AccuCold FF7BADA Manuel utilisateur

Marque: AccuCold

Modèle: FF7BADA

Catégorie: Congélateurs

Taper: Manuel utilisateur

Ce manuel convient également à

Write Model and Serial Numbers here:

Écrire numéros de modèle et de série ici:

Model/Modèle: ____________________

Serial No./Série: ___________________

BUILT-IN ALL-REFRIGERATORS

RÉFRIGÉRATEURS ENCASTRÉS

Models / Modèles: FF6BI series

(ACCUCOLD®)

FF7BI series (

ACCUCOLD®)

SCR600LBI series

(ACCUCOLD®)

SCR600BLBI series (SUMMIT Commercial)

CM411L

Instruction Manual / Mode d’emploi

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS

AVANT L’EMPLOI, LIRE ET SUIVRE LES RÈGLES DE SÉCURITÉ

ET INSTRUCTIONS D'UTILISATION

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, NY 10474

www.summitappliance.com

IMPORTANT SAFEGUARDS

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential

hazards that can kill or injure you and others. All safety messages will

follow the Safety Alert Symbol and either the words ”DANGER” or

“WARNING”.

DANGER means that failure to heed this

safety statement may result in severe

personal injury or death.

WARNING means that failure to heed

this safety statement may result in

extensive product damage, serious

personal injury, or death.

Safety messages will alert you to what the potential hazard is, tell you how to reduce the chance

of injury, and let you know what can happen if the instructions are not followed.

Before the refrigerator is used, it must be properly positioned and installed

as described in this manual, so read the manual carefully. To reduce the

risk of fire, electrical shock or injury when using the appliance, follow basic

precautions, including the following:

• Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an adapter,

and do not use an extension cord.

• It is recommended that a separate circuit, serving only your refrigerator, be provided. Use

receptacles that cannot be turned off by a switch or pull chain.

• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or

explosion. And do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

• Before proceeding with cleaning and maintenance operations, make sure the power line of the

unit is disconnected.

• Do not connect or disconnect the electric plug when your hands are wet.

• Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do so

can result in electrical shock or death.

• Do not attempt to repair or replace any part of your refrigerator unless it is specifically

recommended in this material. All other servicing should be referred to a qualified technician.

• Use two or more people to move and install the refrigerator. Failure to do so can result in back

or other injury.

• To ensure proper ventilation for your appliance, the front of the unit must be completely

unobstructed. Choose a well-ventilated area with temperatures above 60

F (16

C) and below

F (32

C). This unit must be installed in an area protected from the elements, such as wind,

rain, water spray or drips.

• The appliance should not be located next to ovens, radiators or other sources of high heat.

• The appliance must be installed with all electrical connections in accordance with state and

local codes. A standard electrical supply (115V AC only, 60 Hz), properly grounded in

accordance with the National Electrical Code and local codes and ordinances, is required.

• Do not kink or pinch the power supply cord of the appliance.

• The fuse (or circuit breaker) size should be 15 amperes.

• It is important for the refrigerator to be leveled in order to work properly. You may need to

make several adjustments to level it.

• Never allow children to operate, play with or crawl inside the refrigerator.

• Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may

damage or discolor the interior.

• Do not use this apparatus for other than its intended purpose.

THE FF6BI AND FF7BI SERIES MODELS, AS WELL AS MODEL SCR600LBI, ARE DESIGNED

FOR MEDICAL OR PHARMACEUTICAL USE ONLY. THEY ARE NOT INTENDED FOR USE

AS HOUSEHOLD REFRIGERATORS. MODEL SCR600BLBI IS DESIGNED AS A

COMMERCIAL BEVERAGE MERCHANDISER.

Risk of child entrapment

Child entrapment and suffocation are not problems of the past. Junked or abandoned

refrigerators and freezers are still dangerous, even if they will “just sit in the garage a few

days.”

• Before you throw away your old refrigerator or freezer: Take off the doors. Leave

the shelves or drawers in place so that children may not easily climb inside.

• Never allow children to operate, play with, or crawl inside the refrigerator/freezer.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM

PERSONS UNLESS THEY HAVE BEEN ADEQUATELY SUPERVISED BY A RESPONSIBLE

PERSON TO ENSURE THAT THEY CAN USE THE APPLIANCE SAFELY. YOUNG CHILDREN

SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE.

- SAVE THESE INSTRUCTIONS -

Table of Contents

Important Safeguards .................................................................................................... 1 - 2

Location of Parts ............................................................................................................ 3 - 4

Technical Information ......................................................................................................... 5

Installation Instructions ................................................................................................. 6 - 8

Before Using Your Appliance .......................................................................................... 6

Installing the Refrigerator ............................................................................................... 6

Electrical Connection / Extension Cord ...................................................................... 6 - 7

Reversing the Door Swing ......................................................................................... 7 - 8

Door Handle Installation .................................................................................................. 8

Operating Your Refrigerator ............................................................................................... 9

Temperature Control

Defrosting Your Appliance

Care and Maintenance ...................................................................................................... 10

Cleaning Your Appliance / Power Failure / Vacation Time /

Moving your Appliance / Energy-Saving Tips

Troubleshooting ................................................................................................................ 11

Limited Warranty ............................................................................................................... 12

French version of this manual ................................................................................... 14 - 27

Location of Parts

Temperature control dial

(thermostat) and interior

light

Door with storage

compartments

Front ventilation

slots (kick plate)

Leveling legs

Adjustable shelves

(wire for FF6BI & FF6LBI;

glass for FF6BBI)

Defrost water

outlet

(behind crisper)

NOTE: Model FF6LBI has a lock located on the front

of the door, near the top center.

Handle

Crisper and

glass cover

FF6BI and

FF6BBI series

Temperature control dial

(thermostat), light switch

and interior light

Door

Front ventilation

slots (kick plate)

Leveling legs

Adjustable shelves

(wire for FF7BI & FF7LBI;

glass for FF7BBI &

FF7LBLBI)

Defrost water

outlet

NOTE: Lock on models FF7LBI and FF7LBLBI is located

on the front of the door, near the top center.

Handle

FF7BI and

FF7LBLBI series

Temperature control dial

(thermostat), light switch

and interior light

Glass door

Front ventilation

slots (kick plate)

Leveling legs

Adjustable shelves

(wire for SCR600LBI;

glass for SCR600BLBI)

Defrost water

outlet

Handle

SCR600LBI and

SCR600BLBI series

Lock

Technical Information

Model Numbers

and

Descriptions

FF6BI (white with wire shelves and no lock; door storage)

FF6LBI (white with wire shelves and lock; door storage)

FF6BBI (black with glass shelves and no lock; door storage)

FF7BI (white with wire shelves and no lock; flat door liner)

FF7LBI (white with wire shelves and lock; flat door liner)

FF7BBI (black with glass shelves and no lock; flat door liner)

FF7LBLBI (black with glass shelves and lock; flat door liner)

SCR600LBI (white with wire shelves and lock; glass door)

SCR600BLBI (black with glass shelves and lock; glass door)

Capacity

5.5 cu. ft.

Electrical Input

115V AC/60Hz

Rated Current

1.0A

Refrigerant

R134a (1.8 oz.)

Installation

Built-in or Freestanding

Unit Dimensions

(W x D x H)

23.63" x 23.5" x 33.5"

NOTES: 1. FF6BI and FF7BI series models and SCR600LBI are suitable for storing

vaccines, pharmaceuticals and other temperature-sensitive materials. They

can also store foodstuffs at an ideal temperature. However, they are not

designed for household use since they utilize an oversized commercial

compressor.

Model SCR600BLBI is designed as a commercial beverage merchandiser.

2. Specifications are subject to change without notice.

Improper use of the grounded plug can result in the risk of electrical shock. If the power

cord is damaged, have it replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Installation Instructions

Before Using Your Appliance

• Remove the exterior and interior packing.

• CAUTION: After unpacking you MUST allow this appliance to stand upright for at least 2

hours to allow the lubricant and refrigerant to drain back into the compressor and

stabilize. Failure to do so may adversely affect performance and the lifetime of this unit.

• Remove the shelves and clean them and the interior surfaces of the unit with

lukewarm water using a soft cloth.

Installing the Refrigerator

• Place the unit on a floor that is strong enough to support the appliance when it is fully

loaded. To level the unit, adjust the two leveling legs at the front.

• Your appliance can be installed either free-standing, recessed or built into an

enclosure. When installing as a free-standing unit, allow at least 2” (51mm) of space

at the sides, top and rear of the unit to allow for proper air circulation to cool the

compressor and condenser. Even when built in, the unit requires at least 2” of

clearance at the back, 1/8” (3mm) at both sides and 1/16” (1.6mm) at the top. Take

care that the air vents at the front of the appliance are never covered or blocked in

any way.

• Locate the unit away from direct sunlight and sources of heat (oven, heater, radiator,

etc.). Direct sunlight may affect the acrylic coating and heat sources may increase

electrical consumption. Extremely cold ambient temperatures may also affect the

unit's performance.

• Avoid locating the unit in moist areas. Too much moisture in the air will cause frost to

form quickly on the evaporator, requiring more frequent defrosting of the interior.

• Plug the unit into an exclusive, properly installed and grounded wall outlet. Do not

under any circumstances cut or remove the third (ground) prong from the power cord.

Any questions concerning power and/or grounding should be directed toward a

certified electrician or authorized service center.

Electrical Connection

This unit should be properly grounded for your safety. The power cord of this unit is

equipped with a three-prong plug which mates with a standard three-prong wall outlet to

minimize the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power

cord supplied. For personal safety, this appliance must be properly grounded.

This unit requires a standard 115-volt AC/60Hz electrical outlet with three-prong ground.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet

is properly grounded. When a standard 2-prong wall outlet is encountered, it is your

responsibility and obligation to have it replaced with a properly grounded 3-prong wall

outlet.

To prevent accidental injury, the cord should be secured behind the unit and not left

exposed or dangling.

The unit should always be plugged into its own individual electrical outlet which has a

voltage rating that matches the rating label on the appliance. This provides the best

performance and also prevents overloading house wiring circuits that could cause a fire

hazard from overheated wires. Never unplug the unit by pulling on the power cord.

Always grip the plug firmly and pull straight out from the receptacle. Repair or replace

immediately any power cord that has become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end. When

moving the unit, be careful not to damage the power cord.

Extension Cord

Do not use an extension cord with this appliance. If the power cord is too short, have a

qualified electrician or service technician install an outlet near the appliance.

Reversing the Door Swing (select models only)

If you find the direction of opening the door of the appliance inconvenient, you can

change it. Holes on the opposite side have already been prepared at the factory.

This appliance can be opened from either the right side or the left. By default, the door

hinge is on the right side. If you prefer it on the left, please follow the appropriate

instructions:

For models FF6BBI, FF7BI and FF7BBI

1. Take off the upper hinge cover from the door and remove the screws that hold the top

hinge.

2. Lift the hinge straight up to free the hinge pin from the socket in the top of the door.

3. Lift the door up and away to free its bottom socket from the hinge pin.

4. Remove the screws to the bottom hinge.

5. Remove the decorative caps from the opposite side and plug the holes from the

original side with the decorative caps.

6. Move the bottom hinge to the opposite side and tighten the screws. Use any lock

washers or nuts if they were installed in the original installation.

7. Replace door onto the hinge pin on the bottom hinge. Place top hinge pin into door.

Insert screws into the top hinge and tighten.

If you notice the door not hanging straight, loosen the top hinge screws, adjust the door

until it is level and tighten the screws.

For models FF6BI, FF6LBI, FF7LBI, FF7LBLBI, SCR600LBI and SCR600BLBI

NOTES: See illustration below.

All of the parts that are removed must be kept for the reinstallation of the door.

1. Unscrew the lower hinge and take off the door.

2. Push the kick plate to the right in the new position.

3. Undo the upper hinge fastener and fix it to the opposite side of the housing, where you

have already removed and replaced the fastener with the hole to the opposite side.

4. Put the door on the upper hinge fastener.

5. Fix the lower hinge in the new position.

6. Unscrew the handle and place it on the opposite side.

7. Some screws are covered with caps. Take off these caps before undoing the screws.

8. Check the door gasket. It should not be creased and should seal well.

1. Upper hinge fastener 4. Handle

2. Lower hinge 5. Door hinge fixture

3. Kick plate 6. Door hinge fixture plug

Door Handle Installation

The door has two screw holes on each side, allowing you to install a handle (included). To

do so, align the handle with the screw holes on the side you prefer. Fix the handle in place

with the included screws, then cover the screw heads with the handle seal (included).

Models FF6BI, FF6LBI,

FF7LBI, FF7LBLBI,

SCR600LBI and

SCR600BLBI

Operating Your Refrigerator

Temperature Control

• Your appliance’s evaporator system is out of sight behind the interior rear wall.

• The interior temperature is controlled with a thermostat knob

located inside the unit, towards the upper right-hand corner.

Turn the knob clockwise from the STOP (0) position toward

the higher numbers for colder temperatures. Higher settings

on the knob (higher numbers) mean lower temperatures

(colder) in the refrigerator.

• On the coldest settings, temperatures in some spots inside

the cabinet may drop below 32°F. Use higher thermostat settings only when required

or recommended. When the ambient temperature is normal, we recommend a

medium setting.

• Changes in the ambient temperature affect the temperature inside the refrigerator so

choose an appropriate setting of the thermostat knob, depending on ambient

conditions.

• In the STOP (0) position, the appliance does not operate (the cooling system is

switched off), yet the power supply is not interrupted (the light still works).

• Temperature inside the refrigerator also depends on how often you open the door.

• In all small refrigerators without interior fans, temperatures are coldest near the

bottom, and occasionally near the rear. Place contents accordingly. It is best not to

operate these units mostly empty. If temperatures are erratic, try putting some water

bottles inside to create a load for the compressor.

NOTES:

1. Shelves are adjustable. Certain models include glass shelves (see Technical

Information, page 5). These shelves stop short an inch before the back wall, which is

essential for air flow and the proper operation of the automatic defrost system. Do not

block these gaps.

2. a) Interior lighting on the FF6BI series models is controlled by a switch that is

activated by the opening and closing of the refrigerator door.

b) Lights in the other series models are controlled by a manually-operated rocker

switch. To maintain the proper interior temperature, keep the light on only as long

as necessary. Leaving the light on for long periods of time may damage stored

contents.

3. If the refrigerator is unplugged, has lost power, or is turned off, you must wait 3 to 5

minutes before restarting it. If you attempt to restart before this time delay, the unit will

not start.

Defrosting Your Appliance

This appliance operates with an automatic defrost system, so the refrigerator defrosts

itself. While the compressor is operating, ice will build along the rear cold wall (the

evaporator plate is behind the wall). During the compressor’s off-cycle, ice will melt, drip

down, collect in the trough at the bottom and drain through a small hole into a tray above

the compressor; where the compressor’s heat will evaporate the water. If you notice

excessive ice build-up on the rear wall, try setting the thermostat to a slightly warmer

setting; be sure that the door gasket is sealing well and that there is no obstruction of the

drain hole at the bottom rear of the interior cabinet.

Care and Maintenance

Cleaning Your Appliance

1. Unplug the appliance, turn the thermostat to STOP (0) and remove all contents,

including shelves.

2. Wash the inside surfaces with a solution of lukewarm water and vinegar. Wipe dry

with a clean, soft cloth.

3. Wash the shelves, drip tray and crisper (if present) with a mild detergent solution,

then rinse and dry thoroughly.

4. Wash the outside cabinet with a solution of warm water and mild liquid detergent.

Rinse well and wipe dry with a clean soft cloth.

5. Wring excess water out of the sponge or cloth before cleaning the area of the

temperature control or any electrical parts.

6. From time to time, wipe the condenser on the rear wall with a soft

non-metallic brush or vacuum cleaner.

7. After you have cleaned the appliance, reconnect it to the power

supply, reset the thermostat and return all contents to their place.

CAUTION: Failure to unplug the unit could result in electrical shock or

personal injury.

Power Failure

Most power failures are corrected within a few hours and should not affect the

temperature of your appliance if you minimize the number of times the door is opened. If

the power is going to be off for a longer period of time, you need to take the proper steps

to protect your frozen and chilled items.

Vacation Time

During long absences, remove all contents. Unplug the appliance, clean it and leave the

door open slightly to avoid possible formation of condensation, mold or odors.

Moving Your Appliance

1. Remove the contents.

2. Securely tape down all shelving inside your unit.

3. Turn the leveling legs up to the base to avoid damage.

4. Tape the door shut.

5. Be sure the appliance stays secure in the upright position during transportation.

Energy-Saving Tips

• The unit should be located in the coolest area of the room, away from heat-producing

appliances or heating ducts and out of direct sunlight.

• Try not to open the door too often, especially when the weather is damp and hot.

Once you open the door, close it as soon as possible.

• Occasionally check if the appliance is sufficiently ventilated (adequate air circulation

behind the appliance).

• Set the thermostat from higher to lower settings as soon as possible (depending on

how loaded the appliance is, ambient temperature, etc.).

• Before loading items into the unit, be sure they have cooled to ambient temperature.

Troubleshooting

When using this appliance, you may come across some problems that in many cases

result from improper handling and can easily be eliminated.

TROUBLESHOOTING GUIDE

The appliance fails to operate after being connected to the power source.

• Check whether the power supply is active and that the thermostat is not set to the

STOP (0) position.

The compressor is running continuously.

• The door was opened frequently or it was left open too long.

• The door is not properly closed (the door may sag, the gasket may be dirty or

damaged).

• The power supply has been interrupted for a long period of time.

• The appliance may have been overloaded with items above room temperature.

• There may be inadequate ventilation of the compressor and condenser. (Assure

there is adequate air circulation behind the appliance and wipe the dust from the

condenser.)

Noise

• Cooling in refrigeration appliances is enabled by the refrigerating system with a

compressor, which produces noise. How noisy the appliance is depends on where

it is placed, how it is used and how old the appliance is.

• During the operation of the compressor, the noise of liquid is heard and when the

compressor is not operating, the refrigerant flow is heard. This is a normal

condition and has no influence whatsoever on the lifetime of the appliance.

• After starting the appliance, the operation of the compressor and the refrigerant

flow may be louder. This does not mean that something is wrong. Gradually the

noise is reduced.

• Sometimes a louder noise is heard, which is unusual for the appliance. This noise

is often a consequence of improper placement of the unit. (The unit should be

placed and leveled firmly on a solid base and it should not touch the wall or

cabinets standing next to it.)

For parts and accessory ordering,

troubleshooting and helpful hints, visit:

www.summitappliance.com/support

Limited Warranty

Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is

operated and maintained according to instructions attached to or furnished with the product, warrantor will

pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must

be provided by a designated service company. Outside the 48 states, all parts are warranted for one year

from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to

commercially acceptable standards, and are not covered from damage during handling or breakage.

ONE-YEAR LIMITED WARRANTY

1. The compressor is covered for 5 years.

5-YEAR COMPRESSOR WARRANTY

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to

replace or repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as

filters) are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper

installation, installation not in accordance with electrical or plumbing codes, or use of products not

approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. Expenses for travel and transportation for product service in remote locations.

7. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not

installed in accordance with published installation instructions.

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.

WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY

FROM STATE TO STATE.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, NY 10474

Phone: (718) 893-3900

Fax: (844) 478-8799

www.medicalrefrigerators.com

Printed in the USA

WARNING! This product may contain chemicals known to the state of California to

cause cancer or birth defects or other reproductive harm. For more information, visit:

www.summitappliance.com/prop65

Chemicals known by the manufacturer to be present in this product in concentrations

higher than threshold limits: NONE.

Notes

Mesures de sécurité importantes

Votre sécurité et celle des autres est très importante pour nous. Nous avons

fourni plusieurs messages de sécurité importants dans ce manuel. Toujours lire

et suivre les consignes de sécurité. Des blessures graves ou même la mort

peuvent survenir si vous ne suivez pas ces instructions. Tous les messages de

sécurité vous diront quel est le danger potentiel, comment réduire le risque de

blessure et ce qui peut arriver si les instructions ne sont pas suivies.

ATTENTION! Pour réduire le risque d'incendie, de choc électrique ou de blessure

lors de l'utilisation de votre appareil, suivre ces précautions essentielles:

• Utiliser deux ou plus de personnes pour déplacer et installer cet appareil.

• Brancher sur une prise à 3 broches mise à la terre.

• Ne pas enlever la broche mise à la terre, ni utiliser un adaptateur 3/2.

• L'appareil doit être installé avec toutes les connexions électriques en

conformité avec les codes nationaux et locaux. Une alimentation électrique

standard (115V CA seulement, 60 Hz), correctement mise en conformité avec

le National Electrical Code et les codes et règlements locaux, est nécessaire.

• Ne pas plier ou pincer le cordon d'alimentation de l'appareil.

• La taille du fusible (ou disjoncteur) doit être de 15 ampères.

• Ne pas utiliser une rallonge.

• Veiller à ne pas brancher dans les prises contrôlées par des interrupteurs

muraux.

• Le réfrigérateur doit être nivelé afin de fonctionner correctement. Vous pouvez

avoir besoin de faire plusieurs ajustements pour y arriver.

• Pour assurer une bonne ventilation de votre appareil, l'avant de l'appareil doit

être complètement dégagée. Choisissez un endroit bien aéré avec des

températures supérieures à 60°F (16°C) et en dessous de 90°F (32°C).

• Cet appareil doit être installé dans un endroit protégé des éléments, tels que

le vent, la pluie, de l'eau pulvérisée ou gouttes.

• L'appareil ne doit pas être situé à proximité de fours, grilles ou d'autres

sources de chaleur intense. Gardez-le hors des rayons directs du soleil.

• Coupez l'alimentation avant l'entretien.

• Après le service, remplacer toutes les pièces et panneaux avant de faire

fonctionner.

• Ne pas stocker ou utiliser de l'essence ou d'autres produits inflammables dans

le domaine de ce ou tout autre appareil, comme les émanations peuvent

provoquer un risque d'incendie ou d'explosion.

• Utiliser des nettoyants non inflammables.

• Lors du remplacement d'une ampoule, débranchez l'appareil ou coupez le

courant au disjoncteur ou la boîte à fusibles afin d'éviter de toucher un fil sous

tension. Pour les modèles avec thermostats à cadran, tourner le thermostat à

STOP (0) (Arrêt) coupe le compresseur, mais ne coupe pas l'alimentation des

autres composants électriques.

• Ne débranchez jamais votre appareil en tirant sur le cordon d'alimentation.

Tenez toujours la fiche fermement et tirer tout droit sorti de la prise.

• Veillez à ne pas écraser ou endommager le cordon pour déplacer l'appareil.

• Ne vous pincer pas, nouer ou plier le cordon d'alimentation de toute manière.

• Remplacer ou réparer un cordon de service électrique qui a été endommagé

ou effiloché.

• Débranchez l'appareil avant d'effectuer des réparations ou le nettoyage. Nous

recommandons que le service soit effectué par un technicien qualifié.

• Si votre électricité s'éteint, suivez cette procédure:

 Appelez votre compagnie d'électricité pour déterminer combien de temps

le service doit être interrompu.

 Si le service doit être interrompu pendant moins de 24 heures, garder

l'appareil fermé autant que possible. Cela permettra de garder le contenu

de se gâter.

 Si le service doit être interrompu pendant plus de 24 heures, retirer le

contenu et stocker dans un casier réfrigéré ou autre réfrigérateur.

DANGER! Risque de piégeage d’enfants!

Les anciens appareils peuvent représenter un danger d'étouffement pour les

enfants.

• Enlevez la porte(s) de votre ancien appareil.

• Laissez les étagères ou des paniers en place.

• Si votre ancien appareil contient des fluides frigorigènes, il doit être recyclé

par une agence agréée de service ou d’élimination des déchets.

LES SÉRIES DE MODÈLES FF6BI ET FF7BI, AINSI QUE LA SÉRIE

SCR600LBI, SONT CONÇUES POUR USAGE MÉDICAL OU

PHARMACEUTIQUE SEULEMENT. ELLES NE SONT PAS DESTINÉES À

SERVIR DE RÉFRIGÉRATEURS. MODÈLE SCR600BLBI EST CONÇU

COMME UN MARCHANDISEUR DES BOISSONS COMMERCIAL.

CET APPAREIL N’EST PAS DESTINÉ À L'USAGE DES JEUNES ENFANTS OU

DES PERSONNES HANDICAPÉES À MOINS QU’ILS AIENT ÉTÉ

ADÉQUATEMENT SUPERVISÉS PAR UNE PERSONNE RESPONSABLE DE

FAÇON QU’ILS PUISSENT UTILISER LES APPAREILS EN TOUTE

SÉCURITÉ. LES JEUNES ENFANTS DOIVENT ÊTRE SURVEILLÉS POUR

ÉVITER QU’ILS NE PAS JOUER AVEC L’APPAREIL.

̶ CONSERVER CES INSTRUCTIONS ̶

Table des matières

Mesures de sécurité importantes ................................................................. 14 – 15

Emplacement des pièces .............................................................................. 16 – 17

Informations techniques ....................................................................................... 18

Instructions d’installation .............................................................................. 18 - 21

Avant d’utiliser votre appareil ............................................................................ 18

Installation du réfrigérateur ......................................................................... 18 - 19

Raccordement électrique ............................................................................ 19 - 20

Rallonge ............................................................................................................ 20

Inversion de l’ouverture de la porte ............................................................ 20 - 21

Installation de la poignée de porte ..................................................................... 21

Fonctionnement de votre réfrigérateur ......................................................... 22 - 23

Régulation de la température ............................................................................ 22

Dégivrage de votre appareil .............................................................................. 23

Entretien et maintenance ............................................................................... 23 - 24

Nettoyage de votre appareil / Panne de courant / Vacances ............................. 23

Déplacement de votre appareil / Conseil d’économie d’énergie ........................ 24

Dépannage ............................................................................................................. 25

Garantie limitée ...................................................................................................... 27

Emplacement des pièces

FF6BI

Cadran de réglage de

température

(thermostat) et

l'éclairage intérieur

Porte avec compartiments

de stockage

Fentes

d'aération avant

(

plaque de

protection)

Pieds de

nivellement

Étagères réglables

(fil pour FF6BI et FF6LBI;

verre pour FF6BBI)

Sortie de l'eau de

dégivrage

(derrière le bac)

REMARQUE: Le modèle FF6LBI a une serrure située

à l'avant de la porte, près du centre supérieur.

Poignée

Bac et

couverture

en verre

Séries FF6BI

et FF6BBI

Séries FF7BI et FF7LBLBI

Séries SCR600LBI et SCR600BLBI

Cadran de réglage de

température (thermostat),

interrupteur de lumière,

et lumière intérieure

Porte

Fentes

d'aération avant

(

plaque de

protection)

Pieds de

nivellement

Étagères réglables

(fil pour FF7BI

et FF7LBI

;

verre pour FF7BBI

et FF7LBLBI)

Sortie de l'eau

de dégivrage

NOTE: La serrure des modèles FF7LBI et FF7LBLBI est

située sur la face de la porte, à proximité de la partie

centrale supérieure.

Poignée

Cadran de réglage de

température

(thermostat),

interrupteur

de lumière, et lumière

Porte en verre

Fentes

d'aération avant

(

plaque de

protection)

Pieds de

nivellement

Étagères réglables

(fil pour SCR600LBI;

verre pour SCR600BLBI)

Sortie de l'eau

de dégivrage

Poignée

Serrure

Informations techniques

Numéros de

modèles et

descriptions

FF6BI (blanc avec étagères de fil et pas de serrure; stockage à la porte)

FF6LBI (blanc avec étagères de fil et serrure; stockage à la porte)

FF6BBI (noir avec étagères en verre et pas de serrure; stockage à la porte)

FF7BI (blanc avec des étagères de fil et pas de serrure; intérieur de la porte plat)

FF7LBI (blanc avec étagères de fil et serrure; intérieur de la porte plat)

FF7BBI (noir avec étagères en verre et pas de serrure; intérieur de la porte plat)

FF7LBLBI (noir avec étagères en verre et serrure; intérieur de la porte plat)

SCR600LBI (blanc avec étagères de fil et serrure; porte en verre)

SCR600BLBI (noir avec étagères en verre et serrure; porte en verre)

Capacité

5.5 pieds cubiques (156 litres)

Entrée électrique

115V CA/60Hz

Ampérage

1.0A

Réfrigérant

R134a , 1.8 oz. (51,0 g))

Installation

Encastrée ou autonome

Dimensions de

l’unité (L x P x H)

23.63" x 23.5" x 33.5" (60,0 x 59,7 x 85,1 cm)

Instructions d’installation

Avant d'utiliser votre appareil

• Retirez l'emballage extérieur et l'intérieur.

• ATTENTION: Après le déballage vous DEVEZ permettre cet appareil de se tenir

debout pendant au moins 2 heures pour permettre aux lubrifiant et réfrigérant à écouler

dans le compresseur et se stabiliser. Ne pas le faire peut affecter les performances et la

durée de vie de cette unité.

• Retirez les étagères et les nettoyer et les surfaces intérieures de l'appareil

avec de l'eau tiède et un chiffon doux.

Installation du réfrigérateur

• Placez l'appareil sur un plancher qui est assez solide pour supporter l'appareil

quand il est entièrement chargé. Pour mettre à niveau l'unité, réglez les deux

pieds de nivellement à l'avant.

• Votre appareil peut être installé soit en position libre, encastré ou intégré dans

une enceinte. Lors de l'installation comme une unité autonome, permettre au

moins 2 " (51mm) d'espace sur les côtés, en haut et à l'arrière de l'appareil

NOTES : 1. Les séries des modèles SCR600LBI, FF6BI et FF7BI sont adaptées pour stocker les

vaccins, les produits pharmaceutiques et d'autres matériaux sensibles à la température. Ces

modèles peuvent également stocker des denrées alimentaires à une température idéale.

Cependant, ils ne sont pas conçus pour un usage domestique, car ils utilisent un

compresseur commercial surdimensionné.

Modèle SCR600BLBI est conçu comme un marchandiseur des boissons commercial.

2. Les spécifications sont sujettes à modification sans préavis.

Une mauvaise utilisation de la fiche de terre peut entraîner un risque de choc électrique.

Si le cordon d'alimentation est endommagé, le faire remplacer par le fabricant, son

agent de service ou un technicien qualifié afin d'éviter un danger.

pour permettre une bonne circulation d'air pour refroidir le compresseur et le

condenseur. Même quand intégré, l'appareil nécessite au moins 2 " de

dégagement à l'arrière, 1/8" (3 mm) des deux côtés et 1/16 " (1,6 mm) dans la

partie supérieure. Veillez à ce que les grilles d'aération à l'avant de l'appareil

ne sont jamais couvertes ou bloquées en aucune façon.

• Installez l'appareil loin de la lumière du soleil directe et des sources de chaleur

(four, chauffage, radiateur, etc.). La lumière solaire directe peut affecter le

revêtement acrylique et sources de chaleur peut augmenter la consommation

électrique. Des températures ambiantes extrêmement froides peuvent

également affecter la performance de l'appareil.

• Éviter de placer l'appareil dans les zones humides. Trop d'humidité dans l'air

provoque la gelée à former rapidement sur l'évaporateur, ce qui nécessite un

dégivrage plus fréquent de l'intérieur.

• Branchez l'appareil dans une prise murale exclusive, correctement installée et

mise à la terre. Ne pas en aucun cas réduire ou supprimer le troisième pôle

(terre) du cordon d'alimentation. Toutes les questions concernant la puissance

et / ou mise à la terre doivent être adressées à un électricien certifié ou au

centre de service autorisé.

Raccordement électrique

Cet appareil doit être correctement mis à la terre pour votre sécurité. Le cordon

d'alimentation de cet appareil est équipé d'une fiche à trois broches qui

s’accouple avec une prise murale standard à trois broches afin de minimiser le

risque de choc électrique.

Ne pas en aucun cas couper ou enlever la troisième broche de terre du cordon

d'alimentation fourni. Pour votre sécurité, cet appareil doit être correctement mis

à la terre.

Cette unité nécessite une norme électrique de 115 volts CA / 60Hz avec une

prise à terre à trois broches. Avoir la prise murale et le circuit vérifiés par un

électricien qualifié pour s’assurer que la prise est correctement mise à la terre.

Quand une prise murale standard à 2 broches est rencontrée, il vous incombe de

la faire remplacer par une prise murale à 3 broches mise à la terre.

Pour éviter toute blessure accidentelle, le cordon doit être fixé derrière l'unité et

non laissé exposé ou pendant.

L'unité doit toujours être branchée dans sa propre prise électrique qui a une

tension qui correspond à la plaque signalétique de l'appareil. Cette offre les

meilleures performances et empêche aussi la surcharge des circuits de câblage

qui pourrait provoquer un risque d'incendie par surchauffe des fils. Ne

AVERTISSEMENT

La page charge ...

AccuCold FF7BADA Manuel utilisateur

Marque: AccuCold

Modèle: FF7BADA

Catégorie: Congélateurs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: AccuCold FF7BADA User manual

AccuCold FF7BADA Manuel utilisateur

Ce manuel convient également à

AccuCold FF7BADA Manuel utilisateur

dans d''autres langues

Documents connexes