Dometic MAGICCOMFORT MSH300 Mode d'emploi

Taper
Mode d'emploi
MSH300, MSH301
Retrofit insert seat heater
Installation and Operating Manual. . . . . . . .9
Nachrüstbare Einbau-Sitzheizung
Montage- und Bedienungsanleitung. . . . .20
Calefacción del asiento como
aditamento adicional
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chauffage de siège, montage
ultérieur
Instrucciones de montaje y de uso . . . . . . .43
Aquecimento de banco para
retromontagem
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Riscaldamento sedili addizionale
Istruzioni di montaggio e d’uso . . . . . . . . .67
In te bouwen stoelverwarming
Montagehandleiding en
gebruiksaanwijzing . . . . . . . . . . . . . . . . . . .79
Sædevarme til eftermontering
Monterings- og betjeningsvejledning. . . . 90
Stolvärmeanordning för montering
i efterhand
Monterings- och bruksanvisning . . . . . . . 101
Ettermonterbar setevarmer
Monterings- og bruksanvisning. . . . . . . . 112
Jälkikäteen asennettava
istuinlämmitys
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 123
Встраиваемый комплект обогрева
сидений
Инструкция по монтажу и эксплуатации 134
System podgrzewania foteli do
montażu
Instrukcja montażu i obsługi. . . . . . . . . . . 145
Vyhrievanie sedadla určené pre
dodatočnú montáž
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 157
Vestavné vyhřívání sedadla
Návod k montáži a obsluze . . . . . . . . . . . 168
Utólag beszerelhető ülésfűtés
Szerelési és használati útmutató . . . . . . . 179
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
DRIVING SUPPORT
MAGICCOMFORT
MSH300--IO-16s.book Seite 1 Donnerstag, 13. Juli 2017 10:28 10
MSH300--IO-16s.book Seite 2 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
3
1 2 3
4
9
6
8
5
7
10 11
12
13 14
15
1
MSH300--IO-16s.book Seite 3 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
4
2
3
1
1
2
2
4
5
3
4
30 –
35 cm
6
5
MSH300--IO-16s.book Seite 4 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
5
9
8
7
b
a
0
de
d
c
g
f
MSH300--IO-16s.book Seite 5 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
6
bk
bk
bk
bu
bu
5 A
(31)
RL
og
rd
15 A
+12 V (15)
+12 V (30)
MSH300
h
MSH300--IO-16s.book Seite 6 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
7
EN DE FR ES PT IT NL DA SV
bu Blue Blau Bleu Azul Azul Blu Blauw Blå Blå
og Orange Orange Orange Naranja Cor de laranja Arancione Oranje Orange Orange
rd Red Rot Rouge Rojo Vermelho Rosso Rood Rød Röd
bk Black Schwarz Noir Negro Preto Nero Zwart Sort Svart
NO FI RU PL SK CS HU
bu Blå Sininen Синий Niebieski Modrá Modrá Kék
og Oransje Oranssi Оранжевый Pomarańczowy Oranžová Oranžová Narancs
rd Rød Punainen Красный Czerwony Červená Červená Piros
bk Svart Musta Черный Czarny Čierna Černá Fekete
bk
5 A
(31)
og
rd
15 A
+12 V (15)
+12 V (30)
bu
bu
RL
MSH301
i
MSH300--IO-16s.book Seite 7 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
8
j
20 mm
k
1
2
l
MSH300--IO-16s.book Seite 8 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
9
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
6 Installing the seat heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
7 Using the seat heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
8 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
9 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
10 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
MSH300--IO-16s.book Seite 9 Donnerstag, 13. Juli 2017 10:28 10
Explanation of symbols MSH300, MSH301
10
1 Explanation of symbols
!
A
I
2 Safety and installation instructions
Please observe the prescribed safety instructions and stipulations from the
vehicle manufacturer and service workshops.
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and excess voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
A
NOTICE!
To prevent the risk of short circuits, always disconnect the negative
terminal of the vehicle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be
disconnected.
!
WARNING!
Inadequate supply cable connections could result in short circuits, which
could have as a consequence that:
Cable fires occur
The airbag is triggered
Electronic control devices are damaged
Electric functions fail (indicators, brake light, horn, ignition, lights)
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
MSH300--IO-16s.book Seite 10 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301 Safety and installation instructions
11
Please observe the following instructions:
When working on the following cables, only use insulated cable lugs, plugs and
flat push-on receptacles:
30 (direct supply from positive battery terminal)
15 (connected positive terminal, behind the battery)
31 (return cable from the battery, earth)
Do not use terminal strips.
The safest type of connection is to solder the ends of the cables together and
then insulate them.
Only use insulated cable terminals, plugs and flat sockets for releasable
connections. Do not use crimp terminals (cable connectors) or terminal strips.
Use a crimping tool (fig. 1 10, page 3) to connect the cables.
When connecting to cable 31 (earth), screw the cable
To the vehicle's earth bolt with a cable lug and a gear disc or
To the sheet-metal bodywork with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
If you disconnect the negative terminal of the battery, all data stored in the volatile
memories will be lost.
The following data must be set again, depending on the vehicle equipment
options:
–Radio code
Vehicle clock
–Timer
On-board computer
Seat position
You can find instructions for making these settings in the appropriate operating
instructions.
Observe the following installation instructions:
Secure the parts installed in the vehicle in such a way that they cannot become
loose under any circumstances (sudden braking, accidents) and cause injuries
to the occupants of the vehicle.
To prevent damage, when drilling ensure that there is sufficient space on the
other side for the drill head to come out (fig. 2, page 4).
Deburr all drill holes and treat them with a rust-protection agent.
MSH300--IO-16s.book Seite 11 Donnerstag, 13. Juli 2017 10:28 10
Safety and installation instructions MSH300, MSH301
12
Observe the following instructions when working with electrical parts:
When testing the voltage in electrical cables, only use a diode test lamp
(fig. 1 8, page 3) or a voltmeter (fig. 1 9, page 3).
Test lamps with an illuminant (fig. 1 12, page 3) take up voltages which are too
high and which can damage the vehicle's electronic system.
When making electrical connections (fig. 3, page 4), ensure that
They are not kinked or twisted
They do not rub on edges
They are not laid in sharp-edged ducts without protection.
Insulate all connections.
Secure the cables against mechanical wear with cable binders or insulating tape,
for example to existing cables.
Observe the following instructions when using the seat heater:
Do not place any sharp or heavy objects on the seat, as the seat heater could
otherwise be damaged.
Persons with an impaired sensitivity to heat should only operate the seat heating
on level 1.
Do not place any heat insulating objects, such as blankets or coats, on the seat
when the seat heater is switched on.
The seat heater can be damaged by fluids spilt on the seat.
Never switch the seat heater on when it is wet.
MSH300--IO-16s.book Seite 12 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301 Scope of delivery
13
3Scope of delivery
4 Intended use
The MagicComfort seat heating MSH300 (ref. no. 9600000395) and
MSH301 (ref. no. 9600000396) are suitable for installation in the front vehicle seats
of passenger vehicles, transporters and caravans.
A
No. in
fig. 4, page 4
Quantity Designation Ref. no.
MSH300 MSH301
1 2 1 Seat surface heating element 9101700038
2 2 1 Backrest heating element 9101700039
3 2 1 Switch 9101700041
4 1 1 Set of connecting cables
(black: right side
blue: left side)
9101700053
5 1 1 Switchbox 9101700051
1 1 Drill template
12 6 Double-sided adhesive tape
12 6 Insulating material
1 1 Operating manual
NOTICE!
For vehicles equipped with side airbags in the seat backrests, seat
occupancy detection or child seat detection, observe the vehicle
manufacturer's specifications.
MSH300--IO-16s.book Seite 13 Donnerstag, 13. Juli 2017 10:28 10
Technical description MSH300, MSH301
14
5 Technical description
The heating elements for the MagicComfort seat heating MSH300 and MSH301
can be installed in the driver’s seat and in the passenger seat.
The shape of the seat is not altered by the heating elements.
The seat heater is operated using a switch.
6 Installing the seat heater
6.1 Tools required (fig. 1, page 3)
For installation and assembly you will need the following tools:
Drill bit set (1)
Drill (2)
Screwdriver (3)
Set of ring or open-ended spanners (4)
Measuring ruler (5)
Hammer (6)
Centre punch (7)
To make and test the electrical connection, the following tools are required:
Diode test lamp (8) or voltmeter (9)
Crimping tool (10)
Insulating tape (11)
Hot air blower (13)
Soldering iron (14)
Solder (15)
Cable bushing sleeves (if necessary)
To fasten the cables you may require additional cable binders.
MSH300--IO-16s.book Seite 14 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301 Installing the seat heater
15
6.2 Installing the seat heater
Removing the seat
Secure the vehicle against rolling away.
A
Check the suitability for installation using these installation instructions and the
manufacturer's information.
Remove the fastening screws from the vehicle seat.
Lift the seat out of the vehicle.
Preparing the seat
Remove all plastic panelling from the seat to ensure the fastening of the cover
fabric can be reached.
Separate the backrest from the seat (fig. 7, page 5 and fig. 8, page 5).
Open the seat cover on the seat surface.
The cover fabric is usually tucked into a seam on the frame with a wide cardboard
strip or metal wire.
Remove the fasteners using a screwdriver and pliers (fig. 9, page 5 and fig. 0,
page 5).
Remove any upholstery staples or cross braces (fig. a, page 5).
Open the cover of the backrest in the same way.
NOTICE!
For vehicles with side air bags in the seat backrest, observe the
manufacturer's instructions on removing the seats and the upholstery.
MSH300--IO-16s.book Seite 15 Donnerstag, 13. Juli 2017 10:28 10
Installing the seat heater MSH300, MSH301
16
Preparing the heating elements
A
I
Place the heating elements on the seat and backrest.
If there are anchoring grooves in the seat or the backrest, mark these areas on the
heating elements.
Mark the required lengths. Take into account the depth of the anchoring
grooves, if present. The heating element is inserted in these anchoring grooves.
Trim the heating element to the required length.
Customise the cut-out sections as required.
Insulate all the trimmed ends with the insulating material.
NOTICE!
Insulate all the trimmed ends with the insulating material supplied to
prevent a short circuit.
NOTE
You can cut the heating elements to the required length and shorten
the lengths of the two conductor paths.
You can cut out a section of the heating element in the area of the
anchoring grooves on the seat or the backrest. Make sure the cut-out
sections are only made between the two black seams (fig. 5,
page 4).
Do not cut the mat lengthways, otherwise it will not be heated in the
area of the incision (fig. 5, page 4).
The heating surface on the backrest only needs to extend approx.
30 – 35 cm above the seat, as the driver only leans against this area
when sitting normally (fig. 6, page 4).
MSH300--IO-16s.book Seite 16 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301 Installing the seat heater
17
Installing the heating element for the seat surface
Insert the heating element for the seat surface between the cover fabric and the
foam core of the seat (fig. b, page 5).
If anchoring grooves are present, make sure that the cut-out sections are
positioned over the anchoring grooves (fig. c, page 5) and place the heating
elements in the anchoring grooves.
Fasten the heating element using double-sided adhesive tape to prevent it
sliding on the foam core.
Ensure that no creases or kinks form.
Installing the heating element for the backrest
A
Open the lower area of the backrest cover (fig. d, page 5).
Push the heating element into the gap between the seat cover and the seat
cushion (fig. e, page 5).
Fasten the heating element using double-sided adhesive tape to prevent
creases.
Installing the seat
Reassemble the backrest and seat.
Lift the seat into the vehicle.
Secure the vehicle seat with the fastening screws.
NOTICE!
If the seats are equipped with side airbags, then there is a
predetermined breaking point in the cover fabric. The seat cover must
therefore not be pulled tightly or slip out of place.
MSH300--IO-16s.book Seite 17 Donnerstag, 13. Juli 2017 10:28 10
Using the seat heater MSH300, MSH301
18
Electrical connection
MSH300
The complete circuit diagram can be found in fig. h, page 6.
MSH301
The complete circuit diagram can be found in fig. i, page 7.
A
Attach the switchbox to a suitable location in the vicinity of the dashboard
(fig. j, page 8).
Find a suitable place for installing the seat heater switch.
If possible, use the blanking plugs provided for this purpose.
Ensure that there is enough room behind the panel for the installation of the
switch.
Mark the switch cut-out using the template provided (fig. k, page 8).
Cut out the marked area with an appropriate tool.
Install the switch into the cut-out (fig. f, page 5).
Install the ready-made wiring harness so that the cables cannot bend or fray
(fig. g, page 5).
7 Using the seat heater
I
Press the seat heater switch to turn on the seat heater:
Press once: Level 3 (high heat output)
Press twice: Level 2 (medium heat output)
Press three times: Level 1 (low heat output)
One, two or three LEDs (fig. l 2, page 8) on the switch light up in red.
To switch the seat heating off: Press the switch until the LEDs (fig. l 2, page 8)
on the switch go out.
NOTICE!
Ensure it has been securely fitted, particularly in the area of the seat rails.
NOTE
The seat heating logo (fig. l 1, page 8) also lights up when the seat
heating is switched on.
MSH300--IO-16s.book Seite 18 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301 Guarantee
19
8Guarantee
The statutory warranty period applies. If the product is defective, please contact the
manufacturer's branch in your country (see the back of the instruction manual for the
addresses) or your retailer.
For repair and guarantee processing, please include the following documents when
you send in the device:
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
9Disposal
Place the packaging material in the appropriate recycling waste bins wherever
possible.
M
If you wish to finally dispose of the product, ask your local recycling centre
or specialist dealer for details about how to do this in accordance with the
applicable disposal regulations.
10 Technical data
MagicComfort MSH300 MagicComfort MSH301
Ref. no.: 9600000395 9600000396
Operating voltage: 12 Vg
Power: adjustable to three levels, with 10 – 70 W per seat
Max. power consumption: 10 A 5 A
Dimensions: Seat element: 580 x 270 mm
Backrest element: 580 x 270 mm
MSH300--IO-16s.book Seite 19 Donnerstag, 13. Juli 2017 10:28 10
MSH300, MSH301
20
Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig
durch und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe
des Produktes an den Nutzer weiter.
Inhaltsverzeichnis
1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2 Sicherheits- und Einbauhinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6 Sitzheizung montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7 Sitzheizung benutzen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8 Gewährleistung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
MSH300--IO-16s.book Seite 20 Donnerstag, 13. Juli 2017 10:28 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192

Dometic MAGICCOMFORT MSH300 Mode d'emploi

Taper
Mode d'emploi