Samsung DW80M9960US/AC Manuel utilisateur

Dishwasher

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

DW80M9* Series

DW9900M-00184B-00_EN.indd 1DW9900M-00184B-00_EN.indd 1 2016-12-12  2:51:172016-12-12  2:51:17

English - 2

contents

SETTING UP YOUR DISHWASHER

8

8 Unpacking your dishwasher

8 Checking parts

9 Meeting installation requirements

USING YOUR DISHWASHER

10

10 Control panel

12 Cycle selector

13 Basic guidelines

16 Samsung smart home (applicable models

only)

18 Adjusting the angle of the plate supports

19 Adjusting the height of the upper rack

19 Removing the upper rack

20 Loading the lower rack

20 Loading the upper rack

21 Using the 3

rd

(cutlery) rack (for some

models)

22 Using the cutlery rack

23 Using the glass support

23 Using the easy caddy (for some models)

23 using zone booster

24 Using detergent

25 Using rinse aid

CLEANING AND MAINTAINING YOUR

DISHWASHER

26

26 Cleaning the exterior

26 Cleaning the interior

27 Cleaning the nozzles

28 Cleaning the ﬁ lter

29 Cleaning the drain pump

29 Storing your dishwasher

CYCLES

30

30 Cycle chart

TROUBLESHOOTING

31

31 Check these points if your dishwasher…

34 Information codes

APPENDIX

35

35 Helping the environment

35 Speciﬁ cations

DW9900M-00184B-00_EN.indd 2DW9900M-00184B-00_EN.indd 2 2016-12-12  2:51:362016-12-12  2:51:36

English - 3

safety information

Congratulations on your new Samsung dishwasher. This manual contains important

information on the installation, use, and care of your appliance. Please take time to

read this manual to take full advantage of your washer’s many beneﬁ ts and features.

WHAT YOU NEED TO KNOW ABOUT THE SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all

possible conditions and situations that may occur. It is your responsibility to use

common sense, caution, and care when installing, maintaining, and operating

your washer.

IMPORTANT SAFETY INSTRUCTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

To reduce the risk of ﬁ re, explosion, electric shock, or personal injury when using

your dishwasher, follow these basic safety precautions:

CAUTION

Hazards or unsafe practices that may result in minor personal injury or property

damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

SAVE THESE INSTRUCTIONS

01 safety information

DW9900M-00184B-00_EN.indd 3DW9900M-00184B-00_EN.indd 3 2016-12-12  2:51:362016-12-12  2:51:36

English - 4

WARNING

State of California Proposition 65 Warning (US only)

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

WARNING: When using your dishwasher, follow basic precautions, including the following:

1. Read all instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Use only detergents or wetting agents recommended for use in a dishwasher and keep them

out of the reach of children.

4. When loading items to be washed:

- locate sharp items so that they are not likely to damage the door seal, and

- load sharp knives with the handles up to reduce the risk of cut-type injuries.

5. Do not wash plastic items unless they are marked "dishwasher safe" or the equivalent. For

plastic items not so marked, check the manufacturer’s recommendations.

6. Do not touch the HEATING ELEMENT during or immediately after use.

7. Do not operate your dishwasher unless all ENCLOSURE panels are properly in place.

8. Do not tamper with the controls.

9. Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

10. To reduce the risk of injury, do not allow children to play in or on the dishwasher.

11. Under certain conditions, hydrogen gas may be produced in a hot-water system that has

not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water

system has not been used for such a period, before using the dishwasher turn on all hot-

water faucets and let the water ﬂ ow from each for several minutes. This will release any

accumulated hydrogen gas. As the gas is ﬂ ammable, do not smoke or use an open ﬂ ame

during this time.

12. Remove the door to the washing compartment when removing an old dishwasher from

service or discarding it.

• After unpacking the dishwasher, keep the packaging out of the reach of children.

• The dishwasher is extremely heavy. Do not attempt to move or carry the dishwasher by

yourself. Two or more people are needed to move a dishwasher and avoid potential injuries.

• As with any equipment using electricity, water, and moving parts, potential hazards exist.

• Do not install the dishwasher near electrical components. Keep the dishwasher away from

open ﬂ ames.

• Install and level your dishwasher on an uncarpeted ﬂ oor that can support its weight.

• Your dishwasher must be properly grounded. Never connect it to an ungrounded outlet. See

page 9 for more information on grounding your dishwasher.

• Connect the ground wire to the green ground connector in the terminal box.

• After the dishwasher is installed, check that the drain hose is properly connected and

that there is no leakage from the hose connectors. If the drain hose is loose, it may cause

property damage.

• The water supply line is susceptible to breakage. As time goes by, it becomes less ﬂ exible.

Check the line periodically. If it is swollen, torn, cut, or there is a water leak, replace it

immediately.

WARNING

CAUTION

SAVE THESE INSTRUCTIONS

safety information

DW9900M-00184B-00_EN.indd 4DW9900M-00184B-00_EN.indd 4 2016-12-12  2:51:362016-12-12  2:51:36

English - 5

• To safely operate this appliance, familiarize yourself with its operations and exercise care

when using it.

• Do not put gasoline, solvents, or other ﬂammable materials inside the dishwasher. Do not

wash dishes exposed to these materials.

• Keep your dishwasher detergent out of the reach of children. Detergent has an adverse

e ect on human organs. It contains elements for polishing and is corrosive. Avoid letting the

detergent come into contact with your skin and eyes.

• Do not push or place pressure on the door when it is open, as this may damage the

dishwasher or cause harm.

• Do not allow children to play in or on the dishwasher. They may harm themselves or damage

the dishwasher.

• Disconnect the power cable (or set the circuit breaker to o ) before servicing your

dishwasher.

• Do not repair, replace, or service any part of your dishwasher yourself. Disassembly, repairs,

and modiﬁ cations are permitted by authorized service technicians only. Work done by an

unauthorized person may void your warranty.

• Before disposing of your dishwasher, remove the door of the washing compartment or the

door latch so that children or small animals cannot get trapped inside.

• If the dishwasher is left unused for an extended period of time, turn o the water supply.

• This dishwasher is intended for residential use only.

BEFORE USING YOUR DISHWASHER

WARNING

Tip-Over Hazard

- Do not use the dishwasher until it is correctly installed.

- Do not push down on the dishwasher door when it is open.

- Do not place excessive weight on the dishwasher door when it is open.

Electric Shock Hazard

Failure to follow these instructions can result in death, ﬁ re, or electric shock:

- Electrically ground the dishwasher

- Connect the ground wire to the green ground connector in the junction box.

- Do not use an extension cord.

WARNING

SAVE THESE INSTRUCTIONS

01 safety information

DW9900M-00184B-00_EN.indd 5DW9900M-00184B-00_EN.indd 5 2016-12-12  2:51:362016-12-12  2:51:36

English - 6

REGULATORY NOTICE

FCC Notice

FCC CAUTION:

Any changes or modiﬁ cations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of FCC Rules. Operation is Subject to following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received including interference that cause

undesired operation.

For products sold in the US and Canadian markets, only channels 1–11 are available. You

cannot select any other channels.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorienting or relocating the receiving antenna

• Increasing the separation between the equipment and receiver

• Connecting the equipment to an outlet that is on a di erent circuit than the radio or TV.

• Consulting the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated so there is at least 8 inches

(20cm) between the radiator and your body. This device and its antenna(s) must not be co-

located or operated in conjunction with any other antenna or transmitter.

CAUTION

safety information

SAVE THESE INSTRUCTIONS

DW9900M-00184B-00_EN.indd 6DW9900M-00184B-00_EN.indd 6 2016-12-12  2:51:372016-12-12  2:51:37

English - 7

IC Notice

The term “IC” before the radio certiﬁ cation number only signiﬁ es that Industry Canada technical

speciﬁ cations were met. Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

For products sold in the US and Canadian markets, only channels 1–11 are available. You

cannot select any other channels.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated so there is at least 8 inches

(20cm) between the radiator and your body. This device and its antenna(s) must not be co-

located or operated in conjunction with any other antenna or transmitter.

Open Source License Notice

The software included in this product contains open source software. You may obtain the

complete corresponding source code for a period of three years after the last shipment of this

product by sending an email to mailto:[email protected].

It is also possible to obtain the complete corresponding source code in a physical medium such

as a CD-ROM; a minimal charge will be required.

The following URL http://opensource.samsung.com/opensource/SimpleConnectTP/seq/0 leads

to the download page of the source code made available and open source license information as

related to this product. This o er is valid to anyone in receipt of this information.

SAVE THESE INSTRUCTIONS

01 safety information

DW9900M-00184B-00_EN.indd 7DW9900M-00184B-00_EN.indd 7 2016-12-12  2:51:372016-12-12  2:51:37

English - 8

setting up your dishwasher

Be sure to have your installer follow these instructions closely so that your new

dishwasher works properly and that you’re not at risk of injury when washing

dishes.

UNPACKING YOUR DISHWASHER

• Once your new dishwasher has been delivered to you, carefully unpack it and check for any damage.

If the dishwasher has been damaged, make note of it on the waybill and keep a copy.

Do not install the dishwasher, and contact Samsung Customer Service at the number listed below.

• If there is no damage to the product, you can proceed with the installation. If you are going to install it

yourself, make sure to read through the installation guide and follow the directions inside.

• After unpacking your dishwasher, keep the packaging out of the reach of children to ensure their safety.

CHECKING PARTS

When your dishwasher has been unpacked, make sure you’ve received all the parts shown below.

If your dishwasher was damaged during shipping, or if you do not have all the parts, contact Samsung

Customer Service at 1-800-SAMSUNG (726-7864).

Door

Base

Top nozzle

Dispenser

Lower nozzle

Water reﬂ ector

Control panel

Upper nozzle

Upper rack Lower rack Cutlery rack

3

rd

rack

(for some models)

3

rd

rack PAD

(for some models)

Easy Caddy

(for some models)

Accessory parts - User/Installation manual, Installation Kit, Kick Plate.

DW9900M-00184B-00_EN.indd 8DW9900M-00184B-00_EN.indd 8 2016-12-12  2:51:372016-12-12  2:51:37

English - 9

MEETING INSTALLATION REQUIREMENTS

Electrical supply and grounding

To prevent the risk of ﬁre, electric shock, or personal injury, all wiring and grounding must be

done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and

local codes and ordinances. It is the personal responsibility of the appliance owner to provide

adequate electrical service for this appliance.

Never use an extension cord.

When preparing for installation, ensure that your power supply provides:

• An individual 120 Volt, 60 Hz branch circuit serving only your dishwasher with a 15 AMP fuse

or circuit breaker.

Your dishwasher must be grounded. If your dishwasher malfunctions or breaks down, grounding

will reduce the risk of electric shock by providing a path of least resistance for the electric

current.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Grounding instructions

For a permanently connected appliance:

This appliance must be connected to a grounded metal, permanent wiring system, or an

equipment-grounding conductor must be run with the circuit conductors and then connected to

the equipment-grounding terminal or lead on the appliance.

Water supply

The hot water supply line pressure must be between 20-120 psi (140-830 kPa).

Adjust the water heater to deliver water between 120 ˚F (49 ˚C)-149 ˚F (65 ˚C).

Most plumbing supply stores sell water supply lines of various lengths up to 10 feet

(305cm) long.

You can reduce the risk of leaks and water damage by:

• Making water faucets easily accessible.

• Turning o faucets when the dishwasher is not in use.

• Periodically checking for leaks at water supply line ﬁttings.

Before using your dishwasher for the ﬁrst time, check all connections at the water supply valve

and faucets for leaks.

Flooring

For safety, your dishwasher must be installed on a solidly constructed ﬂ oor.

Never install your dishwasher on a platform or poorly supported structure.

Your dishwasher must be properly installed in accordance with the Installation Guide before you use it.

If you did not receive an Installation Guide with your dishwasher, you can obtain one by visiting our website

at www.samsung.com.

CAUTION

WARNING

02 setting up your dishwasher

DW9900M-00184B-00_EN.indd 9DW9900M-00184B-00_EN.indd 9 2016-12-12  2:51:392016-12-12  2:51:39

English - 10

using your dishwasher

WARNING: To reduce the risk of ﬁ re, electric shock, or injury to persons, read the IMPORTANT

SAFETY INSTRUCTIONS before operating this appliance.

CONTROL PANEL

DW80M99** Series

7 8 96 10321 4 5

DW80M95** Series

1

Power

When you press the Power button, the Cycle On light for the most recently started cycle turns

on. When the selected cycle is complete, the dishwasher powers o automatically.

2

Cycle Selector

Select the appropriate wash cycle depending on the soil level of your dishes. After you select a

cycle, the Cycle On light for that cycle lights.

If you want to change the cycle once it has started, press the Power button. Then, turn

on the dishwasher again and select a new cycle.

The default cycle is Normal.

3

Lower

When you select Lower (Lower Rack - Only), only the lower rack nozzle is activated. The upper

nozzle will not operate.

Use this feature to wash a small load of dishes or glasses placed in the lower rack.

When you select Lower (Lower Rack - Only), place items, glasses, etc. in the lower rack

only. The dishwasher will not wash items placed in the upper rack.

Selecting Lower (Lower Rack - Only) reduces both the cycle time and the amount of electricity

consumed.

If you want to wash heavily soiled items such as pots and pans, select the Zone Booster

option. (This option consumes slightly more water and energy.)

The Zone Booster option applies intensive washing power to the left part of the lower

rack.

Selecting the Zone Booster option does not turn o the Upper Nozzle.

4

Speed Booster Select this option to reduce washing time.

5

Hi-Temp Wash

Raises the main wash temperature to improve cleaning for loads containing tough, baked-on

food.

Hi-Temp Wash is not available for the Delicate and Rinse Only cycles.

WARNING

DW9900M-00184B-00_EN.indd 10DW9900M-00184B-00_EN.indd 10 2016-12-12  2:51:392016-12-12  2:51:39

English - 11

6

Sanitize /

( Control Lock)

With the Sanitize option selected, the water temperature is increased to 163˚F (73 ˚C) in the

ﬁ nal rinse cycle for high temperature sanitization.

If you select the Sanitize option, the "Sanitize" lamp blinks when the water temperature reaches

the sanitary temperature (over 155 ˚F (68 ˚C)), and then remains illuminated until the Sanitize

option ends. When you open the door or press the Power button, the "Sanitize" lamp turns o .

You cannot select the Sanitize option if you select the Delicate and Rinse Only cycles.

The Sanitize feature operates in accordance with NSF/ANSI Standard 184 for Residential

Dishwashers. Certiﬁ ed residential dishwashers are not intended for licensed food

establishments. Your dishwasher is NSF Certiﬁ ed.

Only the Heavy cycle with the Sanitize option has been designed to meet the requirements for

soil removal and sanitization e cacy in NSF 184.

Control Lock allows you to lock the buttons on the control panel so children cannot accidently

start the dishwasher by pressing the buttons on the panel.

To lock and unlock the buttons on the control panel, hold the Sanitize button down for three (3)

seconds when the power is On.

7

Display

Displays cycle time and remaining hours and minutes, Delay Start hours, and Information

codes. If a problem occurs during operation, an information code appears with a warning

sound. Refer to the information codes page.

Control Lock indicator

- Turns on if the Control Lock is set (or the dishwasher is in the standby or pause

modes).

- Turns o while the dishwasher is operating.

- When Control Lock is on, the Control Lock indicator blinks for several seconds if any

button except the Power button is pressed.

Self Clean indicator

- Turns on when the Self Clean option is enabled (or the dishwasher is in the standby

or pause modes), but turns o while the dishwasher is operating.

- Blinks for 5 seconds every 20 to 22 cycles.

- The cycle counter disappears when the Self Clean operation is complete or when

the dishwasher reaches the 23rd cycle without the Self Clean cycle being used.

(The Cancel or Self Clean operation is not counted by the cycle counter.)

Rinse Reﬁ ll indicator

- Turns on if the dishwasher runs out of rinse aid (or the dishwasher is in the standby

or pause modes).

- Turns o while the dishwasher is operating.

8

Delay Start

Delay a cycle for up to 24 hours in one-hour increments. To increase the delay start time, press

or hold the Delay Start button. The hour displayed indicates the time at which the wash will

start.

- After setting the delay time, press the Start button, and then close the door to start the

cycle.

- If you want to change the delay time once the dishwasher has started, press the Cancel

button and turn o the dishwasher. Then, turn on the dishwasher again and select a new

cycle with a new delay setting.

9

Smart Control

To connect the dishwasher to your smart phone, use this option.

For details, see page 16.

To connect the dishwasher to your smart phone the ﬁ rst time. press and hold

Smart Control to start the AP mode in the dishwasher.

03 using your dishwasher

DW9900M-00184B-00_EN.indd 11DW9900M-00184B-00_EN.indd 11 2016-12-12  2:51:392016-12-12  2:51:39

English - 12

10

Start

To start a cycle, press the Start button before closing the door.

*Cancel: To cancel a currently running cycle and drain the dishwasher, press and hold the Start

button for three (3) seconds.

Once the dishwasher is reset, select a cycle and option, and then press Start to restart the

dishwasher.

You can select options (Self Clean, Lower, Speed Booster, Zone Booster, Sanitize, Delay Start) before

starting a cycle. If you change the cycle after selecting an option, the original cycle is reset.

When you pause a cycle by opening the door during operation, press the Start button before closing

the door to continue the cycle.

Push the door closed ﬁ rmly within 3 seconds of pressing the Start button.

If the door is not closed within 3 seconds, the cycle will not start.

To prevent the touchpad from losing response sensitivity, follow these instructions:

- Touch the center of each keypad using one ﬁ nger. Do not push.

- Clean the touch control’s surface regularly with a soft, damp cloth.

- Be careful not to touch more than one touch key pad at a time, except as directed.

OO X

CYCLE SELECTOR

1 2 3 4 5 6 7

1

Auto

This cycle detects the level of soil and automatically initiates the optimal cycle after a few

minutes of operation.

2

Normal

Use this cycle for normally soiled dishes.

The energy-usage label is based on this cycle.

3

Heavy Use this cycle for heavily soiled dishes.

4

Delicate

Use this cycle for soiled, fragile items such as ﬁ ne glassware and crystal glass (wine glass). Do

not use this cycle for other glassware because clouding or etching may occur.

The Zone Booster and Sanitize options are not available with this cycle.

5

Express 60

Use this cycle when you need to wash dishes quickly. It takes about 1 hour.

You cannot select the Speed Booster or Zone Booster option if you select this cycle.

6

Rinse Only

Use for rinsing dishes, glasses, and silverware that will not be washed right away. Do not use

detergent.

7

Self Clean

Use the Self Clean function to clean the dishwasher's tub. If the dishwasher needs self cleaning,

the Self Clean indicator will blink for 5 seconds when you turn the power on. If you start the

dishwasher when the indicator is blinking, the indicator will turn o automatically. Always run the

Self Clean cycle with the dishwasher empty. Never use it as a Normal cycle to clean dishes.

using your dishwasher

DW9900M-00184B-00_EN.indd 12DW9900M-00184B-00_EN.indd 12 2016-12-12  2:51:402016-12-12  2:51:40

English - 13

BASIC GUIDELINES

1. Open the door and load your dishes (see page 20-22).

- Place dishes into the upper and lower racks, unless you have selected the

Lower (Lower Rack - Only) option.

- Remove any food remains from the dishes before placing them in the rack(s).

- After placing the dishes into the racks, turn the upper nozzles to make sure none of the dishes will

block nozzle rotation.

- Make sure the dishes will not prevent the detergent dispenser from opening.

2. Add detergent to the dispenser (see page 24).

- Make sure to use only automatic dishwasher detergent.

- Refer to "Using detergent" on how to add detergent.

3. Press the Power button.

- When you press the Power button, the cycle light of the most recently started cycle lights up.

- If "Rinse Reﬁ ll" Indicator is illuminated, you should reﬁ ll the rinse aid dispenser to improve washing

and drying performance.

4.

Select an appropriate cleaning cycle depending on the soil level of the dishes. (see pages 12 and 30).

- Press the appropriate Cycle button.

- When you press a Cycle button, the cycle indicator light is illuminated.

- For information about selecting a cycle according to the soil level of the dishes, see "Cycle

selector".

5. Press the Start button, and then close the door.

- Push the racks back so that they are in place, and then press the Start button and close the door.

- Make sure to close the door ﬁ rmly. If the door is slightly ajar, the selected cycle will not start

automatically.

- The dishwasher will start draining after a few seconds, and then start the cycle you selected.

6. When the wash cycle is completed.

- Power is automatically turned o after one minute.

If you want to load more dishes or pause the dishwasher while it is already running, make sure to open

the door slowly and carefully as there is a possibility of injury from the hot steam or water inside the

dishwasher.

(If the door is opened while the dishwasher is running, a safety mechanism is activated that stops the

cycle.) To resume operation, press the Start button, and then close the door.

Note that adding dishes several minutes after the dishwasher started operating may a ect the

performance.

You should use rinse aids for better drying performance. You can further improve drying performance

by also selecting the Sanitize option.

CAUTION

03 using your dishwasher

DW9900M-00184B-00_EN.indd 13DW9900M-00184B-00_EN.indd 13 2016-12-12  2:51:412016-12-12  2:51:41

English - 14

Touch Controls

Touch controls allow you to operate the dishwasher easily.

• They are convenient to operate, requiring only a soft touch.

• Have a simple and stylish design.

• Are easy to clean.

If you have children or you want to clean the Control Interface, we recommend activating

the Control Lock feature to lock the control buttons.

- Children will not be able to accidently start the dishwasher by touching the controls with

this option selected.

- If a cycle is running, the buttons will not respond. (except the Power button and

Control Lock & Cancel options)

- If the dishwasher is o , only the Power button responds.

Delay Start

When you select the Delay Start option, your dishwasher will begin the selected cycle when the

delay time expires.

The Water Reﬂ ector Interference Signal:

• The water reﬂ ector interference feature automatically detects obstacles in the tub. If it detects

an obstacle, the display blinks and the dishwasher chimes for several minutes. If an obstacle

is detected at the end a cycle, "0" blinks for several minutes.

• Remove any obstacles in the bottom of the dishwasher.

Auto Release™

The Auto Release™ Dry function, which is designed to improve drying performance,

automatically opens the dishwasher's door 5 to 15 minutes before a cycle ends.

You can enable or disable Auto Release™ Dry in two ways: Using the Setting Mode or using the

toggle keys. Both methods are described starting below.

Auto Release™ On/O

Using Setting Mode

• To enter Setting mode, press the Delay Start + Sanitize buttons for 3 seconds while the

dishwasher is on.

• Press the Sanitize button until "A1" or "A0" is displayed. "A0" disables Auto Release™ Dry.

"A1" enables Auto Release™ Dry. Select "A1" for better drying results.

• Press the Delay Start button to implement your choice.

using your dishwasher

DW9900M-00184B-00_EN.indd 14DW9900M-00184B-00_EN.indd 14 2016-12-12  2:51:412016-12-12  2:51:41

English - 15

Using the Toggle keys

• Press the Lower + Hi-Temp Wash

button for 3 seconds to enable or disable

Auto Release™ Dry.

* "A0" disables Auto Release™ Dry.

"A1" activates Auto Release™ Dry.

More About Auto Release Dry

* Once the door opens in the

Auto Release™ Dry mode, the door

cannot be closed manually for the next

2minutes.

* The Auto Release™ Dry mode will be

disabled for the Rinse Only cycle.

Changing the "Auto Release™ Dry" setting can inﬂ uence drying results. Select "A1" mode

for better drying results. ("A1" is the default setting.)

After a cycle is complete, the door automatically opens to let steam out. This is normal and

not a product malfunction.

Setting Mode

The Setting Mode lets you change the dishwasher's sound setting and LED brightness setting.

To enter the Setting mode, press the Delay Start + Sanitize buttons for 3 seconds while the

dishwasher is on. Press the Sanitize button to select a sub-setting menu, and then press the

Delay Start button to change a setting.

- Sound Setting: Press the Sanitize button until "U1" or " U0" is displayed. To change the

setting, press the Delay Start button. "U0" means that the sound is o for all cycles. The

dishwasher maintains the Sound Setting you have selected until you change it.

- Pocket LED Brightness Setting: Press the Sanitize button until "B0-B5" is displayed.

The higher the number, the brighter the LEDs. To change the setting on the dishwasher,

press the Delay Start button.

When using the dishwasher, try to arrange the dishes properly as described on page 20.

• You should remove food remains such as bones, fruit seeds, etc. and any other waste such

as toothpicks, paper, etc. from the dishes as these may cause damage to the dishes, create

noise, or cause the dishwasher to malfunction.

• Select the appropriate cycle depending on the level of soil and the type of dishes.

• Use only the proper amount of detergent and rinsing agent.

Do not wash the following items in your dishwasher.

• Acrylic or Aluminum items: Acrylic and aluminum items can discolor dishes with printed

gold rim decoration and mar other items.

• Dishes treated with adhesive: Treated plastics can come apart. Wood, ivory, copper, and

tin glued to dishes can come loose.

• Plastics with a temperature tolerance less than 194 ˚F (90 ˚C): Thin plastics wash and dry

poorly, and may be damaged by elevated wash temperatures.

• Tin: Tin should be washed by hand and dried immediately as it can rust.

• Wooden utensils: Wooden items can crack.

WARNING

03 using your dishwasher

DW9900M-00184B-00_EN.indd 15DW9900M-00184B-00_EN.indd 15 2016-12-12  2:51:412016-12-12  2:51:41

English - 16

SAMSUNG SMART HOME (APPLICABLE MODELS ONLY)

Installation

Visit the Google Play Store, Galaxy Apps, or Apple App Store and search for “Samsung Smart

Home”. Download and install the Samsung Smart Home app provided by Samsung Electronics

to your smart device.

The Samsung Smart Home app is designed for Android 4.0 (ICS) or higher, or iOS 7.0 or

higher, and is optimized for Samsung smartphones (Galaxy S and Galaxy Note series).

On other smartphone models, some functions may operate di erently.

For improved performance, the Samsung Smart Home app is subject to change

without notice. App support can also be discontinued without notice according to the

manufacturer’s policy.

Samsung account

You must have a registered Samsung account to use the app. If you don’t have a Samsung

account, follow the app’s on-screen instructions to create a free Samsung account.

Getting started

For Android smartphone users

1. Run the Samsung Smart Home App on your smartphone.

2. Tap Add Device > Select other device > Dish Washer

on the app screen.

3. Press and hold Smart Control on the dishwasher’s

control panel for more than 3 seconds.

4. Wait while the app scans for available network

connections and ﬁ nds your network (AP).

5. Tap your AP, and then input your network password.

6. When the device registration is complete, tap Done. Now

you can control your dishwasher remotely.

using your dishwasher

DW9900M-00184B-00_EN.indd 16DW9900M-00184B-00_EN.indd 16 2016-12-12  2:51:412016-12-12  2:51:41

English - 17

For iOS smartphone users

1. Run the Samsung Smart Home App on your iPhone, and

then tap Add Device.

2. Log in using your Samsung account ID and password.

Tap Select other device > Dish Washer.

3. Press and hold Smart Control on the dishwasher’s

control panel for more than 3 seconds. Tap Next.

4. Follow the onscreen instructions, and then go to

Settings. Tap Wi-Fi > [Dish Washer] Samsung Wi-Fi,

and then input the password, ‘1111122222’.

5. Back on the app screen, tap Next. When the app ﬁ nds

your network (AP), input the network password.

6. Follow the onscreen instructions, and then go to Settings

again. Tap the connected AP. Back on the app screen,

tap Next.

7. When the device registration is complete, tap Done. Now

you can control your dishwasher remotely.

If the Smart Control function is activated, the Smart Control indicator on the door lights up

accordingly.

This product is a smart dishwasher that supports the Samsung

Smart Home service.

For more information, visit www.samsung.com.

Key features

Register Samsung smart home appliances to the Samsung Smart Home server for remote

access.

Menu overview

1

2

3

4

5

6

7 8

03 using your dishwasher

DW9900M-00184B-00_EN.indd 17DW9900M-00184B-00_EN.indd 17 2016-12-12  2:51:412016-12-12  2:51:41

English - 18

For improved performance, the content and design of the app is subject to change without

notice.

1

Current cycle Tap to select a desired cycle.

2

Start/Pause

With Smart Control enabled on the dishwasher, you can Start or

Pause operation temporarily using your smart phone.

3

Options

Set or adjust the options as necessary. You can ﬁ nd an

explanation of each option in the Control panel explanation.

4

Current Process The currently running process of the selected cycle is displayed.

5

Time Progress The time progress for the selected cycle is displayed.

6

Estimated

Finish Time

The estimated ﬁ nish time is displayed.

7

Cancel

Tap to cancel the current cycle and return to the cycle selection

screen.

8

Cancel & Drain

Tap to cancel the current cycle, drain the water from the

dishwasher, and return to the cycle selection screen.

ADJUSTING THE ANGLE OF THE PLATE SUPPORTS

You can adjust the angle of the tines in the upper rack to three di erent positions to match the size and

shape of your dishes. To adjust the tines, grasp the handle at the front of the rack, and then push it left or

right. See the illustration below.

In the lower rack, you can easily fold down the fold-down tines to make room for large items such as pots

and pans. Remove the rack from the dishwasher, and then fold down the tines one at a time. See the

illustration below.

Upper rack Lower rack

using your dishwasher

DW9900M-00184B-00_EN.indd 18DW9900M-00184B-00_EN.indd 18 2016-12-12  2:51:422016-12-12  2:51:42

English - 19

ADJUSTING THE HEIGHT OF THE UPPER RACK

You can adjust the height of the upper rack in your Samsung dishwasher so that the lower rack can

accommodate larger sized dishes. Depending on where you set the upper rack height, the lower rack can

accommodate plates up to 12 in. (30 cm) in diameter and the upper rack can accommodated plates up to

8 in. (20 cm) in diameter.

1. To lower the upper rack by 2 in. (5 cm), pull the

adjust handles located at the left and right sides

of the upper rack, and then push the upper rack

downwards slightly at the same time.

2. To raise the upper rack, just pull the upper rack

upwards. The adjuster handle will latch and the

upper rack will move to the high position.

We recommend adjusting the height of the upper

rack before loading dishes into the rack. If you

adjust the the rack after loading the dishes, you

may damage the dishes. If you do not adjust with

left and right handle together, the dishwasher

door may not close properly.

Pull out the upper rack from the tub until it is fully

revealed before adjusting the upper rack.

REMOVING THE UPPER RACK

Pull the upper rack towards the front and then remove it by lifting it up slightly and pulling it towards the

front. See the illustrations below.

While the upper rack is removable, it must be installed for the dishwasher to operate properly.

If you attempt to operate the dishwasher without the rack, noise will occur and the dishwasher will

perform poorly.

Step 1. Step 2. Step 3.

CAUTION

03 using your dishwasher

DW9900M-00184B-00_EN.indd 19DW9900M-00184B-00_EN.indd 19 2016-12-12  2:51:422016-12-12  2:51:42

English - 20

LOADING THE LOWER RACK

The lower rack has been especially designed for dinner dishes, soup bowls, plates, pots, lids, casserole

dishes, and plates.

Load large items such as pans and pots into the dishwasher so their open sides face downwards. We

recommend loading cups, stemware, and small plates into the upper rack.

See the recommended loading patterns below.

Dessert plate

10 place setting 12 place setting

LOADING THE UPPER RACK

The upper rack has been designed for small plates, mugs, glasses, and plastic items marked “dishwasher

safe”. Load your plates into the dishwasher in two half rows, so that the front of each plate faces the back of

the plate in front of it, and the open sides of the plates at the center of the dishwasher face each other. See

the illustrations below.

Make sure the loaded dishes do not interfere with the rotation of the nozzle which is located at the bottom

of the upper rack. (Check this by rotating the nozzle by hand.)

When loading dishes, pull the upper rack out su ciently so you can load it without striking the counter

above.

10 place setting 12 place setting

using your dishwasher

DW9900M-00184B-00_EN.indd 20DW9900M-00184B-00_EN.indd 20 2016-12-12  2:51:432016-12-12  2:51:43

La page est en cours de chargement...

Samsung DW80M9960US/AC Manuel utilisateur

Ce manuel convient également à

Samsung DW80M9960US/AC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents