Hobart H-9B Le manuel du propriétaire

Catégorie
Système de soudage
Taper
Le manuel du propriétaire

Ce manuel convient également à

www.HobartWelders.com
OM-225 333B 201205
Processes
Description
MIG (GMAW) Welding (Optional)
Flux Cored (FCAW) Welding
Semi-Automatic, Air-Cooled
Flux Cored (FCAW) And MIG
(GMAW) Welding Gun
H-9B Gun
File: Flux Cored (FCAW)
TABLE OF CONTENTS
SECTION 1 SAFETY PRECAUTIONS FOR GMAW WELDING GUNS READ BEFORE USING 1......
1-1. Symbol Usage 1.................................................................
1-2. Arc Welding Hazards 1............................................................
1-3. Proposition 65 Warnings 2.........................................................
1-4. Principal Safety Standards 2.......................................................
1-5. EMF Information 2................................................................
SECTION 2 MESURES DE SÉCURITÉ VISANT LES PISTOLETS DE SOUDAGE GMAW À LIRE AVANT
UTILISATION 3..............................................................................
2-1. Signification des symboles 3.......................................................
2-2. Dangers relatifs au soudage à l’arc 3................................................
2-3. Proposition californienne 65 Avertissements 4.........................................
2-4. Principales normes de sécurité 4....................................................
2-5. Informations relatives aux CEM 4...................................................
SECTION 3 INSTALLATION 5................................................................
3-1. Specifications 5..................................................................
3-2. Duty Cycle And Overheating 5......................................................
3-3. Installing Gun Into Welding Power Source 6...........................................
3-4. Installing Contact Tip And Nozzle 7..................................................
3-5. Threading Welding Wire 8..........................................................
SECTION 4 OPERATION 9..................................................................
4-1. Operating The Gun 9..............................................................
SECTION 5 MAINTENANCE & TROUBLESHOOTING 10.........................................
5-1. Replacing Gun Contact Tip 10.......................................................
5-2. Cleaning Gun Liner 10..............................................................
5-3. Replacing Gun Liner 11.............................................................
5-4. Replacing Switch/Handle 13.........................................................
5-5. Removing Gun From Welding Power Source 14........................................
5-6. Routine Maintenance 15............................................................
5-7. Troubleshooting 15................................................................
SECTION 6 PARTS LIST 16...................................................................
WARRANTY
Hobart is registered to
the ISO 9001 Quality
System Standard.
OM-225 333 Page 1
SECTION 1 SAFETY PRECAUTIONS FOR GMAW
WELDING GUNS READ BEFORE USING
SR7 (MIG) 2011-10
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or ex-
plained in the text.
NOTICE Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-
bols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the welding power source Owners Manual. Read
and follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
D Always wear dry insulating gloves.
D Insulate yourself from work and ground.
D Do not touch live electrode or electrical parts.
D Repair or replace worn, damaged, or cracked gun or cable insula-
tion.
D Turn off welding power source before changing contact tip or gun
parts.
D Keep all covers and handle securely in place.
D Keep your head out of the fumes.
D Ventilate area, or use breathing device.
D Read Material Safety Data Sheets (MSDSs)
and manufacturer’s instructions for material
used.
FUMES AND GASES can be hazardous.
D Do not weld near flammable material.
D Do not weld on containers that have held com-
bustibles, or on closed containers such as
tanks, drums, or pipes unless they are properly prepared ac-
cording to AWS F4.1 and AWS A6.0 (see Safety Standards).
D Watch for fire; keep extinguisher nearby.
WELDING can cause fire or explosion.
BUILDUP OF GAS can injure or kill.
D Shut off compressed gas supply when not in
use.
D Always ventilate confined spaces or use ap-
proved air-supplied respirator.
MOVING PARTS can injure.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D Wear welding helmet with correct shade of fil-
ter.
D Wear correct eye and body protection.
D Cover exposed skin with spatter-resistant
clothing.
ARC RAYS can burn eyes and skin.
HOT PARTS can burn.
D Allow gun to cool before touching.
D Do not touch hot metal.
D Protect hot metal from contact by others.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Check for noise level limits exceeding those
specified by OSHA.
D Use approved ear plugs or ear muffs if noise level is high.
D Warn others nearby about noise hazard.
WELDING WIRE can injure.
D Keep hands and body away from gun tip when
trigger is pressed.
READ INSTRUCTIONS.
D Read and follow all labels and the Owners
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D Use only genuine replacement parts from the manufacturer.
D Perform maintenance and service according to the Owner’s
Manuals, industry standards, and national, state, and local
codes.
OM-225 333 Page 2
1-3. Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-4. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practice For Occupational And Educational Eye And Face Protec-
tion, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-
site: www.ansi.org).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Glob-
al Engineering Documents (phone: 1-877-413-5184, website: www.glo-
bal.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Com-
bustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protec-
tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protec-
tion, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-
site: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Indus-
try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Super-
intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
1-5. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). Welding current creates an EMF field
around the welding circuit and welding equipment. EMF fields may inter-
fere with some medical implants, e.g. pacemakers. Protective meas-
ures for persons wearing medical implants have to be taken. For ex-
ample, restrict access for passersby or conduct individual risk assess-
ment for welders. All welders should use the following procedures in or-
der to minimize exposure to EMF fields from the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recom-
mended.
OM-225 333 Page 3
SECTION 2 MESURES DE SÉCURITÉ VISANT LES
PISTOLETS DE SOUDAGE GMAW À LIRE AVANT
UTILISATION
SR7(MIG)_201110fre
Pour écarter les risques de blessure pour vousmême et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Signification des symboles
DANGER! Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dan-
gers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
NOTE Indique des déclarations pas en relation avec des blessures
personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les ris-
ques de danger. Lorsque vous voyez un symbole, soyez vigi-
lant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne
font que résumer l’information contenue dans les normes de
sécurité énumérées dans le manuel d’utilisation du poste de
soudage. Veuillez lire et respecter toutes ces normes de sé-
curité.
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
UN CHOC ÉLECTRIQUE peut tuer.
D Porter toujours des gants secs et isolants.
D S’isoler de la pièce et de la terre.
D Ne jamais toucher une électrode ou des pièces
électriques sous tension.
D Réparer ou remplacer un pistolet ou la gaine d’isolement d’un
câble usée, endommagée ou fissurée.
D Mettre la soudeuse hors tension avant de remplacer un bec con-
tact ou des pièces de pistolet.
D S’assurer que tous les couvercles et poignées sont fermement
assujettis.
LES VAPEURS ET LES FUMÉES
peuvent être nocives.
D Éloigner sa tête des endroits renfermant des
vapeurs.
D Aérer la zone de travail ou porter un appareil re-
spiratoire.
D Consulter les fiches toxicologiques (MSDS) et les notices du fab-
ricant de chaque matériel utilisé.
LE SOUDAGE peut causer un incen-
die ou une explosion.
D Ne pas souder à proximité de matériaux inflam-
mables.
D Ne pas effectuer le soudage sur des conte-
neurs fermés tels que des réservoirs,
tambours, ou conduites, à moins qu’ils n’aient
été préparés correctement conformément à
AWS F4.1 et AWS A6.0 (voir les Normes de
Sécurité).
D Prendre garde aux incendies et toujours avoir un extincteur à
proximité.
L’ACCUMULATION DE VAPEURS
peut causer des lésions ou la mort.
D Quand on n’utilise pas le gaz comprimé de
protection, fermer le robinet de la bouteille.
D Assurer toujours la ventilation des zones fer-
mées ou utiliser un appareil respiratoire avec
alimentation en air.
Les PIÈCES MOBILES peuvent
causer des blessures.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LE RAYONNEMENT DE L’ARC peut
brûler les yeux et la peau.
D Porter un casque de soudage muni d’un filtre
de protection oculaire approprié.
D Porter une protection oculaire et des vête-
ments de protection appropriés.
D Protéger la peau nue en portant des vêtements anti-éclabous-
sures.
OM-225 333 Page 4
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
D Laisser refroidir le pistolet avant de le toucher.
D Ne pas toucher d’objets métalliques chauds.
D Abriter les objets métalliques contre tout con-
tact par les personnes à proximité.
Le BRUIT peut endommager l’ouie.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Vérifier si les niveaux de bruit excèdent les lim-
ites spécifiées par l’OSHA.
D Utiliser des bouche-oreilles ou des serre-tête antibruit approuvés
si le niveau de bruit est élevé.
D Avertir les personnes à proximité au sujet du danger inhérent au
bruit.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D Éloigner les mains et le corps de la buse du pis-
tolet après avoir appuyé sur la gâchette.
LIRE LES INSTRUCTIONS.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant
l’installation, l’utilisation ou l’entretien de
l’appareil. Lire les informations de sécurité au
début du manuel et dans chaque section.
D N’utiliser que les pièces de rechange recommandées par le
constructeur.
D Effectuer l’entretien en respectant les manuels d’utilisation,
les normes industrielles et les codes nationaux, d’état et locaux.
2-3. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des
malformations congénitales et, dans certains cas, des
cancers. (Code de santé et de sécurité de Californie, chapitre
25249.5 et suivants)
Ce produit contient des éléments chimiques, dont le plomb,
reconnus par l’État de Californie pour leur caractère
cancérogène ainsi que provoquant des malformations
congénitales ou autres problèmes de procréation. Se laver
les mains après toute manipulation.
2-4. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practice For Occupational And Educational Eye And Face Protec-
tion, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-
site: www.ansi.org).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Glob-
al Engineering Documents (phone: 1-877-413-5184, website: www.glo-
bal.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Com-
bustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protec-
tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protec-
tion, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-
site: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Indus-
try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Super-
intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
2-5. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant de soudage
crée un CEM autour du circuit et du matériel de soudage. Les CEM
peuvent créer des interférences avec certains implants médicaux
comme des stimulateurs cardiaques. Des mesures de protection pour
les porteurs d’implants médicaux doivent être prises: Limiter par
exemple tout accès aux passants ou procéder à une évaluation des
risques individuels pour les soudeurs. Tous les soudeurs doivent
appliquer les procédures suivantes pour minimiser l’exposition aux
CEM provenant du circuit de soudage:
1 Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2 Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
3 Ne pas courber et ne pas entourer les câbles autour de votre
corps.
4 Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
5 Connecter la pince sur la pièce aussi près que possible de la
soudure.
6 Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7 Ne pas souder tout en portant la source de soudage ou le
dévidoir.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induc-
tion. Si le médecin approuve, il est recommandé de suivre les procédu-
res précédentes.
OM-225 333 Page 5
SECTION 3 INSTALLATION
3-1. Specifications
804 240-A
Air-Cooled Welding Gun For FCAW And GMAW Welding
H-9B Feeds .030 .035 in. (0.8 0.9 mm) Flux Cored Wire Or .023 .030 in. (0.6 0.8 mm) Solid Wire
Duty Cycle Rating:
60%: 70 A With Flux Cored Wire
60%: 90 A With CO
2
Shielding Gas
60%: 70 A With Mixed Gases
Weight With 8 ft (2.4 m) Power Cable: 2.2 lb (1.0 kg)
Duty Cycle is percentage of 10
minutes that unit can weld at rated
load without overheating.
NOTICE Exceeding duty cycle
can damage unit and void warranty.
See Section 3-1. Specifications for amperage
rating and duty cycle.
Overheating
0
15
A or V
OR
Reduce Duty Cycle
Minutes
sduty1 5/95
Continuous Welding
100%dutycycle
3-2. Duty Cycle And Overheating
6 Minutes Welding 4 Minutes Resting
60%dutycycle
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-225 333 Page 6
3-3. Installing Gun Into Welding Power Source
803 497-A / Ref. 803 378-A
Open pressure assembly.
Remove screws (3) from
cover, and remove cover
from wire drive assembly.
Insert gun cable through opening in front
panel. Route weld cable, trigger leads, and
gas hose through opening in drive housing.
Reinstall cover and
secure with screws (3).
Remove wrapper from
unit.
Connect gas hose to adapter
(if unit is not equipped with
gas solenoid valve, secure
hose to wiring harness).
Connect trigger leads to
RC3 and RC4 on PC1.
Route weld cable through
opening in baffle.
Connect weld cable
to weld terminal.
Reinstall wrapper onto unit.
Secure leads and hose
with cable tie(s).
. Thread wire according to
Section 3-5.
! Turn off and disconnect input
power.
. If existing gun requires
removal, see Section 5-5.
. Route wires, cable, and hose to avoid contact
with sharp edges, hot surfaces, or moving parts.
Reinstall cable end into drive housing
with retaining grooves inserted into the
two retaining ribs. Be sure to position
gas hose up and trigger leads down.
Position liner in groove so that end is
flush with back of groove.
OM-225 333 Page 7
3-4. Installing Contact Tip And Nozzle
Tools Needed:
Ref. 804 241-A
! Turn off and disconnect input
power.
1 Nozzle
Remove nozzle.
2 Contact Tip
3 Tip Adapter
Thread welding wire through gun (see
Section 3-5).
Slide contact tip over wire and tighten
tip into tip adapter.
Install nozzle.
1
2
3
Flux Nozzle MIG Nozzle
Use with flux cored wire only.
Narrow design allows access in
tight spaces and provides better
visibility of puddle during welding.
Use with solid or flux cored wire.
Push nozzle over contact tip and
adapter until it is seated onto
adapter. Contact tip will be
exposed approximately 7/16 in.
(11.3 mm) when installed properly.
Push nozzle over contact tip and
adapter until it is seated onto
adapter. End of contact tip will be
flush with end of nozzle when
installed properly.
OM-225 333 Page 8
3-5. Threading Welding Wire
1 Wire Spool
2 Welding Wire
3 Inlet Wire Guide
4 Pressure Adjustment Knob
5 Drive Roll
6 Gun Cable
Lay gun cable out straight.
Tools Needed:
6
1
Pull and hold wire; cut off end.
4 in.
(102 mm)
Remove gun nozzle and contact tip.
Open pressure assembly. Push wire thru guides into gun liner;
continue to hold wire.
. Hold wire tightly to keep it
from unraveling.
Ref. 803 444-A / Ref. 205 837
WOOD
Feed wire to check drive roll pressure.
Tighten knob enough to prevent slipping.
Cut off wire. Close door.
Press gun trigger until wire comes
out of gun.
2
Turn power on.
INPUT
POWER
6 in.
(150 mm)
Tighten
Tighten
Be sure that wire is positioned
in proper feed roll groove.
Close and tighten pressure
assembly, and let go of wire.
Be sure that contact tip matches wire diameter.
Reinstall tip adapter, if applicable, contact tip
and nozzle.
3
5
4
. Tip adapter may also require removal
to allow wire to feed out end of gun.
. Loosen knob completely, then rotate
pressure adjustment knob in a
clockwise direction until drive roll is
tight against the welding wire.
Adjust drive roll pressure just
tightly enough to prevent wire
from slipping against drive roll
during operation.
OM-225 333 Page 9
SECTION 4 OPERATION
4-1. Operating The Gun
Ref. 804 240-A
1 Trigger Switch
When pressed, energized wire
feeds and shielding gas flows (if
unit is equipped with optional gas
solenoid).
1
Notes
OM-225 333 Page 10
SECTION 5 MAINTENANCE & TROUBLESHOOTING
5-1. Replacing Gun Contact Tip
Ref. 804 241-A
! Turn off and disconnect input
power.
1 Nozzle
Remove nozzle.
2 Contact Tip
3 Tip Adapter
Cut off welding wire at contact tip.
Remove contact tip from tip adapter,
and install new contact tip. Reinstall
nozzle.
Tools Needed:
1
2
3
5-2. Cleaning Gun Liner
804 241-A / 803 838-A
! Turn off and disconnect input
power.
1 Nozzle
2 Contact Tip
3 Adapter
Head
Tube
Tools Needed:
8 mm
Lay gun cable out straight,
and blow out liner.
Remove nozzle. Cut off wire
at contact tip, and remove
contact tip and tip adapter.
. Thread wire according to
Section 3-5.
Reassemble drive cover
and gun in reverse order
from taking it apart.
Open pressure assembly. Retract
wire from liner onto spool.
. Hold wire tightly to keep it
from unraveling. Secure
end of wire at spool.
Remove screws (3) from
cover, and remove cover
from wire drive assembly.
8 mm
1
2
3
OM-225 333 Page 11
5-3. Replacing Gun Liner
Ref. 804 241-A / 803 497-A / 803 837-A / 803 899-A
Tools Needed:
8 mm / 10 mm
Remove nozzle. Cut off wire
at contact tip, and remove
contact tip and tip adapter.
Open pressure assembly. Retract
wire from liner onto spool.
. Hold wire tightly to keep it
from unraveling. Secure
end of wire at spool.
Twist top and bottom handle locking rings
counterclockwise 1/4 turn. Slide bottom ring
down cable and top ring forward over head
tube. Separate gun handle halves.
Loosen liner setscrew.
Loosen and remove
retaining nut from liner.
Pull liner out of gun
cable. If necessary, twist
cable to ease removal.
! Turn off and disconnect input
power.
Install retaining nut on one end of liner. Lay
gun cable straight on a flat surface. Insert
bare end of liner (end without retaining nut)
into wire drive end of cable. Push liner
toward gun. If necessary, twist cable to
ease installation.
Remove screws (3) from
cover, and remove cover
from wire drive assembly.
8 mm
Remove black sleeving from
end of replacement liner.
Head
Tube
8 mm
1
2
3
OM-225 333 Page 12
5-3. Replacing Gun Liner (Continued)
When liner exits cable at gun
handle, guide liner into head
tube. Continue to push liner until
it exits end of head tube.
Slide locking rings over top and
bottom of handle, and secure by
twisting rings clockwise 1/4 turn.
Place other half of handle over
head tube and cable.
Be sure that cable is straight.
Tighten liner setscrew. Cut
liner so that 3/8 in. (10 mm)
sticks out of head tube. File
down any sharp points on
liner after cutting to length.
3/8 in (10 mm)
Reassemble gun by placing head tube
and cable into one half of handle. Be
sure trigger is properly installed into
trigger slot.
Thread welding wire through
gun (see Section 3-5). Reinstall
adapter, contact tip, and nozzle.
Reinstall cover onto wire
drive assembly, and secure
with screws (3).
Insert retaining nut into adapter, and adjust liner stickout as
shown. Tighten retaining nut. Reinstall cable end into drive
housing with retaining grooves inserted into the two retaining
ribs. Be sure to position gas hose up. Position liner in groove
so that end is flush with back of groove, adjust if necessary
13/16 in.
(21 mm)
8 mm
8 mm
OM-225 333 Page 13
5-4. Replacing Switch/Handle
! Turn off and disconnect input
power.
Disconnect switch leads and remove
switch. Connect leads to new switch
(polarity is not important). Be sure
trigger is properly installed into trigger
slot. Reassemble in reverse order.
Ref. 804 241-A / 804 242-A
Twist top and bottom handle locking rings
counterclockwise 1/4 turn. Slide bottom ring
down cable and top ring forward over head
tube. Separate gun handle halves.
Notes
BUTT
BUTT
BUTT
BUTT
TJOINT
TJOINT
TJOINT
TJOINT
FILLET
GROOVE
FLAT VERTICALHORIZONTAL OVERHEADWELD POSITION:
WELD JOINT
TYPES
Ref. AWS/ANSI D1.1
1G
1F
2G
2F
3G
3F
4G
4F
Ref. 804 248-A
OM-225 333 Page 14
5-5. Removing Gun From Welding Power Source
803 497-A / Ref. 803 378-A / 803 838-A
Pull weld cable, trigger leads, and gas hose
through opening in drive housing. Pull gun
cable out through opening in front panel. To
reinstall gun see Section 3-3.
Remove wrapper from
unit.
Disconnect gas hose from
adapter (if unit is not
equipped with gas solenoid
valve, loosen hose from
wiring harness).
Disconnect trigger leads from
RC3 and RC4 on PC1.
Pull weld cable through
opening in baffle.
Disconnect weld
cable from weld
terminal.
Remove leads and
hose from cable tie(s).
! Turn off and disconnect input
power.
Remove nozzle. Cut off wire
at contact tip, and remove
contact tip and tip adapter.
Open pressure assembly. Retract
wire from liner onto spool.
. Hold wire tightly to keep it
from unraveling. Secure
end of wire at spool.
Remove screws (3) from
cover, and remove cover
from wire drive assembly.
Head
Tube
8 mm
OM-225 333 Page 15
5-6. Routine Maintenance
! Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
n = Check Z = Change ~ = Clean l = Replace
* To be done by Factory Authorized Service Agent
Reference
Each
Spool
Of Wire
n~ Nozzle and contact tip ~ Blow out gun casing
Every
3
Months
l Unreadable Labels ~ Weld Terminals l Damaged Gas Hose nl Weld Cables
nl Cords nl Gun Cables
5-7. Troubleshooting
Trouble Remedy
Wire does not feed; wire is not ener-
gized; wire feeds unevenly.
Check contact tip. Check for kinks in gun cable.
Check contact tip. Check for kinks in gun cable. Blow out gun liner (see Section 5-2).
Check for secure gun trigger lead connections at PC1 (see Section 3-3).
Check, and if necessary, replace gun trigger switch (see Section 5-4).
Weld porosity.
Remove weld spatter buildup in nozzle.
Make sure inner head tube is tight in cable connector.
Check shielding gas flow/supply.
Wire feeding stops or does not feed
properly during welding.
Straighten gun cable and/or replace damaged parts (see Section 5-2 or 5-3).
Adjust drive roll pressure (see Section 3-5).
Change to proper drive roll groove (see welding power source manual).
Readjust hub tension (see weld power source manual).
Clean or replace liner if dirty or plugged (see Section 5-2 or 5-3).
Replace drive roll or pressure bearing if worn or slipping (see welding power source manual).
OM-225 333 Page 16
SECTION 6 PARTS LIST
1
804 243-A
2
3
5 See Table 6-1
4
6
7
7
Figure 6-1. H-9B Gun
Description
Part
No.
225 397
Item
No.
Figure 6-1. H-9B Gun
Quantity
1 169 715 NOZZLE, slip type .500 orf flush 1... ............. .. ..................................
1 226 190 NOZZLE, flux cored slip type 1... ............ .. .....................................
2 169 716 ADAPTER, contact tip 1... ............. .. ...........................................
3 225 410 SWITCH, trigger 1... ............. .. ................................................
4 210 970 LINER, monocoil .023/.035 wire x 8ft 1... ............. .. ...............................
5 087 299 TIP, contact scr .023 wire x 1.125... ............ ..
5 000 067 TIP, contact scr .030 wire x 1.125 1... ............. .. ..................................
5 000 068 TIP, contact scr .035 wire x 1.125... ............ ..
6 226 010 NUT, liner retainer 1... ............. .. ...............................................
7 226 080 HANDLE ASSY 1... ............. .. .................................................
OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturers Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
Table 6-1. Contact Tip Options
HOBART PART NO. DESCRIPTION REMARKS
196 134 Tip, contact scr .023 wire Pkg of 5
196 131 Tip, contact scr .030 wire Pkg of 5
196 132 Tip, contact scr .035 wire Pkg of 5
196 137 Nozzle, slip type .500 orf flush Qty 1
196 135 Adapter, contact tip Qty 1
WELD-IT PART NO. DESCRIPTION REMARKS
770 174 Tip, contact scr .023 wire Pkg of 5
770 177 Tip, contact scr .030 wire Pkg of 5
770 180 Tip, contact scr .035 wire Pkg of 5
Warranty Questions?
Call
1-800-332-3281
7 AM 5 PM EST
hobart_warr 2012-03
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor or
call 1-800-332-3281. The
expertise of the distributor
and Hobart is there to
help you, every step of
the way.
Assistance
Visit the Hobart website:
www.HobartWelders.com
Effective January 1, 2012
5/3/1 WARRANTY applies to all Hobart welding equipment, plasma cutters and spot welders with a
serial number preface of MC or newer.
This limited warranty supersedes all previous Hobart warranties and is exclusive with
no other guarantees or warranties expressed or implied.
Hobart products are serviced by Hobart or Miller Authorized Service Agencies.
LIMITED WARRANTY Subject to the terms and conditions
below, Hobart Brothers Co., Troy, Ohio, and Miller Electric Mfg.
Co., Appleton, Wisconsin, warrants to its original retail purchaser
that new Hobart equipment sold after the effective date of this
limited warranty is free of defects in material and workmanship at
the time it is shipped by Hobart. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
Within the warranty periods listed below, Hobart/Miller will repair
or replace any warranted parts or components that fail due to
such defects in material or workmanship. Hobart/Miller must be
notified in writing within thirty (30) days of such defect or failure, at
which time Hobart/Miller will provide instructions on the warranty
claim procedures to be followed.
Hobart/Miller shall honor warranty claims on warranted
equipment listed below in the event of such a failure within the
warranty time periods. All warranty time periods start on the
delivery date of the equipment to the original retail purchaser, and
not to exceed one year after the equipment is shipped to a North
American distributor or eighteen months after the equipment is
shipped to an International distributor.
1. 5 Years — Parts and Labor
* Original Main Power Rectifiers only to include SCRs,
diodes, and discrete rectifier modules
* Reactors
* Stabilizers
* Transformers
2. 3 Years — Parts and Labor
* Drive Systems
* Idle Module
* PC Boards
* Rotors, Stators and Brushes
* Solenoid Valves
* Spot Welder Transformer
* Switches and Controls
3. 1 Year — Parts and Labor Unless Specified
(90 days for industrial use)
* Accessories
* Batteries (Trek 180 Only)
* Contactors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in, or
for a minimum of one year — whichever is greater.)
* Flowgauge and Flowmeter Regulators (No Labor)
* HF Units
* MIG Guns/TIG Torches
* Motor-Driven Guns
* Plasma Cutting Torches
* Regulators
* Relays
* Remote Controls
* Replacement Parts (No labor) 90 days
* Running Gear/Trailers
* Water Coolant Systems
4. Engines, batteries (except Trek 180) and tires are
warranted separately by the manufacturer.
Hobart’s 5/3/1 Limited Warranty shall not apply to:
1. Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
2. Items furnished by Hobart/Miller, but manufactured by
others, such as engines or trade accessories. These
items are covered by the manufacturer’s warranty, if
any.
3. Equipment that has been modified by any party other
than Hobart/Miller, or equipment that has been
improperly installed, improperly operated or misused
based upon industry standards, or equipment which has
not had reasonable and necessary maintenance, or
equipment which has been used for operation outside of
the specifications for the equipment.
HOBART PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Hobart’s/Miller’s option: (1) repair;
or (2) replacement; or, where authorized in writing by
Hobart/Miller in appropriate cases, (3) the reasonable cost of
repair or replacement at an authorized Hobart/Miller service
station; or (4) payment of or credit for the purchase price (less
reasonable depreciation based upon actual use) upon return of
the goods at customer’s risk and expense. Hobart’s/Miller’s
option of repair or replacement will be F.O.B., Factory at
Appleton, Wisconsin, or F.O.B. at a Hobart/Miller authorized
service facility as determined by Hobart/Miller. Therefore no
compensation or reimbursement for transportation costs of any
kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL HOBART/MILLER BE
LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION, OPERATION OF LAW,
CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO
ANY AND ALL EQUIPMENT FURNISHED BY
HOBART/MILLER IS EXCLUDED AND DISCLAIMED BY
Hobart/Miller.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
Resources Available
Always provide Model Name and Serial/Style Number.
To locate a Service Center:
Call 1-800-332-3281
or visit our website at www.HobartWelders.com/wheretobuy
For Technical Assistance:
Call 1-800-332-3281
7 AM to 5 PM EST Monday through Friday
ORIGINAL INSTRUCTIONS PRINTED IN USA 2012 Hobart Brothers Co.. 2012-03
Hobart Brothers Co.
An Illinois Tool Works Company
600 West Main Street
Troy, OH 45373 USA
For Assistance:
Call1-800-332-3281
Model Name Serial/Style Number
Purchase Date (Date which equipment was delivered to original customer.)
Distributor
Address
City
State Zip
Please complete and retain with your personal records.
Owner’s Record
Thank you for purchasing Hobart. Our trained technical support team is
dedicated to your satisfaction. For questions regarding performance, op-
eration, or service, contact us!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Hobart H-9B Le manuel du propriétaire

Catégorie
Système de soudage
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues