GE UVW9301SLSS Le manuel du propriétaire

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label

on the inside of the hood.

ESPAÑOL

Para consultar una version en

español de este manual de

instrucciones, visite nuestro sitio de

internet GEAppliances.com.

WALL HOODS

49-2000896 Rev. 1 05-21 GEA

GE is a trademark of the General Electric Company. Manufactured under trademark license.

UVW9301

UVW9361

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

SAFETY INFORMATION .............3

USING THE HOOD

Controls ..................................5

Chef Connect ............................ 6

Wi-Fi Connect ............................ 6

CARE AND CLEANING

Filters ....................................7

Surfaces ..................................8

Lights ....................................8

INSTALLATION INSTRUCTIONS ... 9

TROUBLESHOOTING TIPS ..........21

LIMITED WARRANTY .............. 22

ACCESSORIES ...................... 23

CONSUMER SUPPORT ............. 24

FRANÇAIS

Pour une version français de

ce manuel d’utilisation, veuillez

visiter notre site web à l’adresse

GEAppliances.com.

2 49-2000896 Rev. 1

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-2000896 Rev. 1 3

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

B. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the

service panel.

C. Do not use this unit with any solid-state speed

control device.

D. This unit must be grounded.

CAUTION

FOR GENERAL VENTILATING USE

ONLY. DO NOT USE TO EXHAUST HAZARDOUS

OR EXPLOSIVE MATERIALS AND VAPORS.

CAUTION

TO REDUCE RISK OF FIRE AND

TO PROPERLY EXHAUST AIR, BE SURE TO DUCT

AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO

SPACES WITHIN WALLS OR CEILINGS OR INTO

ATTICS, CRAWL SPACES OR GARAGES.

WARNING

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher,

and you already know how to operate it.

2. The fire is small and contained in the area where

it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety” published by NFPA.

4 49-2000896 Rev. 1

How to Remove Protective Shipping Film and Packaging Tape

Carefully grasp a corner of the protective shipping film

with your fingers and slowly peel it from the appliance

surface. Do not use any sharp items to remove the film.

Remove all of the film before using the appliance for the

first time.

To assure no damage is done to the finish of the

product, the safest way to remove the adhesive from

packaging tape on new appliances is an application of

a household liquid dishwashing detergent. Apply with a

soft cloth and allow to soak.

NOTE: The adhesive must be removed from all parts.

NOTE: For further cleaning instructions/suggestions,

please refer to the Care And Cleaning section.

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on

medium settings.

B. Always turn hood ON when cooking at high heat or

when flambéing food (i.e. Crepes Suzette, Cherries

Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with all

applicable codes and standards, including fire-rated

construction.

B. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards such as those

published by the National Fire Protection

Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE) and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. When applicable, install any makeup (replacement)

air system in accordance with local building

code requirements. Visit GEAppliances.com for

available makeup air solutions.

F. Turn off breaker to adjacent rooms while working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCTWORK.

Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU

hood unless it is specifically recommended in this

manual. All other servicing should be referred to a

qualified technician.

49-2000896 Rev. 1 5

Controls

USING THE HOOD: Controls

1. Rangehood Control Panel: The control

panel is located on the front of the canopy. The

position and function of each control pad are

noted below.

2. On/Off: On/Off switch for the fan and lighting up

the display. The fan can be operated by tapping

any of the fan setting pads. Hold On/Off pad for

3 seconds to activate Delay Off feature, which

automatically turns the fan off after 15 minutes.

3. Fan Setting: Speed control for fan. Tap Low

for LOW speed. Med for MEDIUM speed and High

for HIGH speed. Press and hold the High pad

for 3 seconds to activate the BOOST speed that

will run for 10 minutes. On Remote, press Ÿ to

increase fan speed, press ź to decrease fan speed,

including Boost.

4. Plus and Minus: The plus (+) and minus (–)

pads control the time for the clock and the timer.

To add time, tap the + pad. To subtract time, tap

the – pad.

5. Timer: Sets a timer for cooking or sets the clock.

To start the timer, tap the Timer pad and the clock

will show “HR” and “MIN”. Tap + or – to add or

subtract time. Tap on the Timer again to start the

countdown. To cancel the timer, tap the Timer pad

again. Hold the Timer pad down for 3 seconds to

set the clock. Tap the + or – to set the the hour.

Tap on the Timer again to set minutes. Tap on the

Timer again to lock in the time. Clock will sync once

the unit is connected to Wi-Fi.

6. Light: Controls the lights. Tap the Light pad to

turn the lights on fully. Tap the Light pad again and

the lights will dim. Tap the Light pad a third time to

turn off the lights.

7. Chef Connect: Hold the Chef Connect pad

down for 3 seconds to activate the Bluetooth

®

. This

is a Bluetooth

®

pairing feature for use with other

compatible Chef Connect enabled products on a

cooktop or range. When the device is paired, the light

and fan will turn ON at the Default Sync Settings upon

receiving a command from the range or cooktop. It

will remain ON at that setting until the user changes

it. See the Chef Connect section for more details.

8. Reset Filter: The red LED indicator above the

Reset Filter pad turns on as a reminder to change

/clean the filter. Hold the Reset Filter pad for 3

seconds to turn off. Tap the Reset Filter pad again

to begin recalculating the time. While this indicator

reminds user to change/clean filters, the filters

should be cleaned regularly. Please refer to the

Filters section.

9. Wi-Fi: Hold down the Light and Chef Connect

pads for three seconds to activate the Wi-Fi connect

mode. The Wi-Fi symbol above the clock blinks for

3 seconds and then becomes solid. See the Wi-Fi

section for more details. On Remote, press Wi-Fi to

toggle Wi-Fi function.

10. Delay Off (Remote only): Press and hold

Delay Off to toggle Delay Off function.

3

4

25678

1 9

10

Remote Control

6

9

2

7

3

6 49-2000896 Rev. 1

Wi-Fi Connect

USING THE HOOD: Chef Connect / Wi-Fi Connect

* Compatible Apple or Android devices and home Wi-Fi network required.

Connecting your Wi-Fi Connect Enabled hood (on some models)

Your GE Appliances hood is designed to provide you with two-way communication between your appliance and smart

device. By using the GE Appliances Wi-Fi Connect features, you will be able to control essential hood operations such

as fan speed, light functions, timer/clock function, delay off and filter reset using your smartphone or tablet.*

What you will need

Your GE Appliances hood uses your existing home Wi-Fi

network to communicate between the appliance and your

smart device. In order to setup your GE Appliances hood,

you will need to gather some information:

1. Each GE Appliances hood has a connected

appliance information label that includes an

Appliance Network Name and Password. These

are the two important details that you will need to

connect to the appliance. The label is located on the

side of the unit behind the filters.

2. Have your smart phone or tablet ready with the ability

to access the internet and download apps.

3. You will need to know the password of your home

Wi-Fi router. Have this password ready while you are

setting up your GE Appliances hood.

Connect your GE Appliances hood

1. On your smart phone or tablet visit

GEAppliances.com/connect to learn more about

connected appliance features and to download the

appropriate app.

2. Follow the app onscreen instructions to connect your

GE Appliances hood.

3. Once the process is complete, the connection light

located on your GE Appliances hood display will stay

on solid and the app will confirm you are connected.

4. If the connection light does not turn on or is blinking,

follow the instructions on the app to reconnect. If

issues continue please call 800.220.6899 and ask for

assistance regarding hood wireless connectivity.

To connect additional smart devices, repeat steps 1 and 2.

Note that any changes or modifications to the remote

enable device installed on this hood that are not

expressly approved by the manufacturer could void the

user’s authority to operate the equipment.

Chef Connect Operation Bluetooth

®

Connection

To pair with another device:

To start the pairing process on the hood, press and hold

the Chef Connect button for 3 seconds. The backlight

for all the icons will light up until the hood is paired with

the range or other device. If the pairing is successful,

the Bluetooth

®

symbol above the clock will turn on and

become solid.

It will time out after 2 minutes if the pairing is not

completed, after which the pairing sequence will need to

be restarted.

To cancel pairing:

To cancel the pairing, hold the Chef Connect button

down for 3 seconds and then turn off the hood.

Default Sync Settings:

The factory default setting for the light will be the brightest.

The factory default setting for the fan sync will be OFF.

The user can change the Default Sync Settings by

pressing and holding the Low button for 3 seconds. This

will enter the Default Settings Mode. Once in this mode,

the backlights for all buttons will blink on/off indefinitely

and the fan and light will switch to the current Default

Sync Setting, so the user knows what the current default

value is. At this time, set the light and fan to the desired

default levels. Once the user is satisfied with the selection,

press and hold the Off button for 3 seconds. This will exit

this mode. At that time the backlights will stop blinking and

the state of the fan and light will change back to their prior

state before entering the Default Settings Mode.

Chef Connect

Sample Label

Connected Appliance Information

FCC ID: ZKJ-WCATA005

IC: 10229A-WCATA001

MAC ID: ************

Network: ************

Password: **********

49-2000896 Rev. 1 7

Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

Metal Grease Filter

The metal filters trap grease during cooking.

The filters must ALWAYS be in place when the hood

is in use. The grease filters are dishwasher-safe and

should be cleaned every month, depending on the

usage of the hood.

To remove:

Open the filter cover panel and disengage the filter lock

to release the filter.

To replace:

Fit the tabs at the bottom of the filter into the slots in the

back of the filter opening. Lift up the front side of the filter

and push gently until the filter locks into place. Make sure

the filter lock is in the closed position to secure the filter.

NOTE: The front panel covers the filters and must be

pressed up and then pulled down to access the filters.

To clean:

Swish the filter in hot soapy water and rinse in clean

water or wash it in the dishwasher. Do not use abrasive

cleansers.

NOTE: Some discoloration of the filter may occur in the

dishwasher.

Charcoal Filter (for recirculation installation only)

If the model is not vented to the outside, the air needs to

be recirculated through a disposable charcoal filter that

helps remove smoke and odors.

NOTE: DO NOT rinse, or put charcoal filter in an

automatic dishwasher.

The charcoal filter is included with the unit. It cannot

be cleaned, It must be replaced when Reset Filter

LED indicator comes on. It is recommended that the

charcoal filter be replaced every 6 months or if it is

noticeably dirty or discolored.

Order Charcoal Filter UXCF91

To inquire about purchasing replacement charcoal filters

or to find the location of a dealer nearest you, please call

our toll-free number:

National Parts Center 800.626.2002

In Canada, call 800.661.1616 or visit geappliances.ca

To install:

1. Remove the metal filters—see Metal Grease Filter

section.

2. Install the charcoal filter mounts to either side of the

motor using three screws per side.

3. Insert the tab on the charcoal filter into the triangular

slot on the mount.

4. Clip the charcoal filter in until it is locked.

5. Repeat with second filter on the other side of the motor.

6. Replace the metal filters - See Metal Grease Filter section.

To remove:

1. Remove the metal filters—see Metal grease filter

section.

2. Unclip the charcoal filter by pressing the release clip.

3. Carefully remove charcoal filter from tab.

Filters

CARE AND CLEANING: Filters

Charcoal

Filter Mount

8 49-2000896 Rev. 1

Lights

Painted Surfaces and Black Stainless Color (on some models)

Do not use a steel wool pads or other abrasive

cleaners; they will scratch the surface.

Clean grease-laden surfaces of the hood frequently. To

clean the hood surface, use a hot, damp cloth with a

mild detergent suitable for painted surfaces. About one

tablespoon of ammonia may be added to the water. Use

a clean, hot, damp cloth to remove soap. Dry with a dry,

clean cloth.

NOTE: When cleaning, take care not to come in contact

with filters and other surfaces.

CAUTION

When cleaning the hood surfaces,

be certain that you do not touch the light with moist

hands or cloth. A warm or hot light may break if

touched with a moist surface. Always let the light

cool completely before cleaning around it.

CAUTION

Allow lights to cool before touching.

1. Before attempting to replace the lights, make sure that

the light switch is turned off.

2. Rotate light counterclockwise to unlock and pull out.

Wearing latex gloves may offer a better grip.

3. Replace with new light of same type, making sure

pins are inserted properly into the sockets of the lamp

holder and turn clockwise to lock.

All lamps need to be GU10 compatible.

Surfaces

CARE AND CLEANING: Surfaces / Lights

Rotate the lamp until the

pins are located in narrow

neck of the socket to lock.

Lamp

Holder

Stainless Steel Surfaces (on some models)

Do not use a steel wool pad; it will scratch the

surface.

To clean the stainless steel surface, use warm sudsy

water or a stainless steel cleaner or polish. Always wipe

the surface in the direction of the brush line. Follow

the cleaner instructions for cleaning the stainless steel

surface. Cleaners with oxalic acid such as Bar Keepers

Friend Soft Cleanser™ will

remove surface rust, tarnish, and

small blemishes. To receive a

coupon for a trial sample of Bar

Keepers Friend Soft Cleanser™

follow the link below or scan the

QR Code.

www.barkeepersfriend.com/ge

Use only a liquid cleanser free of grit and rub in the

direction of the brush lines with a damp soft sponge.

To inquire about purchasing stainless steel appliance

cleaner or polish, or to find the location of a dealer

nearest you, please call our toll-free number:

National Parts Center

800.626.2002

GEApplianceParts.com

In Canada, call 800.661.1616 or visit geappliances.ca

49-2000896 Rev. 1 9

Installation

Instructions

“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)

or visit our website at: GEAppliances.com. In Canada, visit GEAppliances.ca or call 800.561.3344.

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Ŷ

IMPORTANT — Save these

instructions for local inspector’s use.

Ŷ

IMPORTANT — Observe all governing

codes and ordinances.

Ŷ

Note to Installer – Be sure to leave these

instructions with the Consumer.

Ŷ

Note to Consumer – Keep these instructions for

future reference.

Ŷ

Skill level – Installation of this vent hood requires

basic mechanical and electrical skills.

Ŷ

Completion time – Approximately 1 to 3 hours

Ŷ

Proper installation is the responsibility of the

installer.

Ŷ

Product failure due to improper installation is not

covered under the Warranty.

FOR YOUR SAFETY

WARNING

Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,

to the service panel.

CAUTION

Due to the weight and size of

these vent hoods and to reduce the risk of personal

injury or damage to the product, TWO PEOPLE

ARE REQUIRED FOR PROPER INSTALLATION.

WARNING

Disconnect all electrical power

at the main circuit breaker or fuse box before

installing.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with

all applicable codes and standards, including

fire-rated construction.

B. Sufficient air is needed for proper combustion

and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment

manufacturer’s guidelines and safety standards

such as those published by the National Fire

Protection Association (NFPA), the American

Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local

code authorities.

C. When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden

utilities.

D. Ducted fans must always be vented to the

outdoors.

E. Turn off breaker to adjacent rooms while

working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCT WORK.

Wall Hoods

UVW9301, UVW9361

10 49-2000896 Rev. 1

Installation Preparation

INSTALLATION CLEARANCES

These vent hoods are designed to be installed onto

a wall with no above cabinets.

The vent hood must be installed between the 24”

required minimum and 36” recommended maximum

above the cooking surface. For supplied duct cover

ceiling heights, see Installation Height Table.

NOTE: Installation height should be measured from

the cooking surface to the lowest part of the hood.

The hood must be installed onto a wall. It can be

vented to the outdoors, or it can be installed for

recirculating operation. For recirculation operation,

see Recirculation Install Planning.

PRODUCT DIMENSIONS

INSTALLATION PREPARATION

26-5/8Ǝ min. - 50-7/8Ǝ max.

12-1/4Ǝ

2-3/4Ǝ

4-5/8Ǝ

13-13/16Ǝ

25-3/4Ǝ

30ƎRUƎ

20Ǝ

24” Required Min.

36” Recommended Max.

20Ǝ

30ƎRUƎ

Filter Cover Panel

12-1/8Ǝ

8Ǝ

6-15/16Ǝ

10-5/8Ǝ

Installation instructions, describing the intended

mounting and wiring of the range hood cord

connection kit, shall be provided with each range

hood cord connection kit.

1" = 2.5 cm

49-2000896 Rev. 1 11

INSTALLATION PREPARATION

Installation Preparation

PLAN THE INSTALLATION

CAUTION

To reduce risk of fire and to

properly exhaust air, be sure to duct the air outside.

Do not vent exhaust air into spaces within walls or

ceilings or into attics, crawl spaces, or garages.

PARTS SUPPLIED FOR INSTALLATION

Ŷ 1 Hardware Package

Ŷ 1 Literature Package

Ŷ Recirculation Duct (for recirculation install only)

Ŷ Charcoal filters (recirculation mode)

PARTS NEEDED FOR INSTALLATION

Ŷ 1 Strain Relief

Ŷ 1 Wall or Roof Cap (for ducted venting only)

Ŷ All Metal Ductwork (for ducted venting only)

WARNING

PERSONAL INJURY HAZARD

Because of the weight and size of the rangehood

canopy. It is recommended that 2 people are used

to install the range hood. Failure to properly lift

rangehood could result in damage to the product or

personal injury.

NOTE: This rangehood can be installed as either

ducted or recirculation. In a ducted application,

this rangehood can be vented through the wall

or ceiling. When installed for recirculation, the

rangehood vents out the sides of the duct cover.

NOTE: Before making any cuts or holes for

installation, determine which venting method will be

used and carefully calculate all measurements.

TOOLS AND MATERIALS REQUIRED

(NOT SUPPLIED)

REMOVE THE PACKAGING

CAUTION

Wear gloves to protect against

sharp edges.

Ŷ Remove the duct covers.

Ŷ Remove the hardware bag, literature package

and other boxed parts.

Ŷ Remove and properly discard the protective

plastic wrapping and other packaging materials.

Wire cutter/stripper

Level

Aluminized

duct tape

Safety glasses

Phillips screwdriver

Strain relief for

junction box

Electric drill with #2 Phillips

and 1/8" drill bits

UL listed wire nuts

8" round duct

(length will vary)

Pencil and tape measure

Gloves

Use only with range hood cord connection kits that

have been investigated and found acceptable for

use with this model range hood.

1" = 2.5 cm

12 49-2000896 Rev. 1

Installation Preparation

INSTALLATION DIMENSIONS

The Wall Hoods duct covers can be adjusted for

different ceiling heights depending on the distance

between the bottom of the hood and the cooktop

(distance X). See Installation Height Table.

RANGE HOOD COMPONENTS

RECIRCULATION COMPONENTS

INSTALLATION PREPARATION

A. Wall Hood

B. Upper Duct Cover

C. Lower Duct Cover

D. Mounting Screws

E. Duct Cover

Mounting Bracket

F. Damper

G. Hood Mounting

Bracket

H. Mounting Anchors

J. Machine Screws

K. Recirculation Box

L. Wood Screws

7/8Ǝ min

25-1/8Ǝ max

25-3/4Ǝ

2-3/4Ǝ

36”

X

X = Distance From Hood To

Cooktop

(Varies depending on installation)

Required Min - 24”,

Recommended Max - 36”

Also consult cooktop

manufacturer’s recommendation

For higher ceiling

installations up to

12', use the 12' High

Ceiling Duct Cover

kit (UX12DC93) for

your model.

For higher ceiling

installations up to

14', use the 14' High

Ceiling Duct Cover

kit (UX14DC93) for

your model.

Typical Range

Upper Duct

Cover

Lower

Duct Cover

Hood Body

Required Min & Recommended

Max Ceiling Height Examples

X = 24" X = 36"

Min Min

7' 6" 9' 6"

Max Max

8' 6" 10' 5"

Required Min Ceiling

Height for Recirculation

X = 24" X = 36"

Min Min

7' 10" 8' 10"

K

A

D

F

J

E

D

J

K

J

H

G

L

C

B

J

H

D

L

HARDWARE COMPONENTS

NOTE: The chimney extension replaces the upper

and lower chimney shipped with the range hood.

The hardware included with the hood should be

saved and also used with the chimney extension.

E

L

H

J

Phillips Head

Wood Screw

3/16" x 1-15/16"

(QTY: 4)

Phillips Head

Machine Screw

1/8" x 3/8"

(QTY: 14)

Phillips Head

Mounting Anchors

Screws

3/16" x 1-1/2"

(QTY: 6)

Mounting Anchors

(QTY: 6)

D

1' = 0.3 m, 1" = 2.5 cm

49-2000896 Rev. 1 13

INSTALLATION PREPARATION

Installation Preparation

INSTALLATION HEIGHT TABLE

(UX12DC9SLSS or

UX12DC9BJTS)

(UX14DC9SLSS or

UX14DC9BJTS)

Installation Height with Supplied Duct Covers

Optional High Ceiling Duct Cover

up to 12 ft.

(not included with unit)

Optional High Ceiling Duct Cover

up to 14 ft.

(not included with unit)

Ceiling

Height (ft./in.)

Possible Vented

Install Height

(in.)

Possible Vented

Install Height

(Recirculation

vented Holes

Hidden) (in.)

Possible

Recirculation

Install

Height (in.)

Ceiling

Height (ft./in.)

Vented and

Recirculation

Height (in.)

Ceiling

Height (in.)

Vented and

Recirculation

Install

Height (in.)

7' 6" 24 24 9' 3" 24 12' 24-36

7' 7" 24-25 24-25 9' 4" 24-25 12' 1" 24-36

7' 8" 24-26 24-26 9' 5" 24-26 12' 2" 24-36

7' 9" 24-27 24-27 9' 6" 24-27 12' 3" 24-36

7' 10" 24-28 24-28 24 9' 7" 24-28 12' 4" 24-36

7' 11" 24-29 24-29 24-25 9' 8" 24-29 12' 5" 24-36

8' 24-30 24-30 24-26 9' 9" 24-30 12' 6" 24-36

8' 1" 24-31 24-31 24-27 9' 10" 24-31 12' 7" 24-36

8' 2" 24-32 24-32 24-28 9' 11" 24-32 12' 8" 24-36

8' 3" 24-33 24-33 24-29 10' 24-33 12' 9" 24-36

8' 4" 24-34 24-34 24-30 10' 1" 24-34 12' 10" 24-36

8' 5" 24-35 24-35 24-31 10' 2" 24-35 12' 11" 24-36

8' 6" 24-36 24-36 24-32 10' 3" 24-36 13' 24-36

8' 7" 24-36 24-36 24-33 10' 4" 24-36 13' 1" 25-36

8' 8" 24-36 24-36 24-34 10'5"-11'3" 24-36 13' 2" 26-36

8' 9" 24-36 24-36 24-35 11' 4" 24-36 13' 3" 27-36

8' 10" 24-36 24-36 24-36 11'5" 24-36 13' 4" 28-36

8' 11" 24-36 24-36 24-36 11'6" 24-36 13' 5" 29-36

9' 24-36 24-36 24-36 11'7" 24-36 13' 6" 30-36

9' 1" 24-36 24-36 24-36 11'8" 25-36 13' 7" 31-36

9' 2" 24-36 25-36 24-36 11'9" 26-36 13' 8" 32-36

9' 3" 24-36 26-36 24-36 11'10" 27-36 13' 9" 33-36

9' 4" 24-36 27-36 24-36 11' 11" 28-36 13' 10" 34-36

9' 5" 24-36 28-36 24-36 12' 29-36 13' 11" 35-36

9' 6" 25-36 29-36 25-36 14' 36

9' 7" 26-36 30-36 26-36

9' 8" 27-36 31-36 27-36

9' 9" 28-36 32-36 28-36

9' 10" 29-36 33-36 29-36

9' 11" 30-36 34-36 30-36

10' 31-36 35-36 31-36

10' 1" 32-36 36 32-36

10' 2" 33-36 33-36

10' 3" 34-36 34-36

10' 4" 35-36 35-36

10' 5" 36 36

*Based on a 36" electric range height.

For gas range, start chart at 92" and subtract 2" for the maximum install height for each block.

7/8Ǝ min

29-7/16Ǝ max

7/8Ǝ min

46-1/4Ǝ max

46-7/8" 46-7/8"

12" High Ceiling Duct Cover Kit 14" High Ceiling Duct Cover Kit

Upper

Duct Cover

Upper

Duct Cover

Lower

Duct Cover

Lower

Duct Cover

Hood Body Hood Body

1' = 0.3 m, 1" = 2.5 cm

14 49-2000896 Rev. 1

INSTALLATION PREPARATION

ADVANCE PLANNING

Duct Install Planning

Ŷ This hood is designed to be vented vertically

through the ceiling. Use an 8" round duct. Use

locally supplied elbows to vent horizontally

through the rear wall.

Ŷ Use metal ductwork only.

Ŷ Determine the exact location of the vent hood.

Ŷ Plan the route for venting exhaust to the

outdoors. To maximize the ventilation

performance of the vent system:

1. Minimize the duct run length and number of

transitions and elbows.

2. Maintain a constant duct size.

3. Seal all joints with duct tape to prevent any leaks.

NOTE: Flexible vent is not recommended. Flexible

vent creates back pressure and air turbulence that

greatly reduces performance.

Ŷ Maximum equivalent duct length for 100 CFM:

150 foot for vent hoods.

Ŷ Install a wall cap or roof cap with damper at the

exterior opening. Purchase the wall or roof cap

and any transition and length of duct needed in

advance.

Ŷ When applicable, install any makeup (replacement)

air system in accordance with local building code

requirements. Use makeup air kit JXMUA8.

Vent system can terminate either through the roof

RUWKHZDOO7RYHQWWKURXJKDZDOOD๦HOERZLV

needed and installed immediately above the hood.

Recirculation Install Planning

A recirculation duct (included) and charcoal

filter (included) are necessary for recirculation

installation.

Power Supply Planning

The location of the power supply connection is called

out in the Installing The Hood Bracket Mount section.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before

beginning installation.

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Codes or

prevailing local codes and ordinances.

Electrical supply

These vent hoods must be supplied with 120V,

60Hz, and connected to an individual, properly

grounded branch circuit, and protected by a 15 or

20 amp circuit breaker or time delay fuse.

Ŷ Wiring must be 2 wire with ground.

Ŷ If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

Ŷ Route house wiring as close to the installation

location as possible in the ceiling or wall.

Ŷ Connect the wiring to the house wiring in

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to

a ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING

The improper connection of the

equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician

or service representative if you are in doubt whether

the appliance is properly grounded.

Installation Preparation

Roof Cap

Round Duct

Wall Cap

Add Insulation

and/or Caulk

Add Insulation

and/or Caulk

Add tape to joint

Hood

1" = 2.5 cm

49-2000896 Rev. 1 15

NEW CONSTRUCTION, PRE-PLANNING, OR REMODELING

NOTE: For existing construction, skip to the section, Installing The Hood Bracket Mount.

Ŷ Install horizontal wood supports between 2 wall

studs that align with the vertical mounting height

locations shown in the illustration.

Ŷ The horizontal supports must be flush with the room

side studs.

Ŷ For ducted installation, the hole for the duct in the

ceiling must be centered 5" away from the finished

rear wall.

Ŷ The bottom support aligns with the hood mounting

bracket. This height depends on the desired height

of the hood.

Ŷ The top support must be flush with the ceiling.

Ŷ The electrical wiring can be located 5-1/2” to the left

or right (junction box is on the left) of the centerline.

Must remain 7/16” above the back panel and 5” from

the ceiling, refer to illustration on next page.

INSTALLATION

Installation

Acceptable

area for

electrical

wiring

Acceptable

area for

electrical

wiring

14-3/8"

5"

11"

See the Installation

Height Table for possible

installation heights.

24-36" + 1-1/8"

Wood Supports

• 36" minimum

width centered

• 4" height

From the lower left corner of

the gray shaded area, it is

recommended to have at least

20" of house electrical wiring.

* 36” or 38” Range

* Typical electrical range is 36"

and typical gas range is 38"

1" = 2.5 cm

16 49-2000896 Rev. 1

Installation

INSTALLATION

INSTALLING THE HOOD BRACKET MOUNT

Hood Body

1. Put a protective covering over the surface

below the location of the hood to protect from

dirt and/or damage.

2. Determine and mark the centerline (C) on the

wall (draw line up to the ceiling) where the range

hood will be installed. Based on the ceiling height,

determine the distance between 24” required

min, 36” recommended max (X) needed between

the cooking surface (B) and the bottom of the

hood. Draw a horizontal line at X. Align the install

template so that the bottom of the template is

centered and is level with the horizontal line drawn

at height X.

3. Find the stud locations and mark them on the

template.

4. Place the hood mounting bracket (G) on its outline

on the template. Mark at least one wood screw (L)

location that is on a stud. If another stud cannot be

found, mark at least two other screw locations for

mounting anchors, one on each side of the wood

screw (L). Remove the bracket from the wall and

install the mounting anchors (H). Place the hood

mounting bracket (G) back on the wall and mount it

with the wood screws (L) and mounting screws (D)

as needed. It is recommended to create a pilot hole

in the studs for wood screws (L).

Duct Covers and Power Supply

1. Place the duct cover bracket (E) on the wall so that

its edge is against the ceiling and level, making

sure the slots are in direct contact with the wall.

Align the center notches of the bracket and the

centerline. Mark the location of the screw holes

furthest apart from the center line if possible. If one

of the screw holes aligns with a stud, then a wood

screw will be used for that location. For the other

hole or if there are no studs, install 2 mounting

anchors (H). Place the duct cover bracket (E)

on the wall and install with wood screws (L) and

mounting screws (D) as needed.

2. The house electrical wiring must fall in the gray

shaded area shown below. From the lower left

corner of the shaded area, a minimum of 20” of

house electrical wiring is recommended to reach

the electrical junction box on the hood.

C

B

1-1/8"

X

24 to 36"

Hood Mounting Bracket

Mounting

Screw

Mounting

Screw

Wood Screw

Mounting

Anchors

Ǝ%HORZ&HLOLQJ

C

Ceiling

Ǝ

16-7/8"

Acceptable

area for house

electrical

wiring

1" = 2.5 cm

49-2000896 Rev. 1 17

INSTALLATION

INSTALLING THE HOOD

Remove the grease filters from

the unit and set aside. The

grease filters are removed by

pressing the handle in the front

of the filter. When replacing,

make sure that the filters are

properly positioned with the

handles in front and visible.

NOTE: On some models, the front panel covers the

filters and must be pulled down to access the filters.

NOTE: This bracket must be removed prior to

installation. Remove 2 front and 2 bottom screws per

illustration bellow.

1. Securely press the damper on top of the exhaust

opening. Check that the damper opens freely.

Attach damper to hood using machine screws

(J) provided.

2. Remove and properly discard the protective plastic

wrapping from the hood and grease filter. Remove

the template off the wall.

3. Mount the Range Hood:

Ŷ Using 2 or more people, lift the range hood and

place on the hood mounting bracket. Make sure

the bracket fully engages the hood body.

Ŷ Install the 2 mounting screws (D) or wood screws

(L) as needed into the designated holes on the

back panel.

Installation

18 49-2000896 Rev. 1

Installation

INSTALLATION

ELECTRICAL CONNECTION

1. Remove the electrical junction box cover.

2. Remove the electrical box knockout.

3. Feed the Power Supply Cable through the hole

and secure with a strain relief.

4. Attach the white lead of the power supply (A) to

the white lead of the range hood (D) with a wire

nut. Attach the black lead of the power supply (B)

to the black lead of the range hood (C) with a wire

nut. Connect the house ground wire under the

green grounding screw (E).

5. Reattach the electrical junction box cover.

INSTALLING THE HOOD (Cont.)

A

Vented Installations

Connect the house ducting to the damper on the

hood body. Seal all connections with duct tape

(Do not use screws).

B

Recirculation (Non-vented)

NOTE: A recirculation box, a charcoal filter, and a

bracket are included with the hood and are necessary

for recirculation installation.

1. Attach the recirculation box to the duct over

mounting bracket with 4 machine screws (J).

2.

Connect the ducting from the exhaust outlet on

the hood to the recirculation box. Use duct tape

to seal the connections on the recirculation box

and the exhaust outlet.

House Wiring

A

E

D

C

B

Hood Wiring

Electrical Box

Knockout with

Strain Relief

Ceiling

House

Ducting

Recirculation Box

Duct Cover

Mounting

Bracket

Use tape

(Do not use screws)

49-2000896 Rev. 1 19

INSTALL DUCT COVERS

1. For ducted and recirculation installation:

Remove protective film from duct covers. Place

the upper duct cover so that it slides down inside

of the lower duct cover.

NOTE: For recirculation, the upper duct cover

must be installed with the exhaust vents on the

top towards the ceiling.

Depending on the amount of overlap between

the top and bottom duct covers, the top may be

reversed to hide vent holes. Refer to Installation

Height Table for possible heights.

Place the set of duct covers by sitting them

down to fit securely on top of the hood. Finish

attaching the lower duct cover to the body of the

hood with two machine screws (J) that screw

from up underneath the hood.

2. Install the upper duct cover by carefully raising

it up to avoid scratching until it reaches the

ceiling. Push the duct cover flush against the

wall, then use two machine screws (J) to mount

the upper duct to the duct mounting bracket.

3. If recirculating, install the charcoal filters. Then

reinstall the grease filters to the hood, see the

Filters section.

4. Turn the power supply on. Turn on the blower

and light. If the range hood does not operate,

check that the circuit breaker is not tripped or the

house fuse blown. If the unit still does not operate,

disconnect the power supply and check that the

wiring connections have been made properly.

Installation

INSTALLATION

20 49-2000896 Rev. 1

Installation

INSTALLATION

MAKE UP AIR TECHNOLOGY

Note to Installers and Inspectors: This product comes equipped with a simple installation feature that limits

maximum CFM levels in order to comply with certain local codes or regulations. This installation method may not

be necessary for all installations, please refer to your local codes for further guidelines.

CAUTION

Hood must be disconnected from main power prior performing the conversion instructions

listed below. Failure to do so could result in personal injury or damage to the product.

To modify unit (if needed for local codes):

390CFM or 290CFM

By design, the maximum blower speed is greater than

400 CFM. For local codes requiring reduced CFM,

modify the wiring as described below:

1. Open the filter cover panel and remove the filters.

2. Remove the control board box cover.

3. Locate the motor harness plugged into the control

board.

4. A -

For a maximum of 390 CFM

Unit can operate with 4 speeds

(Low, Medium, High, Boost).

1. Disconnect the connector of the blue wire

from the red wire.

2. Connect the 2 red wires together.

3. Cut off the blue unused connector and crimp

the end if desired.

B -

For a maximum of 290 CFM

Unit can operate with 3 speeds

(Low, Medium, High).

1. Disconnect the connector of the blue wire

from the red wire.

2. Cut off the blue unused connector and crimp

the end if desired.

5. Reattach the control board box cover and install

Filters, see Filters section.

Note to Inspectors: To verify this product was

installed in either configuration, check motor wiring

connections as described above.

Motor Harness Connector

Blue

Red

Motor Harness

Control Board

Box Cover

La page charge ...

GE UVW9301SLSS Le manuel du propriétaire

Ce manuel convient également à

GE UVW9301SLSS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents