Ryobi PBLMS01B Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

10 in. 18V SLIDING COMPOUND

MITER SAW WITH LED

SCIE À ONGLETS COMBINÉS

COULISSANTE DE 254 mm (10 po)

DE18V AVECDEL

SIERRA INGLETEADORA COMPUESTA

DESLIZANTE DE 254 mm (10 pulg.)

DE18V CONLED

PBLMS01

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

AVERTISSEMENT :

Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

TABLE OF CONTENTS

****************

 General Safety Rules ...................... 2-3

 Miter Saw Speciﬁc Safety Rules ........4

 Additional Safety Rules ......................5

 Symbols ..............................................6

 Glossary of Terms ...............................7

 Features ........................................ 8-10

 Tools Needed ...................................11

 Loose Parts List ................................11

 Assembly .................................... 12-21

 Operation .................................... 22-31

 Adjustments .....................................32

 Maintenance ............................... 33-34

 Parts Ordering / Service ..... Back Page

TABLE DES MATIÈRES

****************

 Règles de sécurité générales ......... 2-3

 Règles de sécurité scie à onglets ... 3-4

 Règles de sécurité supplémentaires .......5

 Symboles ............................................6

 Glossaire .............................................7

 Caractéristiques ........................... 8-10

 Outils nécessaires ............................11

 Liste des pièces détachées ..............11

 Assemblage ................................ 12-21

 Utilisation .................................... 22-32

 Réglages ...........................................33

 Entretien ...........................................34

 Commande de pièces /

réparation ..........................Page arrière

ÍNDICE DE CONTENIDO

****************

 Reglas de seguridad generales ...... 2-3

 Reglas de seguridad sierra

ingleteadora ................................... 3-4

 Advertencias de seguridad

adicionales .........................................5

 Símbolos ............................................6

 Glosario de términos ..........................7

 Características.............................. 8-10

 Herramientas necesarias ..................11

 Lista de piezas sueltas .....................11

 Armado ....................................... 12-21

 Funcionamiento .......................... 22-32

 Ajustes ..............................................33

 Mantenimiento ..................................34

 Pedidos de piezas /

servicio .......................... Pág. posterior

2 − English

GENERAL SAFETY RULES

WARNING:

Read all safety warnings, instructions, illustrations

and speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may result

in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

 Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

 Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

 Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

 Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodiﬁed plugs and

matching outlets will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

 Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

 Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

 When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is un-

avoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of

electric shock.

PERSONAL SAFETY

 Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use

a power tool while you are tired or under the inﬂuence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

 Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

 Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the switch or

energising power tools that have the switch on invites

accidents.

 Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

 Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

 Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

 If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

 Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

POWER TOOL USE AND CARE

 Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

 Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

 Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

 Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

3 − English

GENERAL SAFETY RULES

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

 Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

 Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

BATTERY TOOL USE AND CARE

 Recharge only with the charger speciﬁed by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of ﬁre when used with

another battery pack.

 Use power tools only with speciﬁcally designated bat-

tery packs. Use of any other battery packs may create

a risk of injury and ﬁre.

 When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a ﬁre.

 Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ﬂush with water. If liquid contacts eyes, ad-

ditionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

 Do not use a battery pack or tool that is damaged or

modiﬁed. Damaged or modiﬁed batteries may exhibit

unpredictable behavior resulting in ﬁre, explosion, or risk

of injury.

 Do not expose a battery pack or tool to ﬁre or exces-

sive temperature. Exposure to ﬁre or temperature above

265° F may cause explosion.

 Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

speciﬁed in the instructions. Charging improperly or at

temperatures outside the speciﬁed range may damage

the battery and increase the risk of ﬁre.

 Use battery only with charger listed. For use with 18V

lithium-ion battery packs, see tool/appliance/battery pack/

charger correlation supplement 987000-432.

 Battery tools do not have to be plugged into an elec-

trical outlet; therefore, they are always in operating

condition. Be aware of possible hazards when not

using your battery tool or when changing accessories.

Following this rule will reduce the risk of electric shock,

ﬁre, or serious personal injury.

 Do not place battery tools or their batteries near ﬁre

or heat. This will reduce the risk of explosion and pos-

sibly injury.

 Do not crush, drop or damage battery pack. Do not

use a battery pack or charger that has been dropped

or received a sharp blow. A damaged battery is subject

to explosion. Properly dispose of a dropped or damaged

battery immediately.

 Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open ﬂame. An exploded battery can

propel debris and chemicals. If exposed, ﬂush with water

immediately.

 Do not charge battery tool in a damp or wet location.

Do not use, store, or charge battery packs or products

in locations where the temperature is less than 50°F

or more than 100°F. Do not store outside or in vehicles.

 Under extreme usage or temperature conditions, bat-

tery leakage may occur. If liquid comes in contact with

your skin, wash immediately with soap and water. If

liquid gets into your eyes, ﬂush them with clean water

for at least 10 minutes, then seek immediate medical

attention. Following this rule will reduce the risk of seri-

ous personal injury.

SERVICE

 Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

 Never service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

4 − English

MITER SAW SPECIFIC SAFETY RULES

Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

Use clamps to support the workpiece whenever pos-

sible. If supporting the workpiece by hand, you must

always keep your hand at least 100 mm from either

side of the saw blade. Do not use this saw to cut pieces

that are too small to be securely clamped or held by

hand. If your hand is placed too close to the saw blade,

there is an increased risk of injury from blade contact.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut ”freehand” in

any way. Unrestrained or moving workpieces could be

thrown at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down

and push the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to climb

on top of the workpiece and violently throw the blade

assembly towards the operator.

Never cross your hand over the intended line of cutting

either in front or behind the saw blade. Supporting the

workpiece ”cross handed” i.e. holding the workpiece

to the right of the saw blade with your left hand or vice

versa is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the workpiece

is bowed or warped, clamp it with the outside bowed

face toward the fence. Always make certain that there

is no gap between the workpiece, fence and table

along the line of the cut. Bent or warped workpieces can

twist or shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or foreign

objects in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that con-

tact the revolving blade can be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

Ensure the miter saw is mounted or placed on a

level, ﬁrm work surface before use. A level and ﬁrm

work surface reduces the risk of the miter saw becoming

unstable.

Plan your work. Every time you change the bevel or

miter angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool ”ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

miter saw table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling

you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If conﬁned,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

Always use a clamp or a ﬁxture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

If the workpiece or blade becomes jammed, turn the

miter saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or re-

move the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the miter saw.

After ﬁnishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Hold the handle ﬁrmly when making an incomplete

cut or when releasing the switch before the saw head

is completely in the down position. The braking action

of the saw may to be suddenly pulled downward, causing

a risk of injury.

 Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

5 − English

ADDITIONAL SAFETY RULES

 Inspect tool cords periodically. If damaged, have re-

paired by a qualiﬁed service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 Inspect extension cords periodically and replace if

damaged.

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than

the other). This plug will ﬁt in a polarized outlet only one

way. If the plug does not ﬁt fully in the outlet, reverse the

plug. If it still does not ﬁt, contact a qualiﬁed electrician

to install the proper outlet. Do not change the plug in any

way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the speciﬁc potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ANSI Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with incorrect

size holes. Never use blade washers or blade bolts that

are defective or incorrect. The maximum blade capacity

of your saw is 10 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight and

not making contact with saw or workpiece before con-

necting to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel func-

tion) are locked in position before operating your saw.

Lock the miter table by pushing the miter lock lever down.

Lock the saw arm (bevel function) by securely tightening

the bevel lock knob.

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the ﬂoor or in a crouched

position.

 Never stand or have any part of the body in line with the

path of the saw blade.

 Do not turn the motor switch on and off rapidly. This

could cause the saw blade to loosen and could create

a hazard. Should this ever occur, stand clear and allow

the saw blade to come to a complete stop. Disconnect

your saw from the power supply and securely retighten

the blade bolt.

 If any part of this miter saw is missing or should break,

bend, or fail in any way, or should any electrical compo-

nent fail to perform properly, shut off the power switch,

remove the miter saw plug from the power source and

have damaged, missing, or failed parts replaced before

resuming operation.

 Always turn off the saw before disconnecting it to avoid

accidental starting when reconnecting to power supply.

NEVER leave the saw unattended while connected to a

power source.

 This tool should have the following markings:

• To reduce the risk of injury, user must read the opera-

tor’s manual.

• Wear eye protection.

• Keep hands and body out of the path of the saw blade.

Contact with the blade will result in serious injury.

• Check guarding system to make sure it is functioning

correctly.

• Do not perform any operation freehand.

• Never reach around the saw blade.

• Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

• Disconnect the saw from the power source before

changing blade or servicing.

 Always carry the tool only by the carrying handle.

 This saw can tip over if the saw head is released sud-

denly and the saw is not secured to a work surface. Always

secure this saw to a stable work surface before any use

to avoid serious personal injury.

 Always make sure the saw blade has clearance of

all obstructions before turning the saw on.

6 − English

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-

tion of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye Protection Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

No Hands Symbol Failure to keep your hands away from the blade will result in seri-

ous personal injury.

Extremely Bright Light This product uses extremely bright LEDs. To avoid serious eye

injury, do not stare into the light (not even from a distance).

Wet Conditions Alert Do not expose to rain or use in damp locations.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

7 − English

GLOSSARY OF TERMS

Pilot Hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick (not

a push block). A push block can be used for narrow ripping

operations, if a jig or similar cutting aid is used. These aids

help keep the operator’s hands well away from the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper Cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a cutting,

drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the miter gauge groove.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-Through Cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

8 − English

FEATURES

PRODUCT SPECIFICATIONS

Arbor Hole ................................................................. 5/8 in.

Blade Diameter ............................................................10 in.

No Load Speed ........................................4,100/min. (RPM)

Input ................................................................... 18 Volt DC

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum lumber sizes .......................... 1-1/2 in. x 12 in.

or 3-1/2 in. x 5-1/2 in.

Cutting Capacity with Miter at 45°/Bevel 0°:

Maximum lumber sizes ......................1-1/2 in. x 7-1/4 in.

Cutting Capacity with Miter at 0°/Bevel 45°:

Maximum lumber sizes .......................... 1-1/2 in. x 12 in.

Cutting Capacity with Miter at 45°/Bevel 45°:

Maximum lumber sizes ......................1-1/2 in. x 7-1/4 in.

Fig. 1

BEVEL

SCALE

BEVEL

LOCK KNOB

DEPTH

CONTROL KNOB

DEPTH STOP

LOCK

SWITCH

TRIGGER

DUST BAG

MITER

FENCE

TABLE

EXTENSION BASE

WORK

CLAMP

MITER

TABLE

CONTROL

ARM

MITER

LOCK HANDLE

“NO HANDS

ZONE” LABEL

“NO HANDS ZONE”

BOUNDARY LINE

MITER

SCALE

UPPER BLADE

GUARD

LOWER BLADE

GUARD

“D”

HANDLE

SLIDE

LOCK KNOB

SLIDE BAR

SUPPORT FOOT

POSITIVE

STOP(S) DETENT RELEASE LEVER

BLADE

WRENCH

THROAT

PLATE

LED

SWITCH

PARTIAL SLIDING

FENCE

CARRYING

HANDLE

9 − English

FEATURES

KNOW YOUR COMPOUND MITER SAW

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

10 IN. BLADE

A 10 in. blade is included with the compound miter saw. It will

cut materials up to 3-1/2 in. thick or 12 in. wide, depending

upon the angle at which the cut is being made.

BEVEL LOCK KNOB

See Figure 2.

The bevel lock knob securely locks your compound miter saw

at desired bevel angles. A positive stop adjustment screw has

been provided on each side of the saw arm. These adjust-

ment screws are for making ﬁne adjustments at 0° and 45°.

CARRYING HANDLE

See Figure 2.

For convenience when carrying or transporting the miter

saw from one place to another, a carrying handle has been

provided on top of the saw arm. To transport, turn off the saw

and remove the battery, then lower the saw arm and lock it in

the down position by pushing in the lock pin.

NOTE: DO NOT perform any cutting operation with the saw

in the locked position.

DETENT OVERRIDE

See Figure 3.

The detent override allows the miter table to move freely to

any desired angle. With the miter lock handle loosened and the

detent release lever squeezed (1), pull the detent override up (2)

and release the detent release lever (3) to bypass the positive

stops on the miter scale. To release the detent override and

allow the miter table to engage the positive stops, squeeze

and release the detent release lever.

ELECTRIC BRAKE

An electric brake has been provided to quickly stop blade

rotation after the switch is released.

LED LIGHTING SYSTEM

The LED casts a shadow of the blade teeth onto the workpiece

for making precision cuts and predicts blade kerf for blade

cut line.

MITER FENCE

The miter fence on the compound miter saw has been pro-

vided to hold your workpiece securely against when making

all cuts. The right side is larger providing additional support.

MITER LOCK HANDLE

See Figure 3.

The miter lock handle securely locks the saw at desired miter

angles. Tighten the handle to lock the saw in place. To release

the saw, loosen the handle and squeeze the detent release lever.

SAW ARM LOCKED IN DOWN POSITION

LOCK

CARRYING

HANDLE

“D”

HANDLE

MITER

LOCK HANDLE

BEVEL

LOCK KNOB

LED GUIDE

SWITCH

Fig. 2

Fig. 3

1

3

2

DETENT

RELEASE LEVER

DETENT

OVERRIDE

10 − English

SPINDLE

LOCK BUTTON

FEATURES

MITER SCALE

The miter scale has index points provided at 0°, 15°, 22.5°,

30, 31.6°, and 45°.

PARTIAL SLIDING FENCE

The partial sliding fence on your compound miter saw has

been provided to help secure the workpiece when making

straight cuts.

The sliding feature makes it easy to adjust the position of the

partial fence. Loosen the fence screw before attempting to

slide the partial fence. Once the desired position is determined,

tighten the fence screw to secure.

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 15°, 22.5°, 31.6°, and

45° on both the left and right side of the miter table.

NOTE: To bypass the positive stops, squeeze the detent

release lever and lift the detent override. To release the over-

ride, squeeze the detent release lever.

SELF-RETRACTING LOWER BLADE GUARD

The lower blade guard is made of shock-resistant, see-through

plastic that provides protection from each side of the blade.

It retracts over the upper blade guard as the saw is lowered

into the workpiece.

SLIDE BARS

When unlocked, the saw arm will glide forward and backward

the length of the slide bars for cutting various workpiece widths.

SLIDE LOCK KNOB

The slide lock knob locks and unlocks the sliding feature of

this tool.

SPINDLE LOCK BUTTON

See Figure 4.

The spindle lock button locks the spindle and stops the blade

from rotating. Depress and hold the lock button while install-

ing, changing, or removing blade.

SWITCH TRIGGER

See Figure 4.

The saw will not start until you depress the trigger lockout

lever and squeeze the switch trigger. To prevent unauthor-

ized use of the compound miter saw, disconnect it from the

power supply and lock the switch in the OFF position. To lock

the switch, install a padlock (not included) through the hole

in the switch trigger and make certain the switch is inoper-

able. If the switch is still operable with the padlock installed,

a padlock with a larger shackle diameter must be used. Store

the padlock key in another location.

Fig. 4

PADLOCK SWITCH

TRIGGER

SWITCH

TRIGGER

PADLOCK

HOLE

11 − English

LOOSE PARTS LIST

Fig. 6

 Table Extensions (2)

 Work Clamp

 Operator’s Manual (not shown)

 Blade Wrench

 Carrying Handle

 Dust Bag

WORK

CLAMP

DUST BAG

RIGHT TABLE

EXTENSION

LEFT TABLE

EXTENSION

The following items are included with the tool:

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

The following tools (not included) are needed for making adjustments or installing the blade:

TOOLS NEEDED

Fig. 5

COMBINATION

SQUARE

BLADE

WRENCH

CARRYING

HANDLE

12 − English

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this tool. Any such

alteration or modiﬁcation is misuse and could result in a

hazardous condition leading to possible serious personal

injury.

WARNING:

Do not connect to power supply until assembly is com-

plete. Failure to comply could result in accidental starting

and possible serious personal injury.

WARNING:

Do not start the compound miter saw without checking

for interference between the blade and the miter fence.

Serious personal injury or damage to the blade could

result if it strikes the miter fence during operation of the

saw.

WARNING:

This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. ALWAYS

secure this saw to a stable work surface before any use

to avoid serious personal injury.

UNPACKING

This product requires assembly.

 Carefully lift saw from the carton by the carrying handle

and the saw base, and place it on a level work surface.

WARNING:

Do not use this product if any parts on the

Loose Parts

List

are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 This saw has been shipped with the saw arm secured in

the down position. To release the saw arm, push down

on the “D” handle, cut the tie-wrap, and pull out on the

lock pin.

WARNING:

The saw arm is spring loaded. Hold the handle down to

prevent it from snapping up when cutting the tie-wrap.

Failure to do so could result in possible serious injury.

 Lift the saw arm by the “D” handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon release

of the tie wrap.

 Cut the tie wrap at the end of the slide bar. Slide the saw

head to its most rearward position and tighten the slide

lock knob securely.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 The saw is factory set for accurate cutting. After assem-

bling it, check for accuracy. If shipping has inﬂuenced

the settings, refer to speciﬁc procedures explained in

this manual.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

ASSEMBLY

13 − English

Fig. 8

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

Fig. 7

MOUNTING

SURFACE

SAW BASE

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

MOUNTING HOLES

See Figure 7.

WARNING:

Before starting any cutting operation, clamp or bolt

your miter saw to a workbench or an approved miter

saw stand. If a miter saw stand is used, read operator’s

manual and follow the instructions for the miter saw

stand. Never operate your miter saw on the ﬂoor or in a

crouched position. Failure to heed this warning can result

in serious personal injury.

The compound miter saw should be mounted to a ﬁrm sup-

porting surface such as a workbench, mounting board, or

miter saw stand. The saw base has four mounting holes. If

using bolts or screws, they should be of sufﬁcient length to

accommodate the saw base, lock washers, hex nuts, and

the thickness of the workbench or other mounting surface.

Tighten all bolts or screws securely.

The hole pattern for mounting to a workbench is shown in

ﬁgure 7. Carefully check the workbench after mounting to

make sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the workbench

to the ﬂoor before operating.

INSTALL THE CARRYING HANDLE

See Figure 8.

 Remove the battery.

 Align the handle over the tabs on the top of the saw.

 Insert the lock nuts into the pockets.

NOTE: Hold the two lock nuts in place with ﬁngers while

tightening the bolts. Make sure the nylock is to the outside

of the bolt for easier threading.

 Insert the bolts through the handle and tabs.

 Thread the bolts into the lock nuts.

 Tighten the bolts using the blade wrench.

LOCK NUTS

BOLTS

TABS

CARRYING

HANDLE

ASSEMBLY

14 − English

Fig. 10

LOCK

“D”

HANDLE

Fig. 9

DEPTH

CONTROL KNOB

DEPTH STOP

ASSEMBLY

USING THE DEPTH STOP

See Figure 9.

When used, the depth stop limits the downward travel of

the blade when cutting dadoes and other non-through cuts.

To use the depth stop:

 Remove the battery.

 If the saw is in storage or transport position, unlock the

saw arm.

 Rotate the depth stop away from the motor housing.

 With the end of the depth control knob touching the depth

stop, adjust the depth control knob by turning the knob

until the desired depth of cut is attained.

 A wooden spacer of at least 2 1/2 inches must be placed

between the workpiece and the fence for a consistent

depth of cut in the workpiece. Use the work clamp to

clamp the spacer and another suitable clamp to clamp

the workpiece. Make the slide cut at the desired depth.

See Figures 35 and 36.

 Rotate the depth stop back towards the motor housing

for normal through cuts.

NOTE: The depth stop must be moved toward the motor

housing before locking/unlocking the saw arm.

LOCKING/UNLOCKING THE SAW ARM

See Figure 10.

When locking and unlocking the saw arm, it is not necessary

to loosen the depth control knob.

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward pres-

sure while at the same time pulling the lock pin out and

away from the saw housing.

 Release the lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward pressure

while at the same time pushing the lock pin in and toward

the saw housing.

 Release the lock pin allowing it to lock the saw into place.

15 − English

tooltip

DUST BAG

See Figure 11.

A dust bag is provided for use on this miter saw. It ﬁts over

the exhaust port on the back of the saw.

NOTE: The exhaust port also accepts 1-1/4 in. vacuum hose.

BLADE WRENCH

See Figure 12.

A blade wrench is included with this saw. One end of the

wrench is a phillips screwdriver and the other end is a hex

key. Use the hex key end when installing or removing blade

and the Phillips end when removing or loosening screws. A

storage area for the blade wrench is located on the back of

the left miter fence.

WORK CLAMP

See Figure 12.

WARNING:

In some operations, the work clamp assembly may

interfere with the operation of the blade guard assembly.

Always make sure there is no interference with the blade

guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

The work clamp provides greater control by clamping the

workpiece to the fence or the saw table. It also prevents

the workpiece from creeping toward the saw blade. This is

very helpful when cutting compound miters. Depending on

the cutting operation and the size of the workpiece, it may

be necessary to use a C-clamp or other suitable clamp

instead of the work clamp to secure the workpiece prior to

making the cut.

To install the work clamp:

 Place the work clamp shaft in one of the holes located

behind the miter fence.

 Securely tighten the work clamp lock knob.

To adjust the work clamp:

 Rotate the work clamp adjustment knob to adjust the

height of the clamp assembly up or down as needed to

secure the workpiece.

 Rotate the work clamp knob until the clamp is ﬁrmly

pressed against the workpiece.

Fig. 12

BASE

WORK CLAMP

Fig. 11

DUST

BAG

EXHAUST

PORT

BLADE

WRENCH

WORK

CLAMP KNOB

ASSEMBLY

WORK CLAMP

LOCK KNOB

WORK CLAMP

ADJUSTMENT KNOB

16 − English

Fig. 13

BOLT HOLE

BOLT

BASE

ASSEMBLY

TABLE EXTENSIONS

See Figures 13 - 15.

Table extensions have been provided for both the left and the

right side of the saw. The left and right extensions will only

ﬁt properly one way. Be sure the front edge of the handle is

ﬂush with the table.

To install table extensions:

 Align the bolt to the bolt hole in the base.

 Thread the bolt into the base. Use the blade wrench to

tighten the bolt.

NOTE: The left and right extension tables are different.

Be sure to check alignment to the front of the table before

installing bolts. Use a straight edge to check the exten-

sion table is level to the top of the base.

 Repeat for other side.

Fig. 14

Fig. 15

LEFT TABLE

EXTENSION

RIGHT TABLE

EXTENSION

BASE

17 − English

ASSEMBLY

TO INSTALL/REPLACE THE BLADE

See Figures 16 - 17.

The blade is shipped installed on this miter saw model.

Instructions have been included for reference when chang-

ing or replacing blades.

WARNING:

A 10 in. blade is the maximum blade capacity of the saw.

Never use a blade that is too thick to allow outer blade

washer to engage with the ﬂats on the spindle. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from securing

the blade on the spindle. Either of these situations could

result in a serious accident and can cause serious per-

sonal injury.

 Remove the battery.

 Raise saw arm.

 Using the phillips screwdriver end of the blade wrench,

loosen, but do not remove, the blade bolt cover screw.

Rotate lower blade guard and blade bolt cover up and

back to expose the blade bolt.

 Depress the spindle lock button and rotate the blade bolt

until the spindle locks.

 Using the hex end of the blade wrench, loosen and remove

the blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

 Remove the outer blade washer. Do not remove the inner

blade washer.

 Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before

placing blade on spindle. Failure to do so could cause an

accident since blade will not tighten properly.

 Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in ﬁgure 17.

 Replace the outer blade washer. The double “D” ﬂats on

blade washers align with ﬂats on spindle.

 Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt

counterclockwise to tighten.

LOWER BLADE GUARD

OUTER BLADE

WASHER

WITH DOUBLE

“D” FLATS

BLADE

BOLT

FLAT(S)

ON SPINDLE

BLADE

BOLT COVER

BLADE

BOLT COVER

SCREW

NOTE: BEFORE USE,

ENSURE SCREW IS

TIGHTENED SECURELY

TO PREVENT GUARD

MOVEMENT

SPINDLE

LOCK BUTTON

TO

LOOSEN

TO

TIGHTEN

BLADE

INNER BLADE

WASHER WITH

DOUBLE “D”

FLATS

Fig. 16

Fig. 17

BLADE

BOLT

OUTER

BLADE

WASHER

BLADE

ARBOR

INNER

BLADE

WASHER

18 − English

CAUTION:

Always install the blade with the blade teeth and the arrow

printed on the side of the blade pointing down at the front

of the saw. The direction of blade rotation is also stamped

with an arrow on the upper blade guard.

 Tighten blade bolt securely.

 Replace blade bolt cover and tighten blade bolt cover-

screw securely.

 Lower the blade guard.

 Raise and lower the saw arm to ensure lower blade guard

functions correctly.

WARNING:

Make sure the spindle lock button is not engaged before

reconnecting saw into power source. Never engage

spindle lock button when blade is rotating.

REMOVING/REPLACING THE THROAT PLATE

See Figure 18.

WARNING:

The throat plate must be below the miter table. If the

throat plate is too high or too low, the workpiece can

catch on the uneven edges resulting in binding which

could result in serious personal injury.

Never operate the saw without a throat plate installed.

To remove/replace:

 Remove the battery.

 Remove the screws securing the throat plate.

 Lift the throat plate from the saw.

 To reinstall the throat plate, align the holes in the throat

plate with the holes in the saw base.

 Retighten the screws, being careful not to overtighten

which can cause the throat plate to bow or bend.

ADJUSTING SUPPORT FOOT

See Figure 18.

Turn the support foot clockwise or counterclockwise depend-

ing on the amount of support needed for making sliding cuts.

NOTE: Many of the illustrations in this manual show only

portions of the compound miter saw. This is intentional so

that we can clearly show points being made in the illustra-

tions. Never operate the saw without all guards securely

in place and in good operating condition.

THROAT

PLATE

Fig. 18

SUPPORT

FOOT

ASSEMBLY

19 − English

Fig. 19

MITER

LOCK HANDLE

MITER

TABLE

MITER

TABLE

MITER

TABLE

VIEW OF BLADE SQUARE WITH FENCE

SQUARE

MITER

FENCE

MITER

FENCE

MITER

FENCE

BLADE

SQUARING THE BLADE TO THE FENCE

See Figures 19 - 24.

 Remove the battery.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn

and squeeze the detent release lever.

 Rotate the control arm until the scale indicator is posi-

tioned at 0°.

 Release the detent release lever, engaging the positive

stop notch, then tighten the miter lock knob to secure

the miter table.

 Loosen bevel lock knob and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock knob.

 Lay a square ﬂat on the miter table. Place one leg of the

square against the fence. Slide the other leg of the square

against the ﬂat part of saw blade.

NOTE: Make sure that the square contacts the ﬂat part

of the saw blade, not the blade teeth.

 The edge of the square and the saw blade should be

parallel as shown in ﬁgure 19.

 If the front or back edge of the saw blade angles away

from the square as shown in ﬁgures 20 and 21, adjust-

ments are needed.

ASSEMBLY

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 20

Fig. 21

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

20 − English

BEVEL

LOCK KNOB

Fig. 23

Fig. 24

SCALE

INDICATOR

SCREW

MITER SCALE

 Loosen the fence screw and slide the partial sliding miter

fence toward the blade to access the socket head screws

securing the left miter fence to the table.

 Using the blade wrench provided, loosen the socket head

screws that secure the miter fence to the miter table.

 Rotate the miter fence left or right until the saw blade is

parallel with the square.

 Retighten the screws securely and recheck the blade-to-

fence alignment.

 Return the partial sliding miter fence to the home position

and retighten the fence screw to secure.

Your saw has several scale indicators. After squaring adjust-

ments have been made, it may be necessary to loosen the

indicator screws and reset them to zero. See Figures 23 - 24.

ASSEMBLY

SOCKET HEAD

SCREW(S)

MITER

FENCE

SOCKET HEAD

SCREW(S)

Fig. 22

FENCE

SCREW

PARTIAL

SLIDING

MITER

FENCE

BEVEL

SCALE

INDICATOR INDICATOR

SCREW

La page charge ...

Ryobi PBLMS01B Le manuel du propriétaire

Ce manuel convient également à

Ryobi PBLMS01B Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents