Superior Fireplaces DRI2000 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRI2000

Catégorie: Cheminées

Taper: Mode d'emploi

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating

plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements locaux

le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque signalétique. Cet

appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

INSTALLATEUR: Laissez cette notice avec l'appareil.

CONSOMMATEUR: Conservez cette notice pour consul-

tation ultérieure.

— Do not store or use gasoline or other ﬂammable vapors

and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result

in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED'INDENDIE OU D'EXPLOSION

Le non-respect Des avertissements de sécurité pour-

rait d'entraîner des blessures graves, la mort ou des

dommages matériels.

— Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où vous

trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du fournis-

seur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

— L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé ou

par le fournisseur de gaz.

A French manual is available upon request. Order

P/N 900787-05.

INSTALLATION AND OPERATION

Ce manuel d’installation est disponible en francais, s

implement en faire la demande. Numéro de la pièce

900787-05.

MODELS

P/N 900787-04 REV. G 06/2020

Direct-Vent

DRI2000TEN Series

DRI2027TEN

DRI2032TEN

Report # F17-137

CUS

P900787-04

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier* designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and must be installed for the protection of children and

other at-risk individuals. *Included with required facade.

DANGER

PELIGRO

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

L'écran pare-étincelles* fourni avec ce foyer réduit le risque de brûlure en cas

de contact accidentel avec la vitre chaude et doit être installé pour la protection

Des enfants et Des personnes à risques. *incluse avec le façade - Requis.

Una barrera* diseñada para reducir el riesgo de quemaduras desde la mirilla (vidrio)

caliente es proveida con este aparato y deberá instalarse para la protección de los

niños y otros individuos en riesgo. *Incluida con la fachada requerida.

SAFETY AND YOUR FIREPLACE INSERT

Vea el volante adjunto para la representación de color adecuado

Voir ci-joint tract pour une bonne représentation de la couleur

See attached color ﬂyer for proper color representation

 Aﬁn d'éviter les brûlures

graves ou les blessures,

ne pas retirer l'écran

de protection de la

face avant (accessoire

obligatoire) qui

empêche tout contact direct avec la

vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer deviennent

EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du foyer atteint

des températures EXTRÊMEMENT

ÉLEVÉES et peut causer de graves

blessures en cas de contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact avec

la vitre.

• Tenez tous les vêtements, les meubles,

l'essence et tout autre liquide

inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées (voir Pages 6-7).

 Lisez la section Informations

importantes relatives à la sécurité,

Page 5.

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de este

peligro de quemadura:

• ¡Las superﬁcies de la chimenea se

ponen MUY CALIENTES!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los niños

en cualquier cuarto donde haya una

chimenea funcionando para impedir el

contacto con el vidrio.

• Mantenga la ropa, mobiliario, gasolina

y otros líquidos inﬂamables alejados

de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente

calientes.

 Asegúrese de colocar las Etiquetas de

advertencia de seguridad de operación

en el lugar donde enciende la chimenea,

para que todos recuerden los peligros

asociados con las altas temperaturas

(ver la páginas 6-7).

 Lea la Información importante de

seguridad en la página 5.

Seguridad y su

chimenea

La sécurité et votre

poêle encastrable

[FRENCH][ENGLISH]

[SPANISH]

Safety and Your

Fireplace Insert

 To prevent severe burns

and injuries, do Not

remove the barrier on

the facade (required

accessory) which

prevents direct contact

with the glass.

 Follow the safety instructions below

and be sure everyone in your household

understands this burn hazard:

• The surfaces on your ﬁreplace get

EXTREMELY HOT!

• The glass on the front of the

ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an operating

ﬁreplace. Closely supervise children

in any room where a ﬁreplace is

operating to prevent contact with glass.

• Keep clothing, furniture, gasoline, and

other ﬂammable liquids away from the

ﬁreplace.

• Even after the gas is turned off,

ﬁreplace surfaces remain extremely

hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated with

high temperatures (see Pages 6-7).

 Read Important Safety Information on

Page 5.

All parts of your IHP

ﬁreplace insert get

EXTREMELY HOT!

Toutes les parties de votre

poêle encastrable IHP

deviennent EXTRÊMEMENT

CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

CONGRATULATIONS!

When you purchased your new gas ﬁreplace insert, you joined

the ranks of thousands of individuals whose answer to their home

heating needs reﬂects their concern for aesthetics, efﬁciency and

our environment. We extend our continued support to help you

achieve the maximum beneﬁt and enjoyment available from your

new gas ﬁreplace insert.

Thank you for selecting an Innovative Hearth Products, LLC (IHP)

gas ﬁreplace insert as the answer to your home heating needs.

TABLE OF CONTENTS

Safety and Your Fireplace Insert ....................................... 2-3

Using this Manual .......................................................... 4

Important Safety Information ............................................. 5

Homeowner - Attaching Safety In Operation Warnings ............... 6

Installer - Attaching Safety In Operation Warnings ................... 7

Appliance Installation, Service, and Maintenance Notices .......... 8

Appliance Operation Notices .............................................. 8

Warranty Information ...................................................... 8

Important Safety And Warning Information ............................. 9

Oriﬁce Size / Altitude Adjustment .......................................10

Smoke Detectors ...........................................................10

Fireplace Requirements ..................................................10

Codes and Approvals ......................................................11

Requirements For The Commonwealth of Massachusetts ...........11

Pre-Installation.........................................................12-14

Features ...........................................................12

Packaging List .................................................... 12

Ratings.............................................................12

Insert and Fireplace Dimensions ..............................13

Clearances to Combustibles ....................................14

Insert Leveling ....................................................14

Installation ..............................................................15-21

Venting Installation .............................................. 15

USING THIS MANUAL

Please read and carefully follow all of the instructions found in this

manual. Please pay special attention to the safety instructions provided

in this manual.

PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE

Preparation For Flex Liner Installation .......................15

Vertical Venting ..................................................16

Zero Clearance Fireplace Installation ........................16

Flue Restrictor ....................................................16

Firebox Liner (standard) ........................................17

Full Front Facade Installation (required accessory) ........ 17

Log Set Installation .............................................. 17

Gas Line Installation ............................................20

Gas Pressure Requirements ....................................20

LP and Natural Gas Supplies ...................................20

Air Shutter Adjustment ..........................................21

Battery Backup - Battery Installation ..........................21

Operating Instructions ................................................22-24

Pre-Lighting Checklist ...........................................22

Operating Instructions .......................................... 22

Intermittent/Standing Pilot Mode ..............................22

Blower Operation .................................................22

Flame Color and Behavior ......................................23

Paint Curing .......................................................23

Quiet Operation ...................................................23

Wiring Diagram ..................................................24

Maintenance and Servicing .......................................... 25-28

Maintenance Checklist ..........................................25

Door Removal ....................................................26

Glass Maintenance ..............................................27

Fuel Conversion ..................................................27

Blower Removal ..................................................27

Replacing A Damaged Barrier .................................28

Troubleshooting ............................................................ 29

Replacement Parts ....................................................30-33

Accessories .............................................................34-35

Insert Labels ............................................................36-38

Warranty ....................................................................39

Product Reference Information .......................................... 40

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Important Safety Informa-

tion

1. WARNING: Do not operate appliance

with the glass front removed, cracked

or broken.

2. Do not use this appliance if any part

has been under water. Immediately

call a qualiﬁed service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been under

water.

3. Due to high temperatures, the appli-

ance should be located out of trafﬁc

and away from furniture and draperies.

4. Children and adults should be alerted

to the hazards of high surface tem-

perature and should stay away to avoid

burns or clothing ignition.

5. Clothing or other ﬂammable material

should not be placed on or near the

appliance.

6. Young children should be carefully

supervised when they are in the same

room as the appliance. Toddlers,

young children, and others may be sus-

ceptible to accidental contact burns.

A physical barrier is recommended

if there are at-risk individuals in the

house. To restrict access to a ﬁreplace

or stove, install an adjustable safety

gate to keep toddlers, young children,

and other at-risk individuals out of the

room and away from hot surfaces.

7. Any safety screen, guard or barrier

removed for servicing an appliance

must be replaced prior to operating

the appliance.

8. Installation and repair should be done

by a qualiﬁed service person. The

appliance should be inspected before

use and at least annually by a profes-

sional service person. More frequent

cleaning may be required due to

excessive lint from carpeting, bedding

material, et cetera. It is imperative

that control compartments, burners,

and circulating air passageways of the

appliance be kept clean. See mainte-

nance instructions on Pages 25-28.

L’information de sûreté

importante

1. AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en

place, est craqué ou brisé.

2. Ne pas se servir de cet appareil s’il a été

plongé dans l’eau, même partiellement.

Faire inspecter l'appareil par un technicien

qualiﬁé et remplacer toute partie du systéme

de contrôle et toute commande qui ont été

plongées dans l'eau.

3. En raison des températures élevées,

l’appareil devrait être installé dans un

endroit où il y a peu de circulation et loin

du mobilier et des tentures.

4. Les enfants et les adultes devraient être

informés des dangers que posent les tem-

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

5. On ne devrait pas placer de vêtements

ni d’autres matières inflammables sur

l’appareil ni à proximité.

6. Les jeunes enfants devraient être surveillés

étroitement lorsqu’ils se trouvent dans la

même pièce que l’appareil. Les tout petits,

les jeunes enfants ou les adultes peuvent

subir des brûlures s’ils viennent en contact

avec la surface chaude. Il est recommandé

d’installer une barrière physique si des

personnes à risques habitent la maison.

Pour empêcher l’accès à un foyer ou à un

poêle, installez une barrière de sécurité

; cette mesure empêchera les tout petits,

les jeunes enfants et toute autre personne

à risque d’avoir accès à la pièce et aux

surfaces chaudes.

7. Tout écran ou protecteur retiré pour per-

mettre l’entretien de l’appareil doit être

remis en place avant de mettre l’appareil

en marche.

8. L’installation et la réparation devrait être

conﬁées à un technicien qualiﬁé. L’appareil

devrait faire l’objet d’une inspection par un

technicien professionnel avant d’être utilisé

et au moins une fois l’an par la suite. Des

nettoyages plus fréquents peuvent être

nécessaires si les tapis, la literie, et cetera

produisent une quantité importante de pous-

sière. Il est essentiel que les compartiments

abritant les commandes, les brûleurs et les

conduits de circulation d’air de l’appareil

soient tenus propres. Voyez les instructions

d’entretien à la Pages 25-28.

Información importante de

seguridad

1. ADVERTENCIA: No opere el artefacto con el

frente de vidrio quitado, agrietado o roto.

2. No use este artefacto si alguna de sus partes

ha estado bajo agua. Llame de inmediato

a un técnico de servicio caliﬁcado para

que inspeccione el artefacto y reemplace

cualquier parte del sistema de control y

cualquier control de gas que haya estado

bajo agua.

3. Debido a las altas temperaturas, el artefacto

debe situarse fuera de las áreas de tráﬁco y

lejos del mobiliario y cortinas.

4. Se debe alertar a los niños y adultos sobre

los peligros de las altas temperaturas en la

superﬁcie y que se mantengan alejados para

evitar quemaduras o ignición de la ropa.

5. No debe colocarse ropa u otros materiales

inﬂamables sobre y cerca del artefacto.

6. Se debe supervisar de cerca a los niños

cuando estén en el mismo cuarto que el

artefacto. Los niños pequeños, los jóvenes

y otras personas pueden ser susceptibles

a quemaduras por contacto accidental. Se

recomienda instalar una barrera física si hay

personas en riesgo en la casa. Para restringir

el acceso a una chimenea o estufa, instale

una puerta de seguridad ajustable para

mantener a los niños pequeños, jóvenes y

otras personas en riesgo fuera del cuarto y

lejos de las superﬁcies calientes.

7. Cualquier malla o resguardo de seguridad

quitado para dar servicio a un artefacto, debe

reinstalarse antes de operar el artefacto.

8. Una persona de servicio competente debe

realizar la instalación y reparación. Una

persona de servicio profesional debe

inspeccionar el artefacto antes de usar al

menos una vez por año. Se puede requerir

limpieza más frecuente debido a la pelusa

excesiva del alfombrado, del material de

cobijas, etc. Es imprescindible mantener

limpios los compartimientos de control, los

quemadores y los pasajes de circulación del

aire del artefacto. Ver las instrucciones de

mantenimiento en la páginas 25-28.

IMPORTANT SAFETY INFORMATION

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure A

Figure B

Illustrations are for example only.

Your accessories may be different.

Les illustrations sont par exemple

uniquement. Vos accessoires peuvent

être différents.

Las ilustraciones son sólo ejemplos.

Tu accesorios pueden ser diferentes.

OFF

ATTACHING SAFETY IN OPERATION WARN-

INGS

Your ﬁreplace has been furnished with safety instruc-

tion labels that are to be afﬁxed to the operation and

control points of the ﬁreplace. A safety instruction label

should be afﬁxed to the receiver wall switch plate where

the ﬁreplace is turned on and off (See Figure A) and

the remote control handheld transmitter (Figure B).

The warnings should already have been put in place

when the ﬁreplace initial set-up was completed. If they

are not afﬁxed at these spots, locate the multi-lingual

adhesive labels provided with these instructions and

proceed as follows:

1. Locate the wall receiver that controls the ﬁreplace

(verify the switch operates the ﬁreplace by turn-

ing it on and off). Clean the wall receiver plate

thoroughly to remove any dust and oils. Afﬁx the

label to the surface of the plate of the wall receiver

that controls the ﬁreplace (Figure A). Choose

the language primarily spoken in the home.

2. Locate the remote control transmitter and clean

it thoroughly to remove any dust and oils. Afﬁx

the label to the surface of handheld transmitter

(Figure B). Choose the language primarily spoken

in the home.

3. If you are unable to locate the labels, please

call Innovative Hearth Products or your nearest

Innovative Hearth Products dealer to receive

additional safety instruction labels free of charge.

Cat. No. H8024 Replacement Label Kit

Innovative Hearth Products

SuperiorFireplaces.us.com

NOTE: English is red text on clear label. French

and Spanish are white text on black label.

APPOSITION DES MISES EN GARDE RELATIVES À

LA SÉCURITÉ D’UTILISATION

Votre foyer a été livré avec des étiquettes de sécurité qui

doivent être collées à côté des dispositifs de contrôle du

foyer. Une étiquette de sécurité devrait être collée sur

la plaque du récepteur mural contrôlant l’allumage du

foyer (voir Figure A) et sur le boîtier de la télécommande

(Figure B). Les mises en garde auraient dû être collées

au moment de l’installation initiale du foyer. Si ce n’est

pas le cas, prenez les étiquettes adhésives multilingues

fournies avec ces instructions et procédez comme suit:

1. Repérez le récepteur mural qui contrôle le foyer

(vériﬁez que l’interrupteur contrôle le fonction-

nement du foyer en le faisant basculer de Marche

à Arrêt, et vice-versa). Nettoyez soigneusement la

plaque du récepteur mural pour éliminer la poussière

et les traces de graisse ou d’huile. Collez l’étiquette

sur la surface de la plaque du récepteur mural qui

contrôle le foyer (Figure A). Choisissez la langue

qui est principalement parlée dans la résidence du

propriétaire.

2. Repérez la télécommande et nettoyez-la soigneuse-

ment pour éliminer la poussière et les traces de

graisse ou d’huile. Collez l’étiquette sur le boîtier de

la télécommande (Figure B). Choisissez la langue

qui est principalement parlée dans la résidence du

propriétaire.

3. Si vous ne trouvez pas les étiquettes, veuillez appeler

Innovative Hearth Products ou votre distribu teur

Innovative Hearth Products local pour recevoir

gratuitement des étiquettes supplémentaires.

Étiquettes de remplacement, n° cat. H8024

Innovative Hearth Products

SuperiorFireplaces.us.com

Remarque : Le texte anglais est rouge sur un support

transparent. Le texte français et espagnol est blanc

sur un support noir.

COLOCACIÓN DE ADVERTENCIAS DE SEGURIDAD

EN OPERACIÓN

Su chimenea incluye etiquetas de instrucciones de

seguridad que deben colocarse en los puntos de

operación y control de la chimenea. Se debe colocar

una etiqueta de instrucciones de seguridad en la placa

del interruptor de pared del receptor desde el cual

se enciende y se apaga la chimenea (ver la Figura

A) y en el transmisor de control remoto (Figura B).

Las advertencias ya deben haberse colocado cuando

se completó la instalación inicial de la chimenea. Si

no están colocadas en estos lugares, encuentre las

etiquetas adhesivas multilingües proporcionadas con

estas instrucciones y prosiga de la siguiente manera:

1. Identiﬁque el receptor de pared que controla la

chimenea (veriﬁque que el interruptor opera la

chimenea encendiéndola y apagándola). Limpie bien

la placa del receptor de pared para quitar el polvo y

aceite. Pegue la etiqueta en la superﬁcie de la placa

del receptor de pared que controla la chimenea

(Figura A). Seleccione el idioma que más se habla

en la casa.

2. Identiﬁque el transmisor de control remoto y límpielo

bien para quitar el polvo y aceite. Pegue la etiqueta

en la superﬁcie del transmisor (Figura B). Seleccione

el idioma que más se habla en la casa.

3. Si no puede encontrar las etiquetas, sírvase llamar

a Innovative Hearth Products o al distribuidor de

Innovative Hearth Products más cercano para recibir

etiquetas de instrucciones de seguridad adicionales

gratuitas.

Juego de etiquetas de repuesto - Nº de cat. H8024

Innovative Hearth Products

SuperiorFireplaces.us.com

Nota: La etiqueta en inglés es transparente con texto

rojo. Las etiquetas en francés y español son negras

con texto blanco.

HOMEOWNER’S INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS

SAFETY LABEL DIAGRAMS DIAGRAMAS DE ETIQUETAS DE

SEGURIDAD

DIAGRAMMES DES ÉTIQUETTES

DE SÉCURITÉ

OFF

PILOT

Continuous

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ATTACHING SAFETY IN OPERATION

WARNINGS

It is required that the set of safety instruction labels

that have been furnished with the ﬁreplace be afﬁxed

to the operation and control points of the ﬁreplace. A

safety instruction label must be afﬁxed to the receiver

wall switch plate where the ﬁreplace is turned on and

off (See Figure A) and on the remote control handheld

transmitter (See Figure B). To properly complete the

installation of this ﬁreplace, locate the multi-lingual

adhesive labels provided with the Care and Operation

Instructions and proceed as follows:

1. Locate the wall receiver that controls the ﬁreplace

(verify the switch operates the ﬁreplace by turn-

ing it on and off). Clean the wall receiver plate

thoroughly to remove any dust and oils. Afﬁx the

label to the surface of the plate of the wall receiver

that controls the ﬁreplace (Figure A). Choose

the language primarily spoken in the home. If

unknown, afﬁx the English language label.

2. Locate the remote control transmitter and clean

it thoroughly to remove any dust and oils. Afﬁx

the label to the surface of handheld transmitter

(Figure B). Choose the language primarily

spoken in the home. If unknown, afﬁx the English

language label.

3. If you are unable to locate the labels, please

call Innovative Hearth Products or your nearest

Innovative Hearth Products dealer to receive

additional safety instruction labels free of charge.

Cat. No. H8024 Replacement Label Kit

Innovative Hearth Products

SuperiorFireplaces.us.com

NOTE: English is red text on clear label. French

and Spanish are white text on black label.

APPOSITION DES MISES EN GARDE RELATIVES

À LA SÉCURITÉ D’UTILISATION

Il est impératif que le jeu d’étiquettes de sécurité qui

ont été fournies avec le foyer soient collées à côté

des dispositifs de contrôle du foyer. Une étiquette de

sécurité doit être collée sur la plaque du récepteur mural

contrôlant l’allumage du foyer (voir Figure A) et sur le

boîtier de la télécommande (Figure B). Pour achever

l’installation correcte de ce foyer, procédez comme suit

avec les étiquettes adhésives en langues étrangères

fournies avec les instructions d’utilisation et d’entretien :

1. Repérez le récepteur mural qui contrôle le foyer

(vériﬁez que l’interrupteur contrôle le fonction -

-nement du foyer en le faisant basculer de Marche

à Arrêt, et vice-versa). Nettoyez soigneusement

la plaque du récepteur mural pour éliminer la

poussière et les traces de graisse ou d’huile. Collez

l’étiquette sur la surface de la plaque du récepteur

mural qui contrôle le foyer (Figure A). Choisissez

la langue qui est principalement parlée dans la

résidence du propriétaire. En cas de doute, collez

l’étiquette en anglais.

2. Repérez la télécommande et nettoyez-la soigneuse-

ment pour éliminer la poussière et les traces

de graisse ou d’huile. Collez l’étiquette sur le boîtier

de la télécommande (Figure B). Choisissez la

langue qui est principalement parlée dans la

résidence du propriétaire. En cas de doute, collez

l’étiquette en anglais.

3. Si vous ne trouvez pas les étiquettes, veuillez

appeler Innovative Hearth Products ou votre distribu-

teur Innovative Hearth Products local pour recevoir

gratuitement des étiquettes supplémentaires.

Étiquettes de remplacement, n° cat. H8024

Innovative Hearth Products

SuperiorFireplaces.us.com

Remarque : Le texte anglais est rouge sur un support

transparent. Le texte français et espagnol est blanc

sur un support noir.

COLOCACIÓN DE ADVERTENCIAS DE SEGURIDAD

EN OPERACIÓN

Se requiere que el juego de etiquetas de instrucciones

de seguridad que se incluyeron con la chimenea se

coloque en los puntos de operación y control de la

misma. Se debe colocar una etiqueta de instrucciones

de seguridad en la placa del interruptor de pared

del receptor desde el cual se enciende y se apaga

la chimenea (ver la Figura A) y en el transmisor de

control remoto (ver la Figura B). Para completar

correctamente la instalación de esta chimenea,

encuentre las etiquetas adhesivas multilingües

incluidas con las instrucciones de cuidado y operación

y haga lo siguiente:

1. Identiﬁque el receptor de pared que controla la

chimenea (veriﬁque que el interruptor opera la

chimenea encendiéndola y apagándola). Limpie

bien la placa del receptor de pared para quitar el

polvo y aceite. Pegue la etiqueta en la superﬁcie

de la placa del receptor de pared que controla la

chimenea (Figura A). Seleccione el idioma que

más se habla en la casa. Si no sabe cuál es, use la

etiqueta en inglés.

2. Identiﬁque el transmisor de control remoto y límpielo

bien para quitar el polvo y aceite. Pegue la etiqueta

en la superﬁcie del transmisor (Figura B). Seleccione

el idioma que más se habla en la casa. Si no sabe

cuál es, use la etiqueta en inglés.

3. Si no puede encontrar las etiquetas, sírvase llamar

a Innovative Hearth Products o al distribuidor de

Innovative Hearth Products más cercano para

recibir etiquetas de instrucciones de seguridad

adicionales gratuitas.

Juego de etiquetas de repuesto - Nº de cat. H8024

Innovative Hearth Products

SuperiorFireplaces.us.com

Nota: La etiqueta en inglés es transparente con texto

rojo. Las etiquetas en francés y español son negras

con texto blanco.

INSTALLER INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS

It is the installer’s responsibility to ensure these warnings are properly afﬁxed during installation. These warning labels are a critical

step in informing consumers of safe operation of this appliance.

SAFETY LABEL

DIAGRAMS

DIAGRAMAS DE ETIQUETAS

DE SEGURIDAD

DIAGRAMMES DES ÉTIQUETTES

DE SÉCURITÉ

Figure A

Figure B

Illustrations are for example only.

Your accessories may be different.

Les illustrations sont par exemple

uniquement. Vos accessoires peuvent

être différents.

Las ilustraciones son sólo ejemplos.

Tu accesorios pueden ser diferentes.

OFF

PILOT

Continuous

Appliance Installation, Service, and

Maintenance Notices

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage.

Refer to the owner’s information manual provided with this

appliance. For assistance or additional information consult a

qualiﬁed installer, service agency or the gas supplier.

AVERTISSEMENT : Une installation, un réglage, une

modiﬁcation, une réparation ou un entretien mal effectué

peut causer des dommages matériels ou des blessures.

Voir la notice de l’utilisateur qui accompgne l’appareil.

Pour de l’aide ou des renseignements supplémentaires,

consultez un installateur, un technicien agréé ou le

fournisseur de gaz.

Only trim kit(s) supplied by the manufacturer shall be used

in the installation of this appliance.

Seules les trousses de garniture fournies par le fabricant

doivent être utilisées pour l’installation de cet appareil.

These appliances must not be connected to a chimney or ﬂue

serving a separate solid fuel burning appliance.

Any change to this appliance and/or its operating controls is

dangerous. Improper installation or use of this appliance can

cause serious injury or death from ﬁre, burns, explosion or

carbon monoxide poisoning.

CARBON MONOXIDE POISONING: Early signs of carbon

monoxide poisoning are similar to the ﬂu with headaches,

dizziness and/or nausea. If you have these signs, obtain fresh

air immediately. Turn off the gas supply to the appliance and

have it serviced by a qualiﬁed professional, as it may not be

operating correctly. Some people are more affected by carbon

monoxide than others, including pregnant women, people with

heart or lung disease or anemia, those under the inﬂuence of

alcohol, and those at high altitudes.

Turn off gas and electrical power to the appliance and allow

it to cool before cleaning or servicing the appliance.

If the barrier becomes damaged, the barrier shall be

replaced with the manufacturer’s barrier for this appliance.

Si l'écran est endommagé, il doit être remplacé par

celui fournit par le fabricant de cet appareil.

Reinstall any barrier removed before operating the

appliance. The barrier is designed to reduce the risk of

burns from hot glass. Do not operate the appliance without

the barrier installed.

Appliance Operation Notices

These ﬁreplace inserts are vented gas appliances. Do not

burn wood or other material in these appliances.

These appliances are designed to operate on natural gas or

propane gas only. The use of other fuels or combinations of

fuels will degrade the performance of this system and may

be dangerous.

Provide adequate clearances around air openings and

adequate accessibility clearance for service and proper op-

eration. Never obstruct the front openings of the appliance.

These appliances are designed as supplemental heaters.

Therefore, it is advisable to have an alternate primary heat

source when installed in a dwelling.

Warranty Information

Your gas appliance is covered by a

limited 20-year warranty

You will ﬁnd a copy of the warranty accompanying this manual.

Please read the warranty to be familiar with its coverage.

Retain this manual. File it with your other documents for future

reference.

Failure to comply with the installation and operating

instructions provided will result in an improperly installed

and operating appliance, voiding its warranty.

Do not attempt to alter or modify the construction of the

appliance or its components. Any modiﬁcation or alteration

may void the warranty, certiﬁcation, and listings of this unit.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

IMPORTANT SAFETY AND WARNING

INFORMATION

WARNING

This product can expose you to chemicals includ-

ing Carbon Black, which is known to the State of

California to cause cancer, and Carbon Monoxide,

which is known to the State of California to cause

birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov

 INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE

HOME OWNER!

FOR YOUR SAFETY do not install or operate this appliance without

ﬁrst reading and understanding this manual. Any installation or

operation of the appliance deviating from that which is stated

in this manual WILL void the warranty and may be hazardous.

 IHP, its employees, or any of its representatives assume no

responsibility for any damages caused by an inoperable, inad-

equate, or unsafe condition as a result of any improper operation,

service or installation procedures, whether direct or indirect.

 DO NOT ATTEMPT TO SERVICE THE APPLIANCE YOURSELF.

 Do not make any make-shift compromises during installation.

Any modiﬁcation or alteration may result in damage to the ap-

pliance or dwelling and will void the warranty, certiﬁcation and

listings of this unit.

Failure to use manufacturer provided parts, variations in tech-

niques and construction materials or practices other than those

described in this manual may create a ﬁre hazard and void the

limited warranty.

This gas appliance must be equipped for the proper fuel type

and altitude at which it will be operated. Any operation outside

the parameters outlined in this manual may result in a hazard-

ous condition and will void the warranty. Please carefully read

the sections pertaining to these subjects and/or be sure your

appliance is properly equipped.

 Never use solid fuels such as wood, paper, cardboard, coal, or

any ﬂammable liquids, etc., in this appliance.

CAUTION: Hot while in operation. Do not touch. Severe Burns

may result. Keep children, clothing furniture, gasoline and other

liquids having ﬂammable vapors away.

ATTENTION: L’appareil est chaud lorsqu’il fonctionne. Ne

pas toucher l’appareil. Risque de brûlures graves. Sur-

veiller les enfants. Garder les vêtements, les meubles,

l’essence ou autres liquides produisant des vapeur inﬂam-

mables loin de l’appareil.

Clearances are in accordance with local installation codes and

the requirements of the gas supplier.

Les dégagements sont conformes aux codes d'installation

locaux et aux exigences du foumisseur de gaz.

This appliance is only for use with the type of gas indicated on

rating plate. This appliance is not convertible for use with other

gases, unless a certiﬁed kit is used.

Cet appareil doit être utilisé uniquement avec les types de

gaz indiqués sur la plaque signalétique. Ne pas l'utiliser

avec d'autres gaz sauf si un kit de conversion certiﬁé est

installé.

WARNING

Failure to comply with these installation instructions

will result in an improperly installed and operating

appliance, voiding its warranty.

WARNING

Improper installation or use of this appliance can

cause serious injury or death from ﬁre, burns,

explosion or carbon monoxide poisoning.

For altitudes above 2,000 feet (In Canada 4,500 FT/1370 M), the oriﬁce

should be de-rated by 4% for every 1,000 feet to maintain the proper ratio

of gas to air. Improper oriﬁce sizing may result in damage and unsafe

conditions. Changing the oriﬁce should only be done by a qualiﬁed service

technician. Contact your IHP dealer for proper oriﬁce sizes.

In Canada - CAN/CGA-2.17-M91 (R2009) (high altitude):

THE CONVERSION SHALL BE CARRIED OUT BY A MANUFACTURER’S

AUTHORIZED REPRESENTATIVE, IN ACCORDANCE WITH THE REQUIRE-

MENTS OF THE MANUFACTURER, PROVINCIAL OR TERRITORIAL

AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN/CGA-B149.1 OR CAN/CGA-B149.2

INSTALLATION CODES.

ORIFICE SIZE/ALTITUDE ADJUSTMENT

THE FIREPLACE INSERT

Since there are always several potential sources of ﬁre in any home, we

recommend installing smoke detectors. If possible, install the smoke

detector in a hallway adjacent to the room (to reduce the possibility of

occasional false activation from the heat produced by the appliance). If

your local code requires a smoke detector be installed within the same

room, you must follow the requirements of your local code. Check with

your local building department for requirements in your area.

SMOKE DETECTORS

• Must conform with all local, state and national installation codes. In

the absence of local codes, the installation must conform with National

Fuel Gas Code ANSI Z223.1 - latest edition, also known as NFPA 54

(In Canada, the current CAN/CGA B149.1 installation code). Refer to

the National Fuel Gas Code and local zoning and code authorities for

details on installation requirements.

• Manufactured home installations (USA only) must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR,

Part 3280, or, when such a standard is not applicable, the Standard for

Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard

for Gas Equipped Recreational Vehicles and Mobile Housing, CSA

Z240.4.

• Must be vented directly to the outside in accordance with the latest

edition of the National Fuel Gas Code and must never be attached to

a chimney serving a separate solid fuel burning appliance.

• Has been certiﬁed for use with either natural gas or propane.

• Is NOT for use with solid fuels.

• Is approved for sitting rooms and/or bedrooms.

• This appliance is suitable for installation into masonry or factory built

ﬁreplaces.

Fireplace Requirements

These heaters are designed to be installed into an existing masonry

ﬁreplace (built to UBC 37 or ULC S628 standards) or factory built solid

fuel, wood burning ﬁreplace (listed to UL 127 or ULC S610) only. All

exhaust gases must be vented outside the structure. Combustion air

is drawn from outside the structure. When installing in a factory built

ﬁreplace, the ﬁreplace grate must be removed and the damper must be

removed or secured open.

IMPORTANT: When installing these appliances into a factory

built ﬁreplace or heat-form, the air ﬂow within and around the

ﬁreplace shall not be altered by the installation of the insert

(i.e. DO NOT BLOCK louvers or cooling air inlet or outlet ports,

circulating air chambers in a steel ﬁreplace liner or metal heat

circulator).

CAUTION

• Trim panels or Full Front Facades must not seal

ventilation openings in the existing ﬁreplace

that the appliance is installed in.

• The ﬁreplace in which this gas insert is to be

installed must be thoroughly cleaned if it has

been used to burn wood or synthetic logs. Have

the chimney and all inside surfaces of the ﬁre-

place brushed and vacuumed so that no soot,

embers, or loose combustion deposits can be

drawn into the heat circulation blower and blown

into the living area.

• If any portion of the chimney system shows signs

of structural or mechanical weaknesses, such

as: cracks, leaky joints, corroded or warped

surfaces, the faulty portion must be repaired

or replaced prior to installing this appliance.

• The factory built ﬁrebox must accept the insert

without modiﬁcation other than removing bolted

or screwed together pieces such as bafﬂes /

smoke shelf / deﬂectors, ash lips, glass door,

screen or door tracks, log grates, refractory or

masonry lining and damper assemblies. Any

ﬁreplace component, which is removed, must be

retained so they can be reinstalled to restore the

ﬁreplace to its original operating condition. The

removal of any part must not alter the integrity

of the outer shell of the pre-engineered ﬁreplace

cabinet in any way. Any parts removed must be

replaceable. If any components are removed

from (or altered) from the existing ﬁreplace, a

Warning Label (see Figure 1) must be afﬁxed

inside the ﬁreplace ﬁrebox, so that it shall be

visible upon removal of the ﬁreplace insert.

NOTE: Afﬁx the label inside the existing ﬁreplace

ﬁrebox using two (2) self-drilling sheet metal

screws (provided).

• The ﬁrebox metal ﬂoor may be removed in certain

cases*.

* The removal of the ﬁrebox ﬂoor is not covered

under the appliance safety standard (ANSI Z21.88

/ CSA 2.33) used in the safety certiﬁcation of this

appliance. Check with local building codes to ensure

this form of installation is permitted. When installed

on the outer sheet metal structure of the ﬁreplace,

minimum of 1-1/2" of cement board or 1/2" cement

board with 1/2" air space must be placed under the

full length and width of the appliance in order to

prevent the risk of ﬁre hazard.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

These appliances are approved for installation in the US state of Mas-

sachusetts if the following additional requirements are met:

• Install this appliance in accordance with Massachusetts Rules and

Regulations 248 C.M.R. Sections 4.00 through 8.00.

• Installation and repair must be done by a plumber or gas ﬁtter licensed

in the Commonwealth of Massachusetts.

• The ﬂexible gas line connector used shall not exceed 36 inches (92

centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations installed

less than seven (7) feet above the ﬁnished grade must comply with the

following additional requirements:

• A hard wired carbon monoxide detector with an alarm and battery

back-up must be installed on the ﬂoor level where the gas ﬁreplace

is installed. The carbon monoxide detector must comply with NFPA

720, be ANSI/UL 2034 listed and be ISA certiﬁed.

• A metal or plastic identiﬁcation plate must be permanently mounted to

the exterior of the building at a minimum height of eight (8) feet above

grade and be directly in line with the horizontal termination. The sign

must read, in print size no less than one-half (1/2) inch in size, GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.

Figure 1 - Fireplace Warning Label

Certiﬁcation

Gas appliances must be tested and certiﬁed by a nationally recognized

testing and certiﬁcation laboratory to ANSI (American National Standard

Institute) gas appliance safety standards.

This appliance has been tested and certiﬁed to ANSI Z21.88/CSA 2.33

Standard for Vented Gas Fireplace Heater and CAN/CGA 2.17-M91 and

UL 307B Gas Burning Heating Appliances for Manufactured (Mobile)

Homes in both USA and Canada.

This appliance has met all necessary ANSI Standards and is fully certi-

ﬁed for installation in any community. If there are any questions or if you

need further substantiation contact your IHP dealer. If you have further

questions, please contact IHP.

Check all local building and safety codes before installation. The installation

instructions and appropriate code requirements must be followed exactly

and without compromise. In the absence of local codes the following

standards and codes must be followed.

The Installation must conform with local codes or, in the absence of

local codes, to the National Fuel Gas Code, ANSI Z223.1/NFPA 54- latest

edition, or the Natural Gas and Propane Installation Code, CAN/CGA

B149.1- latest edition.

The appliance, when installed, must be electrically grounded and wired

in accordance with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70 - latest edition, or the Canadian

Electrical Code, CSA C22.1 - latest edition.

CODES AND APPROVALS

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

P/N 900803-00 Rev. 0

WARNING / AVERTISSEMENT

This ﬁreplace has been converted for use with a

gas ﬁreplace insert only and cannot be used for

burning wood or solid fuels unless all original

parts have been replaced, and the ﬁreplace re-

approved by the Authority Having Jurisdiction.

Ce foyer a été converti pour utilisation avec un

foyer au gaz encastrable et ne peut être utiliser

pour brûler du bois ou d’autres combustibles

solides à moins que toutes les pièces d’origine

aient été remplacées et que le foyer ait été

approuvé de nouveau par l’autorité compétente.

RATINGS

DRI2027 DRI2032

NATURAL GAS LP GAS NATURAL GAS LP GAS

Max/Min Input BTUh 0-2,000 Feet (0-610 M)u 25,000 / 14,000 22,500 / 13,300 28,000 / 16,000 25,000 / 14,000

Manifold Pressure (IN. WC) 3.5 / 1.2 10.0 / 3.2 3.5 / 1.2 10.0 / 3.2

Min. Inlet Pressure (IN. WC) 5.0 10.5 5.0 10.5

AFUE Efﬁciency 78% 75% 70% 67%

P4 Efﬁciency

v 73% 73% 57% 61%

Oriﬁce (DMS) 0-2,000 Feet (0-610 M)u #41 (.096") #54 (.055") #38 (.101") #53 (.0595")

uUnit factory equipped for 0-2000 FT/0-610 M, In Canada 0-4500 FT/0-1370 M

vComplies with CSA P.4.1-2015 “Testing Method for Measuring Annual Fireplace Efﬁciency.

Electrical Rating: 120 VAC, 60 HZ, Less Than 2 Amps

Based on CSA P. 4.1-2015

Features

Installation Options

.25 Manufactured (Mobile) Home

.25 Natural Gas Or Propane (LP)

.25 Bedrooms

Electrical

The standard blower motor requires 120 Volts AC for operation. The

ﬁreplace is not dependent on the blower to operate.

WARNING: Electrical Grounding Instructions - This appliance is equipped

with a three-prong (grounding) plug for your protection against shock

hazard and should be plugged directly into a al electrical 120 Volt

power is required to operate the blower system of this appliance and

recommended to operate the burner system. This appliance is equipped

with a battery backup system in case of a power outage (see Battery

Backup on Page 23 for more information).

Fuel

THIS APPLIANCE IS EQUIPPED FOR NATURAL GAS.

This appliance is equipped with an oriﬁce sized for operation with

natural gas.

For conversion to LP/propane gas, see instructions provided with

the appliance.

Oriﬁces and instructions necessary for LP/propane conversion are

provided in the gas conversion kit (see Pages 35-36 for ordering

information).

This appliance comes from the factory equipped to burn natural gas at a

speciﬁed elevation. Only IHP conversion kits can be used to convert from

NG to LP or LP to NG. Contact your IHP dealer for details.

PRE-INSTALLATION

Packaging List

Insert Body Packaging List

1 Insert Body

1 Power Cord

1 Log Set

1 Bag of Embers

1 Literature Package (installation and operation manual, warning labels,

and hardware kit*).

*Hardware kit contents:

4 Threaded 1/4-20 x 2.5" appliance leveling bolts

2 #8 x 3/8" Phillips screws

4 #8 Washers (Full Front Facade panel installation)

4 8-32 Nuts (Full Front Facade panel installation)

Full Front Facade Kits - One Required

3 Sided (See ACCESSORIES page for size options)

4 Sided - Trimmable (See ACCESSORIES page for size options)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Minimum Fireplace Opening

Dim. Description DRI2027 DRI2032

A * Front Opening Width 27” (686mm) 32” (813mm)

B Height 18" (457mm) 19-1/2” (495mm)

C Rear Width 17" (432mm) 22” (559mm)

D Fireplace Depth 15” (381mm) 16” (406mm)

Top View

Left Side View

Right Side View

Front View

Figure 2 - Insert Dimensions

O.D. = 2-15/16" (75mm)

Model A B C D E F G H

DRI2027

17-7/8"

(454mm)

14-7/8"

(378mm)

10-7/8"

(276mm)

26-5/8"

(676mm)

16-3/4"

(425mm)

8-3/4"

(222mm)

14-3/8"

(365mm)

20-3/4”

(527mm)

DRI2032

19-3/8”

(492mm)

15-7/8”

(403mm)

11-7/8”

(302mm)

31-5/8”

(803mm)

21”

(533mm)

9-3/4”

(248mm)

15-3/8”

(391mm)

25-3/4”

(654mm)

(77mm)

* The front opening width (A) must be maintained to a 3" depth into the

ﬁreplace ﬁrebox. See ﬁgure shown here.

3” (76mm) *

Figure 1 - Minimum Fireplace Cavity

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

CLEARANCES TO COMBUSTIBLES

Minimum Clearances to Combustibles

Minimum clearances include any projections such as shelves, window

sills, mantels, spacers/standoffs or surfaces to combustible construction

etc. above the appliance. Paint or lacquer used to ﬁnish the mantel

must be heat resistant in order to avoid discoloration.

Facing and Mantel Clearances (see Figure 4)

The letters in Figure 4 (A through E) show minimum clearances required

from the appliance to combustibles and the minimum projection of the

hearth extension.

Figure 4 - DRI2027 and DRI2032 Clearances

MINIMUM CLEARANCES

MINIMUM CLEARANCES TO COMBUSTIBLES DRI2027/DRI2032

A = Mantel .................................................. 32" (813mm)

B = Side Wall .................................................. 4" (102mm)

C = Mantel Depth ........................................... 10" (254mm)

HEARTH PROTECTION

D = Vertical Distance from base of appliance 0"

to Hearth Extension ................................. (0mm) (102mm)

E = Minimum Horizontal Distance 10" 0”

from Front of Appliance........................... (254mm) (0mm)

Insert Leveling

At each front and rear corner of the insert is an adjustable leg provided

to level the insert should the hearth of the ﬁreplace be uneven. To adjust

the legs, use a 1/4" wrench.

Non-Combustible

Mantel

NOTE: Hearth protection to be min. 1/2” (13mm) thick

non-combustible or equivalent, with a k factor of .84.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Venting Installation

Your IHP appliance must be vented to the outside in accordance with the

current edition of the National Fuel Gas Code ANSI-Z223.1 (In Canada,

the current CAN/CGA B149.1 installation code).

This appliance requires a 3” diameter listed ﬂex liner. The vent should

terminate with a listed direct-vent termination cap. The chimney should be

sealed around the cap to prevent air and rain from entering the chimney.

Adhere to the vent manufacturer's instructions for installation and vent

termination. These appliances are approved for use with the following

vent kits.

INSTALLATION

Intake

Liner Connector Plate

Exhaust

Vertical Cap

Termination

Connector

Exhaust

Intake

The existing ﬁreplace chimneys

may take various contours which

the ﬂexible liners will accommo-

date. However, keep the ﬂexible

liner VERTICAL and avoid bend-

ing. When at maximum vertical

height, standing pilot should be

used for correct operation.

Liner Requirements:

Use 3" (77 mm) diameter listed gas

vent liner (UL1777 ONLY) for the

EXHAUST

Use 3" (77 mm) diameter listed

liner (UL 181 or UL1777) for the

AIR INTAKE.

Figure 5

Figure 6

Preparation For Flex Liner Installation

The liner connector plate can be removed (as shown in Figure 6) to make

it easier to connect the ﬂex liners to the intake and exhaust collars. Re-

install the liner connector plate when the insert is placed in the ﬁreplace.

NOTE: Ensure gasket on connector plate is not damaged before re-

installing.

Simpson Dura Vent -

Flex Liner 3" X 35' - #3DFA-35

Adaptor w/ Flashing - #46DVA-GK

Termination Cap - #46DVA-VCH

With #460 DVA-VWG

Termination Cap - #460DVA-VC

Co-Linear Kit w/ 3" X 35' Flex Liner

(Intake and Exhaust), Adaptor,

Flashing and Termination Cap -

#46DVA-CL33

Selkirk -

Termination Cap - #4DT-VT

Vent Adaptor - #4DT-CTB

Venting - 3' x 35' #AF35-03

Venting - 3' x 25' # AF25-03

Venting - 3' x 15' # AF15-03

All Models:

Vertical Height Min. = 10 ft. (3.1 M)

Model DRI2032:

Vertical height Max. = 35 ft. (10.7 M)

Model DRI2027:

Vertical height Max. = 25 ft. (7.6 M)

NOTE: Measured from base on

unit to the end of the vent pipe

or liner

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Vertical Venting (see Figure 5, Page 15)

The vent pipes must be connected to the proper collars on the unit and

the exhaust vent pipe must be connected to the termination cap or the unit

will not operate. When done assure all connections are securely fastened.

The ﬁreplace and ﬁreplace chimney must be clean and in good working

order and constructed of non-combustible materials. Inspect chimney

cleanouts for proper ﬁt and seal.

Make sure that both liners will pass through existing damper area.

Remove or lock damper to allow the passage of the ﬂexible liners. If

the damper will not allow the passage of both liners, DO NOT PROCEED

FURTHER. (If ﬁreplace is masonry) Consult a local mason for removal

of the damper without risk of structural damage or leakage (if the ﬁre-

place is factory built) The appliance may NOT be installed into the ﬁreplace.

WARNING

Direct-Vent Fireplace Insert Vent Requirements - Use liner

listed to UL181 (Factory-made Air Ducts And Air Connec-

tors) or UL1777 (Chimney Liners) for the AIR INTAKE. Use

liner listed to UL1777 ONLY for the EXHAUST.

Do not substitute the heat-rated ﬂex liner (UL1777) for

the exhaust with any other type liner or a ﬁre may result

causing property damage, personal injury or loss of life.

Zero Clearance Fireplace Installation

This appliance may be installed in a masonry or factory built/zero clear-

ance (ZC) ﬁreplace. When installing in a ZC ﬁreplace, the ZC grate must

be removed and the ZC damper must be removed or secured open. The

ZC doors, screen, refractory or masonry lining, bafﬂes and smoke shelf

may be removed if necessary to install the gas insert. However, do not cut

or alter the ﬁreplace components. The removal of any parts to facilitate

installation must not alter the integrity of the inner or outer shells of the

ﬁreplace cabinet. Any parts removed must be replaceable if the insert is

taken out of the ﬁreplace or the ﬁreplace clearly marked with a paint stick

that "This ﬁreplace has been altered and is no longer safe to operate."

If the factory-built ﬁreplace has no gas access hole(s) provided, an access

hole of 1.5" (38.1 mm) or less may be drilled through the lower sides or

bottom of the ﬁrebox in a proper workmanship like manner. This access

hole must be plugged with a non-combustible insulation after the gas

supply line has been installed.

Si le foyer préfabriqué ne comporte pas d’oriﬁces d’amenée du gaz,

un oriﬁce d’au plus 38,1 mm (1,5 po) peut être pratiqué, selon les

règles de l’art, dans la partie inférieure des parois ou au fond de

la chambre de combustion. Cet oriﬁce doit être obturé au moyen

d’isolant incombustible une fois la conduite de gaz en place.

The installer must mechanically attach the marking supplied with the gas

ﬁreplace insert to the inside of the ﬁrebox of the ﬁreplace into which the

gas ﬁreplace insert is installed. See Figure 1 on Page 11.

Figure 7

Flue Restrictor

The ﬂue restrictor settings shown in Figure 7 are for typical installations

and are based upon laboratory testing. To achieve proper combustion,

adjustments may be needed to account for variables in the installation,

elevation, and typical operating temperatures.

Allow the appliance to burn for at least 10 minutes before determining

proper ﬂame appearance. If the proper ﬂame appearance cannot be

achieved, the ﬂue restrictor may need to be changed to a different posi-

tion. See the following guidelines to determine if you need to readjust

the ﬂue restrictor.

Flue Restrictor Adjustment

1. Using a phillips screwdriver, remove the two screws holding the ﬂue

restrictor in place.

2. Refer to table in Figure 7 and position the ﬂue restrictor to the recom-

mended setting and reattach with the two screws removed in step 1.

Symptoms - Lack of Combustion Air

If the symptoms listed below are present, you may need to adjust the

ﬂue restrictor to a more open position.

• Flame appears yellow

• Floating Flames (lazy, ill deﬁned, quiet, may roll)

• Sooting

• Pilot becomes yellow and appliance shuts down

Symptoms - Excessive Combustion Air

If the symptoms listed below are present, you may need to adjust the

ﬂue restrictor to a more closed position.

• Low Flame

• Pilot pulls and appliance shuts down

• Pilot ﬂame ghosts

NOTE: Setting 0 is open, and setting 3 is closed.

2 1 0

Model Venting Height Position

Natural Gas (NG)

32" Models

25' or less #1 (factory setting)

25' & up # 2

27" Models

20' or less # 2

20' & up # 2

Propane (LP)

32" Models

10' - 15' # 0

15' - 25' #1 (factory setting)

25' & up # 2

27" Models

10' - 15' # 0

15' - 25' # 0

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Firebox Liner Kit

1. Remove the glass door following the instructions provided in this

manual (Page 27).

2. Place the rear liner panel against the back of the Firebox and resting

on the burner support tray.

3. One at a time, install the side liner panels by sliding them into place

(Figure 8).

4. Steel and Porcelain panels: using the short 'L' brackets, secure the

liner panels by fastening the bracket to the top edge of the Firebox

with a #8 x 3/8" Phillips screw provided with this manual (Figure 8).

Figure 8

Figure 9

A = Openings where hooked brackets on Full Front Facade will hang.

B = Side Mounting Brackets on appliance

Full Front Facade Installation

See the installation instructions packaged with your Full Front Facade.

See Page 33 for ordering information.

1. Position the appliance in the ﬁreplace, but a few inches in front of its

ﬁnal location.

2. Using the screw provided, install the Control Assembly onto the left

side of the Full Front Facade.

3. Hang the hooked brackets on the Full Front Facade into the openings

on the side mounting brackets on the appliance (see Figure 9).

Installing the logs, volcanic stone, and glowing embers

WARNING

• Turn OFF all gas and electricity to the appliance

before installing the volcanic stone, embers,

and logs.

• Do NOT install the logs until the appliance has

been completely installed, the gas line connect-

ed and tested for leaks, and the initial burner

operation has been conﬁrmed.

• Use of an unapproved log set in the appliance will

void the warranty and will result in incomplete

combustion, sooting, and poor ﬂame quality.

• Logs get very hot and remain hot for up to one

hour after the gas supply is turned OFF. Handle

the logs only when cool.

• This appliance is not designed to burn wood.

Any attempt to do so could cause irreparable

damage to appliance and prove hazardous.

• If the logs are not installed according to these

instructions, improper combustion could occur.

This could result in the excessive production of

soot and/or the colorless, odorless, toxic gas

carbon monoxide (CO).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

NOTE: If applicable, install the ﬁrebox liner before placing the stone.

Logs can be installed after the volcanic stone.

Installing the volcanic stone, and glowing embers:

1. If necessary, remove the glass door (Page 27).

2. Spread the decorative volcanic stone in a pleasing pattern on the

ﬁrebox ﬂoor to the front and sides of the burner (Figure 10).

NOTE: Do not place volcanic stone on the burner.

3. Separate and ﬂuff the glowing embers into pieces approximately the

size of a quarter (Figure 11).

4. Position the separated glowing embers over the small holes on the

burner surface (Figure 12). Do NOT cover the large burner slots.

NOTE: Enough glowing ember material is provided for several applica-

tions. For best glowing effect, replace the ember material annually.

Figure 10 - Installing the volcanic stone (DRI2032 Shown)

Figure 11 - Separating the glowing embers

Figure 13 - Log Set

Log Number Description

1 Rear Log

2 Left Front Log

3 Right Front Log

4 Left Cross Log

5 Right Cross Log

NOTE: It is important to ensure proper log placement per the

manual when installing these units. Verify pilot ﬂame is not

obstructed. See Verifying Appliance Operation on Page 26.

Volcanic Stone

Figure 12 - Installing the glowing embers (DRI2032 Shown)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Log Installation Instructions - DRI2027 and DRI2032

The logs have notches/tabs to assist proper positioning. Upper logs rest

on lower logs via notches/tabs. Proper log placement is critical to pre-

vent sooting. Place the logs in the gaps between ﬂame peaks, so they do

not impinge the ﬂames. Follow the log placement instructions precisely.

NOTE: Do not cover the burner ports.

NOTE: Ensure the left front log (1) and right front log (2) are correctly

installed on the burner positioning tabs.

1. If necessary, remove the glass door (Page 26). Locate and bend up

Burner Locating Tabs (Figure 14A or 14B).

2. Locate the log placement tabs (Figure 14A or 14B). Place embers

and other media (see Page 18).

Figure 14A - Locate the log placement tabs, DRI2027

Figure 14B - Locate the log placement tabs, DRI2032

Figure 15 - Place log 1

4. Position the left front log (2) on the left front log tab and the left

burner locating tab (See Figures 14A/B and 16).

Figure 16 - Place log 2

Figure 17 - Place log 3

Position the left cross log (4) on the landings on the left rear log (1) and

the left front log (2) (see Figures 17 and 18).

7. Position the right cross log (5) over the right rear locating tab (see Fig-

ures 14A/B and 18).

3. Align the notches in the bottom of the rear log (1) with the left rear

locating tabs (see Figures 14A/B and 15).

5. Position the right front log (3) on the right front locating tab and right

burner locating tab (See Figures 14A/B and 17).

Figure 18 - Place logs 4 and 5

4 5

Tab for

log #5

Tabs for

log #2

Tabs for

log #1

Tabs for

log #3

Landings for

log #4

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Gas Line Installation

After leveling, position the insert in the ﬁreplace - holding it about six

inches out from its ﬁnal location.

CAUTION: Speciﬁc hearth requirements apply (see Clearances

to Combustibles).

This appliance must be connected to the gas line in accordance with local

codes and/or the National Fuel Gas Code, ANSI Z223.1 (In Canada, the

current CAN/CGA B149.1 installation code). This appliance comes with

an 5" nipple, provided in the literature package. After connecting the gas

line, all joints in the line and connections at the valve should be checked

for leaks before ﬁnal positioning of the unit. Conduct a gas leakage test

of the appliance piping and control system downstream of the shutoff

valve in the supply line to the appliance.

Gas Pressure Requirements

A MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS

APPLIANCES IS IMPROPER GAS PRESSURE!

The most important item to check during the initial installation

and the ﬁrst thing to check when operating problems occur is

gas pressure! This appliance will not function properly unless

the required gas pressure is supplied. See the tables on this

page for gas pressure requirements.

Gas Pressure Test Points

Manifold Gas Pressure Test Points - The outlet manifold test gauge

connection is provided on the valve stem (see Figure 19A).

Inlet Gas Pressure Test - The inlet line gas pressure test point is located

in the control compartment (see Figure 19B).

The control valves have a 3/8” (10 mm) NPT thread inlet and outlet side

of the valve.

If the pressure is not sufﬁcient, make sure the gas supply line is large

enough, the supply regulator is properly adjusted and the total gas load

for the residence does not exceed the amount supplied.

Propane tanks are at pressures that will cause damage to valve com-

ponents. Verify that the tanks have step down regulators to reduce the

pressure to safe levels.

Check the taps for gas leaks with a gas leak test solution (retighten if

necessary).

LP and Natural Gas Supplies

This appliance is equipped from the factory for use with natural gas only

as speciﬁed on the Safety / Listing label attached to the appliance. This

appliance can only be operated using propane gas (LP) if a certiﬁed fuel

conversion kit provided by IHP is installed by a qualiﬁed service technician.

Also check the oriﬁce size on the label which is located in the control

compartment. It must be the correct size for the fuel and altitude.

Do not run propane tank dry. Running the tank dry may cause a

hazardous condition due to pressure drop in empty tank.

Solid fuel is NOT to be used with this appliance.

The appliance must be isolated from the gas supply piping system

by closing its equipment shutoff valve during any pressure testing of

the gas supply piping system at test pressures equal to or less than

1/2 psig (3.5 kPa).

The appliance and its appliance main gas valve must be disconnected

from the gas supply piping system during any pressure testing of that

system at test pressures in excess of 1/2 psig (3.5 kPa).

Figure 19A - MANIFOLD Outlet Gas Pressure Test Point

Inlet Gas Supply Pressure

Fuel Minimum Maximum

Natural Gas 5” WC (1.25 kPa) 10.5” WC (2.61 kPa)

Propane 11.0” WC (2.74 kPa) 13.0” WC (3.23 kPa)

Manifold Gas Supply Pressure

Fuel Pressure - High Pressure - Low

Natural Gas 3.5” WC (0.87 kPa) 1.2” WC (0.30 kPa)

Propane 10.0” WC (2.49 kPa) 3.2” WC (0.80 kPa)

Some parts have been removed for clarity

1/8” Inlet gas pressure ‘test point’ plug

(in control compartment)

Testing Inlet Gas Pressure

(Qualiﬁed Technicians

Only):

1. Turn off gas shutoff

valve and electrical.

2. Remove 1/8” plug

(shown in diagram

below).

3. Install an 1/8” nipple in

place of plug.

4. Connect manometer to

nipple, using an 1/8”

NPT air hose nipple/

ﬁtting.

5. Turn on shutoff valve

and check for proper

inlet gas pressure.

6. Reverse steps 1-5.

Figure 19B -

INLET Line Gas Pressure Test Point

Ecoﬂow

Outlet Pressure

Test Point

La page charge ...

Superior Fireplaces DRI2000 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRI2000

Catégorie: Cheminées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Superior Fireplaces DRI2000 Operating instructions

Superior Fireplaces DRI2000 Mode d'emploi

Superior Fireplaces DRI2000 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents