Uniden PRO505XL Guide d'installation
- Catégorie
- Radios bidirectionnelles
- Taper
- Guide d'installation
PRO505XL
Professional Mobile CB Radio
© 2015 Uniden America Corp. Printed in Vietnam
Irving, Texas U01UT386ZZA(0)
2
Welcome to the world of Citizens Band radio communications. Your
Uniden radio is an advanced mobile radio designed for use in the
Citizens Band (CB) Radio Service. It will operate on any of the 40 AM
frequencies authorized by the Federal Communications Commission
(FCC). Your Radio features a superheterodyne circuit with PHASE
LOCKED LOOP techniques to assure precise frequency control.
Safety Notice
The antenna used for this radio must be properly installed and
maintained and must provide a separation distance of at least 16.92
inches (43 cm) from all persons and must not be collocated or operated
in conjunction with any other antenna or transmitter. Never transmit if
any person is closer than the specied distance to the antenna.
Note that Uniden does not specify or supply any antenna with
this transceiver. While a 0 dBi gain antenna is normal for a typical
installation, the above limit applies to any antenna with up to 3 dBi gain.
CB license requirement
U.S. users no longer need to apply for a license to use a CB radio.
However, CB radio is still considered a “license by rule” service. This
means that, while the FCC permits CB station operation without station
identication, station operators are still required to comply with the
Communications Act and with the rules of CB Radio Service. (For more
information on U.S. radio rules, visit the FCC website at www.fcc.gov.)
Uniden contact information
You can get answers 24/7 at our website: www.uniden.com.
If any of these items are missing or damaged, immediately contact your
place of purchase or Uniden’s Parts Department.
INTRODUCTION
INCLUDED IN YOUR PACKAGE
3
PRO505XL Mobile radio
Microphone and hook
Mounting bracket, knobs, and mounting hardware
► Other printed materials
NOTE: You must use a CB antenna (sold separately) with this radio.
Front
No. Name Details
1 CB/PA
Switch
Switches between CB Radio and PA systems
2 Volume/
Power
Adjusts the volume.
Turns radio on and off.
3 4-Pin Mic Plugs in microphone
4 CH9 Sets the radio to CH9 (Emergency).
5, 6 Channel
Selectors
Press or to select which channel the radio
will transmit or receive on.
7 Squelch
knob
Adjusts the level at which the radio squelches or
suppresses weak radio signals
PARTS OF THE RADIO
1
4
3
2
765
4
NOTE: FCC rules reserve Channel 9 for motorist assistance and
other emergency communications. Channel 9 should only be used
in situations where there is immediate danger to the safety of
individuals or the protection of property.
Back
No. Name Details
8 Antenna
Connector
Connects to a male PL-259 external antenna
cable (antenna sold separately).
9 PA Speaker
Jack
See Connecting external speakers, page 6.
10 External
Speaker Jack
See Connecting external speakers, page 6.
11 12 Volt DC
Power Cord
Connects to DC power supply, page 4.
Microphone
Press and hold the PTT button to transmit on
the selected channel. Release the button to listen
for a response.
NOTE: For the best sound quality, hold the
microphone about 2 inches away from your
mouth and speak in a normal voice.
NOTE: Make sure you have read and understood part 95 of the FCC
rules and regulations before using the transmitter.
Connect the microphone
Align the microphone connector with the jack on the front of the radio.
Push the connector in rmly and secure it with the locking screw.
Connect the power
You can connect the radio to any standard 12 volt DC power source,
8
10
9
11
Push-to-Talk
button
INSTALLATION
5
with either a positive or negative ground. If you don’t know whether
your power supply uses a positive or negative ground, consult the
manual for your power supply or contact the manufacturer.
WARNING! DO NOT connect this equipment to a power supply if you
are not absolutely certain of the grounding type!
1) Make sure your power supply is turned off.
2) For power supplies with a NEGATIVE ground, connect the RED
lead on the radio to the power supply’s POSITIVE (+) pole, and
connect the BLACK lead to the power supply’s NEGATIVE (–) pole
or to a neutral ground such as the chassis.
Turn on your power supply.
3) Turn the radio’s Volume knob clockwise to power on the radio.
Installing the mounting bracket
When choosing the location for the radio’s mounting bracket, keep the
following things in mind:
► Pick a location that does not block your view, interfere with your
vehicle’s controls, or hinder your driving.
► Make sure the radio and microphone are not in front of an airbag.
► Pick a solid surface that can support the bracket and radio weight.
► Make sure there’s enough room. (You may want to put the radio in
the bracket when you’re choosing where to install the bracket.)
Once you choose the location, use the included, self-tapping screws
to attach the mounting bracket and the microphone bracket to your
vehicle (you don’t have to drill holes). Slide the radio into the bracket
and use the included knobs to hold it at the preferred angle.
Connecting an external antenna
WARNING! The antenna used for this radio must be installed at least
16.92 inches (43 cm) away from all persons. The antenna must not
be collocated or used with any other antenna or transmitter.
CAUTION: Never operate your radio with no antenna or with a
damaged antenna cable. This can damage the radio.
You will need to purchase an antenna to operate the radio. There are
two basic types of mobile CB antennas–full-length whips and loaded
whips–with a wide variety of mounts to suit different vehicle locations.
► Choose an antenna that matches the specications of this radio.
► Follow the manufacturer’s installation instructions carefully.
6
► Tune your antenna using a Standing-Wave Ratio (SWR) meter: set
the radio to channel 20, and adjust the antenna until the SWR is as
close as 1:1 as possible.
Connecting external speakers
Your radio supports two external speakers for remote monitoring and
public address features. External speakers are sold separately.
To prevent feedback, direct all speakers away from the microphone.
External monitor PA speaker
Function Remote receiver
monitoring or substitution
for internal speaker
Public address broadcasts
Impedance 8 Ohms 8 Ohms
Rating 3 Watts 3 Watts
Connect to EXT.SP. jack (⅛-in/3.5
mm)
PA.SP. jack (⅛-in/3.5 mm)
Notes The internal speaker is
disabled when an external
speaker is connected.
You must have a PA
speaker connected to use
the PA feature.
CAUTION: Make sure the SWR is less than 2:1 before using the
radio. An SWR higher than 2:1 can damage the transmitter.
Your Uniden dealer can help you select the antenna that is best for your
needs. Consult the specications in the back of this manual for detailed
transmitter and antenna information.
Basic operation
Turning the
radio on
Turn the Volume knob clockwise until the display
backlight comes on.
Turning the
radio off
Turn the Volume knob counter-clockwise until it
clicks and the display backlight turns off.
Selecting a
channel
Press or buttons to select a channel.
Changing the
volume
Turn the Volume knob clockwise to increase the
volume; turn it counter-clockwise to decrease the
volume.
OPERATION AND MAINTENANCE
7
Transmitting
– Tune the radio to the channel you want to transmit
on, and listen to make sure the channel is clear.
– Press and hold the PTT button.
– Hold the microphone about 2 inches away from
your mouth and speak in a normal voice.
– Release the button to listen for a response.
Using the PA
feature
– Toggle the CB/PA switch to PA; this turns off the
CB radio and activates the PA speaker.
– On the microphone, press and hold the PTT
button.
– Hold the microphone about 2 inches away from
your mouth and speak in a normal voice. Use
the Volume knob to adjust the volume of the PA
speaker.
– When you’re nished broadcasting, release the
button and move the CB/PA switch back to CB.
Adjusting the
squelch level
– To lter out weaker signals and background noise,
turn the knob clockwise to increase the squelch
level.
– To decrease the squelch level so you can hear
weaker radio signals, turn the knob counter-
clockwise.
Using the
Instant
Channel 9
feature
– Press the CH9 button; the radio automatically
tunes to channel 9.
– Press the CH9 button again to return to the
previous channel.
NOTE: Make sure you read and understood part 95 of the FCC rules
and regulations before using the transmitter.
Maintenance
Every six to twelve months, check to make sure that:
► The Voltage Standing Wave Ratio (VSWR) is less than 2:1.
► All electrical connections are secure and free of corrosion.
► The antenna cable shows no wear or damage.
► All mounting screws are securely fastened.
4. Inspect all screws and other mounting hardware.
If your radio is not performing to your expectations, please try these
simple steps. If these steps don’t solve your problem, visit www.uniden.
com for help.
TROUBLESHOOTING
8
Problem: Things to try:
Radio won’t
turn on (no
power)
1. Check the radio’s power cord and all connections.
2. Check the fuse in the radio’s power cord.
3. Check your vehicle’s electrical system.
Poor reception
1. Adjust the squelch level.
2. Check the antenna, cable and connectors.
3. Check operation mode of the radio.
Background
noise
1. Adjust the squelch level.
Weak
transmission
1. Check the antenna, cable and connectors.
2. Check the antenna grounding.
3. Check for corrosion on the connectors.
PA won’t
broadcast
1. Check the CB/PA toggle is set to PA.
2. Check the mike’s PTT button is pressed in when
you talk.
Service and repair information
► Service, repair, or alignment should only be attempted by a qualied
and/or licensed radio technician.
► When ordering parts, it is important to specify the correct model
number of this radio.
► It is the user’s responsibility to make sure the radio is operating in
accordance with the FCC Citizens Radio Service regulations at all
times.
General
Channels 40 AM
Frequency Range 26.965 to 27.405 MHz
Frequency Control Phase Locked Loop (PLL) synthesizer
Frequency
Tolerance
±0.005%
Operating
Temperature
-30ºC to +50ºC
Microphone Plug in type, electret
Input Voltage 13.8 V DC nom. (+ or - ground)
Current Drain TX full mod., 1.4A
RX with max. audio output, 0.8A
Size 4-7/8” W x 7-1/2” D x 1-3/4” H
SPECIFICATIONS
9
Weight 1 lb. 3 oz.
Antenna Connector UHF, SO-239
LCD Meter Indicates relative RF output and received
signal strength
TransmiTTer
Power Output 4 Watts
Modulation Class B amplitude modulation
Freq. Response 300-2500 Hz
Output Impedance 50 ohms, unbalanced
receiver
Sensitivity 0.8μV for 10 dB; (S + N) /N typical (limit 1.6μV)
Selectivity 6 dB @ 7kHz, 70 dB @ 10kHz typical
Image Rejection 65 dB typical
I.F. Frequency Double Conversion Superheterodyne
1st 10.692 MHz
2nd 450 kHz
Automatic Gain
Control (AGC)
less than 10dB change in audio output for
inputs from 10 to 50,000 microvolts
Squelch Adjustable; threshold less than 1.25μV
Audio Output
Power
3 watts max. into 8 ohms
Freq. Response 300 to 2000 Hz
Distortion less than 10% at 0.5 watts, 1000Hz
Internal Speaker 8 ohms, 2 watts round
Specications and features are subject to change without notice.
FCC PART 15 & IC COMPLIANCE INFORMATION
FCC Compliance Statement: This device complies with Part 15 of the FCC rules.
Operation is subjected to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s).Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Changes or modications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15
des règlements de la Commission fédérale des communications (FCC). Ce dispositif
est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences
10
nuisibles et; 2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites
pouvant nuire à son fonctionnement.
Cet appareil est conforme aux normes RSS exemptes de licences d’Industrie Canada.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit
pas causer d’interférences nuisibles et (2), il doit pouvoir accepter les interférences,
incluant celles pouvant nuire à son fonctionnement normal.
Tout changement ou modication non approuvé expressément par la partie
responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet équipement.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail
owner, this Uniden Product to be free from defects in materials and craftsmanship with
only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be
of no further effect 12 months after the date of original retail sale. The warranty is
invalid if the Product is (A) damaged or not maintained as reasonable or necessary,
(B) modied, altered, or used as part of any conversion kits, subassemblies, or any
congurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction with equipment or parts or as part
of any system not manufactured by Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, warrantor will either, at its option,
repair or replace the defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling) incurred by warrantor or
its representatives in connection with the performance of this warranty. Warrantor,
at its option, may replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR
THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, and you may also
have other rights which vary from state to state. This warranty is void outside the United
States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following
the instructions in the owner’s manual you are certain that the Product is defective,
pack the Product carefully (preferably in its original packaging). The Product should
include all parts and accessories originally packaged with the Product. Include
ONE-YEAR LIMITED WARRANTY
11
evidence of original purchase and a note describing the defect that has caused you
to return it. The product should be shipped freight prepaid, by traceable means, to
warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76262
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Uniden PRO505XL Guide d'installation
- Catégorie
- Radios bidirectionnelles
- Taper
- Guide d'installation
dans d''autres langues
- English: Uniden PRO505XL Installation guide
Documents connexes
-
Uniden PRO510XL Le manuel du propriétaire
-
Petra PRO401HH Manuel utilisateur
-
Uniden ATLANTIS 155 Le manuel du propriétaire
-
Uniden AMWUT653 Manuel utilisateur
-
-
Uniden GMR3050-2C Le manuel du propriétaire
-
Uniden SX237 Le manuel du propriétaire
-
Uniden GMR2035-2 Le manuel du propriétaire
-
-
