VTech Digital Audio Monitor Manuel utilisateur

Marque: VTech

Modèle: Digital Audio Monitor

Catégorie: Babyphones

Taper: Manuel utilisateur

Ce manuel convient également à

DM223

Caution

• The default volume of your parent unit is level 3. If you experience high-pitched screeching noise from

your baby monitor while positioning:

- Make sure your baby unit and parent unit are more than 6.5 feet (2 meters) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to 1,000 feet (300 meters) outdoors. The actual

operating range may vary depending on the environmental conditions, and other interferences

such as walls, doors, and other obstructions.

Install the parent unit battery

The parent unit runs on rechargeable battery or AC power. To continuously monitor your

baby, keep the parent unit connected to AC power. With the battery alone, the parent unit

can cordlessly run for a short time only.

NOTESNOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.

Replace the battery

To replace the battery, unplug the battery connector from the socket, and then pull the

battery out of the battery compartment. Follow the steps above to install the battery.

Connect the baby monitor

NOTESNOTE

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to an electric outlet that is controlled by a switch.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

• With audio reminder feature preset to ON, the parent unit plays an audio reminder when it is

connected to a baby unit.

Charge the parent unit battery

When you have connected the parent unit and installed its battery for the ﬁrst time or after

power outage, the parent unit powers on automatically. The battery icon indicates the

battery status (see the following table).

1 set for DM223;

2 sets for DM223-2

User’s manual

DM223

DM223-2

Digital Audio Monitor

Go to www.vtechphones.com

to register your product for enhanced

warranty support and the latest VTech

product news.

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety

instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

What’s in the box

Connect and charge the battery

NOTESNOTE

Notes

• The parent unit battery is fully charged after 11 hours of continuous charging.

• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,

turn the parent unit off while charging.

• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

Battery indicators Battery status Action

The battery icon is off. No battery is installed but

operates using AC power.

-OR-

Abnormal battery is detected.

Install the parent unit battery.

Charge without interruption (at

least 30 minutes).

The screen displays LOW

BATTERY and . The light

flashes.

The battery has very little

charge and may be used for

only a short time.

Charge

without interruption

(about 30 minutes).

The battery icon becomes

solid .

The battery is fully charged. To keep the battery charged,

connect it to AC power when not

in use.

NOTESNOTE

Note

Make sure the label

THIS SIDE UP is facing

up while inserting the

battery.

Note

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and

should not be used as such.

Test your audio monitor

You may test the baby monitor before initial use, and at regular times thereafter.

Caution

• For hearing protection, make sure the parent unit is more than

6.5 feet (2 meters) away from the baby unit. If you hear any

high-pitched noise, move the parent unit further until the noise

stops. You can also press VOL. on the parent unit to lower or

mute the noise.

1. Make sure your baby unit and parent unit are on.

2. Speak towards the microphone of the baby unit. You will

hear the sound at the parent unit, and see the visual sound

indicators light up.

Note

• When the parent unit displays NOT LINKED and ﬂashes, move the parent unit closer to the baby unit

(observe the minimum distance of 6.5 feet/ 2 meters).

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the

baby unit.

Positioning the baby monitor

Caution

• Keep the baby units out of the reach of your baby. Never place or mount the baby units inside the

baby’s crib or playpen.

1. Place the baby units more than 3 feet (1 meter) away from your baby.

2. Place the parent unit more than 6.5 feet (2 meters) away from the baby unit.

Before use

3 Using the baby monitor

Power on or off the baby unit

• Press POWER to power on the baby unit. The power light turns on.

• Press and hold POWER to power off the baby unit. The power

light turns off.

Power on or off the parent unit

• Press and hold to power on the parent unit. The screen turns on.

• Press and hold again to power off the parent unit. The screen

turns off.

Note

• The parent unit powers on automatically once it is connected to power

socket or battery installed. The baby unit also powers on automatically once

connected to power socket.

Adjust the speaker volume for baby unit

• Press VOL. or VOL. on the baby unit at any time.

Note

• The speaker of baby unit cannot be muted.

Adjust the speaker volume for parent unit

You can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The speaker

volume is preset to VOLUME 3.

• Press VOL. or VOL. when the parent unit is not in use.

When the speaker volume is set to VOLUME OFF, the screen displays .

Adjust the sound sensitivity of the baby unit

You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for

transmitting to the parent unit. The VOX sensitivity level is preset to HIGHEST.

VOX

Sensitivity

level

Highest High Medium Low Lowest

Description The parent

unit speaker

is constantly

on, and you

will hear

all sounds

(including

background

noises) from

your baby’s

room.

The parent

unit speaker

turns on for

soft babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby sleeps

soundly.

The parent

unit speaker

turns on

for loud

babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent

unit speaker

turns on

for crying

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent

unit speaker

turns on for

loud crying

or screeching

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

1. Press MENU/ when the parent unit is not in use.

2. Press SELECT to select VOX LEVEL.

3. Press VOL. or VOL. to choose the desired sensitivity level.

4. Press SELECT to conﬁrm your selection. The screen displays SAVED and you hear a

conﬁrmation tone.

Note

• To enter the VOX Level menu of the parent unit, the baby unit must be turned on.

Sound alert

If you want the parent unit alerts you with sound, especially when the baby unit detects loud

sounds, you can turn on the sound alert feature. This feature is preset to OFF.

Once this feature is on, is shown on LCD display. When the visual sound indicator hits the

red light range, i.e. the baby unit detects loud sounds, your parent unit beeps and flashes.

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose SOUND ALERT, then press SELECT.

3. Press VOL. or VOL. to choose ON or OFF.

4. Press SELECT to conﬁrm your selection. The screen displays SAVED and you hear a

conﬁrmation tone.

Note

• The sound alert setting on each parent unit is independent.

Vibration alert

You can set your parent unit to vibrate and alert you, whenever the baby unit detects loud

sounds. This feature is preset to OFF.

Once this feature is on, is shown on LCD display. When the visual sound indicator hits the red

light range, i.e. the baby unit detects loud sounds, your parent unit vibrates and flashes.

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose VIBE ALERT, then press SELECT.

3. Press VOL. or VOL. to choose ON or OFF.

4. Press SELECT to conﬁrm your selection. The screen displays SAVED and you hear a

conﬁrmation tone.

Notes

• Each time you set the vibration alert to ON, the parent unit vibrates brieﬂy after you press SELECT.

• The vibration alert setting on each parent unit is independent.

Nightlight

Both your parent unit(s) and baby unit allow you to turn on or off the nighlight on the baby unit.

Turn on/off the nightlight using the baby unit:

1. Press NIGHT LIGHT to turn on the nightlight.

2. Press NIGHT LIGHT again to turn off the nightlight.

Turn on/off the nightlight using the parent unit:

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose NIGHTLIGHT, then press SELECT.

3. Press VOL. or VOL. to choose ON or OFF.

4. Press SELECT to conﬁrm your selection. The screen displays SAVED and you hear

a conﬁrmation tone.

Notes

• When the nightlight is turned on, the parent unit displays .

• The nightlight on baby unit operates even when the parent unit battery is out of charge or has been turned off.

• If the parent unit lost link, the nightlight icon on its LCD display will disappear, regardless of the nightlight

status.

Language

You can select a language (English, Spanish or French) to be used in all screen displays. The

language is preset to English.

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose LANGUAGE, then press SELECT.

3. Press VOL. or VOL. to choose ENGLISH, ESPANOL, or FRANCAIS.

4. Press SELECT to conﬁrm your selection. The screen displays SAVED and you hear

a conﬁrmation tone.

Note

• The language setting on each parent unit is independent.

Audio Reminder

With audio reminder feature preset to ON, the parent unit plays an audio reminder when

it is connected to a baby unit. It reminds you to place the baby unit at least 3 feet (1 meter)

away from your baby, and keep the cords out of the reach of children.

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose REMINDER, then press SELECT.

3. Press VOL. or VOL. to choose ON or OFF.

4. Press SELECT to conﬁrm your selection, and you hear a conﬁrmation tone.

Notes

• You can press VOL. or VOL. to adjust the volume when the parent unit is playing the reminder.

• If the speaker volume of the parent unit is turned off, it will change to the default volume level when the

parent unit plays the reminder.

Set default

Use this feature to restore to the default settings. Restoring the default settings on one

parent unit will also reset the shared settings for VOX sensitivity level of the other parent unit.

1. Press MENU/ when the parent unit is not in use.

2. Press VOL. or VOL. to choose SET DEFAULT, then press SELECT.

3. Press VOL. or VOL. to choose YES or NO.

4. When you choose YES, press SELECT to conﬁrm your selection, and you hear a

conﬁrmation tone.

-OR-

When you choose NO, press SELECT to conﬁrm your selection. The screen displays the

previous menu.

Talk to the baby unit

You can broadcast messages from a parent unit to the baby unit and the other parent unit. If

you have two parent units, you can use both of them at the same time to talk to the baby unit.

1. Press and hold TALK on the side of the parent unit. The screen displays TALK when the

voice connection to the baby unit is made.

2. Speak towards the MIC on the parent unit. Your voice is broadcast to the baby unit

and the other parent unit.

Notes

• If you have two parent units, and you use one of them to talk to your baby, your voice will be

broadcast to both the baby unit and the other parent unit. The other parent unit displays TALKBACK.

However, no sound will transmit from the baby unit to any parent unit during broadcasting.

• If speaker volume of the parent unit has been turned off before the talk, it will change to default

volume level after the talk ﬁnished.

Find/page the parent unit

Use this feature to locate misplaced parent units.

1. Press PAGE on the baby unit. All idle parent units ring and display PAGING.

2. To end paging, press any key on the parent unit, or press PAGE on the baby unit.

Notes

• Paging rings all parent units even if the speaker volume of parent unit is set to VOLUME OFF.

• The baby unit cannot page any parent unit that is turned off, out of range, or talking to the baby unit.

3 Using the baby monitor (Con’t)

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 1921.536-1928.448 MHz

Parent unit: 1921.536-1928.448 MHz

Channels 5

LCD 35 (x) x 21.2 (y) mm B&W LCD

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirement Parent unit: 2.4 V Ni-MH battery

Baby unit power adapter:

Output: 6V DC 400mA

Parent unit power adapter:

Output: 6V DC 400mA

Technical speciﬁcations

Speciﬁcations are subject to change without notice.

Document order number: 91-008851-070-100

THIS SIDE UP

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V

WARNING / AVERTISSEME

DO NOT BURN OR PUNCT

NE PAS INCINÉRER OU P

Made in China / Fabriqué

THIS SIDE UP / CE

THIS SIDE UP

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V

WARNING / AVERTISSEME

DO NOT BURN OR PUNCT

NE PAS INCINÉRER OU P

Made in China / Fabriqué

THIS SIDE UP / CE

THIS SIDE UP

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V

WARNING / AVERTISSEME

DO NOT BURN OR PUNCT

NE PAS INCINÉRER OU P

Made in China / Fabriqué

THIS SIDE UP / CE

THIS SIDE UP

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V

WARNING / AVERTISSEME

DO NOT BURN OR PUNCT

NE PAS INCINÉRER OU P

Made in China / Fabriqué

THIS SIDE UP / CE

LINKED

>6.5 feet

(2 meters)

< 6.5 feet

(2 meters)

> 6.5 feet (2 meters)

> 3 feet

(1 meter)

< 6.5 feet

(2 meters)

> 6.5 feet (2 meters)

> 3 feet

(1 meter)

Baby unit overview

1VOL.

• Press to decrease the speaker

volume.

2Microphone

3NIGHT LIGHT

• Press to turn the nightlight on or off.

4Nightlight

• On when nightlight is turned on

manually or triggered by sound.

• Off when nightlight is turned off

manually or after 15 minutes of

silence.

5POWER light

• On when the baby unit is turned on.

6VOL.

• Press to increase the speaker

volume.

7POWER

• Press to power on, the power light

turns on.

• Press and hold to power off, the

power light turns off.

8PAGE

• Press to start or stop paging parent

unit.

9Power jack

10 Speaker

Parent unit overview

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the

Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship,

pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product

operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United

States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option,

without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement

parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar

design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is

your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should

expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or

replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the

repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is

shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service

representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed,

altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used

for commercial or institutional purposes (including but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see item 2 below); or

8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In

Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save

you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will

return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited

warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping

costs for the repair of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of

purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral

communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized

to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation. State/Provincial Law Rights:

This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state or province to

province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/provinces

do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event

shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to

lost proﬁts or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and

claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Limited warranty

When using your equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock

and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and therefore you should not assume it will continue working

properly for any given period of time. Further, this is not a medical device and should not be used as such. This

product is intended to assist you in supervising your baby.

4. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub

or swimming pool, or in a wet basement or shower.

5. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is

used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT166342/BT266342)

for the parent unit. Do not dispose of batteries in a ﬁre. They may explode. Dispose of used battery according to the

information in The RBRC® seal.

6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.

Baby unit power adapter: Output: 6V DC 400mA;

Parent unit power adapter: Output: 6V DC 400mA.

7. The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

9. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

10. Unplug the power cords before replacing batteries.

11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or

crimped.

13. This product should be operated only from the type of power source indicated on the marking label. If you are not

sure of the type of power supply in your home, consult your dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back

or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be

blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near

or over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the product.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.

Opening or removing parts of the product other than speciﬁed access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

19. You should test the sound reception every time you turn on the units or move one of the components.

20. Periodically examine all components for damage.

21. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery

monitors, cordless phones, scanners, etc.

22. Children should be supervised to ensure that they do not play with the product.

23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF and 104oF.

2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or ﬁre.

4. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the

reach of children (more than 3 ft (0.9 m) away). Do not remove this tag.

5. Never place the baby unit inside the baby’s crib or playpen. Never cover the baby unit or parent unit

with anything such as a towel or a blanket.

6. Other electronic products may cause interference with your baby monitor. Try installing your baby

monitor as far away from these electronic devices as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.

• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding electromagnetic ﬁelds (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be used based on scientiﬁc evidence available today.

The RBRC® seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and recycle these batteries at the end of their useful

lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-metal batteries into the

trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s

involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery Recycling Corporation.

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base aﬁn de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilité du parent ou de la

personne qui s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il

continuera de fonctionner correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne

devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé.

4. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de

cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.

5. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais type de piles pour l’unité du parent. N’utilisez que

le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT166342/BT266342). N’incinérez pas les piles. Celles-ci risqueraient

d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRCMD.

6. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre votre sécurité en péril.

Adaptateur de l’unité du bébé: Sortie : 6 V CC 400 mA. Adaptateur de l’unité du parent: Sortie : 6 V CC 400 mA.

7. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si

celuici est branché dans une prise au plafond, sous une table ou dans un meuble.

8. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, aﬁn d’assurer une

accessibilité sécuritaire à la prise de courant.

9. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon

humide pour le nettoyer.

10. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.

11. Ne coupez pas les cordons d’alimentation pour remplacer les ﬁches, car ceci peut présenter un danger potentiel.

12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque

d’écraser le cordon d’alimentation ou de le piétiner.

13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.

14. Ne surchargez pas les prises de courant murales ni les rallonges électriques.

15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.

16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit,

divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un

calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de

liquide dans ce produit.

18. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou

ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite

présenter des risques d’électrocution.

19. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.

20. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas endommagées.

21. Soyez avisé de la perte de la conﬁdentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones sans ﬁl, des scanneurs, etc.

22. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne jouent pas avec l’appareil.

23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné sufﬁsamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, à au moins 1 mètre

(3 pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)

portative avec un article tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans ﬁl, radios,

téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche indépendante, a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans ﬁl portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la ﬁrme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-

ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientiﬁques dont nous disposons aujourd’hui.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby

monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install

and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is

paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part

15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely

absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found

to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained

at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in

(2.5 cm) from your face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference, including interference that may cause undesired operation.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations

were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit

should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body.

For body worn operation, this parent unit has been tested and meets the FCC RF exposure guidelines when used with

the accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC

RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for

Exposure of Humans to RF Fields.

The RBRC® seal For c-UL compliance only

California Energy Commission battery

charging testing mode

FCC and IC regulations

Important safety instructions

Below are the questions most frequently asked about the baby monitor. If you cannot ﬁnd the answer to your

question, visit our website at www.vtechphones.com or call 1 (800) 595-9511 for customer service.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby unit and the parent unit.

2. Remove the batteries in the parent unit. Then, install the batteries again.

3. Wait a few minutes before connecting power back to the baby unit and the parent unit.

4. Turn on the baby unit and the parent unit.

5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for

this to take place.

Why doesn’t the screen

of the parent unit go on

when I switch on the unit?

Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not

connected to the power. Insert the appliance plug into the parent unit and put the

adapter in a wall socket.

Why doesn’t the power

light of the baby unit go on

when I switch on the unit?

Perhaps the baby unit is not connected to the power. Connect the baby unit to the

power.

Why does the baby

monitor produce a

high-pitched noise?

The units may be too close to each other. Make sure the parent unit and the baby unit

are more than 6.5 feet (2 meters) away from each other.

Why does the parent unit

react too quickly to other

sounds?

The baby unit also detects other sounds than those of your baby. Adjust the VOX

sensitivity level to a lower level or adjust the speaker volume on the parent unit.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

The volume of the parent unit may have set too low. Press VOL. to increase the volume

level.

You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby

unit to change the setting.

Why does the parent unit

beep? If the sound alert feature is on, there is sound detected from the baby unit.

The baby unit may be out of range. Move the parent unit closer to the baby unit (but not

less than 6.5 feet).

If the parent unit is powered by the provided battery, it may not have enough charge for

the parent unit to perform normally. Charge the battery in the parent unit for up to 11 hours.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby unit may be out of range. Move the parent unit closer to the baby unit (but not

less than 6.5 feet).

Other electronic products may cause interference with your baby monitor. Try installing

your baby monitor as far away from these electronic devices as possible.

Why doesn’t the battery

icon shown on LCD display

even I have properly

installed the battery?

The battery may not be working. Contact our customer service to purchase a new

battery.

Frequently asked questions

When you are not going to use the baby monitor for some time, remove the rechargeable battery from the

parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.

Storage

To keep this product working well and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors

or fluorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry before you connect them to the mains again.

General product care

Parent unit icons

Status icons

Connection status

• displays when strong signal strength is detected between the baby unit and

the parent unit.

• displays when moderate signal strength is detected between the baby unit

and the parent unit.

• displays when the weak signal strength is detected between the baby unit and

the parent unit.

• ﬂashes when the link between the baby unit and the parent unit is lost.

Nightlight

• Displays when the nightlight is turned on.

Sound alert

• Displays when the sound alert of the parent unit is turned on.

• Flashes when there are loud sounds detected from the baby unit.

Vibration alert

• Displays when the vibration alert of the parent unit is turned on.

• Flashes when there are loud sounds detected from the baby unit.

Volume off

• Displays when the patient unit speaker volume is turned off.

Battery status

• animates when the battery is charging.

• displays solid when the battery is fully charged.

• ﬂashes when the battery is in low level and needs charging.

• No battery icon displays when there is no battery installed.

Parent unit display screen messages

LINKED • The link between the parent unit and the baby unit is established.

LOW BATTERY • The parent unit uses only the rechargeable battery pack and it

needs to be recharged.

NOT LINKED • The link between the parent unit and the baby unit is lost

continuously for over 10 seconds.

SAVED • Your selection has been saved.

SEARCHING • The parent unit is out of range of the baby unit, or the baby unit is

out of power.

TALK • You are using the parent unit to talk to your baby.

TALKBACK • Someone is using the other parent unit to talk to the baby, and

the voice is also broadcasting to your parent unit. No sound will

transmit from the baby unit to any parent unit during broadcasting.

• For DM223-2 only

1Microphone

2VOL.

• Press to decrease the speaker volume.

• While in a menu, press to scroll down.

3Speaker

4MENU/

• Press to enter the menu while idle.

• While in a menu, press to return to the

previous screen.

• Press to return to idle screen.

5Visual sound indicator

The visual sound indicator has two

functions. One is to show the sound level

detected by the baby unit. The other

one is to show the volume level during

speaker volume setting.

Sound level detected by the baby unit

• One to three

green lights indicate a moderate sound

level detected by the baby unit.

• Additional red

lights indicate a higher sound level

detected by the baby unit (e.g. baby

crying loudly).

Speaker volume level

• One to three

green lights indicate Level 1 to Level 3

of the speaker volume setting.

• Additional red

lights indicate Level 4 to Level 5 of the

speaker volume setting.

6LCD panel

7 Battery level indicator

• Light on when the battery is being

charged.

• Light ﬂashes when the battery is low

and needs charging.

• Light off when no battery is installed, or

abnormal battery is detected.

8VOL.

• Press to increase the speaker volume.

• While in a menu, press to scroll up.

9SELECT

• While in a menu, press to choose an

item, or save a setting.

10 (On/off)

• Press and hold to power on, the

screen turns on.

• Press and hold to power off, the screen

turns off.

• While in a menu, press to return to idle

screen.

11 TALK

• Press and hold to talk to the baby unit;

release to stop talking.

• While in a menu, press to return to

idle screen.

12 Power jack

13 Belt clip

14 Battery compartment cover

VTech Digital Audio Monitor Manuel utilisateur

Marque: VTech

Modèle: Digital Audio Monitor

Catégorie: Babyphones

Taper: Manuel utilisateur

Ce manuel convient également à

DM223

Télécharger le PDF

rapport

dans d''autres langues

English: VTech Digital Audio Monitor User manual

VTech Digital Audio Monitor Manuel utilisateur

Ce manuel convient également à

VTech Digital Audio Monitor Manuel utilisateur

dans d''autres langues

Documents connexes