

valve (refrigerator connection).

Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown. On GE

SmartConnect

™

Refrigerator Tubing kit,

the nuts are already assembled to the tubing.

Insert the end of the tubing into the water valve

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then

tighten one additional turn with a wrench.

Overtightening may cause leaks.

TURN THE WATER ON AT THE

SHUTOFF VALVE

Tighten any connections that leak.

Reattach the access cover.

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

Fasten the tubing into the clamp provided to

hold it in a vertical position. You may need to

pry open the clamp.

Reattach the access cover.

Tubing Clamp

1/4″ Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

1/4″ Copper

Tubing

INSTALLING THE WATER LINE (CONT.)

Installation Instructions

REVERSING THE DOOR SWING

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using

them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the

cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

the right side to the left side—if you ever want to change

the hinges back to the right side, follow these same

instructions and reverse all references to left and right.

IMPORTANT NOTES

Phillips screwdriver

TOOLS REQUIRED

Masking tape

T20 or T25 Torxdriver,

(Needed for some models)

5/16″ hex-head

socket driver

5/16″ open-end

wrench

Putty knife or thin-

blade screwdriver

PLUG IN THE REFRIGERATOR

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

On power switch models, set the icemaker power

switch to the l (on) position. On feeler arm models,

move the feeler arm to the ON (down) position. The

icemaker will not begin to operate until it reaches

its operating temperature of 15°F (–9°C) or below.

It will then begin operation automatically.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

START THE ICEMAKER

Power

switch

Power switch model

Feeler Arm in the

STOP (up) position

Feeler Arm in

the ON (down) position

Feeler arm model

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

2.1 Tape the door shut with masking tape.

REMOVE THE FREEZER DOOR

2.2 With a 5/16″ hex-head socket driver, remove the

screws that hold the top hinge to the cabinet.

2.3 Lift the hinge (and the shim glued to it) straight

up to free the hinge pin from the socket in

the top of the door and set it aside, along with

its screws.

Top Hinge

2.6 Transfer the 2 screws from the opposite side of

the cabinet to the screw holes vacated by the

top hinge removal.

2.5 Set the door on a non-scratching surface with

the outside up.

2.4 Remove the tape and tilt the door away from the

cabinet. Lift it off the center hinge pin.

1.1 Unplug the refrigerator from its electrical

outlet.

BEFORE YOU START

1.2 Empty all door shelves, including the dairy

compartment.

CAUTION: Do not let either door drop to the

floor. To do so could damage the door stop.

La page charge ...

GE GTS18ABRRWW Le manuel du propriétaire

Marque: GE

Modèle: GTS18ABRRWW

Catégorie: Congélateurs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE GTS18ABRRWW Owner's manual

GE GTS18ABRRWW Le manuel du propriétaire

GE GTS18ABRRWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents