GE Monogram ZIBI240HII Guide d'installation

Catégorie
Frigos
Taper
Guide d'installation
Design Guide with
Installation
Instructions
Fresh-Food Refrigerator
ZIFI240
ZIFS240
Bar Refrigerator with Icemaker
ZIBI240
ZIBS240
monogram.com
2
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANTSave these instructions for
local inspector’s use. Observe all governing codes
and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These
words are defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
For Monogram local service in your area, call 1.800.444.1845.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.800.626.2002.
www.monogram.com
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in
fire, explosion, or death.
WARNING
To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-prong
(grounding) plug which mates with a standard 3-prong (grounding)
wall outlet to minimize the possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced with a
properly grounded 3-prong wall outlet. Do not use an adapter.
The refrigerator should always be plugged into its own individual
electrical outlet which has a voltage rating that matches the rating
plate.
A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical
supply is required. This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on
the power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the refrigerator away from the wall,
be careful not to roll over or damage the power cord.
CONNECTING ELECTRICITY
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet
Do not remove the ground prong
Do not use an adapter
Failure to follow these instructions can result in
death, fire, or electrical shock.
3
AVERTISSEMENT
Risque d’explosion.
Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-
respect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.
AVERTISSEMENT
Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les
petites pièces à la portée des enfants âgés de moins de 3 ans.
Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des
blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots «
DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants :
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles
sures graves, voire la mort.
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures graves, voire la mort. .
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures mineures ou graves.
AVERTISSEMENT
DANGER
ATTENTION
Consignes de Sécurité
Ne coupez pas ou n’enlevez pas, sous aucun prétexte, la troisième broche de mise à la terre du cordon d’alimentation.
Pour des raisons de sécurité, cet appareil doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est équipé d’une fiche
à trois broches (pour une mise à la terre) qui s’adapte à la prise
de courant standard à 3 broches (pour une mise à la terre) pour
minimiser les risques de chocs électriques par cet appareil.
Faites vérifier la prise murale et le circuit électrique par un
électricien qualifié pour s’assurer que le système est correctement
mis à la terre.
Dans le cas d’une prise biphasée, l’installateur a la responsabilité
et l’obligation de la remplacer par une prise triphasée
correctement mise à la terre. N’utilisez pas d’adaptateur.
Le réfrigérateur doit toujours être branché à sa propre prise
électrique d’une tension nominale correspondant à celle indiquée
sur sa plaque signalétique.
Une alimentation électrique à 115 volts CA, 60 Hz, avec un fusible
de 15 ou 20 ampères et une mise à la terre est nécessaire. Ceci
permet d’obtenir un meilleur rendement et évite de surcharger
les circuits électriques du domicile qui risque d’occasionner un
incendie en surchauffant.
Ne débranchez jamais le réfrigérateur en tirant sur le cordon
d’alimentation. Prenez toujours fermement la fiche en main et
tirez pour la sortir de la prise.
Réparez ou remplacez immédiatement tout
cordon électrique usé ou endommagé. N’utilisez
pas un cordon fissuré ou présentant des
dommages dus aux frottements soit sur sa
longueur ou aux extrémités.
Lorsque vous éloignez votre réfrigérateur du
mur, faites attention à ne pas le faire rouler
sur le cordon d’alimentation afin de ne pas
l’endommager.
BRANCHEMENTS ÉLECTRIQUES
AVERTISSEMENT
Risque de choc électrique.
Branchez l’appareil dans une prise triple avec terre.
Ne retirez pas la broche de terre.
N’utilisez pas d’adaptateur.
Le non-respect de ces instructions peut entraîner des risques d’incendies, des chocs électriques ou la mort.
4
CARING FOR YOUR STAINLESS STEEL
Before installation or first use, we strongly advise that
you polish the stainless steel exterior and handle with
a commercially available stainless steel cleaner such as
Stainless Steel Magic.
To preserve and protect the fine
finish, we also strongly advise that you apply stainless
steel cleaner monthly.
STAINING WOOD DRAWER FRONTS
The drawer fronts are unfinished cherry wood. During use,
oil from hands may accumulate and stain the wood.
• The drawer fronts may be stained and sealed to match
adjacent cabinetry.
Apply the stain and sealer according to the manufacturer’s
instructions. To avoid unpleasant odor, keep the door open
to ventil ate and allow the stain/sealer to dry completely
before using the product.
CONTENTS
Important Information ...................................................................................2, 3
Parts Required ............................................................................................................4
Caring for Your Stainless Steel ..........................................................................4
Tools, Hardware .......................................................................................................4
Staining Wood Drawer Fronts .........................................................................4
Install Water Line .....................................................................................................4
Design Guide (For ZIFS240 and ZIBS240)
The Installation Space ............................................................................................5
Side-by-Side Installations ...................................................................................6
Product Clearances .................................................................................................6
Design Guide (For ZIFI240 and ZIBI240)
The Installation Space ............................................................................................7
Side-by-Side Installations ...................................................................................7
Product Clearances .................................................................................................7
Installation Instructions
Step 1, Remove Packaging and Installation Parts ................................8
Step 2, Reversing the Door (ZIFI240 models only) .........................8-10
Step 3, Install Custom 3/4” Door Panel and Handle
(ZIFI240 and ZIBI240 models only) .......................................................11, 12
Step 4, Leveling .......................................................................................................12
Step 5, Connect Water Supply
(ZIBI240 and ZIBS240 models only) ..........................................................12
Step 6, Connect Power .......................................................................................13
Step 7, Slide Product into Cutout ..................................................................13
Step 8, Set Temperature Controls ................................................................13
TOOLS/HARDWARE REQUIRED
• Adjustable wrench
• Carpenter’s glue (ZIFI240 and ZIBI240 models only)
• Screwdriver (ZIFI240 and ZIBI240 models only)
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 20 and
120 p.s.i.
• The water line can enter the opening through the
floor or back wall. Route 1/4” O.D. copper tubing or
GE SmartConnect
kit between the cold water line and water
connection location, long enough to extend to the front of the
refrigerator.
• Install an optional water filter in the water line near the
refrigerator. A water filter is recommended in areas where
the water supply contains sand and particles. Installation
Instructions are packed with the filter.
NOTE: The only GE approved plastic tubing is supplied in
the GE SmartConnect
Refrigerator Tubing kits. Do not use
any other plastic water supply line because the line is under
pressure at all times. Other types of plastic may crack or
rupture with age and cause water damage to your home.
GE SmartConnect
Refrigerator Tubing Kits are available in the
following lengths:
2c (0.6 m) WX08X10002 15c (4.6 m) WX08X10015
6c (1.8 m) WX08X10006 25c (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line of
water.
• Install a shut-off valve (required) between the icemaker water
valve and cold water pipe in a basement or cabinet. The shut-
off valve should be located where it will be easily accessible.
• Turn on the main water supply and flush debris. Run about
a quart of water through the tubing into a bucket. Shut off
water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many water
supply kits, but are not recommended for this application.
NOTE: Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and use
is not permitted in Massachusetts. Consult with your licensed
plumber.
INSTALL WATER LINE (ZIBI240 AND ZIBS240 MODELS ONLY)
Floor
Water Line
Shaded Area
1-1/2"
min.
1/2"
9"
max.
10-1/2"
Water Line
PARTS REQUIRED
• Custom handle
Assembled overlay panel
• Screws
PARTS SUPPLIED
• Handle side trim
• Optional black or
stainless steel toekick
ZIFI240 AND ZIBI240 MODELS ONLY
Installation Instructions
THE INSTALLATION SPACE THE INSTALLATION SPACE (cont.)
*
For a standard installation: The product must be installed so that the
stainless steel front will project 1-5/8” forward of adjacent cabinets.
This position will allow a full door swing and prevent interference with
adjacent cabinetry. The opening between cabinets must be 23-3/4”
minimum.
** For a flush installation: Install a 1/4”-wide filler strip on the hinge
side. The filler strip will act as a spacer between the door case and
adjacent cabinets and will prevent interference with the cabinet
door swing. Recess the filler strip 1-5/8” back from the front face
of the refrigerator, or even with the front edge of the product case
(behind the gasket). The width of the opening must be 24” (including
the 1/4” filler strip).
• All models may be used freestanding.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located
on rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
5
NOTE:
Handle and
handle standoff
depth is 2-1/4”.
For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles
NOTE:
Water line location for
ZIBS240 model only
Design Guide
These products will fit flush to
adjacent cabinets when installed with
a 1/4” filler panel or cleat. The filler
panel should be recessed or set back
behind the door and even with the
front edge of the product case.
In a standard installation, the product
will project forward of adjacent
cabinets. See Dim. A.
Product Dim. A
ZIFS240 1-5/8”
ZIBS240 2-5/8”
Flush
Installation
Standard
Installation
Filler panel or cleat to be set
back even with front of case.
Front edge of product case
Front face
Front edge of product case
Front face
1/4”
110°
120°
CABINET CABINET
CABINET CABINET
110°
120°
Dim. A
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
• Allow 14” minimum clearance on the hinge side for a
full 110° door swing.
• Allow 4” min. clearance on the hinge side for the 90°
door swing and to allow racks to slide out.
NOTE: Clearances are based on the recommended 2-1/4”
handle standoff depth.
NOTE: Right-hand models illustrated. Allow the same
clearances on the opposite side for left-hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
ZIBS240 are not available with left-hand door swing.
• Test the door swing. Carefully open and close the door.
The door should not rub or catch on adjacent cabinetry.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for air
circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
• These products are not designed to be stacked one
over the other.
6
14" Minimum to Wall
110
110 Door
Swing
21-5/8"
23-5/8"
4" Minimum to Wall
90
90 Door
Swing
For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles
Design Guide
SIDE-BY-SIDE INSTALLATIONS
For a complete refreshment center, install a Fresh-
Food Refrigerator beside a Double-Drawer Refrigerator,
Beverage Center or Wine Chiller/Wine Reserve. Or, install
a Refrigerator with Icemaker beside a Wine Chiller/Wine
Reserve.
• A side-by-side installation requires at least a 47-1/2”-
wide minimum opening for standard installation and
48”-wide minimum opening for flush installation. No
trim kits required.
• Products must operate from separate, properly
grounded receptacles.
NOTE: If installing between
frameless cabinets, a 1/2”
wide filler strip or side panel
may be needed on the hinge
side. The filler strip will act as
a spacer between the door
case and adjacent cabinet
and will prevent interference
with the cabinet door swing.
The width of the opening
must include the filler panels.
THE INSTALLATION SPACE
The product must be installed so that the custom panel front will
project 2-3/4” forward of adjacent cabinets. This position will allow
a full door swing and prevent interference with adjacent cabinetry.
The opening between cabinets must be 23-3/4” minimum. These
models can not be installed flush in 24”-deep cabinets.
• All models may be used freestanding.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located
on rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
Black or Stainless Steel Toekick Options
These products are shipped with a stainless steel toekick
and a black toekick. For shipping purposes, one of the
toekicks will be secured to the back of the unit, and the
second will be installed on the unit. Keep the unused
toekick and any unused parts for future use.
7
For models ZIFI240 and ZIBI240 with Custom Door Panels and Handles
NOTE:
Water line location for
ZIBI240 model only
Design Guide
Standard
Installation
Front edge of
product case
Front face
CABINET
CABINET
110°
120°
Dim. A
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
• Allow 16” minimum clearance on the hinge side for a
full 110° door swing.
• Allow 4-1/2” min. clearance on the hinge side for the
90° door swing and to allow racks to slide out.
NOTE: Custom handle clearances may vary.
NOTE: Right hand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
ZIBS240 are not available with left hand door swing.
Test the door swing. Carefully open and close the door.
The door should not rub or catch on adjacent cabinetry.
NOTE: When installing custom panel and handle,
use above clearances as a general guide but adjust
according to the installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for air
circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
• These products are not designed to be stacked one
over the other.
16" Minimum to Wall
110
110 Door
Swing
21-5/8"
23-5/8"
4-1/2" Minimum to Wall
90
90 Door
Swing
SIDE-BY-SIDE INSTALLATIONS
For a complete refreshment center, install a Fresh-
Food Refrigerator beside a Double-Drawer Refrigerator,
Beverage Center or Wine Chiller/Wine Reserve. Or, install
a Refrigerator with Icemaker beside a Wine Chiller/Wine
Reserve.
• A side-by-side installation requires at least a 47-1/2”-
wide opening. No trim kits required.
• Products must operate from separate, properly
grounded receptacles.
34-1/2"-35"
47-1/2" Min.
1-1/2"
9"
10-1/2"
9"
10-1/2"
14"
15"
Locate
Outlet
24"
In a standard installation, the product
will project forward of adjacent
cabinets. See Dim. A.
Product Dim. A
ZIFI240 2-3/4”
ZIBI240 2-5/8”
8
STEP 1 REMOVE PACKAGING
AND INSTALLATION PARTS
• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective
plastic coverings.
Remove the toekick attached to the back of the unit.
Remove the custom panel attached to the front of
the unit.
WARNING
Small objects are a choke hazard
for children. Remove and discard any parts not used.
AVERTISSEMENT
Les petits objets peuvent étrangler
les enfants. Il faut jeter toutes les pièces qui ne sont pas
utilisées.
Installation Instructions
STEP 2 REVERSING THE DOOR
(ZIFI240 model only)
Remove top hinge and discard. Hold the door in
place.
Remove the black screw-hole cover from top left of
cabinet and insert in top right.
Remove the top trim cover and discard.
Remove 4 screws to remove the top door trim (do NOT
discard).
Remove the top hinge pin (do NOT
discard).
Flip the door 180 degrees.
Remove 3 screws to remove the bottom door trim (do
NOT discard)
Remove 2 screws to remove the door stop and discard
door stop.
Remove 1 screw to remove the bottom hinge pin and
discard hinge pin.
NOTE: Make sure the door is upside down so what was
the bottom is now the top.
Insert the top hinge pin.
Install top door trim onto the new top side of the door.
Install the new top trim cover that snaps into place.
Flip the door 180 degrees.
STEP 2 REVERSING THE DOOR
(ZIFI240 model only)
9
Installation Instructions
Install the new left bottom hinge pin and new door
stop that are enclosed in the hardware bag.
Install the bottom trim onto the new bottom side of
the door.
Remove 2 screws to remove the toe kick (do NOT
discard).
Remove 4 screws to remove the
bottom right hinge (discard the
hinge).
Install bottom left hinge that is
enclosed in hardware bag with
existing screws.
Remove the plastic cap from the top left corner of the
toe kick and discard.
Attach the new plastic cap that
is enclosed in the hardware bag
to the top right corner of the toe
kick.
Reinstall toe kick to unit with 2
existing screws.
To install the door, set the door
onto the left bottom hinge pin.
Holding the door in place, insert
the new top left hinge pin into
the door and secure the hinge
to the case with screws.
STEP 2 REVERSING THE DOOR
(ZIFI240 model only) (Cont.)
STEP 2 REVERSING THE DOOR
(ZIFS240 model only)
Remove top hinge and discard. Hold the door in
place.
Remove the black screw-hole cover from top left of
cabinet and insert in top right.
Remove 2 screws tor remove the toekick (do not
discard).
Remove bottom right hinge and discard the hinge.
Keep the screw for installation of the new hinge.
Attache the bottom left hinge with the screw from the
previous step.
Move the plug on the toekick from the left to the right
and reattach toekick to the unit.
10
Installation Instructions
Remove top plug/bushing from the door using a flat
head screwdriver. Discard the bushing.
Rotate the door 180°.
Remove the screw from the plug/bushing on the
bottom of the door. Discard the plug/bushing but keep
the screw.
Remove the black screw post from the bottom of the
door using a flat head scewdriver. Keep the screw
post.
NOTE: The top will now be the bottom of the door and
the bottom is now the top.
Insert the new top plug/bushing in the new top of the
door.
Rotate the door 180°.
STEP 2 REVERSING THE DOOR
(ZIFS240 model only) (Cont.)
STEP 2 REVERSING THE DOOR
(ZIFS240 model only) (Cont.)
Re-insert the black screw post in the new bottom of the
door.
Insert the new bottom plug/bushing in the new bottom
of the door. Secure with the screw removed from the
old plug/bushin.
To install the door, set the door onto the left bottom
hinge pin. Holding the door in place, insert the new top
left hinge pin into the door and secure the hinge to the
case with screws.
STEP 3 INSTALL CUSTOM 3/4”
DOOR PANEL AND HANDLE
(ZIFI240 and ZIBI240 models only)
3/4” Overlay Panel Dimensions
Model ZIFI240 and ZIBI240 require
a field-installed overlay door panel.
• The overlay panel must be
secured to a 1/4” thick backer
panel that slides into the trim.
A .10” thick spacer panel must
be placed between the overlay
and backer panel.
A custom handle of your choice,
supplied by your cabinetmaker,
must be installed on this overlay
panel. Countersink all screws into the backer panel.
Screws cannot protrude from the backer panel.
IMPORTANT NOTE: Maximum total weight for custom
door panel is 25 pounds.
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Overlay
Panel
11
Installation Instructions
STEP 3 INSTALL CUSTOM 3/4”
DOOR PANEL AND HANDLE
(ZIFI240 and ZIBI240 models only)
A
B
Custom Panel Hinge Routing Dimensions
Use a 3/4” router bit to cut a notch into the back side of
the assembled panel 3/8” toward the front of the overlay
panel, 3/4” deep and 7/8” wide.
3/4” Overlay Panel Dimensions (in inches)
A (Width) B (Height)
1/4” Backer 23-3/16” 29-9/16”
0.10” Spacer 22-1/2” 29-1/16”
3/4” Overlay 23-5/8” 30”
3/8”
7/8”
3/4”
Back side
of custom
panel
3/4”
7/8”
3/8”
NOTE: Right-hand models
illustrated. Cut notches on the
opposite side for left-hand fresh
food door swing models
ZIFI240 and ZIFS240.
Assemble overlay panels with glue and screws.
Center spacer panel on the backer panel, left to right and
top to bottom. Secure the panels with glue.
Center the spacer/backer panel on the overlay panel.
Secure with glue and screws. Countersink all screws into
the backer panel.
Spacer Panel
Backer Panel
Overlay Panel
Install custom door panel and handle:
• Open door to 90°.
• Remove 5 screws holding trim; lift off trim.
Retain screws.
• A custom handle
of your choice,
supplied by your
cabinetmaker, must
be installed onto
the overlay panel
before the panels
are slid into the
trim. Countersink
all screws into
the backer panel.
Screws cannot protrude from the backer panel.
Handle
Custom
Door Panels
Screws Must
Be Countersunk
Into Panel
NOTE: Right-hand models
illustrated. Follow the
same instructions on the
opposite side for left-
hand fresh food door
swing models ZIFI240 and
ZIFS240.
12
STEP 3 INSTALL CUSTOM 3/4” DOOR
PANEL AND HANDLE
(CONT.)
(ZIFI240 and ZIBI240 models only)
Installation Instructions
• Slide overlay panel into the door trim.
Reinstall the side trim using the trim screws removed
earlier.
STEP 4 LEVEL
• Use an adjustable wrench
to turn the leveling legs and
raise or lower the product.
For built-in installation, adjust
the leveling legs slightly below
the bottom of the countertop.
INSTALLATION TIP:
Measure floor to underside
of countertop inside the
opening. If the room floor
is higher than the opening
floor, adjust the rear
leveling legs approximately
1/8” less than the opening height. Screw front legs all
the way in to shorten the height at the front. This will
allow you to slightly tip the unit into the opening. Once
in the correct position, the front legs can be adjusted to
level the product.
Turn Right to Lower
Turn Left to Raise
Install custom door panel and handle (cont.):
• Place the brushed decorative cover over the side trim
to hide the screw heads. Ensure side trim is aligned top
to bottom and front to back. Snap into place.
NOTE:
For shipping
purposes, the
brushed decorative
cover will be
secured to
the front of
the unit.
STEP 5 CONNECT WATER SUPPLY
(ZIBI240 and ZIBS240 models only)
• Locate and bring the water line tubing to the rear of
the cabinet.
• Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a
bucket, then shut off the water.
Copper Tubing:
• Slip a 1/4” nut and ferrule over both ends of the copper
tubing. Insert the tube into the refrigerator connection
on the unit and tighten the nut.
• Turn on the water to check for leaks.
GE SmartConnect
Tubing:
• Insert the molded end of the tubing into the refrigerator
connection. Tighten the compression nut until it is just
hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
NOTE: Coil excess tubing length behind the unit.
Water line
STEP 7 SLIDE PRODUCT INTO
THE CUTOUT
CAUTION
Do not push against the door panel
with your knees. Do not push or lift the unit by the door
handle. Damage may occur!
ATTENTION
Ne poussez jamais le panneau
de la porte avec vos genoux. Ne poussez jamais votre
appareil ou ne le soulevez jamais par
la poignée de porte. Vous pouvez l’endommager.
Open the door and gently push the unit back into the
opening with your hands against the sides. Be careful
not to entangle power cord.
• In a standard 24” opening, the front face of the
stainless steel door will be flush with adjacent
cabinetry. A custom panel door may protrude 1-3/4”
beyond the surrounding cabinets.
• Check again to be sure the unit is level.
• If the unit is installed under a countertop, adjust the
leveling legs until the unit is resting firmly against the
underside of the countertop.
• If alignment with adjacent cabinetry is an issue, use
a shim to secure the unit against the underside of the
countertop.
STEP 8 SET TEMPERATURE
CONTROLS
• The temperature controls are preset. Refer to the
Owner’s Manual for more information. Allow 12–24
hours for the temperature to stabilize.
NOTE: The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker operate very quietly. You may not notice the unit
running, and when first installed, the fans and motor may
not come on immediately – this is normal. If the display is
lit and the light is working, the unit is operating.
Installation Instructions
13
STEP 6 CONNECT POWER
• Connect power cord plug to a properly grounded
receptacle.
• Check to make sure power is on by opening the door
to see if interior light turns on.
• Bar Refrigerator with Icemaker – The interior fan runs
all the time except during defrost cycle when the door
is open.
• Fresh-Food Refrigerator – The interior fan runs all the
time except when the door is open.
See the Owner’s Manual for further explanation of the fan.
14
Notes
15
Notes
Pub. No. 31-51544-8
Part No. 197D5893P002
01-15 GE
Printed in Slovenia
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram
®
local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
GE
Appliances
Appliance Park
Louisville, KY 40225
GEAppliances.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

GE Monogram ZIBI240HII Guide d'installation

Catégorie
Frigos
Taper
Guide d'installation

dans d''autres langues