Sonance Patio Series 4.1 Manuel utilisateur

Marque: Sonance

Modèle: Patio Series 4.1

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Ce manuel convient également à

SR 2-125

TWO-CHANNEL DSP AMPLIFIER

INSTRUCTION MANUAL

TABLE OF CONTENTS

2 Important Safety Instructions

4 Introduction and Box Contents

5 Product Features

5 Product Preparation

6 Installation

6 Technical Speciﬁcations

7 Architectural Speciﬁcation

7 Technical Assistance and Service

9 Warranty

READ THIS DOCUMENT IN ITS

ENTIRETY BEFORE ATTEMPTING

INSTALLATION.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. Only use attachments/accessories speciﬁed by

Sonance.

10. Refer all servicing to qualiﬁed service personnel.

DSP AMPLIFIER

SR 2-125 TWO-CHANNEL AMP

DSP AMPLIFIER

SR 2-125 TWO-CHANNEL AMP

IMPORTANT SAFETY INFORMATION

You should always follow these basic safety precautions

when using your SR 2-125 ampliﬁer to reduce the risk of

ﬁre, electric shock, and injury to persons:

1. Read and retain instructions: Read all the safety

and operating instructions before operating the

ampliﬁer, and retain them for future reference.

2. Heed warnings: Adhere to all warnings and

precautions listed on the ampliﬁer and in the

operating instructions.

3. Follow instructions: Follow all operating

instructions.

4. Water: Never use the ampliﬁer next to water.

5. Carts and stands: The ampliﬁer should be used only

with a cart or stand that is recommended by the

manufacturer. An ampliﬁer and cart combination

should be moved with care.

6. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT

USE THE POLARIZED PLUG WITH AN EXTENSION

CORD, RECEPTACLE, OR OTHER OUTLETS UNLESS

THE BLADES CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

7. Ventilation: Situate the ampliﬁer so that its location

does not interfere with its proper ventilation.

8. Heat: Situate the ampliﬁer away from heat sources

such as radiators, stoves, or other appliances

(including ampliﬁers) that produce heat.

9. Grounding or polarization: Grounding or

polarization are precautions that should be taken so

that these attributes are not defeated.

10. Power-cord protection: Route power supply cords

so that they will not be walked on or pinched by

items placed on or against them.

11. Cleaning: To clean the ampliﬁer, use “canned air”

or wipe the ampliﬁer with a soft cloth. Do not use

solvents as they may damage the ampliﬁer.

12. Non-use periods: Unplug the ampliﬁer’s power

cord from the outlet when the ampliﬁer will be left

unused for a long period of time.

13. Object entry: Care should be taken so that objects

do not fall through the opening of the enclosure.

14. Moisture: Do not expose the ampliﬁer to dripping

or splashing. Do not place objects ﬁlled with liquids,

such as vases, on the ampliﬁer.

15. Damage requiring service: Have the ampliﬁer

serviced by a qualiﬁed service personnel when:

• The power supply cord or the plug has been

damaged.

• Objects have fallen, or liquid has been spilled

into the ampliﬁer.

• The ampliﬁer has been exposed to rain.

• The ampliﬁer does not appear to operate normally

or exhibits a marked change in performance.

• The ampliﬁer has been dropped, or the enclosure

damaged.

16. Servicing: The user should not attempt to service

the ampliﬁer beyond that described in the operating

instructions. All other servicing should be referred to

qualiﬁed service personnel.

17. Lifting: Improper lifting of the 11 lbs. SR 2-125 ampliﬁer can

cause personal injury.

18. Power requirement: Do not connect the SR 2-125

ampliﬁer to the accessory outlet of any other

component. A minimum 15 amp (20 amp preferred)

grounded wall outlet is required.

WARNING: THE POWER (MAINS) PLUG SERVES AS THE

AMPLIFIER’S DISCONNECT DEVICE. THE DISCONNECT

DEVICE SHALL REMAIN READILY OPERABLE DURING

OPERATION. TO ENSURE THAT THE DISCONNECT

DEVICE (POWER PLUG) IS EASILY ACCESSIBLE,

THE USER SHALL NOT PLACE THE AMPLIFIER IN A

CONFINED AREA DURING OPERATION.

19. Storms: To prevent damage to components, unplug

all electronic equipment during thunderstorms.

INSTRUCTIONS IMPORTANTES

CONCERNANT LA SÉCURITÉ

1. Lisez soigneusement ces instructions.

2. Conservez-les en lieu sûr pour toute référence future.

3. Respectez scrupuleusement tous les avertissements de

sécurité.

4. Suivez toutes les instructions indiquées.

5. Ne pas utiliser cet appareil près de l’eau.

6. Nettoyez cet appareil uniquement avec un chion sec.

7. Ne jamais obstruer ses ouïes de ventilation. Installez

cet appareil suivant les instructions recommandées par son

fabricant.

8. Ne jamais installer cet appareil près d’une source

dechaleur, comme les radiateurs, bouches de chaleur,

fours ettout autre appareil (y compris les ampliﬁcateurs de

puissance) générant de la chaleur.

9. Ne jamais démonter la prise polarisée ou la broche

de mise à la terre de la prise secteur. Une prise polarisée

possède deux lames, l’une étant plus large que l’autre

(standard américain). Une prise avec mise à la terre

possède trois broches, dont une centrale déportée par

rapport aux deux autres. Ces diérents brochages ont

été conçus pour votre sécurité. Si la prise de l’appareil ne

rentre pas dans la prise d’alimentation secteur de votre

installation, veuillez consulter un électricien agréé pour le

remplacement de la prise murale (certainement pas aux

normes actuelles).

10. Protégez le câble d’alimentation secteur de telle

manière qu’il ne puisse pas être écrasé ou pincé,

particulièrement au niveau des prises, du passage dans des

goulettes prévues à cet usage, ou à l’endroit où il sort de

l’appareil.

11. N’utilisez que les systèmes de ﬁxation et accessoires

prévus et conseillés par le fabricant.

12. N’utilisez que des tables, supports, pieds, bras

de ﬁxation prévus ou conseillés par le fabricant, ou vendus

avec l’appareil. Si un support mobile est utilisé, toujours

procéder avec une grand précaution lors du déplacement

dece support aﬁn d’éviter que l’appareil ne tombe et puisse

blesser physiquement une personne.

13. Débranchez complètement l’appareil pendant un orage

ou une longue période de non-utilisation.

14. Pour toute intervention sur l’appareil, adressez-vous

exclusivement à du personnel qualiﬁé et agréé. Une

interventions’ avérera nécessaire si l’appareil a été

endommagé, pour quelque raison que ce soit, et par

exemple si le câble d’alimentation secteur ou sa

prise sont endommagés, si du liquide a pénétré à

l’intérieur de l’appareil, ou un objet y est tombé, ou bien

si l’appareil a été exposé à la pluie ou à l’humidité, ou

bien est tombé, ou encore ne fonctionne pas de manière

normale.

15. Ne jamais exposer cet appareil à des risques de

coulures ou d’éclaboussures de liquides ; ne jamais

poser d’objets remplis de liquide – comme des vases,

sur l’appareil.

Le symbole de l’éclair terminé par une pointe

de ﬂèche, dans un triangle équilatéral, est utilisé

pour indiquer à l’utilisateur la présence d’une

tension électrique potentiellement dangereuse, à

l’intérieur de l’appareil, d’un niveau susamment

élevé pour présenter des risques d’électrisation

aux personnes physiques.

Le symbole du point d’exclamation, dans un triangle

équilatéral, est utilisé pour indiquer à l’utilisateur,

dans les manuels accompagnant l’appareil, la

présence d’un point très important, concernant le

fonctionnement ou la maintenance de l’appareil, à

respecter impérativement.

ATTENTION

RISQUED’ÉLECTRISATION

NEPASOUVRIR

ATTENTION

AFINDERÉDUIRELESRISQUESD’ÉLECTRISATION, NE

JAMAISÔTERLECAPOTDEL’APPAREIL.ILN’YAÀL’INTÉRIEUR

AUCUNE PIÈCESUSCEPTIBLED’ÊTREMODIFIÉEPARL’UTILISATEUR.

TOUJOURS FAIREAPPELÀUNTECHNICIENAGRÉÉ.

ATTENTION:POURRÉDUIRETOUTRISQUED’ÉLECTROCUTION,

NEJAMAISEXPOSERCET APPAREILÀLAPLUIEOUL’HUMIDITÉ.

ATTENTION

RISQUED’ÉLECTRISATION

NEPASOUVRIR

ATTENTION

AFINDERÉDUIRELESRISQUESD’ÉLECTRISATION, NE

JAMAISÔTERLECAPOTDEL’APPAREIL.ILN’YAÀL’INTÉRIEUR

AUCUNE PIÈCESUSCEPTIBLED’ÊTREMODIFIÉEPARL’UTILISATEUR.

TOUJOURS FAIREAPPELÀUNTECHNICIENAGRÉÉ.

ATTENTION:POURRÉDUIRETOUTRISQUED’ÉLECTROCUTION,

NEJAMAISEXPOSERCET APPAREILÀLAPLUIEOUL’HUMIDITÉ.

ATTENTION

RISQUED’ÉLECTRISATION

NEPASOUVRIR

ATTENTION

AFINDERÉDUIRELESRISQUESD’ÉLECTRISATION, NE

JAMAISÔTERLECAPOTDEL’APPAREIL.ILN’YAÀL’INTÉRIEUR

AUCUNE PIÈCESUSCEPTIBLED’ÊTREMODIFIÉEPARL’UTILISATEUR.

TOUJOURS FAIREAPPELÀUNTECHNICIENAGRÉÉ.

ATTENTION:POURRÉDUIRETOUTRISQUED’ÉLECTROCUTION,

NEJAMAISEXPOSERCET APPAREILÀLAPLUIEOUL’HUMIDITÉ.

WARNING: Any changes or modiﬁcations to this unit

not expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

INTRODUCTION

Thank you for purchasing the SONANCE SR 2-125

ampliﬁer. When properly installed, this ampliﬁer will

give you many years of entertainment pleasure. To get

the most out of your new ampliﬁer please read this

manual thoroughly before you begin installation.

To achieve the best performance SONANCE

recommends that this ampliﬁer be installed by a

SONANCE Authorized Dealer/Installer.

BOX CONTENTS

(1) SR 2-125 Ampliﬁer

(1) Installation Manual

(1) IEC Power Cord

(2) Long Rack Ears

(4) Rubber Feet

(1) DSP Preset Matrix

PLACEMENT

Place the ampliﬁer on a level surface, in an upright

position, out of direct sunlight and away from

windows through which rain may enter.

Situate the ampliﬁer away from heat sources such as

hot air ducts or radiators. Be sure that the ampliﬁer

is adequately ventilated by convection or suitable

cabinet fans.

• Never place any object on or against the ampliﬁer.

• Never operate the ampliﬁer on a carpeted surface as

this will compromise ventilation.

• When the ampliﬁer is installed in any cabinet,

the front or back must be open during operation.

Alternately, install fans in the cabinet to assure

continuous ventilation.

UNPACKING

Save the carton and polystyrene inserts for future safe

transport in case the ampliﬁer is moved or requires

shipping for repair.

Before proceeding with installation locate the serial

number on the rear panel of the unit and note it here for

future reference:

S/N:_____________________________________________

FIGURE 1: SR 2-125 TWO-CHANNEL AMPLIFIER

FIGURE 3: SR 2-125 TWO-CHANNEL AMPLIFIER REAR PANEL

FIGURE 2: SR 2-125 TWO-CHANNEL AMPLIFIER FRONT PANEL

SR 2-125 FRONT PANEL

1. Illuminated Power Button

2. Power, Active & Protection Indicator LED

3. Recessed Volume Level Control

SR 2-125 REAR PANEL

4. L/R Line In/Coax/Toslink

5. Speaker Block Connector

6. Audio Auto On/O Switch

7. EQ Preset Bank

8. EQ Preset Selection

9. AC Fuse Holder

10. Power Cord Connection

PRODUCT FEATURES

Front Panel

Power Switch

The power switch turns the ampliﬁer on and o.

When the power switch is lit solid white, the ampliﬁer

has power, is turned ON and ready to operate.

When the power switch is slightly dimmed the

ampliﬁer is in standby mode.

When the power switch is blinking white, the ampliﬁer

power supply is in thermal protection. The channel LEDs

will also light red when the power supply is in thermal

protect mode.

NOTE: Upon initial power up there will be an

approximately 9-12 second boot up cycle. This is

normal.

Input/Output Lights

When each channel is active, the LED will light green as

long as a signal is present.

When the LED blinks red, this is an indication that the

channel is being overdriven.

When the LED lights are solid red this is an indication

the ampliﬁer is in protect mode. While in protect mode

the LED lights will periodically light green to retest the

output to determine if the short has been removed.

Protect mode could be caused by a short in the wire,

overheating of the ampliﬁer or possibly an internal

problem with the ampliﬁer.

NOTE: WHEN ANY OF THE LEDS ARE LIT RED TURN

THE AMPLIFIER OFF IMMEDIATELY. DETERMINE THE

CAUSE OF THE PROBLEM BEFORE TURNING THE

AMPLIFIER ON.

Volume Level Control

Each channel on the ampliﬁer has front panel recessed

volume controls that will adjust the output and turn

on volume. The ampliﬁer must be powered on to make

these adjustments.

Rear Panel

Inputs

The SR 2-125 ampliﬁer has analog, coax and toslink LINE

INPUTS

and loop OUTPUTS.

The analog loop outputs are non buered. The

maximum number of ampliﬁers that can be looped

together will depend on the output capability of your

source component. The digital outputs are buered

and can support multiple ampliﬁers. Only one output

can be used at a time.

Speaker Connections

The removable block connectors used on the SR 2-125

ampliﬁers will accept up to 12 gauge wire.

Follow the connection layout on the rear panel of the

ampliﬁer. Make sure no bare wires come in contact with

the ampliﬁer chassis.

AC Fuse Holder

To replace the fuse, unplug the power cord from the

Power Cord Connector and use a screwdriver to remove

the fuse holder.

SR 2-125 - 5 amp AC (T5-AL)

CAUTION: FOR CONTINUED PROTECTION AGAINST

FIRE, REPLACE THE FUSE WITH ONLY THE SAME TYPE

AND RATING.

Power Cord

The SR 2-125 ampliﬁers feature removable IEC power

connectors. Plug the female end of the power cord into

the Power Cord Connector on the ampliﬁer rear panel

and plug the male end into a grounded wall socket.

DO NOT plug the ampliﬁer’s power cord into a

convenience outlet on any other audio or video

component. If you need to use an extension cord, use

only a heavy duty (14-GAUGE OR LARGER) extension

cord to avoid starving the ampliﬁer of the current

necessary for full operation.

FIGURE 4: SR 2-125 AMPLIFIER FRONT PANEL VIEW FIGURE 5: SR 2-125 AMPLIFIER REAR PANEL VIEW

POWERING THE AMPLIFIER

The SR 2-125 features a removable

IEC power connector (Figure 6).

A 14-gauge EIA standard 120-

volt grounded power cable is

included with the amplifier.

Each time the ampliﬁer’s power

cord is initially plugged in and the

POWER switch is turned ON, all

channel outputs are disconnected

for approximately 9-12 seconds

and all PROTECTION LEDs will

illuminate brieﬂy while the amp

boots up.

IMPORTANT: DO NOT PLUG THE POWER CORD INTO

THE WALL OUTLET UNTIL ALL SYSTEM CONNECTIONS

HAVE BEEN MADE AND VERIFIED.

Plug the female end of the power cable into the Power

Connector on the ampliﬁer’s rear panel and plug the

male end directly into a grounded 15 amp or 20 amp wall

outlet.

IMPORTANT: DO NOT PLUG THE AMPLIFIER’S POWER

CORD INTO A CONVENIENCE OUTLET ON ANY OTHER

AUDIO OR VIDEO COMPONENT.

If the electrical service is subject to frequent sags, spikes,

or brownouts, a power conditioner designed for use with

high ﬁdelity equipment should be employed to protect

the ampliﬁer.

CAUTION: FOR CONTINUED PROTECTION AGAINST

FIRE, REPLACE THE FUSE WITH ONLY THE SAME TYPE

AND RATING.

Source Connections/Selection SR

2-125

There are two options when connecting audio inputs to the

SR 2-125 ampliﬁer (see Figure 8):

Primary Line Inputs 1-L, 1-R - Use these inputs for analog

audio source.

Primary Line Coax Inputs L&R - Use these inputs for

coax audio source.

Primary Line Toslink Inputs L&R - Use these inputs for

toslink audio source.

Ampliﬁers Power Requirements: 15 AMP Breaker 20 AMP Breaker

Model Input Voltage Output Power (sinewave) Draw Watts Qty of Ampliﬁers Qty of Ampliﬁers

SR 2-125 100-120V AC Full Power All Channels @ 8 ohms 311.5 4 6

Full Power All Channels @ 4 ohms 326 4 5

1/8 Power All Channels @ 8 ohms 61.5 23 31

1/8 Power All Channels @ 4 ohms 63 22 30

@ Idle 26.5

@ Standby 0.3

13 AMP Breaker 20 AMP Breaker

Model Input Voltage Output Power (sinewave) Draw Watts Qty of Ampliﬁers Qty of Ampliﬁers

SR 2-125 220-240V AC Full Power All Channels @ 8 ohms 300 4 6

Full Power All Channels @ 4 ohms 314.5 4 6

1/8 Power All Channels @ 8 ohms 58.5 24 32

1/8 Power All Channels @ 4 ohms 60 24 32

@ Idle 24

@ Standby 0.48

FIGURE 8: SR 2-125 LEFT, RIGHT LINE INPUTS

FIGURE 7: SR 2-125 TWO-CHANNEL AMPLIFIER POWER REQUIREMENTS

1-L 1-R

LEVEL LEVEL

RIDGE

OFF ON

AUTION

RISK OF ELECTRIC SHOCK

O NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE P

AS OUVRIR

S/N

T5AL / 250VAC

2-100

AC 100-120V ~ 60Hz

CAUTION

EPLACE FUSE ONLY WITH

AME TYPE AND RATING

ATTENTION

EMPLACER UNIQUEMENT AVEC LE

MEME TYP

E ET CALIBRE DU FUSIBLE

VOLTAGE TRIGGER

IN OUT

AUTO ON

OFF

1 - LEFT

1 - R

IGHT

BRIDGE

CLASS 2 WIRING

VOLTAGE

AUDIO

3-30 VOLTS

AC or DC

8 Ω MIN

AC 220-240V ~ 50Hz

52 watts

FIGURE 6: IEC POWER

CORD CONNECTION

Speaker Connections

FIGURE 11: VOLUME

LEVEL CONTROL

FIGURE 9:

SPEAKER CONNECTORS

Volume Level Control

Volume can be controlled from the

individual recessed volume level

control screws, located on the front

panel (see Figure 11). These volume

controls balance the desired sound

levels per channel.

The volume level controls are set to

maximum, fully clockwise, by default.

For the best sound you should

use premium speaker wire

that complies with fire rating

codes. Be sure to check

local codes governing wire

that may be installed within

walls or ceilings. SONANCE

ampliﬁers are stable with any

reputable brand of speaker

wire or cable. The SR 2-125

ampliﬁers use speaker

block connectors that can

accommodate up to 12 gauge

wire (see Figure 9).

NOTE: ALWAYS CHECK LOCAL BUILDING CODES BEFORE

INSTALLING WIRE IN WALLS OR CEILINGS.

IMPORTANT: USE CAUTION WHEN SETTING VOLUME

LEVELS EITHER ON THE AMPLIFIER OR AN AUDIO SOURCE

AS NOT TO OVERDRIVE AND POSSIBLY DAMAGE SPEAKERS.

VERIFY ALL SOURCES AS OUTPUT VOLTAGE VARIES FROM

DEVICE TO DEVICE.

Source Connections SR 2-125

On the left side of the rear panel are the audio inputs for

the left and right channels. In addition to the left and right

inputs there are also loop outputs for each channel.

The analog loop outputs are non buered. The maximum

number of ampliﬁers that can be looped together

will depend on the output capability of your source

component. The digital outputs are buered and can

support multiple ampliﬁers. The source connected to the

LEFT and RIGHT LINE IN Inputs pass through the

LEFT and RIGHT LINE Outputs (see Figure 10). This also

applies to the Coax and Toslink inputs.

FIGURE 10: SR 2-125 LEFT, RIGHT LINE INPUTS/OUTPUTS

Protection Circuitry and LEDs

The SR 2-125 ampliﬁers have a multi-stage protection

system to prevent damage to your ampliﬁer and speakers.

SR 2-125 Ampliﬁer Channel Protection

If a channel encounters a short-circuit or an extremely low

impedance this will cause the aected channel outputs to

automatically mute. The output of the aected channel

will remain muted until the fault has been corrected. Only

the aected channels output will mute, all other channels

will continue to operate normally.

SR 2-125 Ampliﬁer Channel Protection Indication

On the front panel of the SR 2-125 ampliﬁers are dual color

LEDs that illuminate to indicate the current operating

status of each ampliﬁer channel.

When the LED blinks red this is an indication that the

channel is being overdriven.

When the LED lights are solid red this is an indication the

ampliﬁer is in protect mode. While in protect mode the

LED lights will periodically light green to retest the output

to determine if the short has been removed. Protect mode

could be caused by a short in the wire, overheating of

the ampliﬁer or possibly an internal problem with the

ampliﬁer.

IMPORTANT: ALLOWING THE AMPLIFIER TO OPERATE

WITH ONE OR MORE CHANNELS IN PROTECT MODE

FOR AN EXTENDED PERIOD OF TIME CAN DAMAGE THE

AMPLIFIER.

SR 2-125 Ampliﬁer Power Supply Protection

The ampliﬁer also has protection for the power supply.

If the power supply heat sink temperature exceeds the

design maximum the protection circuit will activate

disconnecting all channel outputs. This is indicated by a

blinking light on the front panel power switch.

IMPORTANT: ANY TIME THE PROTECTION CIRCUITS ARE

TRIGGERED, UNPLUG THE AMPLIFIER’S POWER CORD

FROM THE WALL OUTLET BEFORE TROUBLESHOOTING.

Rack Ear Installation SR 2-125

The SR 2-125 ampliﬁer ships with two long rack ears for

when the ampliﬁer is to be used alone in a 1U space.

Unscrew the four Phillips head screws (M4 x 0.7 pitch

x 10mm long) found on each side of the left and right

forward section of ampliﬁer. Use these screws to connect

the included rack ears to the ampliﬁer (see Figure 12).

FIGURE 12: RACK EAR INSTALLATION SR 2-125

SIDE VIEW RIGHT

FRONT VIEW

Ampliﬁer Stacking

The SR 2-125 ampliﬁer is capable of being directly

stacked with the feet removed (see Figure 14) for use in

low to moderate output applications. For high-output

applications, it is recommended to leave at least 1U space

between ampliﬁers for increased ventilation.

It is not recommended to stack more than three ampliﬁers

high without spacing.

Shelf Mounting

If shelf mounting, attach the four included feet by

screwing them into the threaded openings, no tool is

required.

To place two SR 2-125 ampliﬁers in a single rack unit order:

Rack Mount Bracket for SR 2-125 SKU# 93098

(see Figure 13).

FIGURE 14: STACKED CONFIGURATION (3) SR 2-125

FIGURE 13: RACK MOUNT BRACKET FOR (2) SR 2-125

FRONT VIEW

Audio - Auto On

Select the Audio Auto On mode you would like to use,

either ON or OFF.

Audio Auto On - ON

When the Audio Auto On switch is in the ON position

the ampliﬁer will power o after 15 minutes without

an audio signal present on any of the channels. When

an audio signal is applied the ampliﬁer will take

approximately 9-12 seconds to reproduce audio after

going through its power up sequence.

NOTE: THE AUDIO AUTO ON - ON MODE USES

THE LEAST AMOUNT OF AC POWER WHEN THE

AMPLIFIER IS NOT OPERATING.

Audio Auto On - OFF

When the Audio Auto On switch is in the OFF position

the ampliﬁer will enter Sleep Mode after 15 minutes

without an audio signal present on any of the channels.

When an audio signal is applied the ampliﬁer will take

approximately 2-3 seconds to reproduce audio.

Apply DSP Preset

The SR 2-125 ampliﬁer includes pre-programmed

DSP presets. These presets are selected utilizing ﬁrst

the EQ Preset Bank dial, followed by the EQ Preset

Selection dial (see included DSP Preset Matrix).

The ﬁrst EQ in any bank will be Flat. To select the

appropriate preset for your environment please see

the included DSP preset Selection Matrix.

QUICK SETUP PAGE

FIGURE 17: SR 2-125 EQ PRESET BANK & EQ PRESET SELECTION

FIGURE 16: SR 2-125

AUDIO AUTO ON - OFF

FIGURE 15: SR 2-125

AUDIO AUTO ON - ON

TECHNICAL ASSISTANCE

AND SERVICE

The Technical Assistance Department at Sonance is

available at (949) 492-7777 to answer any questions

concerning the operation and installation of your

speakers between the hours of 7:00 AM and 5:00 PM

Paciﬁc time, Monday through Friday, except holidays.

In the event your unit should need repair or service, you

may return the unit to your authorized dealer or use the

following guidelines:

PLEASE KEEP ORIGINAL PACKAGING WHEN POSSIBLE.

1. Be prepared to state the model number and / or

serial number, date of purchase, and dealer’s name

and address when calling.

2. Contact Sonance directly at (949) 492-7777

or at www.sonance.com. YOU MUST HAVE PRIOR

AUTHORIZATION TO RETURN YOUR UNIT.

3. If you are returning the product directly to Sonance,

call us to obtain a return authorization number

before shipping.

4. Ship the product via United Parcel Service, Federal

Express, or other package delivery service. Please do

not use the U.S. Postal Service.

5. Include the return authorization number on the

shipping label.

6. Ship to:

Attn: Quality Assurance Department,

RMA#(include RMA number here)

Sonance

11016 Mulberry Ave.

Suite B

Fontana, CA 92337

TECHNICAL SPECIFICATIONS

SR 2-125 Ampliﬁer

Number of Channels 2 (1 stereo pair)

Power Output - 8 ohms 125 Watts RMS per channel (both channels driven)

Power Output - 4 ohms 200 Watts RMS per channel (both channels driven)

Frequency Response 5Hz - 50kHz, bandwidth limited

Total Harmonic Distortion 0.07% (1kHz, 8 ohms) 0.06% (1kHz, 4 ohms)

Signal to Noise Ratio -100dB (20Hz-20kHz)

Input Gain 29dB

Input Sensitivity 100mV for 1 Watt Output @ 8 ohms

1110mV for 125 Watts Output @ 8 ohms

Input Impedance 20k ohms

Loop Output Impedance 600 ohms

Maximum Analog Input Voltage 2.9V VAC RMS

Power Consumption 120V AC

@8 ohms (sinewave, full power) 311.5 Watts (all channels driven)

@4 ohms (sinewave, full power) 326 Watts (all channels driven)

@8 ohms (sinewave, 1/8 power) 61.5 Watts (all channels driven)

@4 ohms (sinewave, 1/8 power) 63 Watts (all channels driven)

@idle 26.5 Watts

@standby 0.3 Watts

Power Consumption 220V AC

@8 ohms (sinewave, full power) 300 Watts (all channels driven)

@4 ohms (sinewave, full power) 314.5 Watts (all channels driven)

@8 ohms (sinewave, 1/8 power) 58.5 Watts (all channels driven)

@4 ohms (sinewave, 1/8 power) 60 Watts (all channels driven)

@idle 24 Watts

@standby 0.48 Watts

Heat Output

@8 ohms (sinewave, full power) 242 BTU (all channels driven)

@4 ohms (sinewave, full power) 314 BTU (all channels driven)

@8 ohms (sinewave, 1/8 power) 118 BTU (all channels driven)

@4 ohms (sinewave, 1/8 power) 124 BTU (all channels driven)

Operating Voltage 100-120V@60Hz, 220-240V@50Hz

AC Fuse 5A (T5AL ~ 250V)

Rack Space Requirement 1U – 1/2 Rack Width

Dimensions w/ Feet (W x H x D) 8 5/8” x 2 1/8” x 16 13/16” (219mm x 54mm x 427mm)

Dimensions w/ Rack Ears w/o Feet (W x H x D) 19” x 1 3/4” x 16 13/16” (482mm x 44mm x 427mm)

Shipping Weight 11 lbs (5.0kg)

CAD Files available for download at www.sonance.com

LIMITED TWO (2) YEAR WARRANTY

Sonance warrants to the ﬁrst end-user purchaser that this Sonance-brand product (“Product”), when purchased from

an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated

above. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product

with a new or remanufactured Product or a reasonable equivalent.

EXCLUSIONS

TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF,

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED

BY SONANCE. ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED.

No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and

exclusive remedy and Sonance’s performance shall constitute full and ﬁnal satisfaction of all obligations, liabilities and

claims with respect to the Product.

IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY,

BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY

OR OTHERWISE.

This warranty statement gives you speciﬁc legal rights, and you may have other rights which vary from state to state.

Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and

limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied

warranties is limited to period of Sonance’s express warranty. Your Product Model and Description: DSP 2-125 Ampliﬁer.

Warranty Period for this Product: Two (2) years from the date on the original sales receipt or invoice or other satisfactory

proof of purchase. Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is non-

transferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced

Product, does not include damage to allied or associated equipment which may result for any reason from use with

this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse

(e.g. overdriving the ampliﬁer or speaker, excessive heat, cold or humidity), or from service or repair which has not been

authorized by Sonance. Obtaining Authorized Service: To qualify for the warranty, you must contact your authorized

Sonance Dealer/Installer or call Sonance Customer Service at (949) 492-7777 within the warranty period, must obtain

a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty

period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.

all features and speciﬁcations are subject to change without notice. For the latest Sonance product speciﬁcation information visit our

website: www.sonance.com

SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA

PHONE: (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (949) 492-7777 • www.sonance.com

10.24.2019

Sonance Patio Series 4.1 Manuel utilisateur

Marque: Sonance

Modèle: Patio Series 4.1

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Sonance Patio Series 4.1 User manual

Documents connexes

Sonance DSP 2-150 MKII Manuel utilisateur

Sonance Patio Series 4.1 Manuel utilisateur

Ce manuel convient également à

Sonance Patio Series 4.1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents