Delta Faucet T14159-CZ Manuel utilisateur

Marque: Delta Faucet

Modèle: T14159-CZ

Catégorie: Articles sanitaires

Taper: Manuel utilisateur

Owners Manual

13/14 Series

Write purchased model number here.

Table of Contents:

Warranties ..................................................................................Page 2

Installation Instructions ............................................................... Pages 3 - 12

Clean and care ...........................................................................Page 12

Maintenance ............................................................................... Page 12

Cartridge Summary Reference Sheet ........................................Page 13

For additional replacement parts, visit www.deltafaucet.com

CAUTION: This system/device must be set by the

installer to ensure safe, maximum temperature.

Any change in the setting may raise the discharge

temperature above the limit considered safe and

may lead to hot water burns.

NOTICE TO INSTALLER: CAUTION! – As the

installer of this valve, it is your responsibility

to properly INSTALL and ADJUST this valve

per the instructions given. This valve does

not automatically adjust for inlet temperature

changes, therefore, someone must make the

necessary Rotational Limit Stop adjustments

at the time of installation and further adjustments

may be necessary due to seasonal water

temperature change. YOU MUST inform the

owner/user of this requirement by following the

instructions. If you or the owner/user are unsure

how to properly make these adjustments please

refer to page 6 and if still uncertain, call us at

1-800-345-DELTA.

After installation and adjustment, you must ax

your name, company name and the date you

adjusted the Rotational Limit Stop to the caution

label provided and apply or attach the label to

the back side of the closest cabinet door and

the warning label to the water heater. Leave

this Instruction Sheet for the owner’s/user’s

reference.

WARNING: This pressure balanced or

thermostatic bath valve is designed

to minimize the eects of outlet water

temperature changes due to inlet pressure

changes, commonly caused by dishwashers,

washing machines, toilets and the like. It may

not provide protection from hot water burns

when there is a failure of other temperature

controlling devices elsewhere in the plumbing

system, if the rotational limit stop is not

properly set or if the hot water temperature is

changed after the settings are made or if the

water inlet changes due to seasonal changes.

WARNING: Do not install a shut-o device on

either outlet of this valve. When this type of

device shuts o the water ow, it can defeat

the ability of the valve to balance the hot and

cold water pressures.

107528 Rev. D10/20/2020

107528

MultiChoice

Valve Trim

Installation Instructions

You May Need

13/14 Series 13/14 Series 13/14 Series

X00107528

107528 Rev. D

Delta HDF Limited Warranty

All parts of the Delta HDF faucet are warranted to the

original consumer purchaser to be free from defects in

material and workmanship for a period of ve (5) years.

This warranty is made to the original consumer purchaser

and shall be eective from date of purchase as shown on

purchaser’s receipt.

Delta will replace, FREE OF CHARGE, during the warranty

period, any part which proves defective in material and/or

workmanship under normal installation, use and service.

Replacement parts can be obtained from your local

dealer or distributor listed in the telephone directory or by

returning the part along with the purchaser’s receipt to our

factory, TRANSPORTATION CHARGES PREPAID, at the

address listed. THIS WARRANTY IS THE ONLY EXPRESS

WARRANTY MADE BY DELTA. ANY CLAIMS MADE

UNDER THIS WARRANTY MUST BE MADE DURING

THE FIVE YEAR PERIOD REFERRED TO ABOVE. ANY

IMPLIED WARRANTIES, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO

THE DURATION OF THIS WARRANTY. LABOR CHARGES

AND/OR DAMAGE INCURRED IN INSTALLATION, REPAIR

OR REPLACEMENT AS WELL AS INCIDENTAL AND

CONSEQUENTIALDAMAGES CONNECTED THEREWITH

ARE EXCLUDED AND WILL NOT BE PAID BY DELTA.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion or limitation of incidental

or consequential damages, so the above limitations or

exclusions may not apply to you.

This warranty gives you specic legal rights, and you may

also have other rights which vary from state to state.

This warranty is void for any damage to this faucet due to

misuse, abuse, neglect, accident, improper installation, any

use violative of instructions furnished by us or any use of

replacement parts other than genuine Delta parts.

Parts and Finish. All parts (other than electronic parts and batteries) and finishes of Delta® faucets purchased from authorized Delta sellers are warranted to the original

consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first

installed. For commercial purchasers, (a) the warranty period is ten (10) years for multi-family residential applications and (b) five (5) years for all other commercial

applications, in each case from the date of original purchase. For purposes of this warranty, the term “multi-family residential application” refers to the purchase of the

faucet from an authorized Delta seller by a purchaser who owns but does not live in the residential dwelling in which the faucet is initially installed, such as in a rented or

leased single unit or multi-unit detached home (duplex or townhome), or a condominium, apartment building or community living center. The following installations are not

considered multi-family residential applications, are excluded from the 10-year warranty and are subject to the 5-year warranty: industrial, institutional or other business

premises, such as a dormitory, hospitality premises (hotel, motel or extended stay location), airport, educational facility, long- or short-term healthcare facility (hospital,

rehabilitation center, nursing, assisted or staged-care living unit), public space or common area.

Parts and Finish for Delta® Recertified Faucets. Delta Faucet Company offers for sale on deltafaucet.com Delta® Recertified faucets. All parts (other than electronic

parts and batteries) and finishes of these Delta® Recertified faucets are warranted to the original consumer purchaser to be free from defects in material and workmanship

for ten (10) years from the date of original purchase. For commercial purchasers, the warranty period is one (1) year from the date of original purchase.

Electronic Parts. Electronic parts (other than batteries), if any, of Delta® faucets purchased from deltafaucet.com or authorized Delta sellers are warranted to the original

consumer purchaser to be free from defects in material and workmanship for five (5) years from the date of original purchase or, for commercial purchasers, for one (1)

year from the date of original purchase. No warranty is provided on batteries.

What We Will Do. Delta Faucet Company will repair or replace, free of charge, during the applicable warranty period (as described above), any part or finish that proves

defective in material and/or workmanship under normal installation, use and service. If repair or replacement is not practical, Delta Faucet Company may elect to refund

the purchase price in exchange for the return of the product. These are your exclusive remedies.

What Is Not Covered. Because Delta Faucet Company is unable to control the quality of Delta products sold by unauthorized sellers, unless otherwise prohibited by law,

this warranty does not cover Delta products purchased from unauthorized sellers.

Any labor charges incurred by the purchaser to repair, replace, install or remove this product are not covered by this warranty. Delta Faucet Company shall not be liable

for any damage to the faucet resulting from reasonable wear and tear, outdoor use, misuse (including use of the product for an unintended application), freezing water,

abuse, neglect or improper or incorrectly performed installation, maintenance or repair, including failure to follow the applicable care and cleaning instructions. Delta Faucet

Company recommends using a professional plumber for all installation and repair of faucets. We also recommend that you use only genuine Delta® replacement parts.

What You Must Do To Obtain Warranty Service or Replacement Parts. A warranty claim may be made and replacement parts may be obtained by calling 1 800 345

DELTA (3358) or by contacting us by mail or online as follows (please include your model number and date of original purchase):

In the United States and Mexico: In Canada:

Delta Faucet Company Masco Canada Limited, Plumbing Group

Product Service Technical Service Centre

55 E. 111th Street 350 South Edgeware Road

Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1

Attention: Warranty Service Attention: Warranty Service

www.deltafaucet.com/service-parts/contact-us http://www.deltafaucet.ca/customersupport/assistance.html

Proof of purchase (original sales receipt) from the original purchaser must be made available to Delta Faucet Company for all warranty claims unless the purchaser has

registered the product with Delta Faucet Company or the product is a Delta® Recertified product purchased from deltafaucet.com. This warranty applies only to Delta®

faucets manufactured after January 1, 2019 and installed in the United States of America, Canada and Mexico.

Limitation on Duration of Implied Warranties. Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty

lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION

OF THIS WARRANTY, WHICHEVER IS SHORTER.

Limitation of Special, Incidental or Consequential Damages. Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of

special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE

LAW, THIS WARRANTY DOES NOT COVER, AND DELTA FAUCET COMPANY SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. DELTA FAUCET COMPANY SHALL NOT BE LIABLE FOR ANY DAMAGE

TO THE FAUCET RESULTING FROM REASONABLE WEAR AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED

APPLICATION), FREEZING WATER, ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED INSTALLATION, MAINTENANCE OR REPAIR,

INCLUDING FAILURE TO FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to residents of the State of New Jersey: The

provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey.

Additional Rights. This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.

This is Delta Faucet Company’s exclusive written warranty and the warranty is not transferable.

If you have any questions or concerns regarding our warranty, please contact us as provided above or view our Warranty FAQs at www.deltafaucet.com.

Limited Warranty on Delta

Faucets

107528 Rev. D

MultiChoice

Rough-In Installation

(When your product requires)

SHUT OFF WATER SUPPLIES.

Consider the type and thickness of your

finished wall before placing your stringer

back plate.

• Install the body (1) so the surface of the

finished wall is flush with the front of the

plasterguard (2) ± 3/8". Note: For

models with stops (3), plasterguard

must be flush or subflush 3/8" to

finished wall.

• Mount body using the two stringer

mounting holes (4) on the bracket.

• Make sure the word “UP” (5) is on top of

the valve body when installing.

Distance (1) from the stringer (2) to the

front of the plasterguard is 2.8" (71 mm).

If a thin wall is used, be sure to have the

plasterguard behind the wall, otherwise

the wall should always be flush with the

front of the plasterguard. See instruction

on the bag for thin wall mounting.

107528 Rev. D

• Connect valve body to water supplies using

the proper fittings for your valve body type

(copper tubing, iron pipe or Pex). Note: (1)

is the cold inlet port and (2) is the hot

inlet port.

• If either of the two outlet ports is to be

unused, seal the port with a pipe plug.

• Remove bonnet (1).

NOTICE: Avoid soldering at high

temperatures. Components of the rough

could become damaged.

• Be sure stops (2) are removed from the

w/stops version before soldering. Do not

install stops before soldering.

If you are making a BACK TO BACK

OR REVERSE INSTALLATION (hot on

right and cold on left) install the valve

body as described, but the water supply

lines will be reversed. Note: (1) is the

hot inlet port and (2) is the cold inlet

port.

Copper Tubing Iron Pipe

Pex

107528 Rev. D

• Connect top outlet (1) to shower pipe with

proper fittings.

• Connect bottom outlet (2) to tub spout pipe

with proper fittings.

• Pipe (3) between valve body and tub spout

must be a minimum of 1/2" (13 mm) copper

pipe or 1/2" (13 mm) iron pipe in a straight

drop no less than 8" (203 mm) but no more

than 18" (457 mm) long with only one iron

pipe or copper 90 degree elbow to the tub

spout nipple. Do not use PEX tubing for tub

spout drop.

• To flush the system of debris, remove bonnet nut

(1).

• Prepare the area for water spray.

• Slowly turn on the water supplies to purge the

system for 30 seconds.

• After flushing, install the cartridge and bonnet nut.

• Turn cartridge stem counter clockwise until it

stops.

FOR MODELS WITH STOPS, install the

stops but leave them full open. Install stops as

follows:

• Thread nut (2) onto stem (3) as shown. Then

press stem and nut assembly into body and

tighten using a 3/8”,6 point, deep well socket.

With a flat head screwdriver, adjust stem

clockwise to close and counterclockwise to

open.

• Plug the tub spout and/ or shower outlet(s)

with the appropriate fitting for your piping.

• Test for leaks.

• After testing, turn off the valve by rotating the

cartridge stem fully clockwise.

PRESSURE TESTING & FLUSHING THE

INSTALLATION

107528 Rev. D

Cartridge Installation

Turn off water supplies. Remove bonnet

nut (1) and test cap (2) from the body. If

this is not a thin wall mounting, the entire

plasterguard (3) may be removed. If screen

(4) is in place, remove before installing

cartridge.

Back to back Installation C.

For back to back or reverse installations

(hot on right and cold on left) insert the

cartridge with the “hot side” on the right.

If you are not making a reverse or back

to back installation skip this step and

continue with step 2C.

Slide bonnet nut (1) over the cartridge

and thread onto the body. Hand tighten

securely.

Normal Installation (changes not required)

Reverse

Installation

Cold

Hot

Rotate valve cartridge (1) so the words

“HOTTER COLDER” (2) appear on the top.

Insert cartridge assembly into rough-in body.

A light coating of plumbers grease applied to

o-rings may aid in assembly. Make sure the

key (3) on the cartridge is fully engaged with

the slot in the brass body (4).

107528 Rev. D

58045

Shower Head and Tub Spout Installation

FOR SHOWER HEAD INSTALLATION: Connect top

outlet (1) to shower arm (2) with proper ttings. To

prevent damage to nish on shower arm, insert wall end

of shower arm into shower ange (3) before screwing

arm into riser connection. Thread shower head (4) onto

shower arm. Apply plumber tape to pipe threads on both

ends. Do not overtighten shower head.

B-1

B-1: To combine the two showers, insert the top tab (1) on the hand shower into the slot (2) of

the shower head. Push the hand shower into the shower head until the two parts snap together.

B-2: To combine the two showers, push the hand shower into the shower head, then pull down

on the hand shower until locked with the shower head.

If the shower head moves when removing the hand shower, hand tighten the connection between

the shower head and the shower arm.

To change spray modes, turn the lever (3) left or right to the desired setting. Turn knob (4) to

change between shower head only, shower head and hand shower or hand shower only.

B-2

Installation

107528 Rev. D

FOR TUB SPOUT INSTALLATION:

Refer to the installation instructions supplied with your spout. Do not connect deck mount spouts to

in-wall valves. Do not use hand showers connected in lieu of a tub spout to a tub/shower valve. Do not

use PEX tubing for tub spout drop.

107528 Rev. D

IMPORTANT:

The Rotational Limit Stop is used to limit the

amount of hot water available such that, if set

properly, the user will not be scalded if the

handle accidentally is rotated all the way to “hot”

when a person is showering or lling a tub. The

rst position allows the LEAST amount of hot

water to mix with the cold water in the system.

In the rst position the water will be the coldest

possible when the handle is turned all the way

to hot. As you move the Rotational Limit Stop

counterclockwise, you progressively add more

and more hot water in the mix. The last position

to the left will result in the greatest amount of hot

water to the mix, and the greatest risk of scald

injury if someone accidentally turns the valve

handle all the way to the hot side while showering

or lling a tub.

WARNING: In some instances, setting the

Rotational Limit Stop in the hottest position

(full counterclockwise) could result in scald

injury. It is necessary to adjust the Rotational

Limit Stop so that the water coming out of the

valve will not scald the user when the handle

of the valve is rotated to the hot side.

• According to the majority of industry standards,

the maximum allowable temperature of the water

exiting the valve is 120°F (Your local plumbing

codes may require a water temperature less than

120°F).

• The Rotational Limit Stop may need to be re-

adjusted seasonally if the inlet water temperature

changes. For example, during the winter, the

cold water temperature is colder than it is

during the summer which could result in varying

outlet temperatures. A water temperature for

a comfortable bath or shower is typically

between 90°F - 110°F.

• Run the water so that the cold water is as

cold as it will get and hot water is as hot as

it will get. Place the handle on the stem (see

page 8, step 4C) and rotate the handle coun-

terclockwise until the handle stops.

• Place a thermometer in a plastic tumbler

and hold in the water stream. If the water

temperature is above 120°F, the Rotational

Limit Stop must be repositioned clockwise to

decrease valve outlet water temperature to

less than 120°F or to meet the

requirements of

your local plumbing codes.

• To adjust the temperature of the water

coming out of the valve, pull the disc back

to a position where it is possible to remove

the Rotational Limit Stop and readjust the

teeth

engagement position to the desired

temperature. Clockwise will decrease the

outlet temperature, counterclockwise will

increase the outlet temperature. Temperature

change per tooth (notch) could be 4° - 16°F

based on inlet water conditions. Repeat as

necessary. Push disc until fully seated.

WARNING: Failure to re-install Disc after

setting Rotational Limit Stop could result

in scald injury.

• MAKE SURE COLD WATER FLOWS

FROM THE VALVE FIRST. MAKE SURE

WATER FLOWING FROM THE VALVE AT

THE HOTTEST FLOW POSSIBLE DOES

NOT EXCEED 120°F OR THE MAXIMUM

ALLOWED BY YOUR LOCAL PLUMBING

CODE.

Adjusting the Rotational Limit Stop

Hotter

Disc

Stem

1st Position

-For RLS With Removable Disc

107528 Rev. D

IMPORTANT:

The Rotational Limit Stop is used to limit the

amount of hot water available such that, if set

properly, a scald injury is less likely to occur if the

handle accidentally is rotated all the way to “hot”

when a person is showering or lling a tub. The

rst position allows the LEAST amount of hot

water to mix with the cold water in the system.

In the rst position the water will be the coldest

possible when the handle is turned all the way

to hot. As you move the Rotational Limit Stop

counterclockwise, you progressively add more

and more hot water in the mix. The last position

to the left will result in the greatest amount of hot

water to the mix, and the greatest risk of scald

injury if someone accidentally turns the valve

handle all the way to the hot side while showering

or lling a tub.

WARNING: In some instances, setting the

Rotational Limit Stop in the hottest position

(full counterclockwise) could result in scald

injury. It is necessary to adjust the Rotational

Limit Stop so that the water coming out of the

valve will not scald the user when the handle

of the valve is rotated to the hot side.

• According to the majority of industry standards,

the maximum allowable temperature of the water

exiting the valve is 120°F (Your local plumbing

codes may require a water temperature less than

120°F).

• The Rotational Limit Stop may need to be re-

adjusted seasonally if the inlet water temperature

changes. For example, during the winter, the

cold water temperature is colder than it is

during the summer which could result in varying

outlet temperatures. A water temperature for

a comfortable bath or shower is typically

between 90°F - 110°F.

• Run the water so that the cold water is as

cold as it will get and hot water is as hot as

it will get. Place the handle on the stem (see

page 8, step 4C) and rotate the handle coun-

terclockwise until the handle stops.

• Place a thermometer in a plastic tumbler

and hold in the water stream. If the water

temperature is above 120°F, the Rotational

Limit Stop must be repositioned clockwise to

decrease valve outlet water temperature to

less than 120°F or to meet the

requirements of

your local plumbing codes.

• To adjust the temperature of the water

coming out of the valve, pull the white

Rotational Limit Stop (1) outward and rotate.

Clockwise rotation will decrease the outlet

temperature, counterclockwise rotation will

increase the outlet temperature. Temperature

change per tooth (notch) could be 4° - 16°F

based on inlet water conditions. Repeat as

necessary. When nished, make sure that the

Rotational Limit Stop is fully retracted into the

seated position. WARNING: Do not take the

Rotational Limit Stop apart.

• MAKE SURE COLD WATER FLOWS

FROM THE VALVE FIRST. MAKE SURE

WATER FLOWING FROM THE VALVE AT

THE HOTTEST FLOW POSSIBLE DOES

NOT EXCEED 120°F OR THE MAXIMUM

ALLOWED BY YOUR LOCAL PLUMBING

CODE.

Hotter

Cooler

-For RLS With Pull/Turn Adjustment

RLS with pull/turn adjustment

107528 Rev. D

Trim Installation

Slide O-ring (1) over cartridge and the

bonnet nut (2). The O-ring, which acts as

a spacer to steady the sleeve, should rest

behind the bonnet nut.

If your model requires a spacer (3), insert

it into the sleeve (4) and push it to the

front. Slide the sleeve over the cartridge,

body and O-ring.

Using an Allen wrench to secure the set

screw (1), install the handle (2) onto the

stem and tighten set screw. Insert plug

button (3) (if your model has one) into

set screw hole. Adjust the sleeve (4) to

minimize the gap between the sleeve &

handle.

Note: Adust for up to 1" thick wall. For thick

wall installation, visit delta faucet website,

check "view technical specication" of the

models you bought, order the appropriate

thick wall installation kit RP to get additional

1 3/4" wall thickness.

B-1: Secure the escutcheon (1) and backplate

(2) (if your model has one) to the bracket

(3) using the 2 screws (4) provided. Do not

overtighten escutcheon screws. Press the

cover (5) onto the escutcheon (1) when your

product includes the cover.

B-2: Install bracket (5) over the cartridge

body using the 2 screws (6) provided. Install

escutcheon (7) by placing it over the bracket

as shown and rotating it to lock the tabs (8).

Secure the escutcheon to the bracket using set

screw (9).

C-1

B-1

B-2

107528 Rev. D

Clean and Care

Care should be given to the cleaning

of this product. Although its nish is

extremely durable, it can be damaged by

harsh abrasives or polish. To clean, simply

wipe gently with a damp cloth and blot dry

with a soft towel.

Warning: Scrubbing Bubbles

Bathroom

Cleaner and Lysol

Basin Tub and Tile

Cleaner must not be used on the clear knob

handles and levers. Use of these cleaners

can result in cracked or severely damaged

handles. If overspray gets onto the handles,

immediately wipe them dry with a soft

cotton cloth.

Maintenance

Faucet leaks from tub spout/shower head:

SHUT OFF WATER SUPPLIES.

Replace seats and springs–Repair

Kit RP4993. Check condition of lower O-rings and

replace if necessary RP14414. See Helpful Hints 1,

2, & 3.

If leak persists:

SHUT OFF WATER SUPPLIES.

Replace valve cartridge RP46074.

See Helpful Hints 1, 2, 3, 4 & 5

Unable to maintain constant

water temperature:

Replace housing assembly with RP46074 or follow

instructions in Helpful Hints 1, 2, 3, 4 & 5.

Helpful Hints:

1. Before removing valve cartridge assembly for any

maintenance, be sure to note the position of the

rotational limit stop on the cap. The valve cartridge

assembly must always be put back in the same

position. BE SAFE! After you have nished the

installation, turn on valve to make sure COLD

WATER FLOWS FIRST.

2. To remove valve cartridge from body, shut o

water supplies and remove handle and bonnet nut.

Do not pry the valve cartridge out of the body with

a screwdriver. Place handle on stem and rotate

counterclockwise approximately 1/4 turn after the

stop has been contacted. Lift valve cartridge out

of body.

3. To remove seats and springs.

Remove valve cartridge. Separate cap assembly

from the housing assembly by rotating the cap

assembly counterclockwise 90 o (degrees).

Separate cap and housing assemblies.

4. If the water in your area has lime, rust, sand

or other contaminants in it, your pressure

balance valve will require periodic inspection.

The frequency of the inspection will depend

on the amount of contaminants in the water. To

inspect valve cartridge remove it and follow the

steps in note 1 above. Turn the valve to the full

mix position and shake the cartridge vigorously.

If there is a rattling sound, the unit is functional

and can be reinstalled following instructions given

in note 1 above. If there is no rattle, replace the

housing assembly with the proper RP.

5. Push disc until fully seated. See page 9 for

more details

Install adapter (1) on cartridge stem (6) with

screw (2).

Thread set screw (4) into handle (3) slightly,

put handle (3) on adapter (1) , hold and adjust

the handle (3) at OFF position to ensure it

well aligned with sleeve (7). Then tighten set

screw (4).

Apply pressure, insert button (5) until properly

seated. Adjust the sleeve (7) to minimize the

gap between the sleeve & handle.

C-2

107528 Rev. D

Cartridge Summary Reference Sheet

Monitor

Series 1300/1400

Cartridge shipped before March 2006.

Cartridge shipped in July 2006 and after

(prior to MultiChoice

transition).

Shorter lower

housing

Blue or

o-white

White

Shorter lower

housing

White

Blue

Order RP19804 to replace cartridge. Order RP19804 to replace cartridge.

MultiChoice

13/14

Cartridge shipped from March 2006 to August 2014. Cartridge shipped in August 2014 and after.

Longer lower

housing

Grey

O-white

Longer lower

housing

Grey

O-white

Order RP46074 to replace cartridge. Order RP46074 to replace cartridge.

NOTE: A running change for MultiChoice

13/14 valves began August 2014, and

features a new Rotational Limit Stop.

MultiChoice

13/14 (Ceramic)

Cartridge shipping in select models (-CER).

Grey

White

Order RP74236 to replace cartridge.

107528 Rev. D

Instrucciones para la

Instalación del Accesorio

para Válvulas MultiChoice

Manual para los

Propietarios

13/14 Series

Escriba aquí el número del modelo comprado.

Usted puede necesitar

Contenido:

Garantías ....................................................................................Page 2

Instrucciones de Instalación .......................................................Pages 3 - 12

Limpieza y Cuidado de su Liave.................................................Page 12

Mantenimiento ............................................................................ Page 12

Hoja resumen de referencia para el cartucho ............................Page 13

Para las piezas de repuesto adicionales, visite www.deltafaucet.com

Límite Rotacional y aplicar o jar la etiqueta al

dorso de la puerta del gabinete más cercano y la

etiqueta de aviso al calentador de agua. Deje la

Hoja de Instrucciones para referencia del dueño/

usuario.

ADVERTENCIA: Esta válvula de presión

balanceada y termostática está diseñada

para minimizar los efectos de los cambios de

temperatura de agua por causa de los cambios

de presión en el agua de entrada, comúnmente

causados por lavadoras de platos, lavadoras

de ropa, inodoros, y otros aparatos por el

estilo. Puede no proporcionar protección de

quemaduras de agua caliente cuando hay

alguna falla de otros aparatos para el control

de temperatura en otro sitio en el sistema de

plomería. También no proporcionará protección

si el tope del límite rotacional la temperatura

no está apropiadamente jo o si cambia la

temperatura del agua caliente después de

hacer los ajustes o si los cambios del gua de

entrada son por los cambios estacionales.

ADVERTENCIA: No instale un aparato de corte

o cierre en cualquiera de las tomas de esta

válvula. Cuando este tipo de aparato cierra el

ujo de agua, puede hacer fallar la habilidad de

la válvula de balancear las presiones del agua

caliente y fría.

El instalador debe apostar este systema/divisa para

garantizar temperatura maximo y seguro. Cualqueir

cambio en el ajuste puede subir la temperatura

del agua de descarga sobre el límite considerado

seguro y puede resultar en quemaduras de agua

caliente.

AVISO PARA EL INSTALADOR:

PRECAUCIÓN – Como instalador de esta

válvula, es su responsabilidad de INSTALAR Y

AJUSTAR apropiadamente esta válvula como

se describe en las instrucciones, por lo tanto,

debe haber una persona para hacer los ajustes

necesarios del Tope del Límite Rotacional y del

pomo para la temperatura en el momento que

se haga la instalación y pueda necesitar ajustes

adicionales por los cambios estacionales de la

temperatura del agua. USTED DEBE informarle

al dueño/usuario sobre este requisito siguiendo

las instrucciones. Si usted o el dueño/usuario

no están seguros como hacer estos ajustes

apropiadamente, por favor reérase al Página

6 y si todavía no está seguro, llámenos al

1-800-345-DELTA.

Después de hacer la instalación y el ajuste,

usted puede agregarle a la etiqueta de aviso

proporcionada, su nombre, el nombre de

lacompañía y la fecha cuando ajustó el Tope del

compañía y la fecha cuando ajustó el Tope del

107528

107528 Rev. D10/20/2020

107528 Rev. D

Garantia Limitada de Delta HDF

Todas las piezas de la llave Delta HDF están

garantizadas al dueño original de estar libres de

defectos en materiales y en la mano de obra por un

período de cinco (5) años. Esta garantía se hace al

dueño original y será efectiva el día de la compra como

se ve en el recibo de compra.

Delta reemplazará, LIBRE DE CARGO, durante el

período de la garantía, cualquier pieza que resulte

defectuosa en materiales y/o en la mano de obra bajo

instalación, uso y servicio normal. Las piezas de

repuesto pueden ser obtenidas de su comerciante o

distribuidor local que se encuentran en la guía telefónica

o si usted devuelve la pieza con el recibo de compra

a nuestra fabrica, Y LOS CARGOS DE TRANSPORTE

PAGADOS CON ANTELACION, a la dirección dada.

ESTA GARANTIA ES LA UNICA GARANTIA EXPRESA

DE DELTA. CUALQUIER RECLAMO HECHO BAJO

ESTA GARANTIA TIENE QUE SER HECHO DURANTE

EL PERIODO DE CINCO AÑOS A QUE SE REFIERE

ARRIBA. CUALQUIER GARANTIA IMPLICITA,

INCLUYENDO LA GARANTIA IMPLICITA DE

COMERCIALIZACION O CONVENIENCIA PARA UN

PROPOSITO PARTICULAR, SON LIMITADOS EN

DURACION A LA DURACION DE ESTA GARANTIA.

LOS CARGOS PARA LA MANO DE OBRA Y/O DAÑOS

INCURRIDOS EN LA INSTALACION, REPARACION O

REEMPLAZO, ASI COMO LOS DAÑOS INCIDENTALES

O CONSECUENTES CONECTADOS CON

ELLOS SON EXCLUIDOS Y NO SERAN PAGADOS

POR DELTA.

Algunos estados no permiten limitaciones al tiempo que

dura la garantía implícita, o la exclusión o limitación de

los daños incidentales o consecuentes, así que la

limitación o exclusión expresada arriba puede no ser

aplicable a usted.

Esta garantía le da a usted derechos legales especícos

y usted puede también tener otros derechos que varían

de estado a estado.

Esta garantía es nula por cualquier daño a esta llave

que sea el resultado del mal uso, abuso, negligencia,

accidente, instalación impropia, cualquier uso en

violación de las instrucciones suministradas por

nosotros o cualquier uso de piezas de repuesto que no

sean piezas genuinas Delta.

Piezas y Acabado. Todas las piezas (excepto los componentes electrónicos y las pilas) y los acabados de los grifos Delta Faucet® comprados de vendedores autor-

izados por Delta están garantizados al consumidor comprador original de estar libres de defectos en material y fabricación durante el tiempo que el comprador original

sea propietario de la vivienda en la que el grifo/la llave de agua fue originalmente instalada. En el caso de los consumidores comerciales, (a) el período de garantía

es de diez (10) años para aplicaciones multifamiliares (apartamentos y condominios) y (b) cinco (5) años para todos las otras aplicaciones comerciales, en cada caso

a partir de la fecha de compra. Para los propósitos de esta garantía, el término “aplicación multifamiliar residencial” se refiere a la compra del grifo de un vendedor

autorizado por Delta por el comprador propietario que no vive en la vivienda residencial donde se instaló inicialmente la llave de agua, como en una unidad alquilada

o arrendada, o unidad o vivienda unifamiliar separada (dúplex o casas adosadas), o un condominio, edificio de apartamentos o centro de vivienda comunitaria. Las

siguientes instalaciones no se consideran aplicaciones multifamiliares residenciales, están excluidas de la garantía de 10 años y están sujetas a la garantía de cinco

años: instalaciones industriales, institucionales u otras instalaciones comerciales, como dormitorios, instalaciones de hotelería (hotel, motel o una alberga para estadías

prolongadas), aeropuerto, centro educativo, centro de atención de salud a corto o largo plazo (hospital, centro de rehabilitación, asilo de ancianos, unidad de vivienda

asistida o una unidad residencial de cuidado), espacio público o área común.

Piezas y acabados para grifos recertificados Delta®. Delta Faucet Company ofrece para la venta en deltafaucet.com llaves de agua/grifos recertificados Delta®. Todas

las piezas electrónicas (excepto las partes electrónicas y las pilas) y los acabados de estos grifos recertificados Delta® están garantizados al consumidor comprador

original de estar libres de defectos en material y fabricación durante diez (10) años a partir de la fecha de compra. Para los consumidores comerciales, el período de

garantía es por un (1) año a partir de la fecha de compra.

Piezas electrónicas. Las piezas electrónicas (excepto las pilas), si las hay, de las llaves de agua Delta® compradas de deltafaucet.com o vendedores autorizados por

Delta están garantizadas al consumidor comprador original de estar libres de defectos en material y fabricación durante cinco (5) años a partir de la fecha de compra o

para los consumidores comerciales, por un (1) año a partir de la fecha de compra. No se garantizan las pilas.

Lo que haremos. La compañía Delta Faucet Company reparará o reemplazará, sin costo alguno, durante el período de garantía aplicable (como descrito arriba)

cualquier pieza o acabado que demuestre ser defectuosa en material y/o fabricación bajo la instalación, el uso y el servicio normal. Si la reparación o el reemplazo no

es práctico, Delta Faucet Company puede optar por reembolsarle el precio de compra a cambio de la devolución del producto. Estos son sus remedios exclusivos.

Lo que no cubre. Debido a que Delta Faucet Company no puede controlar la calidad de los productos Delta vendidos por vendedores no autorizados, a menos que la

ley lo prohíba, esta garantía no cubre los productos Delta comprados a vendedores no autorizados.

No cubre cualquier gasto de labor incurrido por el comprador para reparar, reemplazar, instalar o desmontar este producto. Delta Faucet Company no es responsable por

cualquier daño al grifo que resulte del desgaste razonable, uso en el exterior, uso indebido, (incluyendo el uso del producto para una aplicación indebida), agua helada,

abuso, negligencia o la instalación, el mantenimiento o la reparación incorrecta, incluido el incumplimiento de las instrucciones de cuidado y limpieza correspondientes.

Delta Faucet Company recomienda el uso de los servicios de un plomero profesional para toda instalación y reparación de los grifos. También recomendamos que use

solo piezas de repuesto genuinas Delta®.

Lo que usted debe hacer para obtener servicio de garantía o piezas de repuesto. Se puede hacer un reclamo de la garantía y se pueden obtener piezas de repuesto

llamando al 1-877-345-DELTA (3358) o contactándonos por correo postal o electrónico como indicado (favor incluya el número del modelo y la fecha de compra):

En los Estados Unidos y México: En Canadá:

Delta Faucet Company Masco Canada Limited, Plumbing Group

Product Service Technical Service Centre

55 E. 111th Street 350 South Edgeware Road

Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1

Attention: Warranty Service Attention: Warranty Service

www.deltafaucet.com/service-parts/contact-us http://www.deltafaucet.ca/customersupport/assistance.html

El comprobante de compra (recibo de venta original) del comprador original debe ser disponible a Delta Faucet Company para todos los reclamos de garantía a menos

que el comprador haya registrado el producto en Delta Faucet Company o es un producto recertificado de Delta® comprado de deltafaucet.com. Esta garantía aplica

solo a las llaves de agua/grifos Delta® fabricados después de enero 1, 2019 e instalados en los Estados Unidos de América, Canadá y México.

La limitación de la duración de las garantías implícitas. Favor tomar nota que algunos estados/provincias (incluyendo Quebec) no permiten las limitaciones de

la duración de una garantía implícita por lo que las limitaciones a continuación puedan no aplicarle. HASTA EL ALCANCE MÁXIMO EN QUE LA LEY LO PERMITA,

CUALQUIER GARANTÍA IMPLÍCITA, INCLUIDAS LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD Y DE IDONEIDAD PARA UN PROPÓSITO PARTICULAR,

ESTÁ LIMITADA AL PERÍODO LEGAL O A LA DURACIÓN DE ESTA GARANTÍA, LO QUE SEA MÁS CORTO.

Limitación de daños especiales, incidentales o consiguientes. Favor de tomar nota que algunos estados/provincias (incluyendo Quebec) no permiten la exclusión

o limitación de daños especiales, incidentales o consecuentes, por lo que estas limitaciones y exclusiones puedan no aplicarle. HASTA EL ALCANCE EN QUE LA

LEY LO PERMITA, ESTA GARANTÍA NO CUBRE Y DELTA FAUCET COMPANY NO SE HACE RESPONSABLE, POR NINGÚN DAÑO ESPECIAL, INCIDENTAL

O CONSIGUIENTE (INCLUYENDO LOS GASTOS DE LABOR PARA REPARAR, REEMPLAZAR, INSTALAR O DESMONTAR ESTE PRODUCTO), YA SEA EL

RESULTADO DEL INCUMPLIMIENTO DE CUALQUIER GARANTÍA EXPRESA O IMPLÍCITA, INCUMPLIMIENTO DE CONTRATO, AGRAVIO O DE OTRA MANERA.

DELTA FAUCET COMPANY NO SE RESPONSABILIZAR POR CUALQUIER DAÑO AL GRIFO QUE RESULTE DEL DESGASTE RAZONABLE, USO EN EL EXTERIOR

DE LA PROPIEDAD, USO INDEBIDO (INCLUYENDO EL USO DEL PRODUCTO PARA UNA APLICACIÓN INDEBIDA), AGUA HELADA, ABUSO, NEGLIGENCIA O

INSTALACIÓN O MANTENIMIENTO INADECUADO O INCORRECTO, INCLUYENDO EL NO SEGUIR LAS INSTRUCCIONES CORRESPONDIENTES PARA EL

CUIDADO, LA LIMPIEZA Y EL MANTENIMIENTO. Aviso para los residentes del estado de New Jersey: Las disposiciones de este documento tienen la intención de

aplicarse en la máxima medida permitida por las leyes del estado de New Jersey.

Derechos adicionales. Esta garantía le otorga derechos legales específicos y también puede tener otros derechos que varían de estado/provincia a estado/provincia.

Esta es la garantía escrita exclusiva de Delta Faucet Company y la garantía no es transferible.

Si tiene preguntas o dudas con respecto a nuestra garantía, por favor comuníquese con nosotros como se indica anteriormente o consulte nuestras Preguntas Frecuentes

Warranty FAQs en www.deltafaucet.com.

Garantía Limitada en las Llaves de Agua de Delta

107528 Rev. D

Instalación de la plomería MultiChoice

(Cuando su producto lo requiere)

CIERRE LOS SUMINISTROS DE AGUA.

Considere el tipo y el grosor de su pared

terminada antes de colocar su placa trasera

de acoplamiento de las tuberías. Instale la

pieza (1) de manera que la superficie de la

pared terminada quede al ras con el frente

del protector de yeso (2) ± 3/8". Nota: Para

con los modelos de las paradas (3), el

protector del yeso debe ser el rubor

rasante o secundario el 3/8”a la pared

acabada. Instale la pieza usando los dos

agujeros de instalación del acoplamiento

(4) en el soporte. Cuando esté haciendo la

instalación, asegúrese que la palabra

“UP” (5) quede arriba de la válvula.

La distancia (1) del larguerillo (2) a la

parte delantera del protector de yeso es

de 2.8" (71 mm).

Si se utiliza una pared delgada,

asegúrese de tener el protector de yeso

por detrás de la pared, de lo contrario, la

pared siempre debe estar al ras con la parte

delantera del protector de yeso. Consulte

las instrucciones en la bolsa para el montaje

en pared delgada.

107528 Rev. D

Conecte el cuerpo de la válvula a los sumin-

istros de agua usando los accesorios apro-

piados para el tipo de su válvula (tubería de

cobre, hierro o Pex). Nota: (1) es la entrada

del agua fría y el (2) es la entrada del agua

caliente. Si no va a usar alguna de las dos

entradas de agua, séllela con un tapón

de tubería.

Si está hacienda una instalación dorso

con dorso o a la inversa (caliente en la

derecha y fría en la izquierda) instale el

cuerpo de la válvula como se describe

arriba, pero coloque al inverso las líneas

de suministro de agua. Nota: (1) es

la entrada de agua caliente (2) es la

entrada del agua fría.

Tubería de

Cobre

Hierro

Pex

Quite el capuchón (1).

AVISO: Evite soldar a altas temperaturas. Los

componentes de las tuberías detrás de las

paredes podrían dañarse.

Sea seguro que las válvulas apagadas

(2) están quitadas de la versión con las

paradas antes de soldar. (no instale las

válvulas apagadas antes de soldar.)

107528 Rev. D

Instalación

Conecte la salida de arriba (1) a la tubería de

la regadera con los accesorios apropiados.

Conecte la salida de abajo (2) a la tubería

del surtidor de la bañera con los accesorios

apropiados. La tubería (3) entre el cuerpo de

la válvula y el de la bañera debe ser de un

mínimo de 1/2" (13 mm) de tubería de cobre

ó 1/2" (13 mm) de tubería de hierro en caída

recta no menos de 8" (203 mm) pero no más

de 18" (457 mm) de largo a la entrerrosca del

surtidor de la bañera y con sólo un codo de 90

grados, de tubería de hierro o cobre. No use la

tubería PEX como tubería entre la válvula y

el surtidor de la bañera.

PRUEBA DE PRESIÓN Y

LIMPIEZA DE LA INSTALACIÓN

• Para enjuagar el sistema de desechos,

retire la tuerca tapa

(1).

• Prepare el área para rociar con agua.

• Lentamente abra los suministros de

agua para depurar el sistema por 30

segundos.

• Después de enjuagar, instale el

cartucho y la tuerca tapa.

• Gire la espiga del cartucho en sentido

antihorario hasta que pare.

PARA LOS MODELOS CON TOPES, instale los topes, pero

déjelos en posición completamente abierta. Instale los topes de la

siguiente manera:

• Enrosque la tuerca (2) en la espiga (3) como se muestra. A

continuación, presione el ensamble de la espiga y la tuerca en

la unidad y apriételo con una herramienta de tubo largo con

entrada de 6 puntos de 3/8”. Con un destornillador de cabeza

plana, ajuste la espiga en el sentido de las agujas del reloj para

cerrarla y en el sentido contrario a las agujas del reloj para

abrirla.

• Tape el surtidor de la bañera y/o la salida o salidas de agua de

la regadera con el accesorio apropiado para su tubería.

• Examine si hay fugas.

• Después de hacer la prueba de fugas o filtraciones de agua,

cierre la válvula girando la espiga del cartucho completamente

en el sentido de las agujas del reloj.

107528 Rev. D

Instalación del Cartucho

Cierre los suministros de agua. Quite la

la tuerca tapa (1) y la tapa de prueba (2). Si

no es para instalar en pared delgada, puede

quitar el protector (3) de yeso completo. Si

la pantalla (4) está en lugar, quite antes de

instalar el cartucho.

Gire el cartucho de la válvula (1) de forma que

las palabras "HOTTER COLDER" estén en la

parte superior. Inserte el cartucho en el cuerpo

de la tubería preliminar.

Una ligera capa de grasa de plomería aplicada

a las juntas tóricas puede ayudar en el

montaje. Asegúrese de que el dentado en el

cuerpo está totalmente encajado en la muesca

en el cuerpo de bronce (4).

Instalación de Espalda a Espalda

En las instalaciones dorso con dorso o al

reverso (caliente en la derecha y fría en

la izquierda) introduzca el cartucho con la

inscripción “hot side” a la derecha. Si usted

no está instalando al reverso o dorso con

dorso omita este paso y continúe con el

paso 2C.

Deslice la tuerca tapa (1) sobre el cartucho

y enrosque en el cuerpo de la válvula.

Apriete a mano bien.

Instalación Normal (No serequerá cambios)

Instalación

Invertido

Fría

Caliente

La page charge ...

Delta Faucet T14159-CZ Manuel utilisateur

Marque: Delta Faucet

Modèle: T14159-CZ

Catégorie: Articles sanitaires

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Delta Faucet T14159-CZ User manual
español: Delta Faucet T14159-CZ Manual de usuario

Delta Faucet T14159-CZ Manuel utilisateur

Delta Faucet T14159-CZ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents