Fulgor Milano F4IT30S2 Manuel utilisateur

Marque: Fulgor Milano

Modèle: F4IT30S2

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Ce manuel convient également à

F4IT24S2

IT USE & CARE MANUAL

FR GUIDE D’UTILISATION ET D’ENTRETIEN

ES MANUAL DE USO Y CUIDADO

F4IT24B2

F4IT24S2

F4IT30B2

F4IT30S2

INDUCTION HOB

PLAQUE DE CUISSON

À INDUCTION

PLACA INDUCCION

TABLE OF CONTENTS

PAGE

Warnings For Electrical Connection 2

1 - Safety Instructions 3

Cooktop Safety 3

Personal Safety 4

2 - Models and Part Identication 5

3 - How Induction Heating Works 6

Induction 6

Operating principle 6

4 - Induction Cooktop Operation 7

Before using the cooktop for the first time 7

Power Sharing 7

Cookware “noise” 7

5 - User instructions 9

Use 9

Pan detection 9

Residual heat indicator 9

Protection in the event of accidental switching on

Precautions 10

Pans 10

Maintenance 10

Turning the cooktop on and off 10

Acoustic signal (buzzer) 10

TABLE OF CONTENTS

PAGE

Turning on a cooking area 10

Turning off a cooking area 11

Power level 11

Booster and power management 11

Automatic preheating (or “heat-up” function) 11

Activating automatic heating (or “heat-up”

function) 11

Special functions (low temp) 11

Control lock (child safety) 11

Deactivating control lock 11

Key 12

Pause 12

Deactivating Pause 12

Timer function 12

Independent timer 12

Turning off/changing the timer 12

Programming the timer for the cooking areas 13

Error codes 13

6 - Troubleshooting 14

7 - Assistance or Service 15

Service Data Record 15

Pay attention to these symbols present in this

manual:

WARNING

• This is the safety alert symbol. This symbol alerts you to

potential hazards that can kill or hurt you and others.

• You can be killed or seriously injured if you don’t follow

these instructions.

READ AND SAVE THESE INSTRUCTIONS.

Warnings For Electrical Connection

WARNING

• Installation and service must be performed by a qualified

installer or service agency.

• The models may be powered at 240V or 208V.

CAUTION

• Always disable the electrical supply source before

servicing this unit.

• For personal safety, this appliance must be properly

grounded.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Note: This equipment complies with part 18 of the FCC Rules.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antennae.

• Increase the distance between the equipment and

receiver.

• Connect the equipment into an outlet or a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

WARNING

Persons with a pacemaker or similar medical device should

exercise caution when using or standing near an induction

unit while it is in operation. The electromagnetic field may

affect the working of the pacemaker or similar medical

device. It is advisable to consult your doctor or the pacemaker

manufacturer about your particular situation.

1 - Safety Instructions

Cooktop Safety

WARNING

Proper Installation

• Be sure your appliance is properly installed and grounded

by a qualified technician.

Never Use Your Appliance for Warming or

Heating the Room

Do Not Leave Children Alone

• Children should not be left alone or unattended in area

where appliance is in use.

They should never be allowed to sit or stand on any part

of the appliance.

Wear Proper Apparel

• Loose-fitting or hanging garments should never be worn

while using the appliance.

User Servicing

• Do not repair or replace any part of the appliance

unless specifically recommended in the manual. All other

servicing should be referred to a qualified technician.

Storage in or on Appliance

• Flammable materials should not be stored in an oven or

near surface units.

Do Not Use Water on Grease Fires

• Smother fire or flame or use dry chemical or foam-type

extinguisher.

Use Only Dry Potholders

• Moist or damp potholders on hot surfaces may result in

burns from steam. Do not use a towel or other bulky cloth.

Never Leave Surface Units Unattended at High

Heat Settings

• Boil over causes smoking and greasy spillovers that may

ignite.

WARNING

• Do not place metallic objects such as knives, forks, spoons,

and lids on the cooktop surface since they can get hot.

