P/N 057286-003
1545 Bar Code Laser Scanner
User’s
Guide
6001 36th Avenue West
PO Box 4280
Everett, WA 98203-9280
Phone (206) 348-2600
P/N 057286-003
© 1995 Intermec Corporation
Regulatory Statements
• This device meets Class B limit requirements of CISPR 22.
SPECIFICATIONS SAFETY APPROVALS
LASER PRODUCT USE - UL Listed, UL 1950 1st Edition
USA - CDRH Class II Canada - CSA Certified C22.2 - 220/M1986
International - IEC 825 Class 2 Europe - TUV Rheinland Licensed
EN 60 950 (IEC 950)
and DIN IEC 825
The 1545 Laser Scanner is UL Listed, CSA Certified and TUV licensed when used with
Intermec's Models 944X, 946X, 9450, 951X, 954X, 955X, 956X, 957X, 971X, 972X,
J2010X and J205X Readers. It is UL Listed for use with other readers, only when these
readers are UL Listed with Class 2 outputs.
Patent Information
This scanner is the subject of patents applied for by Intermec. This scanner is also protected
by one or more of the following U.S. patents and equivalent foreign patents:
4,334,301 4,387,297
4,409,470 4,593,186
4,760,248 4,816,660
Introduction
Introduction
1545
1545UG-002
The Intermec 1545 series laser scanners deliver quick,
effortless bar code scanning and can read even marginal quality
bar codes almost instantly. The scanners are reliable and can
withstand demanding industrial applications. With their low
power solid state visible laser diode, the 1545s are particularly
appropriate for portable applications. A 1545 with a fully
charged reader can be used for a full day of data collection.
1545E
General purpose scanner, 670 nm light.
1545F
Has added capability of being compatible with specific third
party readers, 670 nm light.
1545G
Same as 1545E, except its 650 nm light appears brighter.
Regulatory Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
can cause undesired operation.
Federal Communications Commission Compliance
This equipment is intended for operation in a commercial environment, in
compliance with the requirements for a Class A digital device, pursuant to Part 15
of the FCC Rules, and it must not be used in a residential environment; however,
it has also been tested and found to comply with the more stringent requirements
for a Class B device, pursuant to Part 15 of the FCC Rules. It generates, uses and
can radiate radio frequency energy. If not installed and used in accordance with
the instruction manual, it may cause interference to radio communications. If this
equipment causes interference, the user will be required to correct the interference
at the user’s own expense.
Note: In order to maintain compliance with FCC Rules, the l/O cables that
interconnect between the device and any peripheral (such as a printer, external
modem, etc.) must be shielded and the cable shield grounded as specified by
Intermec.
Caution: Changes or modifications not expressly approved by Intermec could void
the user’s authority to operate this equipment.
Industry Canada Compliance
This digital apparatus does not exceed the Class B limits for radio emissions from
digital apparatus as set out in the radio interference regulations of Industry
Canada.
Cet appareil numérique n’émet pas de bruits radioéléctriques dépassant les limites
applicables aux appareils numériques de Classe B préscrites dans le réglement sur
le brouillage radioéléctrique édicté par Industrie Canada.
Additional EMI/RFI Compliance
• This device complies with the requirements of / Cet appreil en conformite avec /
Dieses Gerät befolgt auf die Ausführungsbestimmungen des:
EN55022 (Class B limits) and EN50082-1.
Installation
1545UG-003
3
1
Unpack the scanner
and inspect it for
physical damage.
Connect cable to reader
(scanner plug to reader socket).
1545UG.007
1
2
3
keyboard
terminal
input
audio
power
1
2
3
keyboard
terminal
input
audio
power
1545UG-006
97XX Reader
2
Connect cable to scanner
(cable sold separately).
Laser Safety Information
LASERSTRAHLUNG - NICHT
IN DEN STRAHL BLICKEN
1.0mW - 650/670nm
LASER KLASSE 2
VDE 0837/0286
IEC 825 : 1984 HD 482 : S1
IEC 825 : 1984 HD 482 : S1
RADIAZIONE LASER
NON FISSARE IL FASCIO
APPARECCHIO LASER DI CLASSE 2
In Accordo con la Norma CEI 76-2 (1984)
1.0mW - 650/670nm
IEC 825 : 1984
HD 482 : S1
LASER LIGHT - DO NOT
STARE INTO BEAM
CLASS 2 LASER PRODUCT
1.0mW - 650/670nm
IEC 825 : 1984
NF C43-801 HD 482 : S1
APPAREIL A RAYONNEMENT
LASER DE CLASSE 2
RAYONNEMENT LASER - NE PAS
REGARDER DANS LE FAISCEAU
1.0mW - 650/670nm
IEC ENGLISH
FRENCH
GERMAN
ITALIAN
NORWEGIAN - DANISH
IEC 825 : 1984
CEI 825 : 1984
SPANISH
JAPANESE
IEC 825 : 1984
SWEDISH / FINNISH
IEC 825 : 1984
HD 482 : S1
SSIFS 1980 : 2
LASERSTRÅLING
1.0mW - 650/670nm
INN I STRÅLEN
KLASSE 2 LASER PRODUKT
STIRR IKKE
LUZ LASER - ¡NO
MIRE HACIA EL RAYO!
1.0mW - 650/670nm
CATEGORIA 2
PRODUCTO LASER
HD 482 : S1
NEK-HD 482 : S1(1988)
1.0mW - 650/670nm
LASERSTRÅLNING
VARNING
I STRÅLEN
LASER DIODE
KLASS 2
STIRRA EJ IN
VAARA
LASERSATEILYA
ALA TUIJOTA
SATEESEEN
LUOKAN 2 LASER
:1mW
670nm
650/
:
1545UG-020
Installation
9450 Reader
1545UG-004
9440
944X Reader
1545UG-009
®
1545UG-008
95XX Reader
1545UG-021
J2010X Reader
Laser Safety Information
LASER LIGHT-DO NOT
STARE INTO BEAM
670nm LASER DIODE
1.0 MILLIWATT MAX
CLASS II LASER PRODUCT
CAUTION
ATTENTION
PRODUIT LASER CLASSE II
LUMIER LASER - NE PAS
REGARDER DANS LE FAISCEAU
1545UG-019
The following additional labels are provided
with the 1545 when the product is used outside
of the USA or Canada. One of these labels is
intended to be placed over the existing label.
See the 1545 Label Application Instruction
Sheet for correct orientation and placement of
the label.
Note: Laser light is emitted from the aperture
window at the front of the unit.
1545UG-005
946X Reader
Cables
The type of cable used with the 1545 Laser Scanner depends
on the type of reader to which it is attached. Compatible
Intermec readers include:
944X Portable Readers
946X Portable Readers
9450 RF Vehicle Mount Readers
95XX Wedge/Network Readers
97XX Wedge Readers
J2010X Terminals
*123456*
1545UG-010
There are no connecting cables shipped with the scanner. These are
purchased separately.
Reader Length Cable Connection P/N
944X 5ft (1.24m) 6 Pin Modular 052900
944X 25ft (7.63m) 6 Pin Modular 052904
95XX 6ft (1.83m) 9 Pin D-Subminiature 052901
95XX 25ft (7.63m) 9 Pin D-Subminiature 052906
946X, 9450 6ft (1.83m) 11 Pin Sealed 052902
9450 15ft (3.72m) 11 Pin Sealed 055056
97XX 6ft (1.83m) 10 Pin Modular 054361
97XX 25ft (7.63m) 10 Pin Modular 054362
J2010X 6ft (1.83m) 10 Pin Modular 054361
J2010X 25ft (7.63m) 10 Pin Modular 054362
3rd Party 6ft (1.83m) 9 Pin D-Subminiature *055097
*1545F only
Cable Connections for the 1545 Laser Scanner
Accessories
1545UG-011
Holster and Belt
(Part Number 053175)
WARNING
Do not look directly into the window area or at a reflection of the laser beam
while the laser is scanning. Long term exposure to the laser beam can damage
your vision.
AVERTISSEMENT
Ne regardez pas directement la réflexion d'un rayon laser ou dans la fenêtre du
laser lorsque celui-ci est en opération. Si vous regardez trop longtemps un
rayon laser, cela peut endommager votre vision.
CAUTION
There are no user serviceable parts inside the 1545. Use of controls or
adjustments or performance of procedures other than those specified herein
may result in hazardous laser light exposure of up to 2mW at 650 or 670 nm.
NOTE: There are no controls or adjustments provided for routine operation and
maintenance of the 1545.
ATTENTION
La 1545 ne contient pas de pièces révisibles par l'utilisateure. L'emploi de
commandes ou d'ajustements ou de performances des procédures autres que
ceux précisés dans cette documentation pourrait avoir comme résultat l'exposi-
tion à l'irradiation laser nuisible de jusqu'à 2mW à 650 ou 670 nm.
NOTE: Vous ne disposez k'aucun controle ni reglage pour le
fonctionnement et l'entetier courants du 1545.
Laser Safety Information
Troubleshooting & Laser Safety Information
AVOID
EXPOSURE
Laser light is
Emitted from
this Aperture
EVITER
TOUTE
EXPOSITION
Lumiere Laser
Emis par cette
Ouverture
1545
AVOID
EXPOSURE
Laser light is
Emitted from
this Aperture
EVITER
TOUTE
EXPOSITION
Lumiere Laser
Emis par cette
ouverture
1545
1545UG-018
Document Stand
The document stand requires that two interface cables be
purchased before use: one to connect it to the reader and
another to connect it to the scanner.
Doc. Stand Scanner to
to Reader Doc. Stand
Reader Cable P/N Cable P/N
95XX 054866 052901
97XX 054867 052901
To Reader
Doc. Stand
1545UG-014
• For portable readers, a double beep after a successful read
indicates that the reader batteries are low.
• Damage to the 1545 may result if these temperature ranges
are exceeded:
Operating Temperature:
-4° to 122°F (-20° to 50°C)
Storage Temperature:
-40° to 158°F (-40° to 60°C)
• The scanner has built-in sensing circuitry that protects the
laser diode from high temperatures. The green “READ”
indicator light blinks if this circuitry has turned off the laser.
• If you have difficulty operating the scanner, determine if the
problem originates with the bar code, the scanner, the cable,
or the reader:
1. Try scanning printed bar code that is known to be machine
readable.
2. Clean the scanner window. Use a dry, soft cloth, but do not
use water, solvents, or cleaning agents; doing so will
damage the scanner window. Follow the scanning tips
described in this quick reference guide.
3. Replace the cable with a cable known to be in good working
condition.
4. Refer to the troubleshooting section of the user manual for
your reader.
• There are no user serviceable parts in the 1545 Laser Scanner.
For information on the nearest repair depot, contact your
local Intermec representative.
Troubleshooting
1545UG-013
Cables & Accessories
Operation
1. Switch on reader.
2. Aim scanner close to bar code and
squeeze trigger.
3. When you get a successful read:
• The laser beam turns off.
• The reader beeps.
• The green indicator light turns on
(for wedge/network readers only).
1545
1545UG-001
*123*
WRONG
The scan line must cross every bar
and space on the symbol.
Range of
Operation
*123*
The less dense the bar code, the greater the
reading range of the scanner.
For each density of bar code there is an
optimum reading distance. Start out close to
the bar code and move back from there.
If you fail to get a quick read, try moving the
scanner to a point where it is less sensitive to
poorly printed or distorted bar code.
Water or grime on the window of the scanner
will distort the laser beam and impair perfor-
mance:
• Clean the scanner window using a dry, soft
cloth. Do not use water, solvents or cleaning
agents. Doing so will damage the scanner
window.
• Operate and store in an environment of 0-95%
relative humidity.
• DO NOT submerse the unit in water.
• DO NOT use a dry tissue to wipe the window.
Angle of
Operation
For a quick read, hold the scanner at a slight
angle to the bar code.
Operation
*123*
Vertical
reading
angles (pitch)
1545UG-015
*123*
Horizontal
reading
angles (skew)
1545UG-017
Dead Zone
Reflected light
may prevent
a good read
when you aim
straight on.
1545UG-016
Maintenance
RIGHT
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
