Broan XB50L1 Mode d'emploi

XB50L1

n

XB80L1

n

XB110L1

X1 | Single-Speed Ventilation

Fan with Dimmable Light

INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS

Installer: leave this guide with homeowner.

Register your product online at www.broan.com/register.

Easy installation in both

new construction and retrofit

Table of Contents

Warnings and Cautions 2

Typical Installation 2

New Construction Installation 3

Retrofit Installation 7

Operation 12

Cleaning and Maintenance 12

Troubleshooting 12

Service Parts 13

Warranty 13

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 2

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE), and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Use only ON/OFF switch, mechanical timer or relay-switched

control.

8. Acceptable for use over a tub or shower when connected to

a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

9. This unit must be grounded.

Typical Installation

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. This product is designed for installation in ceilings up to a

12/12 pitch (45 degree angle). Duct connector must point up.

DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Please read specification label on product for further

information and requirements.

45° 45°

• Installation is the same for:

• Fits in 2" x 8" ceiling construction.

• Infinitely adjust the fan position

between joists from 14" to 24"

on center.

• Do not install this fan in a ceiling

thermally insulated to a value

greater than R40.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

ROOF CAP*

(with built-in

damper)

FAN

HOUSING

POWER

CABLE*

ROUND

DUCT*

ROUND

ELBOWS*

Seal gaps

around

Housing.

Seal duct

joints with

tape.

OR

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

NOT FOR USE IN A COOKING AREA

Do not install above or inside this area

Floor

Cooking

Equipment

Joists I-Joists Trusses

The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and en-

ergy use of the fan. Use the shortest, straighest duct routing possible for best performance, and avoid

installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce en-

ergy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow.

6-inch round rigid metal duct is recommended for best performance.

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 3

1

2

3

4

Parts Bag holds

Knockout Plate

and six (6)

screws

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 6.

New Construction Installation

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

Materials needed

• 6" round metal ducting recommended for best performance.

Use of other ducting is acceptable but may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code requirements

1

Remove Packaging

2

Install

Mounting

Frame

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 4

3

1

4

2

1

2

3

New Construction Installation

3

Snap-in and

Secure Housing

4

Attach Duct Connector and Ducting

Position Housing

between joists and

crimp channel on both

sides of Mounting Frame

to lock Housing in place.

Do not crimp Housing.

Screws from Parts Bag

Top and bottom flanges

go outside Housing

Insert tab into slot

inside Housing

Screw from

Parts Bag

6" to 4" Reducer provided in select models

Tape

6" Ducting

4" Ducting

snap!

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 5

3

4

1

2

New Construction Installation

5

Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation location.

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

Screw from

Parts Bag

Attach cable clamps to

Knockout Plate. Knockout

Plate mounts to outside of

Housing and may be

oriented as desired.

Connect wires

LINE

IN

GRD

WHT

BLK

GRD

WHT

BLK

RED BLU

RED

BLK

LIGHT

SWITCH

FAN

SWITCH

FAN

LIGHT

UNITSWITCH BOX

LINE

IN

GRD

WHT

BLK

GRD

WHT

BLK

RED BLU

RED

BLK

DIMMER

SWITCH

FAN

SWITCH

FAN

LIGHT

UNITSWITCH BOX

LIGHT WITH ON/OFF SWITCH

LIGHT WITH DIMMER SWITCH

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 6

1

2

3

1

2

3

1

New Construction Installation

6

Insert Mask and

Finish Ceiling

7

Install Grille

See Page 12 for Operations, Cleaning and Maintenance, and Troubleshooting.

Mask protects unit

during construction.

Remove before

installing Grille.

• Install ceiling material.

• Cut out around Housing.

CAUTION

If the blower was unplugged, power must be

disconnected (see page 2, WARNING item 2)

before inserting motor plugs into control assembly.

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 7

12" (30.5 cm)

1

2

Retrofit Installation

Parts Bag holds

Knockout Plate

and six (6)

screws

Existing ductwork and

wiring left in place

11" (27.9 cm)

parallel with joists

Examine the existing wiring to make sure it is not damaged. If any damage is found,

DO NOT CONTINUE INSTALLATION of this product. Contact a qualified person(s) for repair.

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 12.

1

Remove Packaging

2

Switch Off Power

4

Examine Wiring

3

Enlarge Ceiling Opening and Remove Existing Fan

• Ruler

• Pencil

• Drywall saw

• Claw hammer or pry bar

• Utility knife

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the

addition of a short length of flexible duct

• Electrical wiring and supplies per

local code requirements

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

WARNING

Before removing existing fan, switch power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 8

2

1

2

3

4

5

1

2

3

Retrofit Installation

5

Remove Blower Assembly

6

Remove Wiring Panel

7

Insert

Mounting

Frame

Both sides

Set aside

Blower

Assembly

Set aside

Wiring Panel

Set aside

screw

Bend up

four tabs

Remove screws from

Mounting Frame

and set aside

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 9

1

2

1

3

4

Retrofit Installation

Screw from

Parts Bag

Screws set

aside

in Step 7

Pull existing wiring into

Housing as it is inserted

into Mounting Frame

Pull existing

ductwork

into Housing

Insert tab into

slot inside

Housing

10

Attach Ducting and Duct Connector

8

Secure

Mounting

Frame

9

Snap-in Housing

snap!

6" to 4" Reducer provided in select models

Tape

6" Ducting

4" Ducting

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 10

2

1

4

5

6

3

Retrofit Installation

11

Install Knockout Plate, Connect Wires and Reinstall Wiring Panel

Screw from

Parts Bag

Attach cable

clamps to

Knockout Plate.

Knockout Plate

mounts to inside of

Housing and may

be oriented

as desired.

Connect wires

Screw set

aside in

Step 6

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

LINE

IN

GRD

WHT

BLK

GRD

WHT

BLK

RED BLU

RED

BLK

LIGHT

SWITCH

FAN

SWITCH

FAN

LIGHT

UNITSWITCH BOX

LINE

IN

GRD

WHT

BLK

GRD

WHT

BLK

RED BLU

RED

BLK

DIMMER

SWITCH

FAN

SWITCH

FAN

LIGHT

UNITSWITCH BOX

LIGHT WITH ON/OFF SWITCH

LIGHT WITH DIMMER SWITCH

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 11

1

2 3

1

2

3

1

Retrofit Installation

12

Reinsert and Secure Blower Assembly

13

Install Grille

If ceiling repairs are needed, place Mask in Housing

after Blower Assembly is secured. See New Construction

Installation Step 6. Remove Mask before installing Grille.

Screws from Parts Bag

CAUTION

Power must be disconnected (see page 2, WARNING item 2) before inserting motor plugs into control assembly.

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

1

2 3

1

2

3

1

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 12

WARNING Before servicing or cleaning unit,

switch power off at service panel and lock the service

disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

Operation

To Operate Fan

Use an ON/OFF switch to operate this ventilator.

It is normal for this ventilation fan to take approximately 5

seconds to start running after it is turned on.

To Operate Lights

The fan and light can be operated independently, using

separate switches. The light may be operated with a

dimmer switch. See wiring diagrams.

Cleaning and Maintenance

To Clean

For quiet and efficient operation, long life and attractive

appearance, remove Grille and vacuum interior of unit

with a dusting brush attachment.

The Motor is permanently lubricated and never needs

oiling. If the motor bearings are making excessive or

unusual noises, replace the Control Assembly and Motor.

CAUTION

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

DO NOT remove motor plug to stop spinning motor.

Power must be disconnected (see WARNING above) before

motor plug is removed or inserted into control assembly.

Troubleshooting

Symptom: The fan does not run.

• Check for an open fuse or circuit breaker in the building’s

service panel.

• Check that the two (2) plug-in connections for the Motor

and the Control are seated firmly in place.

• Check that the Blower Wheel spins freely.

Symptom: The fan runs erratically.

• Check that the Blower Wheel is firmly attached to the

Motor shaft and both spin freely.

Symptom: The fan seems noisy.

• Check that the back draft damper in the fan’s Duct

Connector pivots freely. Screws used to attach the duct to

the Duct Connector may be preventing the damper from

opening.

• Check that the back draft damper in the wall or roof cap

pivots freely. These dampers are sometimes mistakenly

painted shut or obstructed by bird and insect debris..

XB50L1

n

XB80L1

n

XB110L1 Installation Guide

Page 13

5

10

12

1

3

6

7

4

8

9

11

13

2

Service Parts

Order replacement

parts by Part No.,

not by Key No.

Key No. Part No. Description

1 97018349 Mounting Frame

2 97018721 Knockout Plate & Screws

3 97018382 Housing

4 97020893 Wiring Panel/Harness Assembly

5 97020849 Control Assembly & Motor (XB50L1)

97020848 Control Assembly & Motor (XB80L1)

97020847 Control Assembly & Motor (XB110L1)

6 97018331 Duct Connector - 6"

7 99111513

6" to 4" Reducer (models XB50L1 and XB80L1 only)

8 99020301 Blower Wheel

9 97019371 Scroll Assembly (XB50L1, XB80L1)

97018768 Scroll Assembly (XB110L1)

10 97020827 Grille Assembly (includes 11, 12)

11 99140208 Grille Spring (2 req’d)

12 99111711 Lens (2 req’d)

13 99271625 LED Driver

Broan Ventilation Fan/Lights Limited Warranty

WARRANTY PERIOD: Broan warrants to the original consumer purchaser of its

Broan Ventilation Fan/Light (the “Fan”) that your Fan (excluding lamps/bulbs) will

be materially free from defects in materials or workmanship for a period of three

(3) years from the date of original purchase. The warranty on the lamps/bulbs

provided with the Fan is one (1) year and does not cover lamp/bulb breakage.

This warranty does not cover accessories, such as speed controls, that may be

purchased separately and installed with the Fan.

The limited warranty period for replacement parts, and for Fans repaired or

replaced under this limited warranty, shall continue for the remainder of the

original warranty period.

NO OTHER WARRANTIES: THE FOREGOING WARRANTIES ARE

EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR

IMPLIED. BROAN DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS

WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES

IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TO THE

EXTENT THAT APPLICABLE LAW PROHIBITS THE EXCLUSION OF IMPLIED

WARRANTIES, THE DURATION OF ANY APPLICABLE IMPLIED WARRANTY

IS LIMITED TO THE PERIOD SPECIFIED FOR THE EXPRESS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you. Any oral or written description of the

Fan is for the sole purpose of identifying it and shall not be construed as an

express warranty.

REMEDY: During the applicable limited warranty period, Broan will, at its

option, provide replacement parts for, or repair or replace, without charge,

any Fan or part thereof, to the extent Broan finds it to be covered by and in

breach of this limited warranty. Broan will ship the repaired or replaced Fan

or replacement parts to you at no charge. You are responsible for all costs for

removal, reinstallation and shipping, insurance or other freight charges incurred

in the shipment of the Fan or part to Broan. This warranty does not cover (a)

normal maintenance and service, (b) normal wear and tear, (c) any Fans or

parts which have been subject to misuse, abuse, abnormal usage, negligence,

accident, improper or insufficient maintenance, storage or repair (other than

repair by Broan), (d) damage caused by faulty installation, or installation or use

contrary to recommendations or instructions, (e) any Fan that has been moved

from its original point of installation, (f) damage caused by environmental or

natural elements, (g) damage in transit, (h) natural wear of finish, (i) Fans in

commercial or nonresidential use, or (j) damage caused by fire, flood or other

act of God. This warranty covers only Fans sold in the United States or through

U.S. distributors authorized by Broan.

EXCLUSION OF DAMAGES: BROAN’S OBLIGATION TO PROVIDE

REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT BROAN’S OPTION,

SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY AND BROAN’S SOLE AND EXCLUSIVE OBLIGATION. BROAN

SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR

SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE FAN,

ITS USE OR PERFORMANCE. Incidental damages include but are not limited

to such damages as loss of time and loss of use. Consequential damages

include but are not limited to the cost of repairing or replacing other property

which was damaged if the Fan does not work properly.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to

you. This warranty gives you specific legal rights, and you may also have other

rights, which vary from state to state.

This warranty supersedes all prior warranties and is not transferable from the

original consumer purchaser.

BROAN SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER

YOU, FOR ANY OTHER OBLIGATIONS OR LIABILITIES, INCLUDING, BUT

NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH

OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY

THEORY OF STRICT LIABILITY, WITH RESPECT TO THE FAN OR BROAN’S

ACTS OR OMISSIONS OR OTHERWISE.

This warranty covers only replacement or repair of defective Fans or parts

thereof at Broan’s main facility and does not include the cost of field service

travel and living expenses.

Any assistance Broan provides to or procures for you outside the terms,

limitations or exclusions of this limited warranty will not constitute a waiver of

such terms, limitations or exclusions, nor will such assistance extend or revive

the warranty.

Broan will not reimburse you for any expenses incurred by you in repairing or

replacing any defective Fan, except for those incurred with Broan’s prior written

permission.

HOW TO OBTAIN WARRANTY SERVICE: To qualify for warranty service, you

must (a) notify Broan at the address or telephone number stated below within

seven (7) days of discovering the covered defect, (b) give the model number and

part identification and (c) describe the nature of any defect in the Fan or part.

At the time of requesting warranty service, you must present evidence of the

original purchase date.

Broan, 926 West State Street, Hartford, WI 53027

(1-800-637-1453)

www.broan.com

If you must send the Fan or part to Broan, as instructed by Broan, you must

properly pack the Fan or part—Broan is not responsible for damage in transit.

Warranty

99045908A

XB50L1

n

XB80L1

n

XB110L1

X1 | Ventilador para ventilación

con una única velocidad,

con iluminación regulable

GUÍA PARA LA INSTALACIÓN

LEA Y CONSERVE ESTAS INSTRUCCIONES

Instalador: entregue esta guía al dueño de casa.

Registre su producto en línea en el sitio www.broan.com/register.

Instalación sencilla tanto en

construcciones nuevas como

en modernizaciones

Tabla de contenido

Advertencias y precauciones 2

Instalación típica 2

Instalación en una construcción nueva 3

Instalación en modernizaciones 7

Funcionamiento 12

Limpieza y mantenimiento 12

Identificación y solución de fallas 12

Repuestos 13

Garantía 13

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 2

ADVERTENCIA

PARA REDUCIR EL RIESGO DE INCENDIO, SHOCK ELÉCTRICO

O DAÑOS A LAS PERSONAS, RESPETE LAS SIGUIENTES

INSTRUCCIONES:

1. Utilice esta unidad sólo para el uso que describe el fabricante.

Si tiene alguna pregunta, comuníquese con el fabricante a la

dirección o al número de teléfono que aparece en la garantía.

2. Antes de realizar el servicio o de limpiar la unidad, corte el

suministro eléctrico en el panel de servicio y bloquee el servicio

desconectando los medios que evitan que se conecte la energía

en forma accidental. Cuando no se puedan bloquear los medios

que desconectan el servicio, coloque un dispositivo de alarma

importante, como por ejemplo una etiqueta, en el panel de

servicio.

3. Las tareas de instalación y el cableado eléctrico deben ser

realizados por una persona/personas calificada/s según lo

establecen todos los códigos y las normas aplicables, entre los

que se incluyen códigos y normas para las construcciones con

calificación contra incendios.

4. Se requiere suficiente aire para una correcta combustión y escape

de gases a través del regulador de tiro (chimenea) del equipo

que funciona a combustible para evitar contracorrientes. Siga las

indicaciones del fabricante del equipo de calefacción y las normas

de seguridad como las publicadas por la Asociación Nacional de

Protección contra Incendios (NFPA) y la Sociedad Estadounidense

de Ingenieros en Calefacción, Refrigeración y Aire Acondicionado

(ASHRAE) y las autoridades locales regulatorias.

5. Al cortar o perforar las paredes o los techos, no dañe el cableado

eléctrico u otros servicios que no se encuentran a la vista.

6. Los ventiladores conectados a conductos siempre deben tener

ventilación hacia el exterior.

7. Use solamente un interruptor de ENCENDIDO/APAGADO, un

temporizador mecánico o un control de relé-interruptor.

8. La unidad sólo debe conectarse a un circuito de alimentación

protegido por un interruptor de circuito para fallas con conexión a

tierra (ICFT).

9. Esta unidad debe estar conectada a tierra.

Instalación típica

PRECAUCIÓN

1. Sólo debe utilizarse para ventilación general. No utilizar para

ventilar materiales y vapores peligrosos o explosivos.

2. Este producto está diseñado para instalarse en techos con

una pendiente de hasta 12/12 (ángulo de 45 grados).

El conector del conducto debe estar orientado hacia arriba.

NO MONTAR ESTE PRODUCTO SOBRE LA PARED.

3. Para evitar daños en los cojinetes del motor y/o impulsores

desbalanceados y ruidosos, mantenga el rociado para los

paneles de yeso, el polvo de la construcción, etc., lejos de la

unidad eléctrica.

4. Lea la etiqueta con las especificaciones del producto para

obtener más información y conocer los requisitos.

45° 45°

• La instalación es similar para:

• Se adapta a la construcción de un

techo de 5 cm x 20 cm (2 x 8 pulg.)

• Ajustar sin límite la posición del

ventilador entre las vigas a una

distancia de 35,5 cm a 61 cm

(14 a 24 pulg.) del centro.

NO UTILIZAR EN UN ÁREA DONDE SE COCINA

No instalar sobre o dentro de esta área

Piso

Artefacto para

cocinar

Vigas Vigas en Cerchas

forma de I

*Comprar por separado.

AISLACIÓN*

(Colocar alrededor y sobre

el compartimiento para el ventilador).

CAPUCHÓN

PARA TEJADO*

(con regulador

de tiro

incorporado)

VENTILADOR

COMPARTIMIENTO

CABLE DE

ALIMENTACIÓN*

CONDUCTO

CIRCULAR*

CODOS

CIRCULARES*

Sellar las

cavidades

alrededor del

compartimiento.

Sellar las uniones

del conducto

con cinta.

O

Asegurarse

de que los

conductos

sean cortos.

CAPUCHÓN

DE PARED*

(con regulador

de tiro incorporado)

Los conductos desde este ventilador hacia el exterior del edificio tienen un gran efecto sobre el flujo de aire, el ruido y el uso de energía

del ventilador. Utilice el tramo de conductos más corto y recto posible para obtener un desempeño óptimo y evite instalar el ventilador

con conductos menores que los recomendados. El aislamiento alrededor de los conductos puede reducir la pérdida de energía e inhibir

el desarrollo de moho. Los ventiladores instalados en conductos existentes podrían no obtener el flujo de aire nominal.

Para un mejor desempeño, se recomienda utilizar conductos metálicos redondos y rígidos de 6 pulg. (15.2 cm).

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 3

1

2

3

4

La bolsa de las

piezas contiene

una placa

metálica y seis

(6) pernos

Retire la hoja de

instrucciones

Retire la máscara del

envase. Consulte el Paso 6.

Instalación en una construcción nueva

Herramientas necesarias

• Destornillador eléctrico con punta Phillips

• Destornillador Phillips

• Destornillador de cabeza plana

• Pinza

• Pelacable para la aislación de los cables

• Pinza cortacable

Materiales necesarios

• Conducto circular de metal de 6 pulg. recomendado para un mejor

rendimiento.

Se acepta el uso de otro tipo de conducto pero esto puede afectar el rendimiento.

• Capuchón para tejado o de pared (se recomienda utilizar uno con regulador

de tiro incorporado)

• Cinta para sellar las conexiones de los conductos

• Cables y accesorios eléctricos en cumplimiento de la normativa local

1

Retire el envase

2

Instale

el bastidor

de montaje

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 4

3

1

4

2

1

2

3

Instalación en una construcción nueva

3

Coloque el

compartimiento

a presión

y asegúrelo

4

Fije el conector del conducto y los conductos

Ubique el compartimiento

entre las vigas y ajuste el

canal a ambos lados del

bastidor de montaje para

que el compartimiento

quede asegurado

en su lugar.

No ajuste el

compartimiento.

Pernos de la bolsa de piezas

Las bridas superior e inferior

deben ir por fuera del compartimiento

Introduzca la pestaña en

la ranura en el interior del

compartimiento

Perno de la

bolsa de

piezas

Algunos modelos cuentan con un

adaptador de 6 a 4 pulg.

Cinta

Conducto

de 6 pulg.

Conducto

de 4 pulg.

¡Presione

hasta que

trabe!

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 5

3

4

1

2

Instalación en una construcción nueva

5

Conecte los cables e instale la placa metálica

• Extienda un cableado eléctrico de 120 VCA hasta el sitio de la instalación.

• Utilice conectores aprobados por UL para asegurar el cableado hasta la placa metálica que se incluye en la bolsa de piezas.

• Conecte los cables como se muestra en el diagrama de cableado.

Perno de la

bolsa de

piezas

Fije las abrazaderas de los

cables a la placa metálica.

La placa metálica debe

montarse

en el exterior del

compartimiento

y se la puede ubicar

en la dirección deseada.

Conecte los cables

LINEA

DE

ENTRADA

TRA

BLC

NEG

TRA

BLC

NEG

ROJ AZL

ROJ

NEG

INTERRUPTOR

DE LUZ

INTERRUPTOR

DE VENT.

VENT.

LUZ

UNIDADCAJA DE INTERRUPTORES

TRA

BLC

NEG

TRA

BLC

NEG

ROJ AZL

ROJ

NEG

REGULADOR DE

INTENSIDAD

INTERRUPTOR

DE VENTILATOR

VENT.

LUZ

LINEA

DE

ENTRADA

UNIDADCAJA DE INTERRUPTORES

LUZ CON INTERRUPTOR DE ENCENDIDO / APAGADO

LUZ CON REGULADOR DE INTENSIDAD

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 6

1

2

3

1

Instalación en una construcción nueva

6

Introduzca la

máscara y

acondicione

el techo

7

Instale la rejilla

La máscara protege

la unidad durante la

construcción. Retírela

antes de instalar la

rejilla.

• Instale el material del techo.

• Corte alrededor del

compartimiento.

PRECAUCIÓN

Si el motor estaba desconectado, se debe desconectar la

electricidad (vea la página 2, ADVERTENCIA, punto 2) antes

de insertar los enchufes del motor en el conjunto de control.

PARA PREVENIR DAÑOS EN EL MOTOR/CONTROL:

1

2

3

1

XB50L1

n

XB80L1

n

XB110L1 Guía para la instalación

Página 7

12" (30.5 cm)

1

2

Instalación en modernizaciones

La bolsa de

las piezas

contiene una

placa metálica

y seis (6) pernos

Los conductos existentes

y los cables permanecerán

en su sitio

ADVERTENCIA

Antes de retirar el ventilador existente, desconecte el suministro eléctrico en el panel de servicio y bloquee el servicio

desconectando los medios para evitar que se active el suministro de energía en forma accidental. Cuando no se

puedan bloquear los medios que desconectan el servicio, coloque un dispositivo de alarma importante, como por

ejemplo una etiqueta, en el panel de servicio.

Verifique el cableado existente para asegurarse de que no esté dañado. En caso de determinar algún daño,

NO CONTINÚE CON LA INSTALACIÓN de este producto. Comuníquese con la(s) persona(s) calificada(s)

para realizar la reparación.

Retire la hoja de

instrucciones

Retire la máscara del

envase. Consulte el Paso 12.

1

Retire el envase

2

Desconecte el suministro de energía

4

Verifique el cableado

3

Aumente la abertura del techo y retire el ventilador existente

• Regla

• Lápiz

• Sierra para paneles de yeso

• Martillo de orejas o palanca

• Cuchillo multiuso

Herramientas necesarias

• Destornillador eléctrico con punta Phillips

• Destornillador Phillips

• Destornillador de cabeza plana

• Pinza

• Pelacable para la aislación de los cables

• Pinza cortacable

27,9 cm (11 pulg.)

paralelo a las vigas

Materiales necesarios

• Cinta para sellar las conexiones de los

conductos

•

Los conductos rígidos existentes requerirán el

agregado de tramos cortos de un conducto

flexible

• Cables y accesorios eléctricos en

cumplimiento de la normativa local

La page charge ...

Broan XB50L1 Mode d'emploi

Ce manuel convient également à

Broan XB50L1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents