CONTINENTAL EDISON CEICT2 Manuel utilisateur

Induction Hob

Instruction Manual / Installation Manual

MODEL: CEICT2

2

Congratulations on the purchase of your new Induction Hob.

We recommend that you spend some time to read this Instruction / Installation

Manual in order to fully understand how to install correctly and operate it.

For installation, please read the installation section.

Read all the safety instructions carefully before use and keep this Instruction /

Installation Mnual for future reference.

Product Overview

Top View

Control Panel

1. max. 2000 W zone

2. max. 1500 W zone

3. Glass plate

4. ON/OFF control

5. Control panel

1. ON/OFF control

2. Power / Timer regulating controls

3. Heating zone selection controls

4. Timer control

5. keylock control

5

1

3

2

4

5

2

4

1

3

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking

technology. It works by electromagnetic vibrations generating heat directly in

the pan, rather than indirectly through heating the glass surface. The glass

becomes hot only because the pan eventually warms it up.

Before using your New Induction Hob

• Read this guide, taking special note of the ‘Safety Warnings’ section.

• Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

• The controls respond to touch, so you don’t need to apply any pressure.

• Use the ball of your finger, not its tip.

• You will hear a beep each time a touch is registered.

• Make sure the controls are always clean, dry, and that there is no object (e.g.

a utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

3

4

Choosing the right Cookware

• Only use cookware with a base suitable for induction

cooking. Look for the induction symbol on the

packaging or on the bottom of the pan.

• You can check whether your cookware is suitable by carrying out

a magnet test. Move a magnet towards the base of the pan. If it

is attracted, the pan is suitable for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

3. If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or

copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is

the same size as the cooking zone. Use pans whose diameter is as large as the

graphic of the zone selected.Using a pot a slightly wider energy will be used at

its maximum efficiency.If you use smaller pot efficiency could be less than

expected.Pot less than 140 mm could be undetected by the hob. Always centre

your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the

glass.

2. Follow the steps under ‘To start cooking’ on page 5.

5

Using your Induction Hob

To start cooking

1. Touch the ON/OFF control.

After power on, the buzzer beeps once, all displays

show “ – “ or “ – – “, indicating that the induction

hob has entered the state of standby mode.

2. Place a suitable pan on the cooking zone that

you wish to use.

• Make sure the bottom of the pan and the surface

Of the cooking zone are clean and dry.

3. Touching the heating zone selection control

(e.g. zone 1#),and a indicator next to the

key will flash

6

4. Select a heat setting by touching the ”-“ or “+”

control.

• If you don’t choose a heat setting within 1

minute, the Induction hob will automatically

switch off. You will need to start again at

step 1.

• You can modify the heat setting at any time

during cooking.

If the display flashes alternately with the heat

setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centred on the cooking

zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically turn off after 2 minutes if no suitable pan is

placed on it.

When you have finished cooking

1. Touching the heating zone selection

control that you wish to switch off

(e.g. zone 1#),

7

2. Turn the cooking zone off by scrolling down to” 0” or touching”-“ and”+”

control together. Make sure the display shows”0”

3. Turn the whole cooktop off by touching the ON/OFF control.

4. Beware of hot surfaces

will show which cooking zone is hot to touch. It will disappear when the

surface has cooled down to a safe temperature. It can also be used as an

energy saving function if you want to heat further pans, use the hotplate

that is still hot.

8

Locking the Controls

• You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are

disabled.

To lock the controls

Touch the keylock control. The timer indicator will show “ “

To unlock the controls

1. Make sure the Induction hob is turned on.

2. Touch and hold the keylock contro for 2 seconds.

3. You can now start using your Induction hob.

When the hob is in the lock mode,all the controls are disable except the

ON/OFF ,you can always turn the ceramic hob off with the ON/OFF

control in an emergency,but you shall unlock the hob first in the next

operation

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the

Induction hob. When an excessive temperature is monitored, the Induction hob

will stop operation automatically.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other

small item (e.g. knife, fork, key) has been left on the hob, the hob automatically

go on to standby in 1 minute. The fan will keep cooking down the induction hob

for a further 1 minute.

Auto Shutdown Protection

Auto shut down is a safety protection function for your induction hob. It shut

down automatically if ever you forget to turn off your cooking. The default

working times for various power levels are shown in the below table: .

9

Power level 1 2 3 4 5 6 7 8 9

Default working timer (hour) 8 8 8 4 4 4 2 2 2

When the pot is removed, the induction hob can stop heating immediately and

People with a heart pace maker should consult with their doctor before

using this unit.

Using the Timer

You can use the timer in two different ways:

• You can use it as a minute minder. In this case, the timer will not turn any

cooking zone off when the set time is up.

• You can set it to turn one cooking zone off after the set time is up.

• You can set the timer for up to 99 minutes.

Using the Timer as a Minute Minder

If you are not selecting any cooking zone

1. Make sure the cooktop is turned on.

Note: you can use the minute minder even

if you’re not selecting any cooking zone.

2. Touch timer control , The minder indicator

will start flashing and “10” will show in the

timer display.

the hob swicth off after

2 minutes.

10

3. Set the time by touching the “-“ or “+” control

of the timer

Hint: Touch the “-“ or “+” control of the timer

once to decrease or increase by 1 minute.

Hold the “-“ or “+” control of the timer to

decrease or increase by 10 minutes.

If the setting time exceeds 99 minutes, the timer

will automatically return to 00 minute.

4. Touching the”-“ and “+” together, the timer is cancelled, and the”00” will

show in the minute display.

5. When the time is set, it will begin to count down

immediately. The display will show the remaining

time and the timer indicator will flash for 5 seconds.

6. Buzzer will bips for 30 seconds and the timer

indicator shows “- - “ when the setting time

finished.

11

Setting the timer to turn one cooking zone off

Cooking zones set for this feature will:

1. Touching the heating zone selection control

that you want to set the timer for. (e.g. zone 1#)

2. Touch timer control , The minder indicator

will start flashing and “10” will show in the

timer display.

3. Set the time by touching the”-“ or”+” control of the

timer

Hint: Touch the “-“ or “+” control of the timer

once will decrease or increase by 1 minute.

Touch and hold the “-“or”+” control of the timer

will decrease or increase by 10 minutes.

If the setting time exceeds 99 minutes, the timer

will automatically return to 00 minute.

4. Touching the”-“ and “+” together, the timer is cancelled, and thewill show

” 00”in the minute display.

12

5. When the time is set, it will begin to count down

immediately. The display will show the remaining

time and the timer indicator flash for 5 seconds.

NOTE: The red dot next to power level indicator

will illuminate indicating that zone is selected.

6. When cooking timer expires, the corresponding

cooking zone will be switch off automatically.

Other cooking zone will keep operating if they are turned on previously.

Cooking Guidelines

Take care when frying as the oil and fat heat up very quickly,

particularly if you’re using PowerBoost. At extremely high

termperatures oil and fat will ignite spontaneously and this presents a

serious fire risk.

Cooking Tips

• When food comes to the boil, reduce the temperature setting.

• Using a lid will reduce cooking times and save energy by retaining the heat.

• Minimise the amount of liquid or fat to reduce cooking times.

• Start cooking on a high setting and reduce the setting when the food has

heated through.

13

Simmering, cooking rice

• Simmering occurs below boiling point, at around 85C, when bubbles are just

rising occasionally to the surface of the cooking liquid. It is the key to delicious

soups and tender stews because the flavours develop without overcooking the

food. You should also cook egg-based and flourthickened sauces below boiling

point.

• Some tasks, including cooking rice by the absorption method, may require a

setting higher than the lowest setting to ensure the food is cooked properly in

the time recommended.

Searing steak

To cook juicy flavoursome steaks:

1. Stand the meat at room temperature for about 20 minutes before cooking.

2. Heat up a heavy-based frying pan.

3. Brush both sides of the steak with oil. Drizzle a small amount of oil into the

hot pan and then lower the meat onto the hot pan.

4. Turn the steak only once during cooking. The exact cooking time will depend

on the thickness of the steak and how cooked you want it. Times may vary

from about 2 – 8 minutes per side. Press the steak to gauge how cooked it

is – the firmer it feels the more ‘well done’ it will be.

5. Leave the steak to rest on a warm plate for a few minutes to allow it to relax

and become tender before serving.

For stir-frying

1. Choose an induction compatible flat-based wok or a large frying pan.

2. Have all the ingredients and equipment ready. Stir-frying should be quick. If

cooking large quantities, cook the food in several smaller batches.

3. Preheat the pan briefly and add two tablespoons of oil.

4. Cook any meat first, put it aside and keep warm.

5. Stir-fry the vegetables. When they are hot but still crisp, turn the cooking

zone to a lower setting, return the meat to the pan and add your sauce.

6. Stir the ingredients gently to make sure they are heated through.

7. Serve immediately.

14

Heat Settings

The settings below are guidelines only. The exact setting will depend on several

factors, including your cookware and the amount you are cooking. Experiment

with the induction hob to find the settings that best suit you.

Heat setting Suitability

1 - 2

• delicate warming for small amounts of food

• melting chocolate, butter, and foods that burn quickly

• gentle simmering

• slow warming

3 - 4

• reheating

• rapid simmering

• cooking rice

5 - 6

• pancakes

7 - 8

• sautéing

• cooking pasta

9

• stir-frying

• searing

• bringing soup to the boil

• boiling water

Care and Cleaning

The settings below are guidelines only. The exact setting will depend on several

factors, including your cookware and the amount you are cooking. Experiment

with the cooktop to find the settings that best suit you.

What? How? Important!

Everyday soiling on

glass (fingerprints,

marks, stains left by

food or non-sugary

spillovers on the

glass)

1. Switch the power to the

cooktop off.

2. Apply a cooktop cleaner

while the glass is still warm

(but not hot!)

3. Rinse and wipe dry with a

clean cloth or paper towel.

4. Switch the power to the

cooktop back on.

• When the power to the cooktop is

switched off, there will be no ‘hot

surface’ indication but the cooking

zone may still be hot! Take extreme

care.

• Heavy-duty scourers, some nylon

scourers and harsh/abrasive

cleaning agents may scratch the

glass. Always read the label to

check if your cleaner or scourer is

suitable.

• Never leave cleaning residue on the

15

cooktop: the glass may become

stained.

Boilovers, melts,

and

hot sugary spills on

the glass

Remove these immediately

with a fish slice, palette knife or

razor blade scraper suitable for

Induction glass cooktops, but

beware of hot cooking zone

surfaces:

1. Switch the power to the

cooktop off at the wall.

2. Hold the blade or utensil at a

30° angle and scrape the

soiling or spill to a cool area

of the cooktop.

3. Clean the soiling or spill up

with a dish cloth or paper

towel.

4. Follow steps 2 to 4 for

‘Everyday soiling on glass’

above.

• Remove stains left by melts and

sugary food or spillovers as soon

as possible. If left to cool on the

glass, they may be difficult to

remove or even permanently

damage the glass surface.

• Cut hazard: when the safety cover

is retracted, the blade in a scraper

is razor-sharp. Use with extreme

care and always store safely and

out of reach of children.

Spillovers on the

touch controls

1. Switch the power to the

cooktop off.

2. Soak up the spill

3. Wipe the touch control area

with a clean damp sponge or

cloth.

4. Wipe the area completely

dry

with a paper towel.

5. Switch the power to the

cooktop back on.

• The cooktop may beep and turn

itself off, and the touch controls

may not function while there is

liquid on them. Make sure you wipe

the touch control area dry before

turning the cooktop back on.

Hints and Tips

Problem Possible causes What to do

The induction hob

cannot be turned on.

No power. Make sure the induction hob is

connected to the power supply

and that it is switched on.

Check whether there is a power

outage in your home or area. If

you’ve checked everything and the

problem persists, call a qualified

technician.

The touch controls are

unresponsive.

The controls are locked. Unlock the controls. See section

‘Using your induction cooktop’ for

instructions.

16

The touch controls are

difficult to operate.

There may be a slight film of

water over the controls or you

may be using the tip of your

finger when touching the

controls.

Make sure the touch control area is

dry and use the ball of your finger

when touching the controls.

The glass is being

scratched.

Rough-edged cookware.

Unsuitable, abrasive scourer or

cleaning products being used.

Use cookware with flat and smooth

bases. See ‘Choosing the right

cookware’.

See ‘Care and cleaning’.

Some pans make

crackling or clicking

noises.

This may be caused by the

construction of your cookware

(layers of different metals

vibrating differently).

This is normal for cookware and

does not indicate a fault.

The induction hob

makes a low

humming noise when

used on a high heat

setting.

This is caused by the

technology

of induction cooking.

This is normal, but the noise should

quieten down or disappear

completely when you decrease the

heat setting.

Fan noise coming

from the induction

hob.

A cooling fan built into your

induction hob has come on to

prevent the electronics from

overheating. It may continue to

run even after you’ve turned

the

induction hob off.

This is normal and needs no action.

Do not switch the power to the

induction hob off at the wall while

the fan is running.

Pans do not become

hot and appears in

the display.

The induction hob cannot

detect the pan because it is not

suitable for induction cooking.

The induction hob cannot

detect the pan because it is too

small for the cooking zone or

not properly centred on it.

Use cookware suitable for induction

cooking. See section ‘Choosing the

right cookware’.

Centre the pan and make sure that

its base matches the size of the

cooking zone.

The induction hob or a

cooking zone has

turned itself off

unexpectedly, a tone

sounds and an error

code is displayed

(typically alternating

with one or two digits

in the cooking timer

display).

Technical fault. Please note down the error

letters and numbers, switch

the power to the induction hob

off at the wall, and contact a

qualified technician.

Never attempt to disassemble the unit by yourself.

17

Failure Display and Inspection

If an abnormality comes up, the induction hob will enter the protective state

automatically and display corresponding protective codes:

Problem Possible causes What to do

F3-F8 Temperature sensor failure Please contact the supplier.

F9-FE

Temperature sensor of the

IGBT failure.

Please contact the supplier.

E1/E2 Abnormal supply voltage Please inspect whether power

supply is normal.

Power on after the power

supply is normal.

E3/E4 Abnormal temperature Please inspect the pot.

E5/E6 Bad induction hob heat

radiation

Please restart after the

induction hob cools down.

The above are the judgment and inspection of common failures.

Please do not disassemble the unit by yourself to avoid any dangers and

damages to the induction hob.

Technical Specification

Cooking Hob CEICT2

Cooking Zones 2 Zones

Supply Voltage 220-240V~ 50Hz

Installed Electric Power 3500 W

Product Size D×W×H(mm) 288X520X56

Building-in Dimensions A×B (mm) 268X500

18

Weight and Dimensions are approximate. Because we continually strive to

improve our products we may change specifications and designs without prior

notice.

Installation

Selection of installation equipment

Cut out the work surface according to the sizes shown in the drawing.

For the purpose of installation and use, a minimum of 5 cm space shall be

preserved around the hole.

Be sure the thickness of the work surface is at least 30mm. Please select

heat-resistant work surface material to avoid larger deformation caused by the

heat radiation from the hotplate. As shown below:

Under any circumstances, make sure the Induction cooker hob is well ventilated

and the air inlet and outlet are not blocked. Ensure the Induction cooker hob is

in good work state. As shown below

Note: The safety distance between the hotplate and the cupboard above

the hotplate should be at least 760mm.

Air intake

mini 50mm

mini 760mm

mini 30m m

Air exit

mini 10 mm

26.8 cm

5cm mini

+0.4

-0

50 cm

+0.4

-0

5cm mini

19

Before you install the hob, make sure that

• the work surface is square and level, and no structural members interfere with

space requirements

• the work surface is made of a heat-resistant material

• if the hob is installed above an oven, the oven has a built-in cooling fan

• the installation will comply with all clearance requirements and applicable

standards and regulations

• a suitable isolating switch providing full disconnection from the mains power

supply is incorporated in the permanent wiring, mounted and positioned to

comply with the local wiring rules and regulations.

The isolating switch must be of an approved type and provide a 3 mm air gap

contact separation in all poles (or in all active [phase] conductors if the local

wiring rules allow for this variation of the requirements)

• the isolating switch will be easily accessible to the customer with the hob

installed

• you consult local building authorities and by-laws if in doubt regarding

installation

• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for

the wall surfaces surrounding the hob.

When you have installed the hob, make sure that

• the power supply cable is not accessible through cupboard doors or drawers

• there is adequate flow of fresh air from outside the cabinetry to the base of the

hob

• if the hob is installed above a drawer or cupboard space, a thermal protection

barrier is installed below the base of the hob

• the isolating switch is easily accessible by the customer

Before locating the fixing brackets

The unit should be placed on a stable, smooth surface (use the packaging). Do

not apply force onto the controls protruding from the hob.

Adjusting the bracket position

Fix the hob on the work surface by screw 4 brackets on the bottom of hob(see

picture) after installation.

Adjust the bracket position to suit for different table top thickness.

20

Cautions

1. The induction hotplate must be installed by qualified personnel or technicians.

We have professionals at your service. Please never conduct the operation by

yourself.

2. The hob will not be installed directly above a dishwasher, fridge, freezer,

washing machine or clothes dryer, as the humidity may damage the hob

electronics

3. The induction hotplate shall be installed such that better heat radiation can be

ensured to enhance its reliability.

4. The wall and induced heating zone above the table surface shall withstand

heat.

5. To avoid any damage, the sandwich layer and adhesive must be resistant to

heat.

Connecting the hob to the mains power supply

This hob must be connected to the mains power supply only by a suitably qualified

person.

Before connecting the hob to the mains power supply, check that:

1. the domestic wiring system is suitable for the power drawn by the hob.

2. the voltage corresponds to the value given in the rating plate

3. the power supply cable sections can withstand the load specified on the rating plate.

To connect the hob to the mains power supply, do not use adapters, reducers, or

branching

devices, as they can cause overheating and fire.

The power supply cable must not touch any hot parts and must be positioned so that its

temperature will not exceed 75C at any point.

Check with an electrician whether the domestic wiring system is suitable without

alterations. Any alterations must only be made by a qualified electrician.

The power supply should be connected in compliance with the relevant

standard,or a single-pole circuit breaker.the method of connection is shown

below.

La page charge ...

CONTINENTAL EDISON CEICT2 Manuel utilisateur

CONTINENTAL EDISON CEICT2 Manuel utilisateur

dans d''autres langues

Autres documents