Bauknecht EXCELLENCE 720P Mode d'emploi

Marque: Bauknecht

Modèle: EXCELLENCE 720P

Catégorie: Machines à laver

Taper: Mode d'emploi

EN 1

INTENDED USE

This washing machine is exclusively destined to

treat machine washable laundry in quantities

which are usual for private households.

• Observe the instructions given in these

Instructions for Use, the Installation Guide and

the Programme Chart when using the washing

machine.

• Keep these Instructions for Use, the Programme

Chart and the Installation Guide; if you pass on

the washing machine to another person, also

give him/her Instructions for Use, Programme

Chart and Installation Guide.

SAFETY AND GENERAL RECOMMENDATIONS

1. Safety instructions

• The washing machine is

appropriate for indoor use

only.

• Do not store flammable fluids

near the appliance.

• The washing machine can be

operated by children from the

age of 8 years up, as well as by

people with reduced physical,

sensory or mental capabilities

or lack of experience and

knowledge, provided they are

supervised or instructed

regarding the safe use of the

washing machine and they

understand the dangers

resulting from the use.

Children must not play with

the washing machine. Care

and maintenance works on

the washing machine must

not be carried out by children

without being supervised.

• Do not operate the washing

machine at temperatures

below 5 °C.

• If you want to place a dryer on

top of your washing machine,

first contact our After-Sales

Service or your specialist

dealer to verify if this is

possible. This is only admitted

if the dryer is fixed on the

washing machine by using an

appropriate stacking kit

available through our After-

Sales Service or your specialist

dealer.

• After installation, access

to the mains plug or to

disconnection from mains

supply must be ensured at

all times via a double-pole

switch.

• Turn off the tap when not in

use.

• Before any cleaning and

maintenance switch off the

machine or disconnect it from

the mains.

• Never open the door forcibly

or use it as a step.

• If necessary, the power cable

may be replaced with an

identical one obtained from

our After-Sales Service. The

power cable must only be

replaced by a qualified

technician or by our After-

Sales Service, to avoid

dangers.

EN 2

2.Packaging

• The packaging material is entirely recyclable,

and marked with the recycling symbol .

Adhere to current local regulations when

disposing of packaging material.

3.Disposing of packaging and scrapping

old washing machines

• The washing machine is built from reusable

materials. It must be disposed of in compliance

with current local waste disposal regulations.

• Before scrapping, remove all detergent

residues and cut off the power cable so that the

washing machine is made unusable.

• This appliance is marked according to the

European directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly,

you will help prevent potential negative

consequences for the environment and human

health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or on the

documents accompanying the product, indicates

that this appliance may not be treated as

household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment.

Disposal must be carried out in accordance

with local environmental regulations for waste

disposal.

For more detailed information about

treatment, recovery and recycling of this

product, please contact your local city office,

your household waste disposal service or the

shop where you purchased the product.

4.Frost

Do not place the washing machine in a room prone

to frost. If you must, make sure that the washing

machine is completely drained after each wash:

• Remove inlet hose(s) from water tap and let the

water flow out completely.

• Remove drain hose from siphon or handwash

basin and let the water flow out completely.

• Empty residual water inside the machine by

following the instructions in the chapter

“Draining Residual Water”; tilt the appliance

forward with two persons to let the rest water

flow out completely.

5.EC Declaration of Conformity

• The appliance conforms to the following

European Standards:

2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility

Directive

The Manufacturer is not liable for any damage to

laundry resulting from inadequate or incorrect

fabric care instructions which have been provided

with the garment or article.

EN 3

BEFORE USING THE WASHING MACHINE

1.Removing the packaging and inspection

• After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use

the washing machine. Contact After-Sales

Service or your local retailer.

• Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children,

as they are potentially dangerous.

• If the appliance was exposed to the cold prior to

delivery, keep it at room temperature for a few

hours before operating.

2.Remove the transport bolts

• The washing machine is fitted with transport

bolts to avoid any possible damage to the

interior during transport. Before using the

machine, it is imperative that the transport

bolts are removed.

• After their removal, cover the openings with

the 4 enclosed plastic caps.

3.Install the washing machine

• Remove the protective film from the control

panel (if available on your model).

• Move the appliance without lifting it by the

worktop.

• Install the appliance on a solid and level floor

surface, preferably in a corner of the room.

• Make sure that all four feet are stable and resting

on the floor and then check that the washing

machine is perfectly level (use a spirit level).

• In case of wooden or so-called “floating floors”

(for instance certain parquet or laminate floors),

place the appliance on a sheet of plywood at

least 60 x 60 cm wide/deep and at least 3 cm

thick which is secured to the floor.

• Make sure that the ventilation openings in the

base of your washing machine (if available on

your model) are not obstructed by a carpet or

other material.

4.Water inlet

• Connect the water inlet hose(s) to the drinking

water supply in accordance with the

regulations of your local water company.

• For models with one inlet valve: cold water

• For models with two inlet valves: cold AND hot

water, or cold water only (see separate

Installation Guide).

• Water tap: 3/4” threaded hose

connector

• Water pressure

(flow pressure): 100-1000 kPa (1-10 bar).

• Use only new hoses to connect the washing

machine to the water supply. Used hoses must

not be used and should be discarded.

• For models with hot fill: the hot water inlet

temperature must not exceed 60 °C.

5.Drain

• Connect the drain hose to the siphon or any

other outlet for drain water (see separate

Installation Guide).

• If the washing machine is connected to an

integrated drainage system, ensure the latter is

equipped with a vent to avoid simultaneous

loading and draining of water (siphoning effect).

6.Electrical connection

• Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and current

standard safety regulations.

• Data regarding voltage, power consumption

and protection requirements is given on the

inside of the door.

• The appliance must be connected to the mains by

means of a socket with an earth connection in

accordance with current regulations. The

washing machine must be earthed by law. The

manufacturer declines all liability for damage to

property or injury to persons or animals due to

non-compliance with the directions given above.

• Do not use extension leads or multiple sockets.

• Before any maintenance on the washing

machine disconnect it from the mains supply.

• Do not operate the washing machine if it has

been damaged during transport. Inform the

After-Sales Service.

• Mains cable replacement is only to be carried

out by After-Sales Service.

• When using a residual current circuit breaker

(RCCB), only use a model marked with .

EN 4

DESCRIPTION OF THE WASHING MACHINE

DOOR

BEFORE THE FIRST WASH CYCLE

1. Worktop

2. Control panel

3. Detergent dispenser

4. Service plate (inside the door)

5. Door

6. Pump access with filter and emergency drain hose (if available) behind the plinth

7. Adjustable feet

To open the door, hold the door handle and pull the door. Close the door by pressing it without

excessive force until it clicks shut.

To remove any residual water used in testing by the manufacturer, we recommend that you carry out

a short wash cycle without laundry.

1. Open the tap.

2. Close the door.

3. Add a small amount of detergent (maximum 1/3 of the quantity the detergent manufacturer

recommends for lightly soiled laundry) to the main wash chamber of the detergent dispenser.

4. Select and start programme “Synthetics” at 60 °C (see separate programme chart).

Depending on the model:

EN 5

PREPARATION OF THE WASHING

1.Sort the laundry according to...

• Type of fabric / care label symbol

Cottons, mixed fibres, easy care/synthetics,

wool, handwash items.

•Colour

Separate coloured and white items. Wash new

coloured articles separately.

•Size

Wash items of different sizes in the same load to

improve washing efficiency and distribution in

the drum.

• Delicates

Wash small items (e.g. nylon stockings, belts

etc.) and items with hooks (e.g. bras) in a cloth

bag or pillow case with zip. Always remove

curtain rings or wash curtains with the rings

inside a cotton bag.

2.Empty all pockets

Coins, safety pins etc. can damage your laundry

as well as the appliance drum and tub.

3.Fasteners

Close zips and fasten buttons or hooks; loose

belts or ribbons should be tied together.

Stain removal

• Blood, milk, eggs etc. are generally removed by

the automatic enzyme phase of the programme.

• To remove red wine, coffee, tea, grass and fruit

stains etc. add a stain remover to the main wash

chamber of the detergent dispenser.

• Pre-treat heavily-soiled areas with stain

remover if necessary.

Dyeing and bleaching

• Only use dyes and bleaches that are suitable for

washing machines.

• Follow the Manufacturer’s instructions.

• Plastic and rubber parts of the washing

machine can be stained by dyes or bleaches.

Loading the laundry

1.Open the door.

2.Load the articles one at a time loosely into the

drum, without overfilling. Observe the load

sizes given in the programme chart.

Note: overloading the machine will result in

unsatisfactory washing results and creased

laundry.

3.Close the door. Take care that no laundry gets

stuck between door and door seal.

DETERGENTS AND ADDITIVES

Keep detergents and additives in a safe,

dry place out of the reach of children.

Do not use any solvents (e.g. turpentine,

benzene); do not machine wash fabrics

that have been treated with solvents or

flammable liquids.

Only use detergents and/or additives that are

specifically produced for domestic washing

machines.

Observe the recommendations on the care

labels of your laundry.

The choice of detergent depends on:

• Type of fabric

• Colour

• Recommended wash temperature

• Degree and type of soiling

For laundry requiring special treatment (e.g. wool

or microfibres), we recommend to use specialized

detergents, additives or pre-treatment available

on the market.

Refer to internet link www.cleanright.eu for more

detailed information.

Do not use liquid detergent for the main wash

when having activated the “Prewash” option.

Do not use liquid detergent when selecting a

later cycle start / cycle end (depending on the

model).

Dosage

Follow the dosage recommendations on the

detergent pack. They depend on:

• Degree and type of soiling

• Size of wash

- full load: follow the detergent manufacturer’s

instructions.

- half load: 3/4 the amount used for a full load.

- minimum load (about 1 kg): 1/2 the amount

used for a full load.

If there is no reference to a certain wash load on

the detergent pack: the detergent manufacturers

usually refer their dosing recommendations to

4.5 kg laundry for heavy duty detergent and

2.5 kg laundry for delicate detergent.

• Water hardness in your area (ask for

information from your water company). Soft

water requires less detergent than hard water.

Laundry type Kind of detergent

White robust laundry

(cold-95°C):

heavy duty detergents

with bleach

White delicate laundry

(cold-40°C):

mild detergents with

bleach and/or optical

brighteners

Light /pastel- shaded

colours (cold-60°C):

detergents with bleach

and/or optical

brighteners

Intensive colours (cold-

60°C):

colour detergents

without bleach/optical

brighteners

Black/dark colours

(cold-60°C):

special detergents for

black/dark laundry

EN 6

Please note:

Too much detergent can result in excess foam formation, which reduces washing efficiency.

If the washing machine detects too much foam, it may prevent spinning, or prolong the programme

duration and increase the water consumption (see also remarks on foam formation in the

“Troubleshooting Guide”).

Insufficient detergent may result in grey laundry and also calcifies the heating system, drum and hoses.

Where to put detergent and additives

The detergent drawer has three chambers (fig. “A”).

Main Wash Chamber

• Detergent for the main wash

• Stain remover

• Water softener

Softener Chamber

• Fabric softener

• Liquid starch

Pour additives only up to the “MAX” mark.

Prewash Chamber

• Detergent for the prewash

• Fabric softener ONLY when using Colours 15° plus (if available)

If you use liquid detergent, close the dispenser right after having

filled in the detergent.

Insert for the Main Wash Chamber (fig. B - only available for

washing machine models with option “Colours 15° plus”):

This insert must be used in the main wash chamber if you activate

option “Colours 15° plus” and you intend to use liquid detergent

for the main wash.

IMPORTANT! This insert is suitable for liquid detergents only and

must not be used for powder detergents.

If you always use liquid detergents for the main wash, you can

leave the insert in the main wash chamber even when the option

“Colours 15° plus” is not activated.

How to use the option “Colours 15° plus” (if available):

If you activate this option, you must

• add the insert to the main wash chamber only if you intend to

use liquid detergent for the main wash (fig. C)

• pour liquid detergent into the insert placed in the main wash

chamber (fig. D). If you use powder detergent, do not use the

insert. Pour powder into the main wash chamber directly.

• pour liquid fabric softener to the prewash chamber (fig. E),

according to the dosing recommendations indicated on the

softener bottle.

• if you want your laundry to be soft, you can of course add liquid

fabric softener to the softener chamber as well

()

EN 7

Using chlorine bleach

• Wash your laundry in the desired programme (Cotton, Synthetics),

adding an appropriate amount of chlorine bleach to the SOFTENER

chamber (close the detergent dispenser carefully).

• Immediately after end of programme, start the “Rinse and Spin”

programme to eliminate any residual bleach smell; if you want,

you can add softener.

Never put both chlorine bleach and softener into the softener

chamber at the same time.

• Prefer to use bleaches on oxygen basis; in this case follow the

instructions of the manufacturer.

Using starch

• Select the “Rinse and Spin” programme and check that the spin

speed is adjusted to not more than 800 rpm.

• Start the programme, pull out the detergent dispenser so that

you can see approximately 3 cm of the softener chamber.

• Pour the starch solution prepared into the softener chamber

while the water is running into the detergent dispenser.

EN 8

DRAINING RESIDUAL WATER/

CLEANING THE FILTER

We recommend that you check and clean the filter

regularly, at least two or three times a year, especially:

• If the “Clean pump” indication lights up.

• If the appliance is not draining properly or if it fails to

perform spin cycles.

If the washing machine stands in a room prone to frost, you

have to drain residual water after each wash to avoid damages.

IMPORTANT: make sure the water has cooled before

draining the appliance.

1. Stop the appliance and unplug it.

2. To open the plinth (depending on the model):

- Push down the tabs right and left (if available) to

release the plinth and remove it (picture “A”).

- Remove the plinth by using the siphon insert of

the detergent dispenser: push downwards one

side of the plinth with your hand, then push the

siphon insert into the gap between plinth and

front panel and pry open the plinth (picture “B”).

3. Place a container near the washing machine.

4. If your washing machine has an emergency drain hose:

- Unclip the emergency drain hose.

If there is no emergency drain hose: place a broad,

flat container beneath the filter (picture “D”). Ignore

steps 5-8 and proceed with 9.

5. Hold the emergency hose’s end into the container

and remove the stopper (picture “C”).

6. Wait until all the water has drained, then refix the

stopper at the hose’s end (picture “E”).

7. Refix the emergency drain hose (if available) to the clip.

8. Lay an absorbable cotton cloth (e.g. a towel) on the

floor in front of the filter.

9. Slowly open the filter by turning it counter-clockwise

(picture “F”); wait until all the water has drained, then

unscrew the filter completely and remove it.

10. Only for draining residual water: tilt the appliance

forwards carefully (a second person must help you)

to allow the water to flow out completely.

11. Only for cleaning the filter: clean the filter and the

filter chamber; check that the pump rotor in the filter

chamber moves freely.

12. Reinsert the filter and screw it in clockwise as far as it

will go.

13. Pour about 1 litre of water into the detergent

dispenser to reactivate the “Eco system”. Check that

the filter is inserted properly and securely and no

water comes out.

14. Reinstall the plinth (picture “G”); if necessary, tilt the

washing machine slightly backwards for doing that

(a second person must help you).

15. Plug in the washing machine. It is now ready for

operation again.

EN 9

CARE AND MAINTENANCE

Appliance exterior and control panel

• Wash down with a soft, damp cloth. Dry with a

soft cloth.

Appliance interior

• After each washing, leave the door open for some

time to allow the inside of the appliance to dry.

• If you never or seldom wash your laundry at

95 °C, we recommend to occasionally run a

95 °C programme without laundry, adding a

small amount of detergent, to keep the interior

of the appliance clean.

Door seal

• Dry the door seal after each washing with an

absorbent cotton cloth; make sure that the

door seal is completely dry before closing the

door of the empty washing machine.

• Check the condition of the door seal

periodically.

Filter

• Check and clean the filter regularly, at least two

or three times a year (see “Draining Residual

Water/Cleaning The Filter”).

Do not use detergents containing solvents, scouring powder, glass or general purpose

cleaners, and flammable fluids. They may harm the plastic surfaces or other parts.

Cleaning the detergent dispenser

1. Pull out the dispenser drawer until it stops. Press with your

finger on the small depression over the “PUSH” marking

(fig. “A”) to release the drawer and pull it out completely.

2. Remove the siphon from the softener chamber by pulling it

upwards (fig. “B”). If available, also remove the insert for liquid

detergent from the main wash chamber and remove the

coloured siphon part (fig. “C”).

3. Wash all the parts under running water.

4. Clean the dispenser compartment with a damp cloth.

5. Refit the siphon in the softener chamber by pushing it down

until it stops; if your washing machine has an insert for liquid

detergent, add the coloured siphon part to the insert again.

Then push the dispenser drawer back into the dispenser

compartment.

Water supply hose(s) (picture D, E or F - depending on

model)

Check regularly for brittleness and cracks. In case of a damage,

replace it by a new hose of the same type, available through our

After-Sales Service or your specialist dealer.

If the inlet hose of your washing machine corresponds with the

model on picture “E”, periodically check the safety valve

inspection window: if it is red, the hose’s waterstop function was

triggered, and the hose must be exchanged by a new one from

our After-Sales Service or your specialist dealer. This model may

have a release lever which must be pressed down while

unscrewing the hose.

If your supply hose has a transparent hose coating (fig. “F”),

periodically check the colour; if it intensifies locally, the hose may

have a leak and should be replaced. Contact our After-Sales

Service team or specialist dealer to obtain a replacement hose.

Cleaning the mesh filter in the water supply hose(s)

1. Close the tap and loosen the inlet hose on the tap.

2. Clean the internal mesh filter and screw the water inlet hose

back onto the tap.

3. Now unscrew the inlet hose on the rear of the washing machine.

4. Pull off the mesh filter from the washing machine connection

with universal pliers and clean it.

5. Refit the mesh filter and screw the inlet hose on again.

6. Turn on the tap and ensure that the connections are

completely water-tight.

Control window

Release lever

EN 10

TROUBLESHOOTING GUIDE

Your washing machine is equipped with various automatic safety functions. These enable faults to be

detected in good time and the safety system can react appropriately. These faults are frequently so minor

that they can be removed within a few minutes.

Problem Causes, Solutions, Tips

Appliance does not start,

no indicators are on

• Plug is not properly inserted in socket.

• Socket or fuse does not function correctly (use a table lamp or similar

appliance to test it).

Appliance does not start

although “Start/Pause”

has been pressed

• Door is not properly closed.

• The “Child lock/Lock buttons” feature has been activated (if

available on your model). To unlock the buttons, push the two buttons

marked with the key symbol simultaneously and hold them at least for

3 seconds. The key symbol on the display disappears and the

programme can be started.

Appliance stops during

the programme, and the

“Start/Pause” indicator

blinks

• “Rinse hold” is activated. Press “Start/Pause” to spin the laundry. For

draining the water without spinning, select “Drain” Programme (if

available) or press the “Reset/Drain” button for at least 3 seconds.

• Programme has been changed - reselect desired programme and press

“Start/Pause”.

• Programme has been interrupted and eventually door has been

opened - close door and restart programme by pressing “Start/Pause”.

• The appliance’s safety system has been activated (see “Failure

indicators” in your programme chart).

• Water tap is not opened or water inlet hose is kinked or blocked (“Water

tap closed” indicator blinks).

Detergent dispenser

contains residues from

detergent and/or

additives

• Water entering is not enough; the mesh filters of the water supply could

be blocked (see “Care And Maintenance”).

Appliance vibrates during

spin cycle

• Transport bolts have not been removed; before using the washing

machine, it is imperative that the transport bolts are removed.

• Appliance is not level / not standing firmly on all four feet (see separate

“Installation Guide”).

“Unbalance during

spinning”

The “Spin/Drain”

indicator in the

programme flow bar

blinks, or the spin speed

on the display blinks, or

the spin speed indicator

blinks after the end of the

programme (depending

on the model).

The laundry is still very

wet.

Unbalance of the laundry load during spinning prevented the spin phase

to avoid damages on the washing machine. This is why the laundry is still

very wet.

Reason for unbalance can be: small laundry loads (consisting of only few

quite big or absorbent items, e.g. towels), or big/heavy laundry items.

• If possible avoid small laundry loads.

• It is highly recommended that you add other laundry items of different

sizes when washing a big or heavy piece of laundry.

If you want to spin the wet laundry, add more laundry items of different

sizes, and subsequently select and start the “Rinse & Spin” programme.

Final spin results are poor • Unbalance during spinning prevented spin phase to protect the

washing machine (see “Unbalance during spinning”).

• Excessive foam formation prevented spinning; select and start “Rinse &

Spin” programme. Avoid excessive detergent dosing (see “Detergents

And Additives”).

• “Spin” button has been set to a low spin speed.

EN 11

Description of failure indicators

The washing machine is at

a standstill for several

minutes in the middle of a

running programme; the

wash programme seems

not to proceed

Normal function of the washing machine used for optimizing the rinse

phase. One reason for such a pause can be that you might have used

too much detergent; the washing machine automatically interrupts the

programme to have the foam reduced. This standstill may be repeated

several times until the foam reduction is sufficient to continue the wash

cycle. If the foam persists, the red “Service” indicator will light up and the

display shows “F18” or “Fod” - refer to the instructions concerning the

“Service” indication on the next pages in this case.

Detergent residues on

laundry after wash

Whitish residues on dark fabrics are caused by insoluble compounds

used in phosphate-free powder detergents.

- avoid overdosing of detergent; use liquid detergent; select “Intensive

Rinse” option if possible; brush out the fabric.

Programme duration is

considerably longer or

shorter as indicated in the

“programme chart” or on

the display (if available)

Normal function of the washing machine to adapt to factors that

can have an effect on the programme duration, like excessive foam

formation, load unbalance due to heavy laundry items, prolonged

heating time resulting from low inlet water temperature etc. Moreover,

the sensing system of the washing machine adapts the programme

duration to the size of the wash load.

Depending on these factors, the duration is recalculated during the

programme and updated if necessary; during such periods, an animation

appears on the display (if available). For small loads, the programme time

indicated in the “programme chart” may be reduced by up to 50%.

Failure

indicator

blinks

Description

Causes

Solutions

“Water tap closed”

Appliance has no or insufficient water supply. The “Start/Pause” light blinks.

Check whether:

• Water tap is fully open and water supply pressure is sufficient.

• Kinks are present in the water inlet hose.

• Mesh filter of water supply hose is blocked (see “Care And Maintenance”.

• The water hose is frozen up.

• The safety valve inspection window of your water supply hose is red (provided

your appliance has a water supply hose as shown on picture “D” - see previous

chapter “Care And Maintenance”); replace the hose by a new one available

through our After-Sales Service or your specialist dealer.

After problem has been removed, restart programme by pressing “Start/Pause”.

If the fault occurs again, contact our After-Sales Service (see next chapter).

“Clean pump”

Waste water is not pumped out. The appliance stops in the corresponding

programme step; unplug it and check whether:

• Kinks are present in the drain hose, or the hose is blocked for another reason.

• Filter or pump is blocked (see chapter “Draining Residual Water/Cleaning The

Filter”; make sure the water has cooled before draining the appliance).

• The drain hose is frozen up.

After problem has been removed, push the “Reset” button for at least 3 seconds;

afterwards restart the desired programme. If the fault occurs again, contact our

After-Sales-Service (see next chapter).

Problem Causes, Solutions, Tips

EN 12

If any of the faults described above persist, unplug the appliance, turn off the water tap

and contact our After-Sales Service (see next chapter).

Failure

indicator

blinks

Indication

on display

(if available)

Description

Causes

Solutions

“Service”

from “F03” to “F43”

(except “F18” and

“F24”)

“Electrical module fault”

Push the “Reset” button for at least 3 seconds.

“F24” May appear for very water-soaking laundry, or if you added

too much laundry for a programme destined for small loads

only. Do not overload the washing machine.

Push the “Reset” button for at least 3 seconds to stop the

programme. Select and start “Rinse and Spin” programme

to complete the interrupted wash programme properly.

“F02” or “FA”

(if available on your

model, will

light up)

“Waterstop fault”

Turn the programme selector to the “Off/O” position, pull out

the mains plug and turn the water tap off. Tilt the appliance

forward carefully (a second person must help you) to allow

collected water to flow out from the bottom. Then:

• Plug in the appliance again.

• Turn the water tap on (if water immediately flows into the

appliance without the appliance being started, there is a

failure; turn off the tap and notify the After-Sales Service).

• Select and start the desired programme again.

“F18” or “Fod” “Overfoaming”

Too much foam interrupted the wash programme. If your

washing machine has a “Dosing Aid” function, and you used it:

check if the dosing values set for the different programme

groups correspond to the dosing values recommended for the

detergents you use (see details in separate Instructions for the

“Dosing Aid”).

• Select and start the “Rinse & Spin” programme.

• Afterwards select and start the desired programme again,

using less detergent. See also description of problem “The

machine is at a standstill....” in the previous part of the

Troubleshooting Guide.

J - 01/2013

EN 13

REMAINING MOISTURE CONTENT OF THE

LAUNDRY AFTER SPINNING

The degree of moisture remaining in the laundry after spinning mainly depends on the fabric type, the

selected programme and spin speed. The lowest remaining moisture content can be achieved using the

wash programme referred to by the Energy Label, with maximum spin speed. This programme is marked

in the separate programme chart as “Reference programme for the Energy Label”. Below a survey of the

remaining moisture content (in %) related to the various spin-drying efficiency classes:

SAVE ENERGY AND HELP PROTECTING THE

ENVIRONMENT

• You reach the best use of energy, water, detergent and time by running the programmes with the

maximum load size.

• Save energy by using a 60°C instead of a 95°C wash programme, or by using a 40°C instead of a 60°C

wash programme.

• Use “Prewash” for heavily soiled laundry only. Save detergent, time, water and energy by not selecting

“Prewash” for lightly or normally soiled laundry.

• Do not exceed the detergent dosages indicated in the manufacturer’s instructions.

• Select a high spin speed if you intend to dry your laundry in a tumble dryer, in order to reduce time and

energy for the drying process.

EXPLANATION OF THE ENERGY LABEL

(only for washing machines with Energy Label according to Directive 2010/30/EU)

The Energy Label contains information on performance and consumption of your washing machine:

The bold black arrow marks the energy efficiency class (A+++ = most efficient / D = least efficient).

Spin-drying efficiency class Remaining moisture content in %

A (= most efficient) less than 45

B 45 or more, but less than 54

C 54 or more, but less than 63

D 63 or more, but less than 72

E 72 or more, but less than 81

kWh/annum Power consumption per year

L/annum

Water consumption per year

Noise level washing

Maximum load capacity

Noise level spinning

Spin drying efficiency class

(A = most efficient /

G = least efficient)

EN 14

AFTER-SALES SERVICE

Before contacting After-Sales Service:

1. Try to remedy the problem yourself (see

“Troubleshooting Guide”).

2. Restart the programme to check whether the

problem has solved itself.

3. If the washing machine continues to function

incorrectly, call our After-Sales Service.

Specify:

• The nature of the problem.

• The washing machine model.

• The service code (number after the word

SERVICE).

The After-Sales Service sticker can be found

inside the door.

• Your full address.

• Your telephone number and area code.

After-Sales Service phone numbers and

addresses are given on the guarantee card.

Alternatively, consult the dealer where you

purchased the appliance.

ACCESSORIES

For some models, you can obtain via our After-

Sales Service or your specialist dealer:

• A Pedestal Drawer which can be installed

beneath your washing machine. It raises your

machine to allow for more comfortable loading

and unloading, as you now no longer need to

bend as far to access the door. Furthermore, it

offers a great space-management tool and

storage solution.

• A Stacking Kit, by which your dryer can be

fixed on top of your washing machine.

• A Stacking Kit Shelf, by which your dryer can

be fixed on top of your washing machine to

save space and to facilitate loading and

unloading your dryer in that high position.

• A Cover Panel Kit, by which your washing

machine can be built under a continuous kitchen

worktop, for example. Check with our After-Sales

Service or your specialist dealer if this is possible

for your washing machine model.

TRANSPORT/HANDLING

Never lift the appliance by the worktop when transporting.

1. Pull out the mains plug.

2. Turn off the tap.

3. Check that machine door and detergent dispenser are properly closed.

4. Disconnect the inlet and drain hoses.

5. Eliminate all water from the hoses and from the appliance (see “Draining Residual Water/Cleaning

The Filter”).

6. Fit the transport bolts (obligatory).

EN 15

ELECTRICAL CONNECTION

Manufacturer:

Whirlpool Europe s.r.l.

Viale Guido Borghi 27

21025 Comerio (VA)

Italy

01/2013

For Great Britain only

Warning - this appliance must be earthed

Fuse replacement

If the mains lead of this appliance is fitted with a

BS 1363A 13amp fused plug, to change a fuse in this type

of plug use an A.S.T.A. approved fuse to BS 1362 type and

proceed as follows:

1. Remove the fuse cover (A) and fuse (B).

2. Fit replacement 13A fuse into fuse cover.

3. Refit both into plug.

Important:

The fuse cover must be refitted when changing a fuse

and if the fuse cover is lost the plug must not be used

until a correct replacement is fitted.

Correct replacement are identified by the colour insert or

the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local

electrical store.

For the Republic of Ireland only

The information given in respect of Great Britain will

frequently apply, but a third type of plug and socket is

also used, the 2-pin, side earth type.

Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet,

Please contact After-Sales service for further instruction.

Please do not attempt to change plug yourself. This

procedure needs to be carried out by a qualified

technician in compliance with the manufactures

instructions and current standard safety regulations.

FR 16

USAGE PREVU

Ce lave-linge est prévu uniquement pour le

traitement des tissus lavables en machine, selon

les quantités habituelles d'un ménage.

• Respectez les instructions fournies dans la

présente notice d'utilisation, le guide

d'installation et le tableau des programmes

lorsque vous utilisez ce lave-linge.

• Conservez la présente notice d'utilisation, le

tableau des programmes et le guide

d'installation. Si vous cédez votre appareil à une

autre personne, veillez également à lui

transmettre ces documents.

MESURES DE SECURITE ET CONSEILS D'ORDRE

GENERAL

1. Mesures de sécurité

• Ce lave-linge doit être installé

à l'intérieur, jamais à

l'extérieur.

• Ne stockez aucun produit

inflammable à proximité du

lave-linge.

• Ce lave-linge peut être utilisé

par les enfants à partir de

8 ans, ainsi que par les

personnes à capacités

physiques, sensorielles ou

mentales réduites ou n'ayant

pas l'expérience ou les

connaissances requises, à

condition qu'ils soient

supervisés ou guidés quant à

l'utilisation sûre de l'appareil

et qu'ils soient bien informés

des dangers inhérents à son

utilisation. Les enfants ne

doivent pas jouer avec le lave-

linge. Le nettoyage et

l'entretien du lave-linge ne

doivent pas être effectués par

des enfants sans supervision.

• N'utilisez pas le lave-linge si la

température est inférieure

à5°C.

• Si vous souhaitez installer un

sèche-linge au-dessus de

votre lave-linge, vérifiez

d'abord si cela est possible

auprès du Service Après-

Vente ou de votre revendeur

spécialisé. Une telle

configuration implique la

fixation du sèche-linge sur le

lave-linge à l'aide d'un kit de

superposition adéquat,

disponible auprès du Service

Après-Vente ou de votre

revendeur spécialisé.

• Au terme de l'installation,

l'accès à la prise secteur ou la

coupure de l'alimentation

secteur doivent pouvoir

s'effectuer à tout moment par

le biais d'un interrupteur

bipolaire.

• Fermez le robinet lorsque

l'appareil n'est pas utilisé.

• Avant de procéder au

nettoyage ou à l'entretien,

débranchez l'appareil.

• Ne tirez pas de force sur le

hublot pour l'ouvrir et ne

montez pas dessus.

FR 17

• Lorsque cela est nécessaire,

remplacez le câble

d'alimentation par un câble

identique à celui d'origine,

disponible auprès du Service

Après-Vente. Pour éviter tout

danger, ce remplacement doit

impérativement être effectué

par un technicien qualifié ou

par notre Service Après-Vente.

2.Emballage

• Les matériaux d'emballage sont entièrement

recyclables et portent le symbole du recyclage

. Suivez les réglementations locales en

vigueur pour mettre au rebut les matériaux

d'emballage.

3.Mise au rebut des emballages et des

appareils usagés

• Ce lave-linge est fabriqué à partir de matériaux

recyclables. Il doit être mis au rebut

conformément aux réglementations locales en

vigueur.

• Avant de vous débarrasser de votre appareil,

retirez toute trace de détergent et rendez le

lave-linge inutilisable en sectionnant le câble

d'alimentation.

• Cet appareil porte le symbole du recyclage

conformément à la directive européenne

2002/96/CE relative aux déchets

d'équipements électriques et électroniques

(DEEE).

En procédant correctement à la mise au rebut

de cet appareil, vous contribuerez à empêcher

toute conséquence nuisible à l'environnement

et la santé.

Le symbole présent sur l'appareil ou sur la

documentation qui l'accompagne indique qu'il

ne peut en aucun cas être traité comme un

déchet ménager. Il doit par conséquent être

remis à un centre de collecte des déchets

chargé du recyclage des équipements

électriques et électroniques.

La mise au rebut doit être effectuée

conformément aux réglementations locales en

vigueur relatives à la protection de

l'environnement.

Pour obtenir de plus amples informations

concernant le traitement, la récupération et le

recyclage de ce produit, contactez le service

municipal ou la déchetterie de votre ville, ou

bien encore le magasin où vous avez acheté le

produit.

4.Gel

N'installez pas le lave-linge dans une pièce

exposée au gel. Le cas échéant, assurez-vous que

le lave-linge est correctement vidangé après

chaque utilisation :

• Débranchez le ou les tuyaux d'arrivée d'eau du

robinet d'eau et laissez l'eau s'écouler

complètement.

• Retirez le tuyau de vidange du siphon ou de la

colonne montante et laissez l'eau s'écouler

complètement.

• Eliminez l'eau encore présente dans l'appareil

en suivant les instructions figurant au chapitre

« Vidange de l'eau résiduelle ». Avec l'aide d'une

autre personne, faites basculer l'appareil vers

l'avant pour permettre à l'eau de s'écouler

complètement.

5.Déclaration de conformité CE

• Cet appareil est conforme aux normes

européennes suivantes :

Directive 2006/95/CE relative à la basse tension

Directive 2004/108/CE relative à la

compatibilité électromagnétique

Le fabricant n'est pas responsable de la

détérioration du linge découlant du non-respect

des instructions d'entretien fournies avec le

vêtement ou l'article.

FR 18

AVANT D'UTILISER LE LAVE-LINGE

1.Retrait de l'emballage et vérification

• Après avoir déballé le lave-linge, vérifiez qu'il

n'a pas été endommagé pendant le transport.

Si vous avez des doutes, ne l'utilisez pas.

Contactez le Service Après-Vente ou votre

revendeur local.

• Les matériaux d'emballage (sachets en

plastique, éléments en polystyrène, etc.)

doivent être tenus hors de portée des enfants,

car ils constituent un danger potentiel.

• Si l'appareil a été exposé au froid avant d'être

livré, maintenez-le à température ambiante

pendant quelques heures avant de le mettre en

marche.

2.Retrait des écrous de transport

• Le lave-linge est doté d'écrous de transport

destinés à éviter tout endommagement

intérieur pendant le transport. Avant de mettre

l'appareil en service, il est impératif de retirer les

écrous de transport.

• Une fois les écrous retirés, obturez les

ouvertures à l'aide des 4 obturateurs en

plastique fournis.

3.Installation du lave-linge

• Retirez le film de protection du bandeau de

commandes (le cas échéant).

• Ne déplacez jamais l'appareil en le tenant par la

surface supérieure.

• Placez l'appareil sur une surface plane et stable,

si possible dans un coin de la pièce.

• Assurez-vous que les quatre pieds reposent

correctement sur le sol et que l'appareil est bien

horizontal (utilisez un niveau à bulle).

• Si l'appareil est installé sur un plancher en bois

ou sur un plancher flottant (certains parquets

ou planchers lamellés, par exemple), placez-le

sur un panneau en contre-plaqué de

60 x 60 cm de largeur/longueur minimum et de

3 cm d'épaisseur minimum, préalablement fixé

au sol.

• Assurez-vous que les orifices de ventilation à la

base de votre lave-linge (selon le modèle) ne

sont pas obstrués par de la moquette ou tout

autre matériau.

4.Arrivée d'eau

• Raccordez le ou les tuyaux d'arrivée d'eau à

l'arrivée d'eau potable conformément aux

prescriptions de votre compagnie de

distribution d'eau.

• Pour les appareils à vanne d'arrivée d'eau

unique : eau froide

• Pour les appareils à vanne d'arrivée d'eau

double : eau froide ET eau chaude, ou eau

froide seulement (voir le guide d'installation

séparé).

• Robinet d'arrivée d'eau

: raccord tuyau fileté de 3/4”

• Pression d'eau

(pression de débit)

: 100-1 000 kPa (1-10 bars).

• Utilisez exclusivement des tuyaux neufs pour

raccorder votre lave-linge à l'arrivée d'eau.

N'utilisez en aucun cas des tuyaux usagés ;

mettez-les au rebut.

• Pour les modèles avec arrivée d'eau chaude : la

température de l'eau chaude à l'arrivée ne doit

pas dépasser 60 °C.

5.Vidange

• Raccordez le tuyau de vidange au siphon ou à

tout autre raccord de vidange d'eau (voir le

guide d'installation séparé).

• Si l'appareil est connecté à un système de vidange

intégré, assurez-vous que ce dernier est équipé

d'un évent pour empêcher le remplissage et la

vidange d'eau simultanés (effet de siphon).

6.Branchement électrique

• Les branchements électriques doivent être

réalisés par un technicien qualifié,

conformément aux instructions du fabricant et

aux normes de sécurité locales en vigueur.

• Les données techniques (tension,

consommation électrique et fusibles) figurent à

l'intérieur du hublot.

• L'appareil doit être branché au réseau au moyen

d'une prise de terre, conformément aux

réglementations en vigueur. La loi exige que cet

appareil soit mis à la terre. Le fabricant décline

toute responsabilité en cas de blessures

corporelles ou de dommages matériels résultant

du non-respect des instructions ci-dessus.

• N'utilisez ni rallonge ni multiprise.

• Débranchez le lave-linge avant de procéder à

son entretien.

• N'utilisez en aucun cas l'appareil s'il a été

endommagé pendant le transport. Signalez-le

au Service Après-Vente.

• Le remplacement du câble d'alimentation peut

être réalisé uniquement par le Service Après-

Vente.

• Lors de l'utilisation d'un disjoncteur à courant

résiduel (RCCB), utilisez uniquement un modèle

portant le symbole .

La page charge ...

Bauknecht EXCELLENCE 720P Mode d'emploi

Marque: Bauknecht

Modèle: EXCELLENCE 720P

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Bauknecht EXCELLENCE 720P User guide

Bauknecht EXCELLENCE 720P Mode d'emploi

Bauknecht EXCELLENCE 720P Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents