Ryobi PBLMS01B Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
10 in. 18V SLIDING COMPOUND
MITER SAW WITH LED
SCIE À ONGLETS COMBINÉS
COULISSANTE DE 254 mm (10 po)
DE18V AVECDEL
SIERRA INGLETEADORA COMPUESTA
DESLIZANTE DE 254 mm (10 pulg.)
DE18V CONLED
PBLMS01
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT :
Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
TABLE OF CONTENTS
****************
General Safety Rules ...................... 2-3
Miter Saw Specific Safety Rules ........4
Additional Safety Rules ......................5
Symbols ..............................................6
Glossary of Terms ...............................7
Features ........................................ 8-10
Tools Needed ...................................11
Loose Parts List ................................11
Assembly .................................... 12-21
Operation .................................... 22-31
Adjustments .....................................32
Maintenance ............................... 33-34
Parts Ordering / Service ..... Back Page
TABLE DES MATIÈRES
****************
Règles de sécurité générales ......... 2-3
Règles de sécurité scie à onglets ... 3-4
Règles de sécurité supplémentaires .......5
Symboles ............................................6
Glossaire .............................................7
Caractéristiques ........................... 8-10
Outils nécessaires ............................11
Liste des pièces détachées ..............11
Assemblage ................................ 12-21
Utilisation .................................... 22-32
Réglages ...........................................33
Entretien ...........................................34
Commande de pièces /
réparation ..........................Page arrière
ÍNDICE DE CONTENIDO
****************
Reglas de seguridad generales ...... 2-3
Reglas de seguridad sierra
ingleteadora ................................... 3-4
Advertencias de seguridad
adicionales .........................................5
Símbolos ............................................6
Glosario de términos ..........................7
Características.............................. 8-10
Herramientas necesarias ..................11
Lista de piezas sueltas .....................11
Armado ....................................... 12-21
Funcionamiento .......................... 22-32
Ajustes ..............................................33
Mantenimiento ..................................34
Pedidos de piezas /
servicio .......................... Pág. posterior
2 − English
GENERAL SAFETY RULES
WARNING:
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is un-
avoidable, use a ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI reduces the risk of
electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
3 − English
GENERAL SAFETY RULES
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes, ad-
ditionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion, or risk
of injury.
Do not expose a battery pack or tool to fire or exces-
sive temperature. Exposure to fire or temperature above
265° F may cause explosion.
Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
Use battery only with charger listed. For use with 18V
lithium-ion battery packs, see tool/appliance/battery pack/
charger correlation supplement 987000-432.
Battery tools do not have to be plugged into an elec-
trical outlet; therefore, they are always in operating
condition. Be aware of possible hazards when not
using your battery tool or when changing accessories.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and pos-
sibly injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
Do not charge battery tool in a damp or wet location.
Do not use, store, or charge battery packs or products
in locations where the temperature is less than 50°F
or more than 100°F. Do not store outside or in vehicles.
Under extreme usage or temperature conditions, bat-
tery leakage may occur. If liquid comes in contact with
your skin, wash immediately with soap and water. If
liquid gets into your eyes, flush them with clean water
for at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of seri-
ous personal injury.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
tery packs should only be performed by the manufacturer
or authorized service providers.
4 − English
MITER SAW SPECIFIC SAFETY RULES
Miter saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods,
studs, etc. Abrasive dust causes moving parts such as
the lower guard to jam. Sparks from abrasive cutting will
burn the lower guard, the kerf insert and other plastic
parts.
Use clamps to support the workpiece whenever pos-
sible. If supporting the workpiece by hand, you must
always keep your hand at least 100 mm from either
side of the saw blade. Do not use this saw to cut pieces
that are too small to be securely clamped or held by
hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from blade contact.
The workpiece must be stationary and clamped or
held against both the fence and the table. Do not feed
the workpiece into the blade or cut ”freehand” in
any way. Unrestrained or moving workpieces could be
thrown at high speeds, causing injury.
Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the
saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down
and push the saw through the workpiece. Cutting on
the pull stroke is likely to cause the saw blade to climb
on top of the workpiece and violently throw the blade
assembly towards the operator.
Never cross your hand over the intended line of cutting
either in front or behind the saw blade. Supporting the
workpiece ”cross handed” i.e. holding the workpiece
to the right of the saw blade with your left hand or vice
versa is very dangerous.
Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to
remove wood scraps, or for any other reason while
the blade is spinning. The proximity of the spinning saw
blade to your hand may not be obvious and you may be
seriously injured.
Inspect your workpiece before cutting. If the workpiece
is bowed or warped, clamp it with the outside bowed
face toward the fence. Always make certain that there
is no gap between the workpiece, fence and table
along the line of the cut. Bent or warped workpieces can
twist or shift and may cause binding on the spinning saw
blade while cutting. There should be no nails or foreign
objects in the workpiece.
Do not use the saw until the table is clear of all tools,
wood scraps, etc., except for the workpiece. Small
debris or loose pieces of wood or other objects that con-
tact the revolving blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked multiple
workpieces cannot be adequately clamped or braced
and may bind on the blade or shift during cutting.
Ensure the miter saw is mounted or placed on a
level, firm work surface before use. A level and firm
work surface reduces the risk of the miter saw becoming
unstable.
Plan your work. Every time you change the bevel or
miter angle setting, make sure the adjustable fence
is set correctly to support the workpiece and will
not interfere with the blade or the guarding system.
Without turning the tool ”ON” and with no workpiece
on the table, move the saw blade through a complete
simulated cut to assure there will be no interference or
danger of cutting the fence.
Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or longer
than the table top. Workpieces longer or wider than the
miter saw table can tip if not securely supported. If the
cut-off piece or workpiece tips, it can lift the lower guard
or be thrown by the spinning blade.
Do not use another person as a substitute for a table
extension or as additional support. Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling
you and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by
any means against the spinning saw blade. If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
Always use a clamp or a fixture designed to properly
support round material such as rods or tubing. Rods
have a tendency to roll while being cut, causing the blade
to bite and pull the work with your hand into the blade.
Let the blade reach full speed before contacting the
workpiece. This will reduce the risk of the workpiece
being thrown.
If the workpiece or blade becomes jammed, turn the
miter saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/or re-
move the battery pack. Then work to free the jammed
material. Continued sawing with a jammed workpiece
could cause loss of control or damage to the miter saw.
After finishing the cut, release the switch, hold the
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete
cut or when releasing the switch before the saw head
is completely in the down position. The braking action
of the saw may to be suddenly pulled downward, causing
a risk of injury.
Save these instructions. Refer to them frequently and
use to instruct other users. If you loan someone this tool,
loan them these instructions also.
5 − English
ADDITIONAL SAFETY RULES
Inspect tool cords periodically. If damaged, have re-
paired by a qualified service technician at an authorized
service facility. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
Inspect extension cords periodically and replace if
damaged.
Polarized plugs. To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any
way.
Know your power tool. Read the operator’s manual
carefully. Learn the applications and limitations as well
as the specific potential hazards related to this tool.
Always wear eye protection with side shields which
is marked to comply with ANSI Z87.1 when using this
product. Failure to do so could result in objects being
thrown into your eyes, resulting in possible serious injury.
Never stand on tool. Serious injury could occur if the tool
is tipped or if the cutting tool is unintentionally contacted.
Keep guards in place and in good working order.
Use the right direction of feed. Feed work into a blade,
cutter, or sanding spindle against the direction of rotation
of the blade, cutter, or sanding spindle only.
Never leave tool running unattended. Turn the power
off. Don’t leave tool until it comes to a complete stop.
Use only correct blades. Do not use blades with incorrect
size holes. Never use blade washers or blade bolts that
are defective or incorrect. The maximum blade capacity
of your saw is 10 in.
Before making a cut, be sure all adjustments are
secure.
Never touch blade or other moving parts during use.
Double check all setups. Make sure blade is tight and
not making contact with saw or workpiece before con-
necting to power supply.
Firmly clamp or bolt your tool to a workbench or table
at approximately hip height.
Make sure the miter table and saw arm (bevel func-
tion) are locked in position before operating your saw.
Lock the miter table by pushing the miter lock lever down.
Lock the saw arm (bevel function) by securely tightening
the bevel lock knob.
Never move the workpiece or make adjustment to any
cutting angle while the saw is running and the blade
is rotating. Any slip can result in contact with the blade
causing serious personal injury.
Avoid awkward operations and hand positions where a
sudden slip could cause your hand to move into the blade.
ALWAYS make sure you have good balance. NEVER
operate your miter saw on the floor or in a crouched
position.
Never stand or have any part of the body in line with the
path of the saw blade.
Do not turn the motor switch on and off rapidly. This
could cause the saw blade to loosen and could create
a hazard. Should this ever occur, stand clear and allow
the saw blade to come to a complete stop. Disconnect
your saw from the power supply and securely retighten
the blade bolt.
If any part of this miter saw is missing or should break,
bend, or fail in any way, or should any electrical compo-
nent fail to perform properly, shut off the power switch,
remove the miter saw plug from the power source and
have damaged, missing, or failed parts replaced before
resuming operation.
Always turn off the saw before disconnecting it to avoid
accidental starting when reconnecting to power supply.
NEVER leave the saw unattended while connected to a
power source.
This tool should have the following markings:
To reduce the risk of injury, user must read the opera-
tor’s manual.
Wear eye protection.
Keep hands and body out of the path of the saw blade.
Contact with the blade will result in serious injury.
Check guarding system to make sure it is functioning
correctly.
Do not perform any operation freehand.
Never reach around the saw blade.
Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
Disconnect the saw from the power source before
changing blade or servicing.
Always carry the tool only by the carrying handle.
This saw can tip over if the saw head is released sud-
denly and the saw is not secured to a work surface. Always
secure this saw to a stable work surface before any use
to avoid serious personal injury.
Always make sure the saw blade has clearance of
all obstructions before turning the saw on.
6 − English
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand opera-
tor’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
No Hands Symbol Failure to keep your hands away from the blade will result in seri-
ous personal injury.
Extremely Bright Light This product uses extremely bright LEDs. To avoid serious eye
injury, do not stare into the light (not even from a distance).
Wet Conditions Alert Do not expose to rain or use in damp locations.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
SYMBOLS
7 − English
GLOSSARY OF TERMS
Pilot Hole (drill presses and scroll saws)
A small hole drilled in a workpiece that serves as a guide
for drilling large holes accurately or for insertion of a scroll
saw blade.
Push Blocks (jointer planers)
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator’s hands well away from the cutterhead.
Push Blocks and Push Sticks (table saws)
Devices used to feed the workpiece through the saw blade
during cutting operations. When making a narrow rip cut
without a jig or similar cutting aid, always use a push stick (not
a push block). A push block can be used for narrow ripping
operations, if a jig or similar cutting aid is used. These aids
help keep the operator’s hands well away from the blade.
Rabbet
A non-through cut positioned on the end or edge of the
workpiece which produces a square, two-sided notch or
trough in the workpiece.
Resaw (table saws and band saws)
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Ripping or Rip Cut (table saws)
A cutting operation along the length of the workpiece and
typically in the direction of the grain.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Snipe (planers)
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Taper Cut
A cut where the material being cut has a different width at
the beginning of the cut from the end.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece. This type of cut will
separate a single workpiece into two pieces.
Workpiece or Material
The item on which the operation is being done.
Worktable
Surface where the workpiece rests while performing a cutting,
drilling, planing, or sanding operation.
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Chamfer
A cut removing a wedge from a block so the end (or part of
the end) is angled rather than at 90°.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
A cutting or shaping operation made across the grain or the
width of the workpiece.
Cutter Head (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Dado Cut (table saws and compound sliding miter saws)
A non-through cut which produces a square, three-sided
notch or trough in the workpiece.
Featherboard (table saws)
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter fence, or other aids.
Gum
A sticky, sap-based residue from wood products.
Heel
Alignment of the blade to the miter gauge groove.
Kerf
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece in the direction of the spinning blade.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Non-Through Cuts (table saws and compound sliding
miter saws)
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece. This is a
cut where the blade will not cut the workpiece into two pieces.
8 − English
FEATURES
PRODUCT SPECIFICATIONS
Arbor Hole ................................................................. 5/8 in.
Blade Diameter ............................................................10 in.
No Load Speed ........................................4,100/min. (RPM)
Input ................................................................... 18 Volt DC
Cutting Capacity with Miter at 0°/Bevel 0°:
Maximum lumber sizes .......................... 1-1/2 in. x 12 in.
or 3-1/2 in. x 5-1/2 in.
Cutting Capacity with Miter at 45°/Bevel 0°:
Maximum lumber sizes ......................1-1/2 in. x 7-1/4 in.
Cutting Capacity with Miter at 0°/Bevel 45°:
Maximum lumber sizes .......................... 1-1/2 in. x 12 in.
Cutting Capacity with Miter at 45°/Bevel 45°:
Maximum lumber sizes ......................1-1/2 in. x 7-1/4 in.
Fig. 1
BEVEL
SCALE
BEVEL
LOCK KNOB
DEPTH
CONTROL KNOB
DEPTH STOP
LOCK
PIN
SWITCH
TRIGGER
DUST BAG
MITER
FENCE
TABLE
EXTENSION BASE
WORK
CLAMP
MITER
TABLE
CONTROL
ARM
MITER
LOCK HANDLE
“NO HANDS
ZONE” LABEL
“NO HANDS ZONE”
BOUNDARY LINE
MITER
SCALE
UPPER BLADE
GUARD
LOWER BLADE
GUARD
“D”
HANDLE
SLIDE
LOCK KNOB
SLIDE BAR
SUPPORT FOOT
POSITIVE
STOP(S) DETENT RELEASE LEVER
BLADE
WRENCH
THROAT
PLATE
LED
SWITCH
PARTIAL SLIDING
FENCE
CARRYING
HANDLE
9 − English
FEATURES
KNOW YOUR COMPOUND MITER SAW
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
10 IN. BLADE
A 10 in. blade is included with the compound miter saw. It will
cut materials up to 3-1/2 in. thick or 12 in. wide, depending
upon the angle at which the cut is being made.
BEVEL LOCK KNOB
See Figure 2.
The bevel lock knob securely locks your compound miter saw
at desired bevel angles. A positive stop adjustment screw has
been provided on each side of the saw arm. These adjust-
ment screws are for making fine adjustments at 0° and 45°.
CARRYING HANDLE
See Figure 2.
For convenience when carrying or transporting the miter
saw from one place to another, a carrying handle has been
provided on top of the saw arm. To transport, turn off the saw
and remove the battery, then lower the saw arm and lock it in
the down position by pushing in the lock pin.
NOTE: DO NOT perform any cutting operation with the saw
in the locked position.
DETENT OVERRIDE
See Figure 3.
The detent override allows the miter table to move freely to
any desired angle. With the miter lock handle loosened and the
detent release lever squeezed (1), pull the detent override up (2)
and release the detent release lever (3) to bypass the positive
stops on the miter scale. To release the detent override and
allow the miter table to engage the positive stops, squeeze
and release the detent release lever.
ELECTRIC BRAKE
An electric brake has been provided to quickly stop blade
rotation after the switch is released.
LED LIGHTING SYSTEM
The LED casts a shadow of the blade teeth onto the workpiece
for making precision cuts and predicts blade kerf for blade
cut line.
MITER FENCE
The miter fence on the compound miter saw has been pro-
vided to hold your workpiece securely against when making
all cuts. The right side is larger providing additional support.
MITER LOCK HANDLE
See Figure 3.
The miter lock handle securely locks the saw at desired miter
angles. Tighten the handle to lock the saw in place. To release
the saw, loosen the handle and squeeze the detent release lever.
SAW ARM LOCKED IN DOWN POSITION
LOCK
PIN
CARRYING
HANDLE
“D”
HANDLE
MITER
LOCK HANDLE
BEVEL
LOCK KNOB
LED GUIDE
SWITCH
Fig. 2
Fig. 3
1
3
2
DETENT
RELEASE LEVER
DETENT
OVERRIDE
10 − English
SPINDLE
LOCK BUTTON
FEATURES
MITER SCALE
The miter scale has index points provided at 0°, 15°, 22.5°,
30, 31.6°, and 45°.
PARTIAL SLIDING FENCE
The partial sliding fence on your compound miter saw has
been provided to help secure the workpiece when making
straight cuts.
The sliding feature makes it easy to adjust the position of the
partial fence. Loosen the fence screw before attempting to
slide the partial fence. Once the desired position is determined,
tighten the fence screw to secure.
POSITIVE STOPS ON MITER TABLE
Positive stops have been provided at 0°, 15°, 22.5°, 31.6°, and
45° on both the left and right side of the miter table.
NOTE: To bypass the positive stops, squeeze the detent
release lever and lift the detent override. To release the over-
ride, squeeze the detent release lever.
SELF-RETRACTING LOWER BLADE GUARD
The lower blade guard is made of shock-resistant, see-through
plastic that provides protection from each side of the blade.
It retracts over the upper blade guard as the saw is lowered
into the workpiece.
SLIDE BARS
When unlocked, the saw arm will glide forward and backward
the length of the slide bars for cutting various workpiece widths.
SLIDE LOCK KNOB
The slide lock knob locks and unlocks the sliding feature of
this tool.
SPINDLE LOCK BUTTON
See Figure 4.
The spindle lock button locks the spindle and stops the blade
from rotating. Depress and hold the lock button while install-
ing, changing, or removing blade.
SWITCH TRIGGER
See Figure 4.
The saw will not start until you depress the trigger lockout
lever and squeeze the switch trigger. To prevent unauthor-
ized use of the compound miter saw, disconnect it from the
power supply and lock the switch in the OFF position. To lock
the switch, install a padlock (not included) through the hole
in the switch trigger and make certain the switch is inoper-
able. If the switch is still operable with the padlock installed,
a padlock with a larger shackle diameter must be used. Store
the padlock key in another location.
Fig. 4
PADLOCK SWITCH
TRIGGER
SWITCH
TRIGGER
PADLOCK
HOLE
11 − English
LOOSE PARTS LIST
Fig. 6
Table Extensions (2)
Work Clamp
Operator’s Manual (not shown)
Blade Wrench
Carrying Handle
Dust Bag
WORK
CLAMP
DUST BAG
RIGHT TABLE
EXTENSION
LEFT TABLE
EXTENSION
The following items are included with the tool:
WARNING:
The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.
The following tools (not included) are needed for making adjustments or installing the blade:
TOOLS NEEDED
Fig. 5
COMBINATION
SQUARE
SQUARE
BLADE
WRENCH
CARRYING
HANDLE
12 − English
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
Do not connect to power supply until assembly is com-
plete. Failure to comply could result in accidental starting
and possible serious personal injury.
WARNING:
Do not start the compound miter saw without checking
for interference between the blade and the miter fence.
Serious personal injury or damage to the blade could
result if it strikes the miter fence during operation of the
saw.
WARNING:
This saw can tip over if the saw head is released suddenly
and the saw is not secured to a work surface. ALWAYS
secure this saw to a stable work surface before any use
to avoid serious personal injury.
UNPACKING
This product requires assembly.
Carefully lift saw from the carton by the carrying handle
and the saw base, and place it on a level work surface.
WARNING:
Do not use this product if any parts on the
Loose Parts
List
are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer instal-
lation. Use of a product that may have been improperly
assembled could result in serious personal injury.
This saw has been shipped with the saw arm secured in
the down position. To release the saw arm, push down
on the “D” handle, cut the tie-wrap, and pull out on the
lock pin.
WARNING:
The saw arm is spring loaded. Hold the handle down to
prevent it from snapping up when cutting the tie-wrap.
Failure to do so could result in possible serious injury.
Lift the saw arm by the “D” handle. Hand pressure should
remain on the saw arm to prevent sudden rise upon release
of the tie wrap.
Cut the tie wrap at the end of the slide bar. Slide the saw
head to its most rearward position and tighten the slide
lock knob securely.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
The saw is factory set for accurate cutting. After assem-
bling it, check for accuracy. If shipping has influenced
the settings, refer to specific procedures explained in
this manual.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
ASSEMBLY
13 − English
Fig. 8
TRACE HOLES
AT THESE LOCATIONS
FOR HOLE PATTERN
Fig. 7
MOUNTING
SURFACE
SAW BASE
TRACE HOLES
AT THESE LOCATIONS
FOR HOLE PATTERN
MOUNTING HOLES
See Figure 7.
WARNING:
Before starting any cutting operation, clamp or bolt
your miter saw to a workbench or an approved miter
saw stand. If a miter saw stand is used, read operator’s
manual and follow the instructions for the miter saw
stand. Never operate your miter saw on the floor or in a
crouched position. Failure to heed this warning can result
in serious personal injury.
The compound miter saw should be mounted to a firm sup-
porting surface such as a workbench, mounting board, or
miter saw stand. The saw base has four mounting holes. If
using bolts or screws, they should be of sufficient length to
accommodate the saw base, lock washers, hex nuts, and
the thickness of the workbench or other mounting surface.
Tighten all bolts or screws securely.
The hole pattern for mounting to a workbench is shown in
figure 7. Carefully check the workbench after mounting to
make sure that no movement can occur during use. If any
tipping, sliding, or walking is noted, secure the workbench
to the floor before operating.
INSTALL THE CARRYING HANDLE
See Figure 8.
Remove the battery.
Align the handle over the tabs on the top of the saw.
Insert the lock nuts into the pockets.
NOTE: Hold the two lock nuts in place with fingers while
tightening the bolts. Make sure the nylock is to the outside
of the bolt for easier threading.
Insert the bolts through the handle and tabs.
Thread the bolts into the lock nuts.
Tighten the bolts using the blade wrench.
LOCK NUTS
BOLTS
TABS
CARRYING
HANDLE
ASSEMBLY
14 − English
Fig. 10
LOCK
PIN
“D”
HANDLE
Fig. 9
DEPTH
CONTROL KNOB
DEPTH STOP
ASSEMBLY
USING THE DEPTH STOP
See Figure 9.
When used, the depth stop limits the downward travel of
the blade when cutting dadoes and other non-through cuts.
To use the depth stop:
Remove the battery.
If the saw is in storage or transport position, unlock the
saw arm.
Rotate the depth stop away from the motor housing.
With the end of the depth control knob touching the depth
stop, adjust the depth control knob by turning the knob
until the desired depth of cut is attained.
A wooden spacer of at least 2 1/2 inches must be placed
between the workpiece and the fence for a consistent
depth of cut in the workpiece. Use the work clamp to
clamp the spacer and another suitable clamp to clamp
the workpiece. Make the slide cut at the desired depth.
See Figures 35 and 36.
Rotate the depth stop back towards the motor housing
for normal through cuts.
NOTE: The depth stop must be moved toward the motor
housing before locking/unlocking the saw arm.
LOCKING/UNLOCKING THE SAW ARM
See Figure 10.
When locking and unlocking the saw arm, it is not necessary
to loosen the depth control knob.
To unlock and raise the saw arm:
Firmly grasp the “D” handle and apply downward pres-
sure while at the same time pulling the lock pin out and
away from the saw housing.
Release the lock pin and slowly raise the saw arm.
To lock the saw arm:
Firmly grasp the “D” handle and apply downward pressure
while at the same time pushing the lock pin in and toward
the saw housing.
Release the lock pin allowing it to lock the saw into place.
15 − English
tooltip
DUST BAG
See Figure 11.
A dust bag is provided for use on this miter saw. It fits over
the exhaust port on the back of the saw.
NOTE: The exhaust port also accepts 1-1/4 in. vacuum hose.
BLADE WRENCH
See Figure 12.
A blade wrench is included with this saw. One end of the
wrench is a phillips screwdriver and the other end is a hex
key. Use the hex key end when installing or removing blade
and the Phillips end when removing or loosening screws. A
storage area for the blade wrench is located on the back of
the left miter fence.
WORK CLAMP
See Figure 12.
WARNING:
In some operations, the work clamp assembly may
interfere with the operation of the blade guard assembly.
Always make sure there is no interference with the blade
guard prior to beginning any cutting operation to reduce
the risk of serious personal injury.
The work clamp provides greater control by clamping the
workpiece to the fence or the saw table. It also prevents
the workpiece from creeping toward the saw blade. This is
very helpful when cutting compound miters. Depending on
the cutting operation and the size of the workpiece, it may
be necessary to use a C-clamp or other suitable clamp
instead of the work clamp to secure the workpiece prior to
making the cut.
To install the work clamp:
Place the work clamp shaft in one of the holes located
behind the miter fence.
Securely tighten the work clamp lock knob.
To adjust the work clamp:
Rotate the work clamp adjustment knob to adjust the
height of the clamp assembly up or down as needed to
secure the workpiece.
Rotate the work clamp knob until the clamp is firmly
pressed against the workpiece.
Fig. 12
BASE
WORK CLAMP
Fig. 11
DUST
BAG
EXHAUST
PORT
BLADE
WRENCH
WORK
CLAMP KNOB
ASSEMBLY
WORK CLAMP
LOCK KNOB
WORK CLAMP
ADJUSTMENT KNOB
16 − English
Fig. 13
BOLT HOLE
BOLT
BOLT
BASE
ASSEMBLY
TABLE EXTENSIONS
See Figures 13 - 15.
Table extensions have been provided for both the left and the
right side of the saw. The left and right extensions will only
fit properly one way. Be sure the front edge of the handle is
flush with the table.
To install table extensions:
Align the bolt to the bolt hole in the base.
Thread the bolt into the base. Use the blade wrench to
tighten the bolt.
NOTE: The left and right extension tables are different.
Be sure to check alignment to the front of the table before
installing bolts. Use a straight edge to check the exten-
sion table is level to the top of the base.
Repeat for other side.
Fig. 14
Fig. 15
LEFT TABLE
EXTENSION
RIGHT TABLE
EXTENSION
BASE
17 − English
ASSEMBLY
TO INSTALL/REPLACE THE BLADE
See Figures 16 - 17.
The blade is shipped installed on this miter saw model.
Instructions have been included for reference when chang-
ing or replacing blades.
WARNING:
A 10 in. blade is the maximum blade capacity of the saw.
Never use a blade that is too thick to allow outer blade
washer to engage with the flats on the spindle. Larger
blades will come in contact with the blade guards, while
thicker blades will prevent the blade bolt from securing
the blade on the spindle. Either of these situations could
result in a serious accident and can cause serious per-
sonal injury.
Remove the battery.
Raise saw arm.
Using the phillips screwdriver end of the blade wrench,
loosen, but do not remove, the blade bolt cover screw.
Rotate lower blade guard and blade bolt cover up and
back to expose the blade bolt.
Depress the spindle lock button and rotate the blade bolt
until the spindle locks.
Using the hex end of the blade wrench, loosen and remove
the blade bolt.
NOTE: The blade bolt has left hand threads. Turn blade
bolt clockwise to loosen.
Remove the outer blade washer. Do not remove the inner
blade washer.
Wipe a drop of oil onto inner blade washer and outer
blade washer where they contact the blade.
WARNING:
If inner blade washer has been removed, replace it before
placing blade on spindle. Failure to do so could cause an
accident since blade will not tighten properly.
Fit saw blade inside lower blade guard and onto spindle.
The blade teeth point downward at the front of saw as
shown in figure 17.
Replace the outer blade washer. The double “D” flats on
blade washers align with flats on spindle.
Depress spindle lock button and replace blade bolt.
NOTE: The blade bolt has left hand threads. Turn blade bolt
counterclockwise to tighten.
LOWER BLADE GUARD
OUTER BLADE
WASHER
WITH DOUBLE
“D” FLATS
BLADE
BOLT
FLAT(S)
ON SPINDLE
BLADE
BOLT COVER
BLADE
BOLT COVER
SCREW
NOTE: BEFORE USE,
ENSURE SCREW IS
TIGHTENED SECURELY
TO PREVENT GUARD
MOVEMENT
SPINDLE
LOCK BUTTON
TO
LOOSEN
TO
TIGHTEN
BLADE
INNER BLADE
WASHER WITH
DOUBLE “D”
FLATS
Fig. 16
Fig. 17
BLADE
BOLT
OUTER
BLADE
WASHER
BLADE
ARBOR
INNER
BLADE
WASHER
18 − English
CAUTION:
Always install the blade with the blade teeth and the arrow
printed on the side of the blade pointing down at the front
of the saw. The direction of blade rotation is also stamped
with an arrow on the upper blade guard.
Tighten blade bolt securely.
Replace blade bolt cover and tighten blade bolt cover-
screw securely.
Lower the blade guard.
Raise and lower the saw arm to ensure lower blade guard
functions correctly.
WARNING:
Make sure the spindle lock button is not engaged before
reconnecting saw into power source. Never engage
spindle lock button when blade is rotating.
REMOVING/REPLACING THE THROAT PLATE
See Figure 18.
WARNING:
The throat plate must be below the miter table. If the
throat plate is too high or too low, the workpiece can
catch on the uneven edges resulting in binding which
could result in serious personal injury.
Never operate the saw without a throat plate installed.
To remove/replace:
Remove the battery.
Remove the screws securing the throat plate.
Lift the throat plate from the saw.
To reinstall the throat plate, align the holes in the throat
plate with the holes in the saw base.
Retighten the screws, being careful not to overtighten
which can cause the throat plate to bow or bend.
ADJUSTING SUPPORT FOOT
See Figure 18.
Turn the support foot clockwise or counterclockwise depend-
ing on the amount of support needed for making sliding cuts.
NOTE: Many of the illustrations in this manual show only
portions of the compound miter saw. This is intentional so
that we can clearly show points being made in the illustra-
tions. Never operate the saw without all guards securely
in place and in good operating condition.
THROAT
PLATE
Fig. 18
SUPPORT
FOOT
ASSEMBLY
19 − English
Fig. 19
MITER
LOCK HANDLE
MITER
TABLE
MITER
TABLE
MITER
TABLE
VIEW OF BLADE SQUARE WITH FENCE
SQUARE
SQUARE
SQUARE
MITER
FENCE
MITER
FENCE
MITER
FENCE
BLADE
BLADE
BLADE
SQUARING THE BLADE TO THE FENCE
See Figures 19 - 24.
Remove the battery.
Pull the saw arm all the way down and engage the lock
pin to hold the saw arm in transport position.
Loosen the miter lock handle approximately one-half turn
and squeeze the detent release lever.
Rotate the control arm until the scale indicator is posi-
tioned at 0°.
Release the detent release lever, engaging the positive
stop notch, then tighten the miter lock knob to secure
the miter table.
Loosen bevel lock knob and set saw arm at 0° bevel
(blade set 90° to miter table). Tighten bevel lock knob.
Lay a square flat on the miter table. Place one leg of the
square against the fence. Slide the other leg of the square
against the flat part of saw blade.
NOTE: Make sure that the square contacts the flat part
of the saw blade, not the blade teeth.
The edge of the square and the saw blade should be
parallel as shown in figure 19.
If the front or back edge of the saw blade angles away
from the square as shown in figures 20 and 21, adjust-
ments are needed.
ASSEMBLY
VIEW OF BLADE NOT SQUARE WITH
FENCE, ADJUSTMENTS ARE REQUIRED
Fig. 20
Fig. 21
VIEW OF BLADE NOT SQUARE WITH
FENCE, ADJUSTMENTS ARE REQUIRED
20 − English
BEVEL
LOCK KNOB
Fig. 23
Fig. 24
SCALE
INDICATOR
INDICATOR
SCREW
MITER SCALE
Loosen the fence screw and slide the partial sliding miter
fence toward the blade to access the socket head screws
securing the left miter fence to the table.
Using the blade wrench provided, loosen the socket head
screws that secure the miter fence to the miter table.
Rotate the miter fence left or right until the saw blade is
parallel with the square.
Retighten the screws securely and recheck the blade-to-
fence alignment.
Return the partial sliding miter fence to the home position
and retighten the fence screw to secure.
Your saw has several scale indicators. After squaring adjust-
ments have been made, it may be necessary to loosen the
indicator screws and reset them to zero. See Figures 23 - 24.
ASSEMBLY
SOCKET HEAD
SCREW(S)
MITER
FENCE
SOCKET HEAD
SCREW(S)
Fig. 22
FENCE
SCREW
PARTIAL
SLIDING
MITER
FENCE
BEVEL
SCALE
SCALE
INDICATOR INDICATOR
SCREW
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Ryobi PBLMS01B Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire
Ce manuel convient également à