MarkBass Super Synth Le manuel du propriétaire

MarkBass
Marque
MarkBass
Modèle
Super Synth
Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire
owner’s manual
v. 24.july.2015
02
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions;
2) Keep these instructions;
3) Heed all warnings;
4) Follow all instructions;
5) Do not use this apparatus near water;
6) Clean only with dry cloth;
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions;
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat;
9) Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not t into
your outlet, consult an electrician for replacement of the obsolete outlet;
10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus;
11) Only use attachments/accessories specied by the manufacturer;
12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from the tip-over (and Fig 21 DU Tipping Cart Symbol).
13) Unplug this apparatus during lightning storms or when unused for long periods of time;
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped;
15) “Warning: to reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture; and
objects lled with liquids, such as vases, should not be placed on this apparatus”;
16) To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from
the AC receptacle;
17) The mains plug of the power supply cord shall reamin readily accessible.
18) In case of voltage selector make sure the switch on the rear panel is on the correct voltage before
connecting it to the AC power, and the fuse is the right value for that voltage (This selector is not available
on the 100V version). Please change the voltage/fuse values label located near the voltage selector
matching the voltage/fuse values when you need to change the voltage of the apparatus.
19) “WARNING: this apparatus must be securely attached to the oor or wall in accordance with
installation istruction. Tipping, shaking, or rocking the machine may cause injury or death.”
PRÉCAUTIONS D’EMPLOI
1) Lire ces instructions;
2) Conserver ces instructions;
3) Suivre tous les conseils d’utilisations;
4) Suivre toutes les instructions;
5) Ne pas utiliser cet appareil au bord de l’eau;
6) Nettoyer uniquement avec un chion humide;
7) Ne pas bloquer le système de ventilation. Installer conformément aux instructions du fabricant;
8) Ne pas installer l’appareil près d’une source de chaleur tel qu’un radiateur, un fourneau, ou bien un autre
appareil qui produit de la chaleur;
9) Ne pas modier le système de sécurité de la che polarisée ou de de la che pour les prises de terre. Une
che polarisée a deux broches, l’une étant plus distante de l’autre. Une che pour prise de terre a deux
broches et une pointe pour la masse. La broche plus distante et la pointe pour la masse ont été installées
pour votre sécurité. Si la che fournie de rentre pas dans votre prise de courant consulter un électricien pour
la substitution;
10) Protéger le cordon d’alimentation an qu’il ne soit pas piétiné ou écrasé tout particulièrement au niveau des
ches, des prises de courant femelles, et des parties qui sortent de l’appareil;
11) Utiliser uniquement les accessoires recommendés par le fabricant;
12) Utilisez uniquement avec le chariot, le socle, le trépied, le support ou la table spéciés par le fabricant ou
vendu avec l’appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous déplacez l’ensemble cha
riot / appareil pour éviter toute blessure du renversement (et la gure 21 DU Tipping panier Symbol).
13) Ne pas branché l’appareil en cas d’orage accompagné d’éclairs. Le débrancher en cas de non utilisation pro
longée;
14) S’adresser à un service assistance agréé si l’appareil a subi des dommages, si le cordon d’alimentation ou la
che a été endommagé, si un liquide a été renversé sur l’appareil ou bien si un object est tombé dans
l’appareil, si ce dernier a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas correctement ou s’il est
tombé;
15) “Avertissant: pour réduire le risque du feu ou de décharge électrique, n’exposez pas cet appareil à la pluie ou
l’humidité et les objets remplis de liquides; tels que des vases, ne devraient pas être placés sur cet appareil”;
16) Pour déconnecter totalement cet appareil du secteur, débranchez la cordon d’alimentation che de la prise
secteur;
17) La prise de courant doit être facilement accessible.
18) En cas de sélecteur de tension s’assurer que l’interrupteur sur le panneau arrière est sur la bonne tension
avant de le raccorder à l’alimentation secteur et le fusible est la bonne valeur pour que la tension
(Ce sélecteur n’est pas disponible sur la version 100V). S’il vous plaît changer la tension / valeurs de fusibles
étiquette située près du sélecteur de tension correspondant aux valeurs /fusibles de tension lorsque vous
avez besoin de changer la tension de l’appareil.
19) “AVERTISSEMENT: cet appareil doit être assujetti au plancher ou au mur conformément aux instructions
d’installation. Le fait de l’incliner, de le balancer ou de l’agiter peut causer des blessures ou la mort.”
MORE INFORMATION
For warranty and service information, please contact your local Markbass distributor (contact information available at www.markbass.it). For more technical information, please visit us at www.markbass.it and ll out the form on the
Contact Us page. We hope you enjoy your eect pedal and use it to make great music!
“To be used only
where the climate
is not tropical”
“The Lightning Flash with arrowhead symbol
within an equilateral triangle, is intended
to alert the user to the presence of uninsulated
“dangerous voltage” within the product enclosure
that may be of suf�icient magnitude to constitute
a risk of shock to persons.”
“The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.”
“To be used only
with altitude
not exceeding 2000 m”
03
2. CONTENTS
INTRODUCTION 3
FUNCTION OVERVIEW 4
CONNECTIONS 4
MARKBASS PEDAL CONTROLLER SOFTWARE 5
TECHNICAL SPECS 5
BLOCK DIAGRAM 5
3. INTRODUCTION
Congratulations on your purchase of the Markbass stereo SUPER SYNTH.
This pedal turns your bass into a synthesizer—with seriously cool sounds and no tracking delay! It also doubles as a digital octaver, with both octave up and octave down layers. The
easy-to-read display always identies what eect is being applied. The parameters of the pedal’s presets can be modied using the Markbass Pedal Controller software, which is
available for download from the pedal’s product page at www.markbass.it. Simply install the software, connect the pedal to your computer using a USB cable, modify the presets as
desired, and then load them back onto the pedal.
Like all our pedals, this unit features true bypass: that means that when the eect is ‘o’, your signal goes directly from the input jack to the output jack without any degradation of
audio quality.
This manual will help you get the most out of your pedal. If you have any questions after reading it, please feel free to contact our online customer service department at
[email protected].
Thank you again, and enjoy your Markbass stereo SUPER SYNTH!
04
4. FUNCTION OVERVIEW
GAIN (1) - Controls the level of input into the pedal, from -10 ÷ +16dB.
CUT FREQ / OCT -1 (2) - In Synth mode, this knob controls the cutoff frequency, from 70Hz to 14000Hz. In Octaver mode, it con-
trols the volume level of the lower octave (one octave below your dry signal).
TONE / OCT +1 (3) - In Synth mode, this knob allows you to select from seven (1-7) factory presets of Detune, Amp and Pan
settings of the oscillators, and one user preset (8). In Octaver mode, it controls the volume level of the upper octave (one octave
above your dry signal).
LEVEL/DRY (4) - In Synth mode, this switch controls the output level from the pedal. In Octaver mode, it’s a volume knob for your
dry signal.
PRESETS (5) – This switch lets you scroll through the 12 presets in the pedal
True Bypass Switch (6)∗ - Toggles between “on” and bypass mode. The LED illuminates when the synth/octaver effect is active.
“Software Instructions” to nd out how to create and store presets on your computer.
DC IN (11) - External power supply connection: 12VDC (550 mA minimum) PSU.
∗True Bypass
When the pedal’s controls are ‘off’, your signal goes directly from the input jack to the output jack without any degradation of
SYNTH/OCTAVER Switch (7) - This switch toggles between Synth and Octaver modes.
DISPLAY (8) -The digital display is easy to read and always identies what effect is active.
5. CONNECTIONS
1/4” INPUT JACK (9) - Connect your instrument to the input jack. Make sure your amp is off and ensure that the volume is turned down before making connections.
1/4” OUTPUT JACK LEFT/MONO (10) - Output for a mono effect signal or, when both outputs are connected, the left channel of
the stereo effect signal.
1/4” OUTPUT JACK RIGHT (13) - Output of the right channel when running stereo.
CONTROL (12) - The USB connection allows you to modify the parameters on your computer using the supplied Markbass
software, and then store your favorite settings back on the pedal to have them at your disposal whenever you need them! See
audio quality.
LIMITED WARRANTY
Markbass oers an international limited warranty on Markbass products purchased from any authorized Markbass dealer, eective from the day of purchase. The terms of this warranty
vary from country to country; please contact the Markbass distributor in your country for details.
Please register this product online at www.markbass.it to establish the date of purchase. However, please note that you are required to retain a copy of your receipt as proof of purchase
in order to receive warranty service.
This warranty does not apply to any damage to the product caused by misuse, mishandling, accident, abuse, alteration, modication or unauthorized repairs. Product appearance and
normal wear and tear (worn paint, scratches, etc.) are not covered by this warranty. Markbass reserves the right to be the sole arbiter regarding the misuse or abuse of this product.
Markbass assumes no liability for any incidental or consequential damages, which may result from the failure of this product. Any warranties implied in fact or by law are limited to the
duration of this express limited warranty. Your legal rights related to the warranty will vary depending on the country of purchase.
WARRANTY CARD
This product is guaranteed by the warranty provided in the country of purchase, under the following conditions:
A - The MARKBASS warranty is only applicable if this document been properly completed (here or online) and if the original invoice/bill of sale, mentioning model, serial number and
purchase date, is presented together with this document.
B - The obligations of MARKBASS are limited to the repair of defects. Warranty repair eligibility will be decided at the sole discretion of MARKBASS or its representatives. Freight, freight
insurance costs, and any other costs related to the repair of this product are not covered by this warranty.
C - All warranty repairs must be made by MARKBASS or an authorized MARKBASS (PARSEK) service center.
D - This warranty does not apply in the following instances:
• if the damage was caused by accident, negligence or modications; use of non MARKBASS spare parts; or improper use, installation or packing;
• if the serial number on the equipment is illegible;
• if the damage was caused by lightning, water, re, incorrect main voltage, insucient ventilation or any other cause beyond the control of MARKBASS.
E - This warranty is not applicable to any speaker that has been subjected to power in excess of that for which it has been designed.
F - MARKBASS reserves the right to redesign or improve/modify its product at any time without any obligation to modify previously manufactured products.
Parsek srl. - Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52/A Tel. +39 085 446 37 55 - Fax +39 085 440 77 64 www.momark.it - www.markbass.it [email protected]
WARRANTY CARD
We’d like to thank you for choosing a Markbass product.
If any problem occurs, please don’t hesitate to contact our support team at [email protected].
You can ll out this form and send a copy to Markbass (Parsek srl, Via Po 52, 66020 San Giovanni Teatino, CHIETI ITALY) or, even better, you can now register your warranty online in a
matter of minutes, using our online registration form at www.markbass.it. Simply point, click and type in your information...and you’re done!
Registering your warranty identies you and your product, in case you are ever in need of warranty service. Please note that in order to qualify for warranty service, you must retain a
copy of the sales receipts or bill of delivery as proof of purchase.
The information that you provide here will not be shared with any third parties and will be used for Markbass business purposes only.
PRODUCT INFORMATION
Model : _________________________ Serial Number: _________________________
Date of Purchase : _________________________(mm/dd/yyyy)
DEALER INFORMATION
Dealer: _________________________ Dealer City: _________________________ Dealer Country _________________________
PERSONAL INFORMATION
Purchased by
First Name _________________________ Last Name _________________________ Your Email Address _________________________
Address _________________________ City _________________________ State/Prov _________________________
Zip _________________________ Country _________________________
Do you want to join our mailing list? □ YES □ NO
MORE INFO (* not mandatory)
*Age _________________________ *Sex _________________________ *Occupation _________________________
WHERE DO YOU PLAY YOUR INSTRUMENT?
□ Stage / Performing Musician □ School / Student □ Classroom / Educator □ Home □ Studio Recording
WHAT LEVEL OF PLAYER ARE YOU?
□ Beginner □ Amateur □ Semi-Professional □ Professional
PRODUCT PURCHASED VIA:
□ Internet □ Retail Store
WHAT MOST INFLUENCED YOUR BUYING DECISION?
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
05
6. MARKBASS PEDAL CONTROLLER SOFTWARE
To customize your Super Synth pedal, simply download the software from this pedal’s product page at
www.markbass.it, install it on your Mac or PC computer, and connect your pedal to the computer using
a standard USB cable.
Launch the software, click on “CONNECT” button and wait for connection. The software gives you more
control over the presets than the pedal itself does… so you can completely customize your sounds in
real time and save up to twelve presets to suit your needs perfectly. Future updates of the Markbass
Pedal Controller software may be downloaded for free from www.markbass.it as they become available.
Please stay tuned!
Although the Super Synth pedal performs some pretty complex technical feats, Markbass has designed
the user interface to be as simple and easy-to-use as possible!
MODE: This switch toggles between Synth and Octaver modes (same as the switch on the pedal).
SYNTH
CUTOFF: controls the cuto frequency of the synth lter
LEVEL: controls the synth output level
TONE: this control allows you to select from seven factory presets with dierent presets of
Detune, Amp and Pan of the three oscillators. You can modify the Dynamic
settings of these presets, but not the Oscillaror parameters. The Super Synth
parameter controls are located on two pages: DYNAMICS and OSCILLATORS.
The one User preset allows you to modify the parameters on both the Dynamics
and Oscillators pages.
DYNAMICS
NOTE DYNAMICS SECTION
NOTE ON LEVEL: controls how hard you have to play in order to trigger the synth sound
(note on). The further you turn this up, the harder you have to play
to trigger the synth sound
NOTE OFF LEVEL: controls the level at which the synth sound is untriggered (note o). As
the synth note is decaying, at a certain point the synth sound
disappears and you just have dry sound. Here you can adjust the
volume level at which this transition happens
AMP DYNAMIC: controls how much the dynamics of the synth sound follow the dynamics
of your playing
FILTER DYNAMIC: controls how much the envelope of dry sound increases the cuto lter
FILTER AND MIX SECTION
CUTOFF: the synth’s lter cuts out the range of frequencies above the specic frequency set
here. It responds dynamically to the envelope of your bass sound,
depending on how Filter Dynamic and Envelope are set
RESONANCE: controls the resonance of the synth lter
LEVEL: controls the synth output level
MIX: controls the mix between the original sound and the synth
ENVELOPE CONTROL SECTION
AT TACK: controls the envelope attack time
RELEASE: controls the envelope release time
PORTAMENTO: transition time between two dierent notes
ENVELOPE: controls how much the envelope generator increases the cuto lter
OSCILLATORS
Oscillators 1 / Oscillators 2 / Oscillators 3
DETUNE: detunes the note, measured in semi-tones
DETUNE FINE: detunes the note, measured in cents
AMP: amplitude of the oscillator
PAN: oscillator stereo balance L/R
OCTAVER
OCTAVE +1: volume level one octave above the dry signal
OCTAVE 1: volume level one octave below the dry signal
OCTAVE 2: volume level two octaves below the dry signal
DRY: volume of the dry signal
7. TECHNICAL SPECS
INPUT: 1x ¼” mono jack
INPUT IMPEDANCE: 200 Kohm
OUTPUTS: 2x ¼” mono jack (mono L , stereo L+R)
PRESETS: 12 (user modiable)
GAIN: -10 ÷ +16dB
CUT FREQ SYNTH MODE 70 ÷ 14000 Hz
TONE PRESETS: seven factory presets (1-7) / one user presets
(8)
POWER REQUIREMENTS  DC INPUT: +12 Vdc 550 mA minimum
DIMENSIONS: 170 x 145 x 60 mm
6.7” x 5.7” x 2.4”
WEIGHT: 730 g / 1.61 lbs
8. BLOCK DIAGRAM
Via Po, 52 - 66020 San Giovanni Teatino (Ch) - Italy - Tel. +39 085 446 3755 - Fax +39 085 440 7764
www.markbass.it - [email protected]
Product specifications are subject to change without notice
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

MarkBass Super Synth Le manuel du propriétaire

MarkBass
Marque
MarkBass
Modèle
Super Synth
Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents