Maytag 7MMVWH450DW0 Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
TOP=LOADING
HiGH EFFiCiENCY
LOW=WATER WASHER
USE AND CARE GUIDE
GUIDE D'UTILISATION
ET D'ENTRETIEN DE
LA LAVEUSE HAUTE
EFFICACIT( =.,_FAIBLE
CONSOMMATION D'EAU
AVEC CHARGEMENT PAR
LE DESSUS
Para una versi6n de estas instrucciones en espa_ol, visite www.maytag.com
Table of Contents
WASHER SAFETY ............................................................. 2
WHAT'S NEW UNDER THE LID? ..................................... 3
CONTROL PANEL AND FEATURES ................................ 4
CYCLE GUIDE ................................................................... 6
USING YOUR WASHER .................................................... 7
WASHER MAINTENANCE .............................................. 10
TROUBLESHOOTING ..................................................... 12
WARRANTY ..................................................................... 17
ASSISTANCE OR SERVICE ........................ BACK COVER
Table des mati_res
S¢:CURIT¢: DE LA LAVEUSE .......................................... 18
QUOI DE NEUF SOUS LE COUVERCLE? ..................... 19
TABLEAU DE COMMANDE ET
CARACTC:RISTIQUES ..................................................... 20
GUIDE DE PROGRAMMES ............................................ 22
UTlUSATION DE LA LAVEUSE ...................................... 23
ENTRETIEN DE LA LAVEUSE ........................................ 26
DF:PANNAGE ................................................................... 29
GARANTIE ....................................................................... 35
ASSISTANCE OU SERVICE ...... COUVERTURE ARRI#RE
Designed to use only
HE High Efficiency detergents.
Congue pour I'utilisation d'un
d6tergent haute efficacit6 seulement.
W10560155B
W10560156B =SP
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey aft
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[]
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. Ifthe hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach into the washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" located in the installation
instructions for grounding instructions.
this time.
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
2
WHAT'S NEW UNDER THE LID?
Cleaning with Less Water
Traditional agitator-style
washer
Washer with low-water
washplate wash system
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size--no water level selector is needed.
For best performance, it is recommended to load garments in
loose heaps evenly around the washplate.
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. This may take several minutes before water is
added. You will find a step-by-step description in the "Cycle
Status Lights" section.
You will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be
marked "HE" or "High Efficiency." Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of detergent to use.
Use only High Efficiency (HE) detergent.
Concentrated Cleaning
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
As the washer dampens and moves the load, the level of the
garments will settle in the basket. This is normal, and does not
indicate that more garments should be added.
IMPORTANT: You will not see a washer basket full of water
as with your past agitator-style washer. It is normal for some
of the load to be above the water line.
Norma Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for clothes to soak.
CONTROL PANEL AND FEATURES
soil [eve[ wash temp
bulky/ nerrnat
sheets wrinkle control
deep water wash s / \ _,hand wash
\
power wash I _I cold wash
i
off on
extra rinse
3
off on
P_werWash
,'_._" SFSTEM
L
Not all features and options are available on all models.
Appearance may vary.
O SOIL LEVEL
Select the most suitable setting for your load. For heavily
soiled and sturdy fabrics, select Extra Heaw Soil Level for
more wash time, if needed. For lightly soiled and delicate
fabrics, select Light Soil Level for less wash time, if needed.
Lighter soil level setting will help reduce tangling and
wrinkling.
WASH TEMP
Wash Temp senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following the
garment label instructions, use the warmest wash water safe
for your fabric.
• On some models and cycles, warm and hot water may be
cooler than your previous washer.
• Even in a cold and cool water wash, some warm water
may be added to the washer to maintain a minimum
temperature.
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See "Cycle Guide" for detailed descriptions.
O
O
CYCLE OPTIONS
The following options may be added to most cycles.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
FABRIC SOFTENER ADDED
This option must be set to "On" if using fabric softener.
START/PAUSE/UNLOCK BUTTON
Press to start the selected cycle; press again to pause the
cycle and unlock the lid. Press and hold 3 sec to cancel a
cycle.
NOTE: If the washer is spinning, it may take several minutes
to unlock the lid. Press and hold 3 sec to cancel a cycle.
O
CYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At
each stage of the process, you may notice sounds or pauses
that are different from traditional washers.
SENSING
When the START/Pause/Unlock button is pressed,
the washer will first perform a self-test on the lid lock
mechanism. You will hear a click, the basket will make a
slight turn, then lid will unlock briefly before locking again.
Once the lid has locked the second time, the washer will
use short, slow spins to estimate the load size. These
sensing spins may take 2 to 3 minutes before water is
added to the load and you may hear the hum of these
spins. Ifthe Sensing light is on, the washer is working
properly. You will hear the motor turn the basket in short
pulses to thoroughly wet the load. The washer will then
move the load briefly, pause to allow water to soak into
the load, and resume adding water. This process may
repeat until the correct amount of water has been added
for the load. You may also hear water flowing through the
dispenser, adding detergent to the load.
NOTE: Avoid opening the lid during sensing. The sensing
process will start over when the washer is restarted. The
Sensing light may also come on during the Wash portion
of the cycle. This is normal.
WASH
seesin8 wash rinse spin dene lid lecked
You will hear the motor and washplate moving the load.
Unlike traditional washers, the load is not covered with
water. Low-water cleaning means concentrated cleaning.
Rather than diluting detergent as done in an agitator-style
washer, this washer delivers the detergent directly to the
soils. The motor sounds may change at different stages
in the cycle. The wash time is determined by the selected
soil level.
4
RINSE
sensingwash rinse spin done lidlocked
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. Fabric softener will
be added if the Fabric Softener-On option was selected.
Some cycles will use a spray rinse.
SPiN
sensing wash rinse spin done [idlocked
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle and spin
speed.
LID LOCKED
seosing wash rinse spin done lidlocked
To allow for proper load sensing and spinning, the lid
will lock and the Lid Locked light will turn on. This light
indicates that the lid is locked and cannot be opened.
If you need to open the lid, press
START/Pause/Unlock. The lid will unlock ( I_11_ start
once the washer movement has stopped. \ "'/p_0,e/o,tock
W hold 3 _ec
This may take several minutes if the load .........
was spinning at high speed. Press START/
Pause/Unlock again to resume the cycle. Avoid
opening the lid during sensing. The sensing process
will start over when the washer is restarted.
DONE
sensing wash rinse spin done lidlocked
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
CYCLE GUIDE
For best fabric care, choose the cycle that best fits the load being washed.
Recommended settings for best performance are shown in Bold.
Not all cycles and options are available on all models.
Sturdy fabrics, colorfast Power Wash® Hot High Use this cycle for heavilysoiled or sturdy items. Water-level sensing
items, towels, jeans Warm process may take longer for some items than for others because they will
Cool absorb more water than other fabric types.
Cold
Tap Cold
Casual and mixed loads, Deep Water Hot Low Provides additional water and alternating wash action for heavily soiled
jeans, towels, sturdy Wash Warm mixed loads. Water-level sensing process may take longer for some items
fabrics Cool than for others because they will absorb more water than other fabric types.
Cold
Tap Cold
Largeitems such as Bulky/Sheets Hot High Use this cycle to wash large items such as jackets and small comforters.
sheets, sleeping bags, Warm The washer will fill with enough water to wet down the load before the wash
small comforters, jackets, Cool portion of the cycle begins, and uses a higher water level than other cycles.
small washable rugs Cold
Tap Cold
Cottons, linens, and Normal Hot High Use this cycle for normally soiled cottons and mixed fabric loads. This
mixed garment loads Warm cycle uses spray rinses.
Cool
Cold
Tap Cold
No-iron fabrics, cottons, Wrinkle Control Hot Low Usethis cycle to wash loads of no-iron fabrics such as sport shirts,
perm press, linens, Warm blouses, casual business clothes, permanent press, and blends.
synthetics Cool
Cold
Tap Cold
Machine-wash silks, Hand Wash Hot Low Usethis cycle to wash lightly soiled garments indicating "Machine
handwash fabrics Warm Washable Silks" or "Gentle" cycle on the care label. Place small items in
Cool mesh garment bags before washing. This cycle uses a higher, preset water
Cored level.
Tap Cold
Bright or darkly colored Cold Wash Cold High Cold water with an additional wash action gently lifts stains while caring for
cottons, linens, casual fabrics. Settings may be adjusted as desired, but must use only cold water
and mixed loads settings.
Heavily soiled fabrics Soak Hot No Spin Use this cycle to soak small spots of set in stains on fabrics. The
Warm washer will use intermittent agitation and soaking. After time has
Cool expired, water will drain, but the washer will not spin. Cycle is
Cold complete.
Tap Cold
Swimsuits and items Rinse & Cold rinse only High Combines a rinse and high speed spin for loads requiring an
requiring rinsing Spin additional rinse cycle or to complete a load after power interruption.
without detergent Also use for loads that require rinsing only.
Hand-washed Drain & N/A High This cycle uses a spin to shorten drying times for heavy fabrics or
garments or Spin special-care items washed by hand. Use this cycle to drain washer
dripping wet items after cancelling a cycle or completing a cycle after a power failure.
No clothes inwasher LowClean Washer
with
affresh®
Hot
Warm
Cool
Cold
Tap Cold
Use this cycle every 30 washes to keep the inside of your washer fresh
and clean. This cycle uses a higher water level. Use with affresh®Washer
Cleaner tablet or liquid chlorine bleach to thoroughly clean the inside of
your washer. This cycle should not be interrupted. See "Washer Care."
IMPORTANT: Do not place garments or other items in the washer during
the Clean Washer with affresh®cycle. Usethis cycle with an empty wash
tub.
NOTE: If you are using fabric softener, be sure to select the Fabric Softener-On option.
*All rinses are cold.
6
USmNG YOUR WASHER
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1, Sort and prepare your laundry
• Empty pockets. Loose change, buttons, or any small
object can pass under the washplate and become trapped,
causing unexpected sounds.
• Sort garments by recommended cycle, water temperature,
and colorfastness.
• Separate heavily soiled garments from lightly soiled.
• Separate delicate garments from sturdy fabrics.
• Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes, and
remove non-washable trim and ornaments.
• Mend rips and tears to avoid further damage to garments
during washing.
Helpful Tips:
= When washing water-proof or water-resistant items, load
evenly. See "Cycle Guide" for tips and more information on
using the Bulky cycle.
• Use mesh garment bags to help avoid tangling when
washing delicate or small items.
• Turn knits inside out to avoid pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
Always read and follow fabric care label instructions to avoid
damage to your garments.
f2, Add laundry products
1
Single-dose laundry packet, color-safe bleach, Oxi-type
booster, or fabric softener crystals can be added to the basket
prior to adding laundry.
NOTE: Do not add clothes to washer basket prior to adding
laundry products. Always follow manufacturer's instructions.
For best performance, load garments --_
in loose heaps evenly around the
washplate. Try mixing different sized
garments to reduce tangling, j
IMPORTANT: Garments need to move
freely for best cleaning and to reduce wrinkling and tangling.
Using Laundry Product Dispensers
NOTE: Do not add single-dose laundry packets, color-safe
bleach, Oxi-type boosters, or fabric softener crystals to
dispensers. They will not dispense correctly.
Add HE detergent
Detergent tray
Add a measured amount of
HE detergent into detergent tray. This
tray holds 3 oz. (89 mL). Do not overfill tray - adding too
much detergent may cause detergent to be dispensed into
the washer too early.
IMPORTANT: Use only High Efficiency detergents. The
package will be marked "HE" or "High Efficiency." Low-water
washing creates excessive sudsing with a regular non-HE
detergent. Using regular detergent will likely result in longer
cycle times and reduced rinsing performance. It may also
result in component failures and noticeable mold or mildew.
HE detergents are made to produce the right amount of
suds for the best performance. Follow the manufacturer's
instructions to determine the amount of detergent to use.
HELPFUL TIP: See "Washer Maintenance" for information
on recommended method of cleaning washer dispenser trays.
to dispenser
, Add liquid fabric softener
to dispenser
Fabric softener tray
Pour a measured amount of liquid fabric
softener into tray; always follow manufacturer's
directions for correct amount of fabric softener
based on your load size. Close dispenser
drawer, then select Fabric Softener option.
Fabric Softener is added during rinse.
fabric softener
IMPORTANT: Fabric Softener option must be selected
to ensure proper distribution at correct time in cycle. Do
not overfill or dilute. Overfilling dispenser will cause fabric
softener to immediately dispense into washer.
If Extra Rinse option is selected, fabric softener will be
dispensed into the last rinse.
It is normal for a small amount of water to remain in the
dispenser at the end of a cycle.
fT. Select cycle
bulky/ normal
sheets _--_ wrinkle control
deep water wash t _hand wash
cold wash
Turn cycle knob to choose your wash cycle.
Do not overfill, dilute, or use more than 1 cup (250 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach.
8
f
8= Select SOIL LEVEL
medium heavy
iiiiiiiiiiii_ii_iiiiii_iiiiiiiiii
soil level
Once you select a cycle, select the desire soil level by turning
the Soil Level knob to the desired setting.
9, Select wash temperature
cool
wash temp
Once you select a cycle, select the desire wash temperature
by turning the Wash Temp knob to the desired setting.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Not
Some cold water is added to save
energy. This will be cooler than
your hot water heater setting.
Whites and pastels
Durable garments
Heavy soils
Warm
Some cold water will be added, so Bright colors
this will be cooler than what your ;_Moderate to light soils
previous washer provided.
Cool
Warm water is added to assist in
soil removal and to help dissolve
detergents.
Cold
Colors that bleed
or fade
Light soils
Warm water may be added to Dark colors that
assist in soil removal and to help bleed or fade
dissolve detergents.
Tap Cold
This is the temperature from your Dark colors that
faucet, bleed or fade
Light soils
f
1 O, Select cycle options, if desired
off on off on
i!iiiiiiiii_,,,,iii!]_il
extra rinse fabric softener
If you would like to add an Extra Rinse and/or Fabric Softener
option, turn the knob for that feature to ON.
fl - 1, Press START/Pause/Unlock
to begin wash cycle
(_ start
°ck
to cancel
Press the START/Pause/Unlock button to start the wash
cycle. When the cycle has finished, the DONE indicator will
light. Promptly remove garments after cycle has completed
to avoid odor, reduce wrinkling, and rusting of metal hooks,
zippers, and snaps.
Unlocking the lid to add garments
If you need to open the lid to add 1 or 2 missed garments:
Press START/Pause/Unlock; the lid will unlock once the
washer movement has stopped. This may take several
minutes if the load was spinning at high speed. Then close lid
and press START/Pause/Unlock again to restart the cycle.
If lid is left open for more than 10 minutes the water will pump
out automatically.
WASHER MAMNTENANCE
WATER iNLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See
the "Installation Instructions" for more information.
r
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer's instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help
dry out the washer and prevent the buildup of odor-
causing residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly
cleaning procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water
volumes in combination with affresh ®Washer Cleaner
or liquid chlorine bleach to clean the inside of the washer.
Begin procedure
1. affresh ®Washer Cleaner Cycle Procedure
{Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
bo Place an affresh ®Washer Cleaner tablet in the bottom
of the washer basket.
co Do not place an affresh ®Washer Cleaner tablet
in the detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
eo Close the washer lid.
fo Select the CLEAN WASHER cycle.
g. Press the START/Pause/Unlock button to begin the
cycle. The Clean Washer Cycle Operation is described
below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
Pause/Unlock for three seconds). After the Clean Washer
cycle has stopped, run a RINSE & SPIN cycle to rinse
cleaner from washer.
f WASHER CARE (cont.)
2. Chlorine Bleach Procedure {Alternative):
ao Open the washer lid and remove any clothing
or items.
bo Add 1 cup (236 mL) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
co Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
eo Select the CLEAN WASHER cycle.
f. Press the START/Pause/Unlock button to begin the
cycle. The Clean Washer Cycle Operation is described
below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
Pause/Unlock for three seconds). After the Clean Washer
cycle has stopped, run a RINSE & SPIN cycle to rinse
cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will fill to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may find some
residue buildup in the washer's dispensers. To remove
residue from the dispensers, wipe them with a damp cloth
and towel dry. Do not attempt to remove the dispensers or
trim for cleaning. The dispensers and trim are not removable.
If your model has a dispenser drawer, however, remove the
drawer and clean it before or after you run the Clean Washer
cycle. Use an all-purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
iMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
10
r
NON=USE AND VACATION CARE
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
r
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
r
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain hose from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials
back inside washer. If you do not have packing tray,
place heaw blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in new
location.
r
RE! NSTALLING/USI NG WASHER AGAI N
1.
2.
To
1.
To reinstall washer after non-use, vacation, winter storage,
or moving:
Refer to "Installation Instructions" to locate, level, and
connect washer.
Before using again, run washer through the following
recommended procedure:
use washer again:
Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. Plug in washer or reconnect power.
3. Run washer through BULKY/SHEETS cycle to clean
washer and remove antifreeze, if used. Use only HE
High Efficiency detergent. Use 1/2 the manufacturer's
recommended amount for a medium-size load.
11
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience
Possible Causes
Feet may not be in contact with the
floor and locked.
Washer may not be level.
Load could be unbalanced.
Check the following for
proper installation or see
"Using Your Washer"
section.
Solution
Front and rear feet must be in firm contact with floor, and
washer must be level to operate properly. See "Installation
Instructions".
Check floor for flexing or sagging. Ifflooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See "Level the Washer" in Installation Instructions.
Load dry items in loose heaps evenly around washplate.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Wash smaller loads to reduce imbalance.
Do not tightly pack. Avoid washing single items.
Use Bulky/Sheets cycle for oversized, non-absorbent items such
as comforters or poly-filled jackets.
See "Cycle Guide" and "Using Your Washer" in this Use and
Care Guide.
Clicking or metallic
noises
Gurgling or humming
Humming
Objects caught in washer
drain system.
Washer may be draining water.
Load sensing may be occurring.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump. It may
be necessary to call for service to remove items.
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
It is normal to hear the pump making a continuous humming
sound with periodic gurgling or surging as final amounts of
water are removed during the spin/drain cycles.
You may hear the hum of the sensing spins after you have
started the washer. This is normal.
Check the following for
proper installation:
Washer not level.
Fill hoses not attached tightly.
Fill hose washers.
Drain hose connection.
Check household plumbing for leaks
or clogged sink or drain.
Water may splash off basket if washer is not level.
Check that load is not unbalanced or tightly packed.
Tighten fill-hose connection.
Make sure all four fill hose flat washers are properly seated.
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Do not place tape over drain opening.
Water can backup out of a clogged sink or drainpipe. Check all
household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets.)
Washer not loaded as
recommended.
Unbalanced loading can cause basket to be out of alignment
and cause water to splash off tub. See "Using Your Washer" for
loading instructions.
Not enough water
in washer
Load not completely covered
in water.
This is normal operation for an HE low-water washer. The load
will not be completely underwater. The washer senses load sizes
and adds correct amount of water for optimal cleaning. See
"What's New under the Lid."
IMPORTANT: Do not add more water to washer.
J
12
TROUBLESHOOTING
f
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
if you experience
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Possible Causes _ Solution
J
Washer won't run
or fill, washer stops
working or wash light
remains on (indicating
that the washer
was unable to fill
appropriately)
Check for proper water supply.
Check proper electrical supply.
Normal washer operation.
Washer may be tightly packed.
Not using HE detergent or using too
much HE detergent.
Both hoses must be attached and have water flowing to inlet
valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water flow.
Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle. Do not
interrupt cycle.
Washer may be stopped to reduce suds.
Remove several items, rearrange load evenly in basket and add
detergent. Close lid and press START/Pause/Unlock.
Do not add more than 1 or 2 additional items after cycle has
started to avoid tightly packing or unbalancing.
Do not add more water to the washer.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and follow
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select RINSE & SPIN. Press
START/Pause/Unlock. Do not add more detergent.
J
13
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience
Washer not draining/
spinning, loads are
still wet, or spin light
remains on (indicating
that the washer was
unable to pump out
water within 10 minutes)
Dry spots on load
after cycle
Incorrect or wrong
wash or rinse
temperatures
Possible causes Solution
Empty pockets and use garment bags Small items may have been caught in pump or between basket
for small items, and tub, which can slow draining.
Using a cycle with a low spin speed.
The washer may be tightly packed or
unbalanced.
Check plumbing for correct
drain hose installation. Drain hose
extends into standpipe farther than
4.5" (114 mm).
Too much detergent causing suds to
slow or stop draining and spinning.
High speed spins extract more
moisture than traditional top-load
washers.
Check for proper water supply.
Energy saving controlled
wash temperatures.
Load not rinsed Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer not loaded as recommended.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/spin speed
for your garment. To remove extra water in the load, select
DRAIN & SPIN. Load may need to be rearranged to allow even
distribution of the load in the basket.
Tightly packed or unbalanced loads may not allow the washer
to spin correctly, leaving the load wetter than normal. Evenly
arrange the wet load for balanced spinning. Select the Drain &
Spin cycle to remove excess water. See "Using Your Washer" for
loading recommendations.
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the floor. Remove any clogs from drain hose.
Use only HE detergent. Always measure and follow detergent
directions for your load. To remove extra suds, select RINSE &
SPIN. Do not add detergent.
The high spin speeds combined with air flow during the final spin
can cause items near the top of the load to develop dry spots
during the final spin. This is normal.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
ENERGY STAR®qualified washers use cooler wash and rinse
water temperatures than your previous washer. This includes
cooler hot and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can keep washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
The washer is less efficient at rinsing when tightly packed.
Load garments in loose heaps evenly around the washplate. The
washer will not rinse well if tightly packed. Load with dry items
only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
J
14
TROUBLESHOOTING
f First try the solutions suggested here or visit our website at www.maytag.com/product_help - -_
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience j Possible Causes Solution
Add an Extra Rinse to the selected cycle.Sand, pet hair, lint, etc.
on load after washing
Load is tangling
Heaw sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Washer not loaded as recommended.
Added more water to washer.
Washer not loaded as recommended.
Adding detergent on top of load.
See "Using Your Washer" section.
Select a cycle with a slower wash action and spin speed, however
items will be wetter than those using a higher speed spin. See the
"Cycle Guide" to match your load with the best cycle.
Load garments in loose heaps evenly around the washplate.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Washer senses load size and adds correct amount of water.
This is normal and necessary for clothes to move. It is normal
for the wash load to be not completely covered in water.
Added water lifts the laundry off the washplate, resulting in less
effective cleaning.
Washer is less efficient at cleaning when tightly packed.
Load garments in loose heaps evenly around the washplate.
Load with dry items only.
Add only 1 or 2 garments after washer has started.
Add detergent, oxi products and color-safe bleach to the bottom
of the basket before adding the load items.
Not washing like colors together. Wash like colors together and remove promptly after the cycle is
complete to avoid dye transfer.
Not using HE detergent or using too
much HE detergent.
Not cleaning or
removing stains
Not using correct cycle for fabric type.
Not using dispenser or Downy Ball®.
Not selecting Fabric Softener-On.
Incorrect dispenser Clogged dispenser.
_,£peration
The suds from regular detergent can keep washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow manufacturer's directions
based on load size and soil level.
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning.
Use Power Wash® cycle for tough cleaning. See the "Cycle
Guide" to match your load with the best cycle and fabric type.
Use dispenser for chlorine bleach and Downy Ball®dispenser for
fabric softener to avoid staining.
Load dispenser before starting a cycle.
Do not add products directly onto load.
Always select "On" when adding fabric softener. Cycles that use
spray rinsing will add additional water for proper fabric softener
dispensing when "On" is selected.
Use only liquid chlorine bleach in the bleach dispenser.
J
15
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience I Possible Causes Solution
Fabric Damage Sharp items were in pockets during Empty pockets, zip zippers, and snap or hook fasteners before
wash cycle, washing to avoid snags and tears.
Strings and straps could have tangled. Tie all strings and straps before starting wash load.
Odors
Items may have been damaged before Mend rips and broken threads in seams before washing.
washing.
Fabric damage can occur if washer is
tightly packed.
Liquid chlorine bleach may have been
added incorrectly.
Garment care instructions may not
have been followed.
Monthly maintenance not done as
recommended.
Using wrong or too much detergent.
Load garments in loose heaps evenly around the washplate.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer is started.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Always read and follow garment manufacturer's care label
instructions. See the "Cycle Guide" to match your load with
the best cycle.
Run the Clean Washer with affresh ®cycle monthly. See "Washer
Care" inWasher Maintenance.
Unload washer as soon as cycle is complete.
Use only HE detergent. Be sure to measure correctly. Always
follow the manufacturer's directions.
See "Washer Care" section.
Lid locked light is The lid is not closed. Close the lid. The washer will not start or fill with the lid open.
flashing A cycle was stopped or paused The washer may still be spinning. The lid will not unlock until the
using the Start/Pause/Unlock button, basket has stopped spinning. This may take several minutes if
washing large loads or heavy fabrics.
Single-dose laundry Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding
packet not dissolving clothes. Follow the manufacturer's instructions to avoid damage
to your garments.
16
HAYTAG ® LAUNDRY WARRANTY
LiMiTED WARRANTY
For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions
attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will
pay for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this
major appliance was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Service must be provided by a Maytag designated service company. This limited warranty is valid only in the United States or Canada
and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the
date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
iTEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when
it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace
or repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by
an authorized Maytag servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Maytag published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered,
or cannot be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DiSCLAiMER OF iMPLiED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and
provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply
to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to
province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR iNCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
if outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
if you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve
the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by
calling Maytag. in the U.S.A., call 1=800=688=9900. in Canada, call 1=800=807=6777. 10/11
Keep this book and your sales slip together for future
reference, You must provide proof of purchase or installation
date for in=warranty service,
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need
it. You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
17
SECURmTE DE LA VEUSE
Votre s_curit_ et celle des autres est tr_s importante,
Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.
Assurez=vous de toujours lire tousles messages de securit6 et de vous y conformer.
Voici le symbole d'alerte de s6curit6.
Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de deces et de blessures graves
& vous eta d'autres.
Tous les messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces roots signifient :
Risque possible de d6ces ou de blessure grave si
vous ne suivez pas imm_diatement les instructions,
Risque possible de d_c_s ou de blessure grave
si vous ne suivez pas les instructions.
Tousles messages de s_curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de
blessure et ce qui peut se produire en cas de non=respect des instructions.
IMPORTANTES INSTRUCTIONS DE Si_CURITE
AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la
laveuse, suivre les precautions fondamentales dont les suivantes :
[] Lire toutes les instructionsavant d'utiliser la laveuse.
[] Ne pas laver des articles qui ont et6 nettoy6s ou
lav6s avec de I'essence ou imbib6s d'essence,
solvants de nettoyage & sec, ou autres substances
inflammables ou explosives; ces substances
peuvent 6mettre des vapeurs susceptibles de
s'enflammer ou d'exploser.
[] Ne pas ajouter d'essence, solvant de nettoyage &
sec ou autre produit inflammable ou explosif dans
I'eau de lavage. Ces substances peuvent emettre
des vapeurs susceptibles de s'enflammer ou
d'exploser.
[] Dans certaines conditions, de I'hydrog_ne gazeux
peut se former darts un circuit d'eau chaude qui n'a
pas 6t6 utilis6 pendant 2 semaines ou plus. LE GAZ
HYDROG#NE EST EXPLOSIBLE. Si le circuit d'eau
chaude n'a pas 6t6 utilis6 pendant une telle p6riode,
avant d'utiliser la laveuse, ouvrir tousles robinets
d'eau chaude et laisser I'eau s'6couler pendant
plusieurs minutes par chaque robinet. Ceci
permettra 1'6vacuation de I'hydrog_ne gazeux
accumul6. Comme ce gaz est inflammable, ne pas
fumer ou utiliser une flamme nue au cours de cette
p6riode.
[] Ne pas laisser des enfants jouer sur ou &I'interieur de la
laveuse. Bien surveiller les enfants Iorsque la laveuse est
utilisee & proximite d'enfants.
[] Avant de mettre la laveuse au rebut ou hors de service,
enlever la porte ou le couvercle.
[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de
la laveuse Iorsque le tambour, la cuve ou I'agitateur est en
mouvement.
[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle
serait exposee aux intemperies.
[] Ne pas modifier les organes de commande.
[] Ne pas reparer ou remplacer un composant quelconque de
la laveuse, ni entreprendre une operation de service, si ce
n'est specifiquement recommande dans ce manuel ou darts
un manuel d'instructions de reparations destine & I'utilisateur;
il est alors essentiel que la personne concernee comprenne
ces instructions et soit competente pour les executer.
[] Pour les instructionsde liaison & la terre, voir "Specifications
electriques" dans les instructionsd'installation.
CONSERVEZ CES INSTRUCTIONS
Avertissements de la proposition 65 de I'E'-_-tatde Californie :
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'!_tat de Californie pour 6tre & I'origine de
cancers.
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'#:tat de Californie pour 6tre b,I'origine de
malformations et autres deficiences de naissance.
18
QUOi DE NEUF SOUS LE COUVERCLE?
Nettoyer avec moins d°eau
Laveuse traditionnelle de
type agitateur
Laveuse & faible consommation
d'eau avec impulseur
La nouveaut6 la plus flagrante de cette nouvelle laveuse est
son systeme de lavage & faible consommation d'eau avec
impulseur. La laveuse ajuste automatiquement le niveau d'eau
en fonction de la taille de la charge - nul besoin de s61ecteur de
niveau d'eau.
D6tect[on automat[que
de taHOede charge
Une fois que I'on d6marre le programme, le couvercle se
verrouille et la laveuse entame un processus de d6tection pour
d6terminer le niveau d'eau appropri6 a la charge. Cela peut
prendre plusieurs minutes avant que I'eau ne soit ajout6e. Voir
la description pas-a-pas dans la section "T6moins lumineux des
programmes".
Vous entendrez le moteur faire tourner le panier par de brefs
mouvements d'impulsion pour bien imbiber la charge. Cette
m6thode de lavage avec faible consommation d'eau utilise
moins d'eau et d'6nergie qu'une laveuse traditionnelle de type
agitateur.
Cho[x du d@ergent appropri6
Utiliser uniquement des d6tergents Haute efficacit&
Uemballage portera la mention "HE" ou "High Efficiency" (haute
efficacit6). Un lavage avec faible consommation d'eau produit
un exces de mousse avec un d6tergent non HE ordinaire. IIest
probable que I'utilisation d'un d6tergent ordinaire prolongera la
dur6e des programmes et r6duira la performance de ringage.
Ceci peut aussi entrainer des d6faillances des composants et
une moisissure perceptible. Les d6tergents HE sont congus
pour produire la quantit6 de mousse ad6quate pour le meilleur
rendement. Suivre les recommandations du fabricant pour
d6terminer la quantit6 de d6tergent a utiliser.
Utiliser uniquement un detergent Haute efficacite (HE).
Pour un meilleur rendement, il est recommand6 de d6poser les
v_tements en vrac et de fagon uniforme le long du plateau de
lavage.
_, mesure que la laveuse imbibe et d6place la charge, les
v_tements se tassent dans le panier. Ceci est normal et ne
signifie pas que I'on doive rajouter des v_tements.
IMPORTANT : Le panier de la laveuse ne sera pas rempli d'eau,
comme avec votre pr6c6dente laveuse de type agitateur.
Nettoyage concentr6
Le systeme de lavage & faible consommation d'eau signifie un
lavage concentr& Plut6t que de diluer du d6tergent comme
dans une laveuse de type agitateur, cette laveuse libere le
d6tergent directement sur les endroits souill6s.
Sons normaux pr6visibMes
Au cours des diff@ents stades du programme de lavage, vous
entendrez peut-_tre des bruits que votre laveuse pr6c6dente
ne produisait pas. Par exemple, vous entendrez peut-6tre
un cliquetis au d6but du programme Iorsque le systeme de
verrouillage du couvercle effectue un test automatique. On
entendra diff@ents bourdonnements et bruits de frottements
rythmiques & mesure que I'impulseur d6place la charge. Parfois,
il est possible que la laveuse soit completement silencieuse,
Iorsqu'elle d6termine le niveau d'eau ad6quat ou qu'elle laisse
tremper les v_tements.
19
TABLEAU DE COMMANDE ET CARACTERISTIQUES
cold
t bulky/ norraa_[
sheets
coot
mediumheavy
sol[ level wash temp
O
soakS\
BRAV_ MCT Mayta#Corrqrnerda[fechnooSy
wrinkle control
i
off on
\ _ hand wash "_ _
_I cold wash
extra rinse
Certaines caract6ristiques et options ne sent pas disponibles sur certains modeles.
Uapparence des appareils peut varier.
SOiL LEVEL (niveau de salet6}
S61ectionner le r6glage le plus adapt6 &votre charge. Pour
les tissus tr_s sales et robustes, s61ectionner Extra Heaw
Soil Level (tr_s niveau de salet6 important) pour prolonger la
dur6e de lavage si n6cessaire. Pour les tissus peu sales et
d61icats, s61ectionner Light Soil Level (niveau de salet6 faible)
pour abr6ger la dur6e de lavage si n6cessaire. Le r6glage de
niveau de salet6 faible aidera a r6duire I'emm_lement et le
froissement.
i
off on
fabricsoffener
BOUTON START/PAUSE/UNLOCK (raise en
rnarche/pause/d6verrouiflage}
Appuyer sur ce bouton pour d6marrer le programme
WASH TEMP (temp6rature de lavage)
Lafonction WASH TEMP (temp6raturede lavage)d6tecte et
-s61ectionn6, puis appuyer de nouveau pour suspendre
le programme et d6verrouiller le couvercle. Appuyer pendant
3 secondes pour annulet un programme.
REMARQUE : Si la laveuse tourne, le couvercle peut mettre
quelques minutes a se d6verrouiller. Appuyer pendant
3 secondes pour annulet un programme.
TE_MOINS LUMINEUX DES PROGRAMMES
Lest6moins lumineux indiquent la progression du
O
O
maintient une temp6rature uniforme de I'eau en r6gulant le
d6bit d'arriv6e d'eau chaude et d'eau froide.
S61ectionner une temp6rature de lavage en fonction du type
de tissu et de salet6 a laver. Pour des r6sultats optimaux,
suivre les instructions sur 1'6tiquette du v_tement et utiliser
la temp6rature d'eau de lavage la plus chaude possible qui
reste sans danger pour le tissu.
• Sur certains modeles et pour certains programmes, les
temp6ratures utilis6es pour I'eau chaude et I'eau tiede
peuvent _tre inf6rieures aux temp6ratures utilis6es par
votre pr6c6dente laveuse.
• M_me avec un lavage a I'eau froide, il est possible que
de I'eau tiede soit ajout6e a la laveuse pour maintenir une
temp6rature minimale.
BOUTON DE PROGRAMME DE LAVAGE
Utiliser le bouton de programme de lavage pour s61ectionner
les programmes disponibles sur la laveuse. Tourner le
bouton de programme pour s61ectionner un programme
correspondant a la charge de linge. Voir "Guide de
programmes" pour des descriptions d6taill6es.
OPTIONS DE PROGRAMMES
IIest possible d'ajouter les options suivantes a la plupart des
programmes.
EXTRA RINSE (ringage suppl6mentaire)
On peut utiliser cette option pour ajouter
automatiquement un second rin(;age a la plupart des
programmes.
FABRIC SOFTENER ADDED
(ajout d'assouplissant pour tissu}
Le "On" de cette option dolt _tre s61ectionn6 si I'on utilise
de I'assouplissant pour tissu.
programme. A chaque 6tape du processus, il est possible
que I'on remarque des pauses ou des sons diff6rents de
ceux des laveuses ordinaires.
SENSING (d6tection)
seesieg wash rinse spie de_e _idi_cked
Lorsqu'on appuie sur le bouton START/Pause/Unlock
(Mise en marche/pause/d6verrouillage), la laveuse
effectue un test automatique sur le m6canisme de
verrouillage du couvercle. On entend un d6clic, le panier
effectue un 16get tour, et le couvercle se d6verrouille
brievement avant de se verrouiller a nouveau.
Une fois le couvercle verrouill6 pour la deuxieme fois, la
laveuse utilise des essorages lents et courts pour estimer
le volume de la charge. Ces essorages de d6tection
peuvent prendre 2 a 3 minutes avant que de I'eau ne soit
ajout6e a la charge et les essorages peuvent 6mettre
un bourdonnement. Si le t6moin lumineux de d6tection
est allum6, cela signifie que la laveuse fonctionne
correctement. On entend le moteur qui fait tourner
le panier par de de courtes impulsions pour mouiller
I'int6gralit6 de la charge. La laveuse d6place ensuite
brievement la charge, fait une pause pour permettre
&I'eau de tremper la charge, et continue a ajouter de
I'eau. Ce processus peut se r6p6ter jusqu'& ce que la
quantit6 d'eau correcte ait 6t6 ajout6e a la charge. II est
aussi possible que I'on entende de I'eau couler dans le
distributeur, ajoutant le d6tergent a la charge.
REMARQUE : Eviter d'ouvrir le couvercle pendant la
d6tection de la charge. Le processus de d6tection reprend
depuis le d6but quand la laveuse est remise en marche.
Le t6moin de d6tection peut s'allumer 6galement Iors des
6tapes de trempage et de lavage du programme. Ceci est
normal.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Maytag 7MMVWH450DW0 Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
dans d''autres langues
- English: Maytag 7MMVWH450DW0 User guide