Do Not Cook on Broken Cook-Top

• If cook-top should break, cleaning solutions and spillovers

may penetrate the broken cooktop and create a risk of

electric shock. Contact a qualified technician immediately.

Clean Cook-Top With Caution

• If a wet sponge or cloth is used to wipe spills on a hot

cooking area, be careful to avoid steam burn. Some

cleaners can produce noxious fumes if applied to a hot

surface.

IMPORTANT INSTRUCTION

Please read all instructions before using this appliance.

Personal Safety

WARNING

To reduce the risk of injury to persons, in the

event of a grease re, observe the following:

• Grease is flammable and should be handled carefully.

• Do not use water on grease fires.

• Never pick up a flaming pan. Smother with a baking sheet

or flat, metal tray.

• Flaming grease outside of utensil can be extinguished with

baking soda or, if available, a multipurpose dry chemical

or foam type extinguisher.

• Let fat cool before attempting to handle it.

• Wipe up spill-over immediately.

• If you are “flaming” liquors or other spirits under an

exhaust, turn the fan off. The draft could cause the flames

to spread out of control.

• Never leave the surface area unattended at high heat

setting. Boil over cause smoking and greasy spill over,

which may ignite.

CAUTION

Do not allow aluminum foil, plastic, paper or cloth to come

in contact with a hot Surface. Do not allow pans to boil dry.

• Be careful to prevent burns. If the flames do not

go out immediately, evacuate and call the re

department.

• Always have a working smoke detector near the kitchen.

• Leave the hood ventilator on when flambéing food only if

there is smoke without ames.

Use an extinguisher only if

• You know you have a Class ABC extinguisher, and you

already know how to operate it.

• The fire is small and contained in the area where it started.

• The fire department is being called.

• You can fight the fire with your back to an exit.

• Never use water on cooking fires.

• In the event that personal clothing catches fire, drop and

roll immediately to extinguish flames.

WARNING

To reduce the risk of burn injuries during cooktop

use, observe the following:

• Never use the cooktop to warm or heat a room.

• Children or pets should not be left alone or unattended in

an area where appliances are in use. They should never

be allowed to sit or stand on any part of the appliance.

CAUTION

Do not store items of interest to children in cabinets above a

range or on the backguard of a range; children climbing on

the range to reach items could be seriously injured.

When using the cooktop

• Do not touch surface units or areas near units.

Surface areas may become hot enough to cause burns.

Surface elements may be hot even though they are dark in

color. During and after use, do not touch or let flammable

materials contact heating elements until they have had

time to cool.

2 - Models and Part Identiﬁcation

24” MODELS

F4IT24S2

Position 1 7” 7/8” (200 mm) - 2300W (Booster 3000W)

Position 2 5” 3/4” (145 mm) - 1400W (Booster 1850W)

Position 3 7” 7/8” (200 mm) - 2300W (Booster 3000W)

Position 4 5” 3/4” (145 mm) - 1400W (Booster 1850W)

Position 5 touch control

30” MODELS

F4IT30S2

Position 1 7” 7/8” (200 mm) - 2300W (Booster 3000W)

Position 2 6” 1/4” (160 mm) - 1400W (Booster 2100W)

Position 3 7” 7/8” (200 mm) - 2300W (Booster 3000W)

Position 4 6” 1/4” (160 mm) - 1400W (Booster 2100W)

Position 5 touch control

3 - How Induction Heating Works

Induction

Heating by induction is the most efficient form of cooking

available.

The heat is generated by an electromagnetic field, directly on

the bottom of the pan or pot used.

The surface which is free from contact remains virtually cold.

When the cooking time is up and the container is removed,

there is no residual heat. It is efficient become there is no waste

of energy due to dispersion, as happens with gas burners, it is

30 to 50% faster than normal hobs using HGL technology and

allows energy savings of up to 25%.

If liquid overflow from the container, it does not stick to the

surface of the hob, because this is just slightly warm.

Operating principle

This is based on the electromagnetic properties of most cooking

containers.

The electronic circuit governs the operation of the coil (inductor),

creating a magnetic field.

The heat is transmitted by the container to the food.

Te cooking process takes place as follows:

• minimum dispersion (high performance);

• the removal of the pan (simply lifting it) automatically stops

the system;

• the electronic system allows maximum flexibility and

precision of regulation.

1 - Recipient

2 - Induced current

3 - Magnetic field

4 - Inductor

5 - Electronic circuit

6 - Electricity supply

4 - Induction Cooktop Operation

Before using the cooktop for the rst

time

• All products are wiped clean with solvents at the actory to

remove any visible signs of dirt, oil, and grease which may

have remained from the manufacturing process.

• If present, remove all packing and literature from the cooktop

surface.

• Clean your glass top before the first time you use it. A

thorough cleaning with a glass top cleaner is recommended.

It only takes a minute and puts a clean, shiny coating on the

glass top before its initial use.

• There may be a slight odour during the first several uses: this

is normal and will disappear.

• Optimum cooking result depends on the proper cookware

being selected and used.

• The cooking surface will hold the heat and remain hot over

20 minutes after the elements have been turned off.

• The glass ceramic cooking surface is a durable material

resistant to impact but not unbreakable if a pan or other

object is dropped on it.

• Do nor allow pans to boil dry. This can damage the pan,

element and /or cooktop.

• Do not slide cookware across cooking surface it may scratch

the glass

4 burner cooktops with right and lift side (2) induction

generators.

Power Sharing

Four burner cooktops are divided into two separate

heating zones.

Five burner cooktops are divided into 3 zones.

One generator controls 2 elements, or two cooking zones

within a heating section share the power of one generator.

Power Sharing is activated when both elements in the same

cooking zone are activated and one element is set for Boost

(b). The element that is not set for Boost will change to a lower

power level. This is called Power Sharing.

Cookware “noise”

When using adjacent elements that are set at certain power

level setting, magnetic fields may interact and produce a low

whistle or intermitted “hum”. Pens that completely cover the

elements ring will produce less noise. A low “humming” noise

is normal particularly on high settings. These noises can be

reduced or eliminated by lowering or raising the power level

settings of one or both of elements.

In some cooking areas an internal diameter is indicated with

a lighter outline.

24” Wide Cooktop. Use the minimum size pan shown for

each cooking element.

Diameter pan size 24”

5” 1/8” (13.0 cm)

minimum diameter pan size

4” 5/16” (11.0 cm)

minimum diameter pan size

5” 1/8” (13.0 cm)

minimum diameter pan size

4” 5/16” (11.0 cm)

minimum diameter pan size

30” Wide Cooktop. Use the minimum size pan shown for

each cooking element..

Diameter pan size 30”

5” 1/8” (13.0 cm)

minimum diameter pan size

4” 5/16” (11.0 cm)

minimum diameter pan size

5” 1/8” (13.0 cm)

minimum diameter pan size

4” 5/16” (11.0 cm)

minimum diameter pan size

5 - User instructions

Residual heat indicator

This tells the user that the glass is at a dangerously high

heat in case of contract with the whole area over the

cooking zone. The temperature is determined using a

mathematical model and any residual heat is indicated

with an “H” by the corresponding seven-segment display.

Heating and cooling are calculated in relation to:

• the power level selected (from “0“ to “9“);

• the relay activation period.

After switching off the cooking zone, the corresponding display

shows an “H” until the temperature in the zone falls below

the critical level (≤ 60°C) in compliance with the mathematical

model.

Protection in the event of accidental

switching on

• If the electronic control sense continuous activation of a key

for about 10 sec. it switches off automatically. The control

gives off an acoustic error, warning the user of the presence

of an object on the sensors. The displays show the permanent

error code, which will be displayed as long as the electronic

control senses the error. If the cooking zone “burns”, an “H”

will appear on the display, alternating with the error signal.

• If no cooking zone is activated within 10 seconds of switching

on the touch control, the control returns to stand-by mode.

• When the touch control is on, the ON/OFF key takes priority

over all the other key, so the touch control can be switched

off at any time, even in the case of multiple or continuous

activation of the keys.

• In stand-by mode, continuous activation of the keys will

have no effect. However, before the electronic control can

be switched on again, it must acknowledge that no key is

active.

Use

First of all, position the pan in the chosen cooking area. The

absence of the pan display means the system cannot start.

Pan detection

A certainty which distinguishes the knowledgeable use of

technology in favour of the consumer.

3 4 5167 8 9 10 11

24 23 22 21 20 19 217 16 15 14 13 12

Parts

1Main ON/OFF 13 Timer for cooking area activation icon

2+ Timer 14 Cooking area level display

3- Timer 15 Cooking level illuminated bar

4Key on LED 16 On area indication

5Key on button 17 Melt function symbol

Pause on button 19 Timer (minutes/seconds) display

7Pause and Recall involuntary switch-off LED 20 Timer (minutes/seconds) display

8ON/OFF Heating area 21 Separator dot (hours/minutes)

9Minimum level activation cursor area 22 Timer display (hours/minutes)

Maximum level activation cursor area 23 Icon indicating minutes

11 Power Booster (b) activation cursor area 24 Independent timer icon

12 Bridge function on icon (Not present)

Precautions

• If there is even the tiniest crack in the ceramic glass surface,

immediately disconnect the hob from the electricity supply;

• during operation, move any magnetic materials such as

credit cards, computer disks, calculators, etc., away from

the area;

• never use cooking foil or rest products wrapped in foil

directly on the hob;

• metallic objects such as knives, forks, spoons and lids must

not be rested on the surface of the hob to prevent them from

heating up;

• when cooking with non-stick cookware, without using water

or oil, limit any preheating time to one or two minutes;

• when cooking foods which tend to stick to the bottom of

the pan, start at minimum power and gradually increase the

heat, stirring frequently;

• after use, turn off element manually (decreasing to “0”)

rather than relying on the pan detection sensor.

Pans

• If a magnet is attracted to the bottom of your cookware then

it is suitable for induction cooking;

• try to use pans declared as suitable for induction cooking;

• flat, thick-bottomed pans will perform most effectively;

• a 20 cm (8”) diameter saucepan can benefit from maximum

power;

• a small saucepan reduces the power but will not cause

energy dispersion. The use of cookware with a diameter of

less than 12 cm (3”) is not recommended;

• stainless steel cookware with multilayer bottom or ferrite

stainless steel if the bottom indicates: for induction;

• cast iron containers, better with an enamelled bottom to

avoid scratching the ceramic glass hob;

• containers made of glass, ceramic, terracotta, aluminium,

copper or non-magnetic stainless steel (austenitic) are

not recommended and are unsuitable unless using Fulgor

Milano’s adapter kit (INDUKIT).

YesNo No

Maintenance

Traces of foil, food residues, splashes of fat, sugar or very

sugary foods must be removed immediately from the hob using

a scraper to avoid damaging the hob surface. Then clean with

a proper ceran top cleaner and kitchen paper, rinse with water

and dry with a clean cloth. Never use abrasive sponges or

clothes and avoid using aggressive chemical cleansers such as

OVEN SPRAYS or STAIN REMOVERS. DO NOT USE STEAM

CLEANERS

Turning the cooktop on and off

The cooktop is turned on by pressing the “centre” On/Off

button (1), you will hear a short beep and the corresponding

led lights up. If a cooking zone is “hot”, the display will

alternate between “H” and “0”. After switching on, the touch

control remains active for 10 seconds. If you do not select either

a cooking zone or the times, the touch control automatically

returns to stand-by mode.

Acoustic signal (buzzer)

During use, the following activities are signalled by a buzzer:

• Normal pressing of the buttons with a short beep.

• Holding down buttons for more than 10 seconds with a long

intermittent sound (an error symbol is displayed and, if you

continue, the touch control is turned off).

Turning on a cooking area

Position a pot and touch an area of the cursor for the cooking

area where the pot is (8), slide your finger to the right to

increase the cooking level (10), or slide your finger to the left

to decrease it (9).

Turning off a cooking area

A single cooking area can be turned off directly by pressing

the (8) key for the cooking area that is working. Hot cooking

areas will be displayed with a letter “H”. You can turn off all

cooking areas immediately at any time using the power On/

Off button (1). If, during cooking, you inadvertently turn off

the surface while using the controls, you can turn it on again

with the On/Off button and you will have 6 seconds to press

the pause button (6) that will be indicated by the (7) flashing

of an indicator light above the button; doing so will turn the

surface on again with the same settings it had before it was

accidentally turned off.

Power level

The power level of the cooking area can be set from level 1

to level 9. A further level b (Power Booster) is available that

allows a very rapid heating of food and, therefore, saves you

time. The power level represented by an intermittent letter “A”

is the activation of the automatic heating function.

Booster and power management

The generator, with Booster enabled, provides an individual

cooking area power that is significantly higher than the rated

power; the display of the selected cooking area shows a “b”.

The Booster function can be activated by pressing at the end

of the cursor of the cooking area (11). The power increase is

different depending on the size of the cooking area:

1. For a cooking area with a diameter of 5 3/4” (145 mm),

the power goes from a level 9 of 1400 W to the Booster

level of 1850 W for 5 minutes.

2. For a cooking area with a diameter of 6” 1/4” (160 mm),

the power goes from a level 9 of 1400 W to the Booster

level of 2100 W for 5 minutes.

3. For a cooking area with a diameter of 7” 7/8” (200 mm),

the power goes from a level 9 of 2300 W to the Booster

level of 3000 W for 5 minutes.

If the cooking vessel is removed from the cooking area during

the Booster time, the Booster remains active and the Booster

time is not deactivated. With the Booster activated, changing

the value set with your finger in the cursor area deactivates

the Booster. The Booster function “b” can be activated in all

cooking areas, but priority is given to the last Booster activated,

reducing any other cooking levels.

24”-30” Power sharing table

LEFT RIGHT

b 8 7 b

7 b b 8

Automatic preheating (or “heat-up”

function)

This feature makes cooking easier by adding ‘boil and reduce’

functionality to the elements. The surface automatically heats

up at Full Power and then returns to the selected power level

after a certain time (see Table).

Activating automatic heating (or “heat-

up” function)

Press and hold an area of the cursor for the cooking area that

is working for about 3 seconds until you hear a beep (such as

1/3 of the length of the cursor area). For example: Select level

3 and activate the automatic heating function by pressing your

finger for 3 seconds. The corresponding display shows the

letter “A” alternating with “3”. With these settings, the cooking

surface heats the cooking area at the maximum level “9” for 2

minutes and then continues cooking level at level “3”.

Power livel Duration Automatic

Heating Function

(time in minutes)

Maximum time

elements will operate

at power setting (time

in minutes)

10m 40s 522

21m 12s 402

32m 318

42m 56s 258

4m 16s 210

67m 12s 168

72m 138

83m 12s 114

-90

-5

Special functions (low temp)

This function is available in each cooking area and its

activation is indicated by one of the icon 17. It is possible to

activate “cooking” levels:

1. Melting with a temperature of approximately 40˚C.

These temperatures are approximate and are greatly

dependent on the pot and the quantity of food.

After turning on the desired heating zone by pressing the key

(8), press the initial part of the cursor area (9) to activate

the function (MELT). Low temperature function operate for a

maximum of 2 hours.

Control lock (child safety)

It can only be activated when the appliance is on but no cooking

area is in operation. Simultaneously press the key button (5)

and the pause button (6) and then press the key button (5).

The letter “L” will appear on both displays for 10 seconds and

then they will turn off. When you try to turn on the cooking

surface with the On/Off button (1), the letters “L” will be

displayed and it will not be possible to cook.

Deactivating control lock

There are two types of unlocking:

1. Unlocking for one time only: To disable the function, turn

on the cooking surface and simultaneously press the pause

(6) and key (5) buttons. The letters L disappear and all

the zones are enabled. If you turn off the cooking surface

after use, when it is turned on again, the letters L will be

displayed to indicate that the surface is locked. Essentially,

the cooktop will be safety locked automatically whenever

not in use but the special key combination described above

will be needed each time to use.

2. Permanent unlocking: To disable the function permanently,

turn on the cooking surface and simultaneously press the

pause (6) and key (5) buttons. Then release these 2 buttons

and press the Pause button (6) again.

Key

This cooking surface allows setting a keypad lock using the

lock button (5). It may be useful to lock the keypad during

operation, for example for cleaning the control area or, in any

case, if you do not want to change any settings. The On/Off

button (1) remains functional.

Pause

This cooking surface allows setting a pause (6) during cooking

(which is useful, for example, when answering a phone call).

When this function is pressed, an LED lights above the button

and the symbol “II” is displayed in all the cooking areas and

the cooking settings and timers are frozen for a maximum of

10 minutes, after which the cooking surface turns off.

Deactivating Pause

Once activated, the function can be deactivated by pressing

the pause button (6) again. The LED for the pause setting turns

off and, within 10 seconds, you must slide your finger along

the cursor below the illuminated area (from left to right). This

allows the surface to resume cooking and the timer starts from

the same point at which it was stopped.

Timer function

NOTE: the timer is only intended as an acoustic advisor that

recalls the attention of the user.

Timers have no effect on the heating elements. Cooking

zones must always be stopped manually by touching

the corresponding [OFF] key.

There are two versions of the timer function:

• An independent timer from 1 to 59 minutes: it beeps when

the time has run out. This function is always available and is

indicated by the clock symbol (24) which is located between

the - and + buttons (the symbol may be less bright if another

cooking area timer has a remaining time that is less than that

set on the independent timer).

• A timer from 1 to 59 minutes for each cooking area: it

beeps when the time has run out. The cooking areas can be

programmed independently (the symbol may be less bright if

another cooking area timer has a remaining time that is less

than that set on the independent timer).

The type of timer activated is shown in the dedicated displays.

The timer with the least time is highlighted and the related clock

icon is brighter (13-24). The other timer settings are still active

and running, but the clock icon (13-24) will be less bright.

Another icon with the word “min” (23) appears when you set

times longer than 10 minutes. For example 0.11 indicates 0

hours and 11 minutes. The separator dot (21) flashes when

the timer is running, while the dot is static while the timer is

selected and thus modifiable.

Independent timer

• If the touch display is on, the independent timer can be

used by simultaneously pressing the + and - buttons. If all

the cooking areas are in position “0”, this is the only timer

available. The clock icon (24) will turn on and the display

will show “0.00”. If you do not select any button, the timer

deactivates within 5 seconds.

• The time setting (0-1hour.59min) can be changed in

increments of one minute with the + button from 0 to 99.

• Holding down the + or - button dynamically increases the

rate of change up to a maximum value, without beeps.

• If the + (or -) button is released, the rate of increase (decrease)

starts again from the initial value.

• The timer can be set by either continuously pressing the +

or - buttons or by pressing successively (with beeps).

After the timer is set, it begins to count down. The expiry of

the time is signalled by a beep or by the flashing of the timer

display, which will show “00”.

Turning off/changing the timer

• The timer can be changed or turned off at any time by turning

on the touch display again, if no cooking area is on, and

pressing the + and - buttons simultaneously to select the timer.

At this point, set it to “0” by pressing the - button, to turn it

off, or by pressing the + button to increase the time setting.

• The independent timer remains active even when the On/

Off button is pressed

Programming the timer for the cooking

areas

By turning on the touch display, you can program an

independent timer for each cooking area.

• At least one cooking area must be on and set to a certain

level.

• By pressing the + and - buttons simultaneously, you can

set a countdown for turning off the cooking area. There

are illuminated clock icons (13) next to the display of the

cooking area. To set the timer on a cooking area when there

are more than one cooking area on, you must press the +

and - buttons simultaneously. You will note that the clock icon

will light and move to successive cooking areas each time

you simultaneously press the + and - buttons.

• When the timer of the cooking area is selected, the related

clock icon near the display becomes brighter (13). The

timers programmed for each cooking zone remain active.

• Other functions of the timer are the same as the independent

timer. To increase the time, use the + (plus) button.

• The beeping and flashing of the display stops:

a- Automatically after 2 minutes.

b- When you press the + or - buttons, the timer display turns off.

Error codes

Error codes are displayed by the 7-segment display with “E” or “ER” plus the error number.

Error message Description Possible error reason Troubleshooting

“flash” Control is detecting a button

being activated for more than 10

seconds.

Water or cooking utensils on

the glass above the control unit Cleaning of the operational

surface

Er 22 Defective Key evaluation . Control

unit cuts off after 3.5 - “7.5 sec. Short-circuit or no continuity in

the range of the key evaluation Exchange control unit

Er20 Flash-failure Faulty microcontroller Exchange control unit

Er36 NTC value is not

within its specification

(value < 200mV or > 4.9V;

control unit cuts off

Short-circuit or cut-off at NTC Exchange control unit

Er31 Configuration data incorrect Configuration of induction

necessary New Configuration

Er47 Communication error between TC

and induction None or faulty communication! Ensure that connection cable

is plugged on correctly and

functional.

E2 Overheating of the induction coils Cooling down necessary

U400 Secondary voltage of the power

unit too high (primary > 300V).

Control unit cuts off after 1 sec

releasing a permanent tone.

Control unit is wrongly

connected Connect to correct mains

voltage

E5 No communication between

User Interface and Induction

Generator

Exchange Induction Generator

E6 Power supply voltage is out of

range (voltage and/or

frequency)

Exchange power unit

E9 Coil temperature sensor defective Exchange temperature sensor

6 - Troubleshooting

Problem Cause Possible Remedy

Nothing works

Cooktop not connected to proper electrical

circuit. Have electrician verify that the proper rated

cooktop voltage is being supplied to the

cooktop.

Fuse is blown or circuit breaker is tripped. Have electrician replace fuse or reset circuit

breaker.

No electricity to the cooktop. Have electrician check your power supply.

Cooktop is in lockout mode. Unlock cooktop.

Heating elements do not heat

properly Improper cookware is being used. Select proper cookware as outlined in the

Cooktop Operation section of this manual.

Glass ceramic surface is see-

through or appears to be red

in color

Under direct or bright lighting, you will

sometimes be able to see through the glass

and into the chassis due to its transparent

quality. You may also notice a red tint under

these conditions.

These are normal properties of black ceramic

glass panels.

7 - Assistance or Service

Service Data Record

For authorized service or parts information see

“FULGOR WARRANTY for Home Appliances”.

The location of the serial tag is below the cooktop box. Now

is a good time to write this information in the space provided

below. Keep your invoice for warranty validation.

Service Data Record

Model Number _________________________________

Serial Number __________________________________

Date of Installation or Occupancy __________________

Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call.

If you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model and serial number of your appliance.

This information will help us to better respond to your request.

TABLE DES MATIERES

PAGE

Avertissements pour la connexion électrique 2

1 - Précaution de Sécurité 3

Securite de la Table de Cuisson 3

Securite Personnelle 4

2 - Modèles et nomenclature des pièces 5

3 - Fonctionnement du chauffage par

induction 6

Induction 6

Principe de fonctionnement 6

4 - Fonctionnement de la Table de Cuisson 7

Avant D’utiliser La Table De Cuisson Pour La

Premiere Fois 7

Partage de Puissance 7

Batterie de cuisine «bruyante» 7

5 - Instructions pour l’utilisateur 9

Utilisation 9

Détection du récipient 9

Indicateur de chaleur résiduelle 9

Protection en cas d’allumage involontaire 9

Précautions 10

Récipients 10

Entretien 10

Turning the cooktop on and off 10

Signal sonore (vibreur) 10

TABLE DES MATIERES

PAGE

Allumage d’une zone de cuisson 10

Extinction d’une zone de cuisson 11

Niveau de puissance 11

Booster et gestion de la puissance 11

Réchauffage automatique

(ou fonction «heat-up») 11

Activer le réchauffage automatique

(ou fonction “heat-up”) 11

Fonction de pontage (pour grandes casseroles) 11

Special functions (low temp) 12

Blocage des commandes (sécurité enfants) 12

Désactivation du verrou de contrôle 12

Clé 12

Pause 12

Désactivation Pause 12

Fonction de Minuterie 12

Minuterie autonome 13

Éteindre/modifier la minuterie 13

Programmation de la minuterie :

pour les zones de cuisson 13

Indications d’erreur 14

6 - Pannes 15

7 - Assistance ou Service Après-Vente 16

Données de Service 16

Veuillez prêter attention à ces symboles que vous

rencontrerez dans ce manuel:

AVERTISSEMENT

• Ce symbole signifie que la sécurité est en danger. Il signale

les risques potentiels qui peuvent entraîner la mort ou des

blessures à l’operateur ou aux autres.

• Si vous ne suivez pas ces instructions à la lettre, vous

courez le risque de mourir ou d’être sérieusement blessé.

BIEN LIRE CES INSTRUCTIONS ET LES CONSERVER.

Avertissements pour la connexion

électrique

AVERTISSEMENT

• L’installation et l’entretien de l’appareil doivent être exécutés

par un installateur qualifié ou un boreau technique.

• Les modèles peuvent êre actionnés à 240V ou

à 208V.

ATTENTION

• Toujours désactiver la source d’alimentation électrique

avant d’entretenir cet appareil.

• Pour des raisons de sécurité personnelle, cet appareil doit

être mis à la terre correctement.

Les changements ou les modifications non explicitement

approuvés par la partie garante de la conformité risquerait

d’annuler le droit de l’utilisateur à employer l’équipement.

Note: Cet équipement est conforme à la partie 18 des Règles

de la FCC. Cet appareil génère, utilise et peut émettre

de l’énergie sous la forme de fréquence radio et,

s’il n’est pas installé et utilisé en conformité avec les

instructions, il peut provoquer des interférences nocives

sur les communications radio. Cependant, il n’existe

aucune garantie que des interférences se produiront

dans une installation particulière. Si cet appareil

provoque des interférences nocives sur la réception

radio ou télévision, ce qui peut être détecté en mettant

l’appareil sous et hors tension, l’utilisateur est encouragé

à essayer de corriger ces interférences en appliquant

l’une ou plusieurs des measures suivantes :

• Réorientez ou déplacez l’antenne réceptrice.

• Augmentez la distance entre l’appareil et le récepteur.

• Branchez l’appareil dans une prise ou un circuit

différent de celui sur lequel est branché le récepteur.

• S’adresser au revendeur ou à un technicien radio/

TV expérimenté.

AVERTISSEMENT

Les personnes avec un stimulateur cardiaque ou un dispositif

médical similaire doivent redoubler de prudence lors

de l’utilisation d’une unité à induction ou à proximité de

l’appareil en fonctionnement. Le champ électromagnétique

peut affecter la bonne marche du stimulateur cardiaque ou

du dispositif médical similaire. Il est conseillé de consulter

votre médecin ou le fabricant du stimulateur sur votre

situation particulière.

La page charge ...

Fulgor Milano F4IT30S2 Manuel utilisateur

Marque: Fulgor Milano

Modèle: F4IT30S2

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Ce manuel convient également à

F4IT24S2

Télécharger le PDF

rapport

dans d''autres langues

English: Fulgor Milano F4IT30S2 User manual
español: Fulgor Milano F4IT30S2 Manual de usuario

Fulgor Milano F4IT30S2 Manuel utilisateur

Ce manuel convient également à

Fulgor Milano F4IT30S2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents