Remington Chainsaw Electric Chain Saw Manuel utilisateur

Step

1

Loose Chain...

Step

2a

Step

3

Step

2b

®

ELECTRIC CHAIN SAW OWNER’S MANUAL

IMPORTANT!

Failure to follow these instructions when tensioning saw chain

will damage saw and void the warranty. For additional informa-

tion see owner’s manual or call 1-800-858-8501.

Make sure chain moves freely around

guide bar then tighten nut.

L

O

S

E

N

Loosen nut...

If chain becomes loose around guide bar, allow chain to cool then...

T

I

G

H

T

E

N

Turn chain tensioning screw clock-

wise to tension saw chain...

T

I

G

H

T

E

N

WARNING: Unplug saw

and allow chain to cool before

tensioning.

New saw chains will stretch.

Check chain tension frequently

when first used and tighten

when chain becomes loose

around guide bar.

Pull chain to check tension. Guide

links should not come out of guide

bar groove...

See pages 8 and 9 for additional information.

ENGLISH

FRANÇAISESPAÑOL

Approx. 1/8"

Guide Bar

®

IMPORTANT: Read and understand this manual before assem-

bling or operating this chain saw. Improper use of saw can cause

severe injury. Keep this manual for future reference.

MODELS: M12510US, M15012US, M15014US, M15014AS, M30016US,

M30016AS, M30016AW, M35016UW, M35016AW

ELECTRIC CHAIN SAW

OWNER’S MANUAL

ENGLISH

2

113005

www.desatech.com

Contents

IMPORTANT SAFETY INFORMATION .............................................................................. 3

Before Operating Saw ....................................................................................................................... 3

While Operating Saw ......................................................................................................................... 3

Kickback ............................................................................................................................................

4

Maintenance and Storage of Chain Saw ...........................................................................................

5

UNPACKING ....................................................................................................................... 6

PRODUCT IDENTIFICATION .............................................................................................

6

CHAIN SAW NAMES AND TERMS ....................................................................................

6

ASSEMBLY .........................................................................................................................

7

SAW CHAIN TENSION ADJUSTMENT ..............................................................................

8

OPERATING CHAIN SAW ..................................................................................................

9

Filling Oil Tank ................................................................................................................................... 9

Oiling Chain ....................................................................................................................................... 9

Clearing sprocket cover of debris ....................................................................................................

10

Extension Cords .............................................................................................................................. 10

Cutting with the Chain Saw .............................................................................................................

11

Felling a Tree (Cutting Down a Tree) ...............................................................................................

11

Limbing a Tree .................................................................................................................................

12

Bucking a Log ..................................................................................................................................

13

Trimming a Tree (Pruning) ............................................................................................................... 13

CLEANING AND MAINTENANCE ................................................................................... 15

Cleaning Saw Body ......................................................................................................................... 15

Care of Guide Bar ........................................................................................................................... 15

Sharpening Saw Chain ....................................................................................................................

15

Replacing Saw Chain ......................................................................................................................

16

STORAGE ......................................................................................................................... 17

TECHNICAL SERVICE .....................................................................................................

17

REPLACEMENT PARTS AND ACCESSORIES ...............................................................

17

REPAIR SERVICE .............................................................................................................

17

Warranty Service ............................................................................................................................. 17

Non-Warranty Service .....................................................................................................................

17

TROUBLESHOOTING ...................................................................................................... 18

WARRANTY INFORMATION ............................................................................................

19

ILLUSTRATED PARTS BREAKDOWN/DESGLOSE ILUSTRADO DE PARTES/SCHÉMA

DES PIÈCES ..................................................................................................................... 62

PARTS CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE PIÈCES .....................................

65

3

113005

www.desatech.com

ENGLISH

IMPORTANT SAFETY

INFORMATION

BEFORE OPERATING SAW

1. Read and understand this owner’s manual before

operating chain saw.

2. Watch what you are doing. Use common sense.

Do not operate saw when you are tired.

3. Use chain saw for cutting wood only. Do not use

chain saw for purpose not intended. Do not use

for cutting plastic, masonry, etc.

4. Only well-instructed adults should operate chain

saw. Never allow children to operate chain saw.

5. Use only electrical voltage noted on model plate

of chain saw.

6. Use only extension cords marked for outdoor use.

See page 10 for extension cord requirements.

7. Do not operate chain saw

• while under the inﬂuence of alcohol, medica

-

tion, or drugs

• in rain or in damp or wet areas

• where highly ﬂammable liquids or gases are

present

• if saw is damaged, adjusted wrong, or not fully

and securely assembled

• if trigger does not turn saw on and off. Chain

must stop moving when you release trigger.

Have faulty switch replaced by authorized ser

-

vice center (see Technical Service, page 17).

• while in a hurry

• while in tree or on a ladder unless trained to

do so

8. Wear snug-ﬁtting clothes when operating chain

saw. Do not wear loose clothing or jewelry. They

can get caught in moving saw chain.

9. Wear the following safety gear when operating

chain saw.

• heavy-duty gloves (wear rubber gloves when

working outdoors)

• steel-toed safety footwear with non-skid soles

• eye protection such as safety glasses, goggles,

or face screen

READ ALL INSTRUCTIONS.

Make sure you read and understand all in

-

structions in Important Safety Information

on pages 3 through 5. Improper use of this

chain saw can cause severe injury or death

from ﬁre, electrical shock, body contact

with moving chain, or falling wood.

WARNING: When using an electric

chain saw, basic safety precautions

should always be followed to reduce the

risk of ﬁre, electric shock, and injury to

persons, including the following:

• safety hard hat

• ear mufﬂers or ear plugs

• hair covering to contain long hair

• face or dust mask (if working in dusty areas)

10. Before cutting, always provide the following:

• clear work area

• secure footing

• planned retreat path from falling tree

11. Inspect tree before cutting down. Make sure there are

no dead limbs or branches that may fall on you.

12. To reduce the risk of electric shock, this saw has a

polarized plug (one blade is wider than the other).

This plug will ﬁt in a polarized outlet only one

way. If the plug does not ﬁt fully in the outlet of

your extension cord, reverse the plug. If it still

does not ﬁt, a polarized extension cord will be

necessary. Do not change the plug in any way.

WHILE OPERATING SAW

1. Stay alert. Use common sense while operating

chain saw.

2. Keep work area clean. Cluttered areas invite

injuries.

3. Be aware of extension cord while operating chain

saw. Be careful not to trip over cord. Keep cord

away from chain and operator at all times.

4. Keep children, animals, and bystanders away

from chain saw and extension cord. Only chain

saw user should be in work area.

5. Do not cut down a tree unless you are trained or

have expert help.

6. If two or more persons perform bucking and fell

-

ing operations at the same time, provide plenty

of distance between operations. Provide distance

of at least twice the height of tree being felled.

7. Secure wood you are cutting by using clamps or

chocks.

8. Grip chain saw ﬁrmly with both hands. Never

operate chain saw with one hand. Never use hand

guard as handle.

9. Keep ﬁnger off trigger until ready to make cut.

10. Before starting chain saw, make sure chain is not

touching anything.

11. To guard against electrical shock, avoid body

contact with grounded objects such as pipes,

fences, and metal posts.

12. Keep all parts of body away from chain when

saw is running.

13. Do not force chain saw while cutting. Apply light

pressure. It will do the job better and safer at the

rate for which it was intended.

14. Cut small brush and saplings with extreme care.

Slender material may catch in chain and be

whipped toward you. This could also pull you

off balance.

Continued

4

113005

www.desatech.com

IMPORTANT SAFETY

INFORMATION

Continued

WARNING: Kickback may occur when

the nose or tip of the guide bar touches

an object, or when the wood closes in

and pinches the saw chain in the cut.

Tip contact in some cases may cause a

lightning fast reverse reaction, kicking the

guide bar up and back towards the opera

-

tor. Pinching the saw chain along the top

of the guide bar may push the guide bar

rapidly back towards the operator. Either

of these reactions may cause you to lose

control of the saw which could result in

serious injury to user.

KICKBACK

15. When cutting limb or tree trunk that is under

tension, use extreme caution. Be alert for wood

springing back. When wood tension is released,

limb could spring back and strike operator caus

-

ing severe injury or death.

16. Carry chain saw from one place to another

• with saw stopped and unplugged

• by holding front handle (never use hand guard

as handle)

• with ﬁnger off trigger

• with guide bar and chain to rear

Kickback Safety Devices On This Saw

This saw has a low-kickback chain and reduced

kickback guide bar. Both items reduce the chance of

kickback. Kickback can still occur with this saw.

Follow assembly instructions on pages 7 and 8. Do

not remove front hand guard. Do not replace front

hand guard with substitute.

The following steps will reduce the risk of kickback.

• Use both hands to grip saw while saw is running.

Use ﬁrm grip. Thumbs and ﬁngers must wrap

around saw handles.

• Keep all safety items in place on saw. Make sure

they work properly.

• Do not overreach or cut above shoulder height.

• Keep solid footing and balance at all times.

• Stand slightly to left side of saw. This keeps your

body from being in direct line with chain.

• Do not let guide bar nose touch anything when

chain is moving (see Figure 1).

WARNING: Some dust created by

power sanding, sawing, grinding, drill

-

ing, and other construction activities

contains chemicals known (to the state

of California) to cause cancer, birth de

-

fects, or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and ce

-

ment and other masonry products

• arsenic and chromium from chemically-

treated lumber

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure to

these chemicals: work in a well ventilated

area, and work with approved safety

equipment, such as those dust masks

that are specially designed to ﬁlter out

microscopic particles.

WARNING: This product contains

chemicals known to the State of Cali

-

fornia to cause cancer or birth defects,

or other reproductive harm.

Figure 1 - Kickback Hazard Example: Do Not Let

Nose of Guide Bar Touch Object While Chain

is Moving

90° Quadrant

Do Not Let Guide

Bar Touch Here

Direction

5

113005

www.desatech.com

ENGLISH

IMPORTANT SAFETY

INFORMATION

Continued

• Never try cutting through two logs at same time.

Only cut one log at a time.

• Do not bury guide bar nose or try plunge cut (boring

into wood using guide bar nose).

• Watch for shifting of wood or other forces that may

pinch chain.

• Use extreme caution when reentering a previous cut.

• Use low-kickback chain and guide bar supplied

with this chain saw. Only replace these parts with

chains and guide bars listed in this manual.

• Never use dull or loose chain. Keep chain sharp

with proper tension.

Saw Maintenance and Kickback Safety

Follow maintenance instructions in this manual. Proper

cleaning of saw and chain and guide bar maintenance

can reduce chances of kickback. Inspect and maintain

saw after each use. This will increase the service life of

your saw. Note: Even with proper sharpening, risk of

kickback can increase with each sharpening.

MAINTENANCE AND STORAGE OF

CHAIN SAW

1. Unplug chain saw from power source

• when not in use

• before moving from one place to another

• before servicing

• before changing accessories or attachments,

such as saw chain and guard

2. Inspect chain saw before and after each use.

Check saw closely if guard or other part has

been damaged. Check for any damage that may

affect operator safety or operation of saw. Check

for alignment or binding of moving parts. Check

for broken or damaged parts. Do not use chain

saw if damage affects safety or operation. Have

damage repaired by authorized service center.

3. Maintain chain saw with care.

• Never expose saw to rain.

• Keep chain sharp, clean, and lubricated for

better and safer performance.

• Follow steps outlined in this manual to sharpen

chain.

• Keep handles dry, clean, and free of oil and

grease.

• Keep all screws and nuts tight.

• Inspect power cord often. If damaged, have

repaired by authorized service center.

• Never carry chain saw by power cord.

• Never yank power cord to unplug it.

• Keep power cord from heat, oil, and sharp

edges.

• Inspect extension cords often and replace if

damaged.

4. When servicing, use only identical replacement

parts.

5. When not in use, always store chain saw

• in a high or locked place, out of children’s reach

• in a dry place

• in a carrying case or with scabbard over guide bar

Save these instructions. It is your guide to safe and

proper operation of this chain saw.

6

113005

www.desatech.com

Bucking Process of cutting a felled tree or log into

lengths.

Chock Block or wedge used to secure wood from

moving.

Felling Process of cutting down a tree.

Felling Cut Final cut when felling a tree. Make this

cut on opposite side of tree from notching cut.

Front Handle Located at front of saw body.

Front Hand Guard Shield between front handle and

guide bar. Protects left hand while using saw.

Guide Bar Metal bar that extends from saw body.

The guide bar supports and guides chain.

Guide Bar Nose Tip or end of guide bar.

Guide Bar Retainer Bolt-like fastener that holds

guide bar in place during assembly and operation

of chain saw.

Kickback Quick backward and upward motion of

guide bar. Kickback may occur when tip of guide bar

touches an object while chain is moving. The guide

bar will kick up and back towards operator.

Limbing Process of cutting limb(s) from a felled tree.

Low-Kickback Chain Chain that reduces chance of

kickback as required by ANSI B175.1.

Normal Cutting Position Stance used while making

bucking and felling cuts.

Notching Cut Notch cut in tree that directs fall of tree.

PRODUCT IDENTIFICATION

Figure 2 - Chain Saw Model M12510US,

M15012US, M15014US, M15014AS, M30016US,

M30016AS

Chain Tensioning Screw

Rear Handle

Power Cord

Guide Bar

Saw Chain

Front Handle

Oil Cap

Trigger

Switch Lockout

Cord Hitch

Guide Bar Nose

UNPACKING

1. Remove all items from carton.

2. Check all items for any shipping damage. If you

ﬁnd any damage or if any parts are missing, call

Technical Services at 1-800-858-8501 for prompt

service.

Oiler Control System for oiling guide bar and chain.

Power Head Chain saw without chain and guide bar.

Also known as saw body.

Pushback (Kickback, Pinch) Rapid pushback of chain

saw. Pushback may occur if chain along top of guide

bar is pinched, caught, or contacts a foreign object.

Rear Handle Handle located at rear of saw body.

Reduced Kickback Guide Bar Guide bar that re-

duces chance of kickback.

Replacement Chain Chain that complies with ANSI

B175.1 when used with a speciﬁc saw. It may not meet

ANSI requirements when used with other saws.

Saw Chain (Chain) Loop of chain having cutting

teeth for cutting wood. The motor drives chain. The

guide bar supports chain.

Spiked Bumper (Spike) Pointed teeth at front of

saw body beside guide bar. Keep spiked bumper in

contact with wood when felling or bucking. It helps

maintain position of saw while cutting.

Sprocket Toothed wheel that drives chain.

Switch Device that completes or interrupts electrical

circuit to motor of saw.

Switch Linkage This device connects switch to trig-

ger. It moves switch when you squeeze trigger.

Switch Lockout Device that reduces accidental

starting of saw.

Hand Guard

Figure 3 - Chain Saw Model M30016AW,

M35016UW, M35016AW

Chain Tensioning Screw

Rear Handle

Power Cord

Guide Bar

Saw Chain

Front Handle

Oil Cap

Trigger

Switch Lockout

Cord Hitch

Guide Bar Nose

Hand Guard

CHAIN SAW NAMES AND TERMS

7

113005

www.desatech.com

ENGLISH

ASSEMBLY

Note: Some models are pre-assembled. Assembly is

not needed on these models.

See

Saw Chain Tension Adjustment, pages 8 and 9.

1. Lay chain out ﬂat.

2. Loosen and remove guide bar nut and sprocket

cover.

3. Rotate guide bar retainer so that it is positioned

parallel to guide bar slot (see Figure 4).

4. Install guide bar onto saw body. Assemble center

slot of guide bar onto guide bar bolt and guide bar

retainer.

Note: Make sure the head of the guide

bar retainer slides through the guide bar slot as

shown in Figure 4.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

IMPORTANT: Do not clamp chain saw in

vise during assembly.

Continued

CHAIN SAW NAMES AND

TERMS

Continued

5. Rotate guide bar retainer 90 degrees as shown in

Figure 5.

6. Place chain around drive sprocket, along top groove

of guide bar, and around guide bar nose.

Note:

Make sure cutting edges of chain are facing in

right direction. Position chain so cutting edges on

top of guide bar face guide bar nose (see Figure

6 and indicator on side cover of saw).

CAUTION: Do not place chain on saw

backwards. If chain is backwards, saw

will vibrate badly and will not cut.

7. Insert tab of sprocket cover into slot on unibody

and rotate sprocket cover onto guide bar bolt

until sprocket cover rests against guide bar (see

Figure 7, page 8).

8. Place guide bar nut, removed in step 2, on guide

bar bolt.

IMPORTANT: Tighten guide bar nut ﬁnger tight

only.

Trigger Device that turns saw on and off. Squeezing

trigger turns saw on. Releasing trigger turns saw off.

Trimming (Pruning) Process of cutting limb(s) from

a living tree.

Undercut An upward cut from underside of log or

limb. This is done while in normal cutting position

and cutting with top of guide bar.

Unibody Main body of chain saw.

Figure 4 - Unlocking Guide Bar Retainer

U

N

L

O

C

K

E

D

Guide Bar Retainer

Positioned Parallel

to Guide Bar Slot

Figure 5 - Locking Guide Bar Retainer

L

O

C

K

E

D

Guide Bar Retainer

Rotated 90 Degrees

to Guide Bar Slot

Guide Bar

Drive

Sprocket

Drive

Sprocket

Figure 6 - Saw Chain Direction

Cutting Edge

Towards Guide Bar

Nose

8

113005

www.desatech.com

SAW CHAIN TENSION

ADJUSTMENT

WARNING: Unplug chain saw from

power source before adjusting saw chain

tension.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

WARNING: Maintain proper chain ten-

sion always. A loose chain will increase

the risk of kickback. A loose chain may

jump out of guide bar groove. This may

injure operator and damage chain. A

loose chain will cause chain, guide bar,

and sprocket to wear rapidly.

Figure 8 - Chain Tensioning Screw and

Adjustment Block Location

ASSEMBLY

Continued

IMPORTANT!

Failure to follow these instructions when tensioning

saw chain will damage saw and void the warranty. For

additional information call 1-800-858-8501.

New saw chains will stretch. Check chain tension

frequently when ﬁrst used and tighten when chain

becomes loose around guide bar.

L

O

S

E

N

❶

Loosen nut...

If chain becomes loose around guide

bar, allow chain to cool then...

❷

Chain Tensioning

Screw

Adjustment Block

Step

1

Step

2

Figure 7 - Installing Sprocket Cover

Guide Bar Bolt

Bushing

Guide Bar Nut

Sprocket Cover Tab

Slot

Adjusting Hole

9. Turning chain tensioning screw, adjust posi-

tion of adjustment block until it is aligned and

inserted into the round adjusting hole on guide

bar (see Figures 7 and 8). Turning screw coun

-

terclockwise will move adjustment block to rear

of guide bar. Turning screw clockwise will move

adjustment block to front of guide bar.

10. If needed, readjust guide bar nut to ﬁnger tight only.

11. Adjust saw chain tension. Follow steps under

Saw Chain Tension Adjustment,

pages 8 and 9.

9

113005

www.desatech.com

ENGLISH

OPERATING CHAIN SAW

WARNING: Read and understand this

owner’s manual before operating this saw.

Make certain you read and understand all

Important Safety Information, pages 3

through 5. Improper use of this chain saw

can cause severe injury or death from

ﬁre, electrical shock, or body contact with

moving chain, or falling wood.

Continued

T

I

G

H

T

E

N

Approx.

1/8"

T

I

G

H

T

E

N

Turn chain tensioning screw

clockwise to tension saw chain...

❸

SAW CHAIN TENSION

ADJUSTMENT

Continued

Pull chain to check tension. Guide

links should not come out of guide

bar groove...

❹

Make sure chain moves freely around

guide bar then tighten nut.

❺

FILLING OIL TANK

1. Remove oil cap.

2. Fill oil tank with SAE #30 motor oil.

Note: For

temperatures below 30°F, use SAE #10 oil. For

temperatures above 75°F, use SAE #40 oil.

3. Replace oil cap at once. Tighten oil cap ﬁrmly for

good seal. This will avoid oil seepage from tank.

4. Wipe off excess oil.

Note:

It is normal for oil to seep when saw is not in use.

Empty oil tank after each use to prevent seepage.

OILING CHAIN

Manual Oil System

Always check oil level before using saw. Do not

attempt to operate the oil system while saw is in

operation. To oil chain, press squeeze bulb. Oil will

feed onto the guide bar and chain. Press squeeze

bulb at least once before each cut. Check oil level

often by looking at oil level through side of oil bottle

(see Figure 9).

Guide Bar

Figure 9 - Oil Squeeze Bulb and Oil Bottle

Location

Oil Bottle

Oil Squeeze Bulb

10

113005

www.desatech.com

Figure 11 - Looping Extension Cord over Cord

Hitch

Power Cord

Extension Cord

Cord Hitch

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 16 AWG

150 feet 14 AWG

Models M12510US, M15012US, M15014US,

M15014AS

Keep cord away from cutting area. Make sure cord

does not catch on branches or logs during cutting.

Inspect cords often. Replace damaged cords.

This chain saw is designed with an extension cord hitch

that prevents the extension cord from being pulled loose

during use. To use, form a loop with the end of the

extension cord, insert loop into slot in rear of handle,

and place loop over cord hitch (see Figure 11). Gently

pull loop against cord hitch until slack is removed.

Plug extension cord into chain saw cord.

EXTENSION CORDS

Use proper extension cords with this saw. Use only

extension cords marked for outdoor use. The cord must

be marked with sufﬁx W or W-A following the cord

type designation. Example: SJTW-A or SJTW.

Use proper sized cord with this saw. Cord must be heavy

enough to carry current needed. An undersized cord will

cause voltage drop at saw. Saw will lose power and over

-

heat. Follow cord size requirements listed below.

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 14 AWG

150 feet 12 AWG

Models M30016US, M30016AS, M30016AW,

M35016UW, M35016AW

OPERATING CHAIN SAW

Continued

CLEARING SPROCKET COVER OF

DEBRIS

While operating the chain saw, wood chips, small

twigs, and other debris can occasionally build up

inside the sprocket cover. To properly maintain the

saw and keep it in good working order, periodic

removal of this debris may be required. To properly

clear debris from the sprocket cover:

1. Unplug chain saw.

2. Loosen and remove guide bar nut (see Figure

10).

3. Turn chain tensioning screw counterclockwise

to loosen chain until sprocket cover is easily

removed.

4. After sprocket cover is removed, clear all chips,

twigs, and debris.

WARNING: Use caution when clear-

ing debris that is around chain. Cutting

edges on chain are sharp. Use protec

-

tive gloves when working around or

handling chain.

5. Once debris has been removed, follow steps 7

through 11 on pages 7 and 8 in the

Assembly

section to re-assemble the sprocket cover to the

chain saw.

Figure 10 - Removing and Clearing Sprocket

Cover of Debris

Wood Chips, Twigs,

and Debris

Sprocket Cover

Guide Bar Nut

11

113005

www.desatech.com

ENGLISH

Figure 12 - Lockout Button and Trigger Location

Switch Lockout Button

Trigger

CUTTING WITH THE CHAIN SAW

1. Connect saw to extension cord. Connect exten-

sion cord to power supply.

2. Make sure section of log to be cut is not laying

on ground. This will keep chain from touching

ground as it cuts through log. Touching ground

with moving chain will dull chain.

3. Use both hands to grip saw. Always use left hand

to grip front handle and right hand to grip rear

handle. Use ﬁrm grip. Thumbs and ﬁngers must

wrap around saw handles (see Figure 12).

4. Make sure your footing is ﬁrm. Keep feet apart.

Divide your weight evenly on both feet.

5. When ready to make a cut, push the lockout

button completely forward with the right thumb

and squeeze the trigger (see Figure 12). This will

turn saw on. Releasing trigger will turn saw off.

Make sure saw is running at full speed before

starting a cut.

6. When starting a cut, place moving chain against

wood. Hold saw ﬁrmly in place to avoid possible

bouncing or skating (sideways movement) of saw.

7. Guide saw using light pressure. Do not force

saw. The motor will overload and can burn out.

It will do the job better and safer at the rate for

which it was intended.

8. Remove saw from a cut with saw running at full

speed. Stop saw by releasing trigger. Make sure

chain has stopped before setting saw down.

9. Practice until you can maintain a steady, even

cutting rate.

OPERATING CHAIN SAW

Continued

Felling is the process of cutting down a tree. Make

sure your footing is ﬁrm. Keep feet apart. Divide

your weight evenly on both feet. Follow directions

below to fell a tree.

Before Felling a Tree

1. Before felling, inspect tree. Make sure there are

no dead limbs or branches that may fall on you.

Study natural lean of tree, location of larger

branches, and wind direction. This will help you

judge which way tree will fall.

2. Clear work area around tree.

3. Plan and clear a retreat path before felling. Make

retreat path opposite to planned direction of fall

of tree and at 45° angle (see Figure 13).

WARNING:

• Avoid kickback. Kickback can result in se

-

vere injury or death. See Kickback, pages

4 and 5, to avoid risk of kickback.

• Do not fell a tree without ample skill or

expert help.

• Keep children, animals, and bystanders

away from area when felling a tree.

• If two or more persons perform buck

-

ing and felling operations at the same

time, provide ample distance between

operations. Provide distance of at least

twice the height of tree being felled.

WARNING: When felling a tree, be

aware of your surroundings. Do not

endanger any person, strike utility lines,

or cause property damage. If tree strikes

utility lines, contact utility company at

once.

FELLING A TREE (Cutting Down a

Tree)

Figure 13 - Retreat Path From Tree

Direction of Fall

Retreat Path

45°

Tree

Continued

12

113005

www.desatech.com

WARNING: When cutting limb that

is under tension, use extreme caution.

Be alert for wood springing back. When

wood tension is released, limb could

spring back and strike operator causing

severe injury or death.

Limbing is removing branches from a fallen tree.

Make sure your footing is ﬁrm. Keep feet apart.

Divide your weight evenly on both feet. Do not

remove larger limbs under tree that support log off

ground. Remove each limb with one cut (see Figure

15). Clear cut limbs from work area often. This will

help maintain a safe work area.

Make sure you start your cut where limb will not

pinch saw during cutting. To avoid pinching, start cut

on freely hanging limbs from above limb. Start cut on

limbs under tension from under limb. If pinch occurs,

turn saw off, lift limb, and remove saw.

LIMBING A TREE

WARNING: Avoid kickback. Kickback

can result in severe injury or death. See

Kickback, pages 4 and 5, to avoid risk

of kickback.

WARNING: Be alert for falling over-

head limbs. Watch your footing while

exiting area.

3. As felling cut nears hinge, tree should begin to fall.

Note: If needed, drive wedges into felling cut to

control direction of fall. If tree settles back and

pinches chain, drive wedges into felling cut to re

-

move saw. Only use wedges made of wood, plastic,

or aluminum. Never use wedge made of steel. This

could cause kickback and damage to chain.

4. When tree begins to fall, quickly

• remove saw from felling cut

• release trigger to turn saw off

• put saw down

• exit area using retreat path

Figure 15 - Limbing A Tree

OPERATING CHAIN SAW

Continued

Figure 14 - Felling A Tree

Direction

of Fall

Hinge

2"

(5 cm)

2"(5 cm)

2nd Cut -

Upper Notch Cut

1st Cut -

Lower Notch Cut

3rd Cut -

Felling Cut

4. Remove dirt, stones, loose bark, nails, staples, and

wire from tree where you will make felling cuts.

5. Stay on uphill side when felling tree. Tree could

roll or slide downhill after falling.

Felling Procedure

A) Felling Notch

A properly placed felling notch will determine direc-

tion tree will fall. Place felling notch on side of tree in

direction you want tree to fall (see Figure 14). Follow

directions below to create a felling notch.

1. Make lower notch cut as close to ground as pos

-

sible. Hold saw so guide bar is horizontal. Cut

1/3 the diameter of tree trunk (see Figure 14).

Note: Always make this horizontal lower notch

cut ﬁrst. If you make this cut second, tree can

pinch chain or guide bar.

2. Start upper notch cut the same distance above

ﬁrst cut as ﬁrst cut is deep.

Example: If lower notch cut is eight inches deep,

start upper notch cut eight inches above it. Cut

downward at 45° angle. The upper notch cut should

meet end of lower notch cut (see Figure 14).

3.

Remove tree trunk wedge created by notching cuts.

B) Felling Cut

1. Make felling cut two inches higher than lower

notch cut and on opposite side of tree (see Figure

14). Keep felling cut parallel to lower notch cut.

2. Cut towards notch.

WARNING: Do not cut all the way

through tree. Leave about two inches

of tree diameter uncut directly behind

felling notch (see Figure 14). This uncut

portion acts as a hinge. The hinge helps

keep tree from twisting and falling in

wrong direction.

13

113005

www.desatech.com

ENGLISH

BUCKING A LOG

WARNING: Avoid kickback. Kickback

can result in severe injury or death. See

Kickback, pages 4 and 5, to avoid risk

of kickback.

WARNING:

• If on slope, make sure log will not roll

down hill. Secure log by using wooden

stakes. Drive wooden stakes into

ground on downhill side of log. Stand

on uphill side of log while cutting. Log

may roll after cutting.

• Never try cutting through two logs at

same time. This could increase the risk

of kickback.

• While cutting log, never hold log with

your hand, leg, or foot.

• While cutting log, never allow another

person to hold log.

• Turn off and unplug saw before moving

from one place to another.

Bucking a log is cutting a log into sections. Make

sure your footing is ﬁrm. Keep feet apart. Divide your

weight evenly on both feet. When possible, raise log

or section off ground. Do this by using limbs, logs,

chocks, etc.

When cutting through log, maintain control by reduc

-

ing cutting pressure near end of cut. Do not relax your

grip on chain saw handles. Do not let moving chain

touch ground. Ground will dull moving chain. After

cutting through log, release trigger to turn saw off

before moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 16).

OPERATING CHAIN SAW

Continued

Figure 16 - Bucking Log With Entire Length

On Ground

TRIMMING A TREE (Pruning)

WARNING: Avoid kickback. Kickback

can result in severe injury or death. See

Kickback, pages 4 and 5, to avoid risk

of kickback.

Log Supported On One End

1. Make ﬁrst cut on underside of log (see Figure

17). Use top of guide bar to make this cut. Cut

1/3 through diameter of log. This cut will keep

section from splintering when cut.

2. Make second cut directly above ﬁrst cut. Cut

down to meet ﬁrst cut. This cut will keep log

from pinching guide bar and chain.

Log Supported On Both Ends

1. Make ﬁrst cut from above log (see Figure 18).

Cut 1/3 through diameter of log. This cut will

keep section from splintering when cut.

2. Make second cut on underside of log, directly

under ﬁrst cut. Use top of guide bar to make this

cut. Cut up to meet ﬁrst cut. This will keep log

from pinching guide bar and chain.

Figure 17 - Bucking Log When Log Is Supported

On One End

Figure 18 - Bucking Log When Log Is Supported

On Both Ends

1st Cut

2nd Cut

1st Cut

2nd Cut

Continued

14

113005

www.desatech.com

OPERATING CHAIN SAW

Continued

WARNING: Do not operate chain

saw while

• in a tree

• on a ladder or any other unstable sur

-

face

• in any awkward position

You may lose control of saw causing

severe injury.

WARNING: Do not cut limbs higher

than your shoulders.

CAUTION: Seek professional help if

facing conditions beyond your ability.

Trimming a tree is the process of cutting limbs from

a living tree. Make sure your footing is ﬁrm. Keep

feet apart. Divide your weight evenly on both feet.

Follow directions below to trim a tree.

Figure 19 - Cutting A Limb

2" to 4"

(5 a 10 cm)

2nd Cut - Pruning Cut

(to avoid pinching)

1st Cut - Pruning Undercut

(to avoid splintering)

3rd Cut - Stub Undercut

(to avoid splintering)

6"

(15 cm)

4th Cut - Final Stub Cut

1. Make ﬁrst cut six inches from tree trunk on

underside of limb. Use top of guide bar to make

this cut. Cut 1/3 through diameter of limb (see

Figure 19).

2. Move two to four inches farther out on limb.

Make second cut from above limb. Continue cut

until you cut limb off.

3. Make third cut as close to tree trunk as possible

on underside of limb stub. Use top of guide bar to

make this cut. Cut 1/3 through diameter of stub.

4. Make fourth cut directly above third cut. Cut down

to meet third cut. This will remove limb stub.

15

113005

www.desatech.com

ENGLISH

CARE OF GUIDE BAR

Uneven bar wear causes most guide bar problems.

Incorrect sharpening of chain cutter and depth gauge

settings often cause this. When bar wears unevenly,

it widens guide bar groove (see Figure 20). This

causes chain clatter and rivet popping. Saw will not

cut straight. Replace guide bar if this occurs.

Inspect guide bar before sharpening chain. A worn or

damaged guide bar is unsafe. A worn or damaged guide

bar will damage chain. It will also make cutting harder.

CLEANING SAW BODY

CLEANING AND

MAINTENANCE

NOTICE: Below are instructions for ser-

vicing your chain saw. Any servicing not

mentioned below should be done by an

authorized service center.

WARNING: Unplug chain saw from

power source before servicing. Severe injury

or death could occur from electrical shock

or body contact with moving chain.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

WARNING: When cleaning saw body,

• do not submerge saw in any liquids

• do not use products that contain am

-

monia, chlorine, or abrasives

• do not use chlorinated cleaning sol

-

vents, carbon tetrachloride, kerosene,

or gasoline

Keep saw body clean. Use a soft cloth dampened with a

mild soap and water mixture. Wipe saw body to clean.

Normal Guide Bar Maintenance

1. Remove guide bar from chain saw.

2. Remove sawdust from guide bar groove periodi

-

cally. Use putty knife or wire (see Figure 21).

3. Clean oil slots after each day of use.

4. Remove burrs from sides of guide bar. Use ﬂat

ﬁle to make side edges square.

Replace guide bar when

• bar is bent or cracked

• inside groove of bar is badly worn

Note: When replacing guide bar, see Replacement

Parts and Accessories, page 17, for proper bar.

WARNING: Unplug chain saw from

power source before servicing. Severe injury

or death could occur from electrical shock

or body contact with moving chain.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

SHARPENING SAW CHAIN

Keep chain sharp. Your saw will cut faster and more

safely. A dull chain will cause undue sprocket, guide

bar, chain, and motor wear. If you must force chain

into wood and cutting creates only sawdust with few

large chips, chain is dull.

Guide Bar With

Uneven Wear

Figure 20 - Guide Bar Cross Section Showing

Uneven Bar Wear

Guide Bar

Normal Guide

Bar

Guide Bar Groove

Figure 21 - Guide Bar Maintenance

Flat File

Burr

Oil Slot

Cleaning Groove With Putty Knife

Guide Bar

Continued

16

113005

www.desatech.com

CLEANING AND

MAINTENANCE

Continued

4. Hold ﬁle guide level. Make sure 30° mark on

ﬁle guide is parallel to center of guide bar (see

Figure 22). This will insure that you ﬁle cutters

at 30° angle.

5. File from inside towards outside of cutter until

sharp. Only ﬁle in this one direction (see Figure

22). Note: Two or three strokes with ﬁle should

sharpen cutter.

6. After each cutter is sharpened, move chain for

-

ward to sharpen next cutter. File all cutters on

one side of chain.

7. Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters

are sharpened. After every second or third sharpen

-

ing, reset cutter depth gauges.

1. Place depth gauge tool (.025") ﬁrmly across top

of two cutters. Make sure depth gauge enters slot

in depth gauge tool (see Figure 24).

2. Use medium ﬂat ﬁle. File depth gauge level with

depth gauge tool.

3. Remove depth gauge tool. With ﬂat ﬁle, round

off front corner of cutter depth gauge (see Figure

25).

After several hand ﬁlings, have authorized service

center or sharpening service machine sharpen chain.

This will insure even ﬁling.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or

when chain breaks. Only use replacement chain noted in

this manual. Always include new drive sprocket when

replacing chain. This will maintain proper driving of

chain. Note: For proper chain and drive sprocket, see

Replacement Parts and Accessories

, page 17.

Figure 24 - Depth Gauge Tool On Chain

Flat File

Depth Gauge Slot

Depth Gauge Tool

Depth

Gauge

Figure 25 - Round Off Front Corner Of Depth

Gauge

Front Corner

.025"

.635 mm

FILE

HOLDER

Items Needed to Sharpen Chain

Purchase these items from your local dealer, hard-

ware store, or chain saw supplies outlet.

• 5/32" round ﬁle

• Depth gauge tool

• File guide

• Vise

• Medium sized ﬂat ﬁle

Sharpening Cutters

Use ﬁle guide for 30° ﬁling.

1. Adjust chain for proper tension (see Saw Chain

Tension Adjustment,

pages 8 and 9).

2. Clamp guide bar in vise to hold saw steady. Note:

Do not clamp chain.

3. Press 5/32" round ﬁle (attached to ﬁle guide)

into groove between top plate and depth gauge

on chain. File guide should rest on both top plate

and depth gauge (see Figure 22).

Note: File at

midpoint of guide bar.

Figure 22 - File and File Guide Placement On

Chain

Note: This illustration shows ﬁle guide placement and ﬁling

direction for sharpening cutters on left side of chain.

File Guide

Filing Direction

5/32" Round

File

Figure 23 - Chain Part Locations

30° Guide Mark

Groove

Depth Gauge (left

side of chain)

Top Plate (left

side of chain)

Right Side of Chain

Groove

Depth Gauge (right

side of chain)

Top Plate

(right side of chain)

17

113005

www.desatech.com

ENGLISH

STORAGE

If storing saw for more than 30 days, follow steps below.

1. Drain oil tank after each use.

2. Remove and clean guide bar and chain. Clean

guide bar and chain by soaking in petroleum

based solvent or mild soap and water mixture.

3. Dry guide bar and chain.

4. Place chain in container ﬁlled with oil. This will

prevent rust.

5. Wipe a thin coating of oil over surface of guide bar.

6. Wipe off outside of saw body. Do this with soft cloth

dampened with a mild soap and water mixture.

7. Store chain saw

•

in a high or locked place, out of children’s reach

• in a dry place

• in a carrying case or with scabbard over guide bar

TECHNICAL SERVICE

You may have further questions about assembling,

operating, or maintaining this product. If so, you

can visit our Technical Service web site at www.

desatech.com or contact our Technical Service

Department at 1-800-858-8501 (English Only). You

may also write to:

DESA Specialty Products™

ATTN: Technical Service Specialty Products

P.O. Box 90004

Bowling Green, KY 42102-9004

When contacting DESA Specialty Products™, have

ready

• Your Name

• Your Address

• Your Phone Number

• Model Number of Product

• Date of Purchase (Include copy of receipt for writ

-

ten requests).

WARNING: Use only replacement parts

and accessories described in this manual.

Use of other parts or accessories could

damage saw or injure operator.

REPLACEMENT PARTS

AND ACCESSORIES

For original replacement parts and accessories, con-

tact your nearest Authorized Dealer or Authorized

Service Center for this product. If they can not sup

-

ply the part or accessory, contact your nearest Parts

Central listed on page 65. Each Authorized Dealer,

Authorized Service Center, and Parts Central is

independently owned and operated.

See pages 62 through 64 for an Illustrated Parts List.

If you need additional referral information, contact our

Technical Service Department (see Technical Service).

In Canada call 1-800-561-3372 for parts information.

REPAIR SERVICE

Note: Only use original replacement parts. This will

protect your warranty coverage for parts replaced

under warranty.

Each Authorized Service Center is independently

owned and operated.

WARRANTY SERVICE

If product requires warranty service, return it to nearest

Authorized Service Center. You must show proof of

purchase. If faulty materials or workmanship caused

damage, we will repair or replace product without

charge. Note: Normal wear, misuse, abuse, neglect, or

accidental damage is not covered under warranty.

NON-WARRANTY SERVICE

If product requires service, return it to nearest Autho-

rized Service Center. Repairs will be billed to you at

regular repair list prices.

For additional Service Center or warranty informa

-

tion, call 1-800-858-8501 or visit our Technical

Service web site at www.desatech.com.

18

113005

www.desatech.com

TROUBLESHOOTING

WARNING: Unplug chain saw from

power source before servicing. Severe injury

or death could occur from electrical shock

or body contact with moving chain.

Note: For additional help, visit DESA Power

Tools’™ technical service web site at www.

desatech.com.

OBSERVED FAULT

Saw runs, but does not cut

Saw does not cut unless heavily

forced. Cutting produces only saw-

dust with few large chips

Saw runs slow. Saw stalls easily

Motor of saw does not run when you

squeeze trigger

Motor of saw runs, but chain does

not move

Chain does not get oil

Chain comes off guide bar

Saw smokes

Saw leaks oil

POSSIBLE CAUSE

Chain assembled backwards on

guide bar

Chain is dull

Low power supply voltage

1. Switch lockout not pushed for-

ward in to release trigger

2. Extension cord connections loose

3. Open line fuse or circuit breaker

4. Worn out motor brushes

5. Open wiring circuit on saw

Gear train failure

1. Clogged oil slot in guide bar

2. Oil is too thick

1. Chain is loose

2. Guide bar and chain not as-

sembled correctly

Saw damaged. Do not use saw

Oil cap is not secure

REMEDY

See Assembly, pages 7 and 8

See Sharpening Saw Chain, pages

15 and 16

Extension cord wire size too small.

See Extension Cords, page 10

1. Push switch lockout forward

before squeezing trigger

2. Check cord connections

3. Check line fuse or circuit breaker

4. See authorized service center

5. See authorized service center

See authorized service center

1. Remove guide bar and clean oil

slot

2. Use correct weight of oil. See

Filling Oil Tank, page 9

1. Tighten chain. See Saw Chain Ten-

sion Adjustment, pages 8 and 9

2. See Assembly, pages 7 and 8

See authorized service center

Tighten oil cap. Note: Empty oil

tank when not in use.

La page charge ...

Remington Chainsaw Electric Chain Saw Manuel utilisateur

Remington Chainsaw Electric Chain Saw Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents