1
Wire Connector Mounting Screw
Qty: 3pcs+1 Extra Qty: 1 Extra
A B
modernforms.com Headquarters/Eastern Distribution Center Central Distribution Center Western Distribution Center
Phone (800) 526.2588 44 Harbor Park Drive 1600 Distribution Ct 1750 Archibald Avenue
Fax (800) 526.2585 Port Washington, NY 11050 Lithia Springs, GA 30122 Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Oct. 2019
JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
INSTALLATION INSTRUCTIONS
780-LED Pendant
PD-78013
Back Plate Dimensions
modernforms.com Headquarters/Eastern Distribution Center Central Distribution Center Western Distribution Center
Phone (800) 526.2588 44 Harbor Park Drive 1600 Distribution Ct 1750 Archibald Avenue
Fax (800) 526.2585 Port Washington, NY 11050 Lithia Springs, GA 30122 Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Oct. 2019
INSTALLATION INSTRUCTIONS
780-LED Pendant
PD-78013
Black - Fixtrue-
Red - Fixtrue+
White - Neutral
Black - Hot
Fig.3
Fig.1
Push up
Cable-gripper
Instruction: Adjust the fixture
wire length by pushing the
cable gripper on the canopy
and pulling the wire as desired.
Mounting Plate
Driver
3"L to 3.5"L x 1-1/4"W x 1-1/8"H
C
anopy
Junction Box
Mounting Screw
Junction Box Screw
Wire Connector
A
B
ACRYLIC SHADE WITH CRYSTAL INSERT
RPL-GLA-78013
PREPARATION
1. Shut off the power at the circuit breaker and remove existing
fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a
clear area. Be careful not to lose any small parts necessary
for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back plate from the
fixture.
4. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wire as desired.
a) Retract these wires close to a desirable length to
within the canopy before securing the fixture in
place.
Note: retracting or extending excessive cable
length through the cable gripper is not commended.
b) Warning: Shortening these cables without
professional helps or electronic background is not
advisable.Any modifications to the fixture may
result in voiding the warranty of the product.
5. Secure the mounting back plate to the junction box using
standard junction box screws that comes with the junction box.
Note: (i) using any other non-original-manufacturer provided
junction box screws may result in safety issue; (ii) the side of
the mounting plate marked “GND”must face out.
CONNECTING THE WIRES (Fig. 2)
6.
Connect the driver’s input wires to junction box wires as
shown in Fig. 2, make sure that all wire connectors (A) are
secured. If your outlet box has a green or bare copper ground
wire, connect the fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
Caution: This fixture requires driver’s to be recessed
within the junction box. The hole mounting extensions on
the driver are trimmable/foldable for tighter junction box
fitment.
COMPLETING THE INSTALLATION
7. Secure the fixture to the mounting back plate using the
mounting screw (B).
DIMMING WIRING INFORMATION (Fig. 3)
8. To utilize ELV or TRAIC dimming: use wires black (hot),
white (neutral) and bare copper ground wire (ground).
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
/('3HQGDQW
PD-78013-T24
&$87,217235(9(17(/(&75,&$/6+2&.(1685((/(&75,&,7<+$6%((17851('2))$77+(&,5&8,7%5($.(5
%()25(%(*,11,1*
Ͳ Read all instructions before installing.
Ͳ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
Ͳ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
Ͳ Retain installation instructions for future maintenance reference.
:$51,1*All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
0,6((1*$5'(3RXUpYLWHUWRXWFKRFpOHFWULTXHDVVXUH]YRXVTXHOHGLVMRQFWHXUVRLWPLVKRUVWHQVLRQDYDQWGH
FRPPHQFHU
Ͳ Lisez toutes les instructions avant l’installation.
Ͳ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
Ͳ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
$77(17,21Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
+$5':$5(
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
PD-78013-T24
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
(Fig. 1)
3. Remove the mounting screw (B) and back plate from the
fixture.
4. Adjust the fixture wire length by pushing the cable
gripper on the canopy and pulling the wire as desired.
a) Retract these wires close to a desirable
length to within the canopy before securing
the tixture in place.
retracting or extending excessive cable
length through the cable gripper is not
commended.
b) Shortening these cables without
professional helps or electronic background
is not advisable.Any modifications to the
fixture may result in voiding the warranty of
the product.
5. Secure the mounting back plate to the junction box using
standard junction box screws that comes with the
junction box. the side of the mounting plate marked
“GND”must face out.
(Fig. 2)
6. Connect the driver’s input wires to junction box wires as
shown in Fig. 2, making sure that all wire connectors (A)
are secured. If your outlet box has a green or bare
copper ground wire, connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to
the back plate using the green screw provided. After
wires are connected,tuck them carefully inside the
junction box.
7. Secure the fixture to the mounting back plate using the
mounting screw (B) .
8. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming
wires information.
9. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
10. To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire
(gr ound).
Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Push up
Cable-gripper
Instruction: Adjust the fixture wire
length by pushing the cable
gripper on the canopy and pulling
the wire as desired.
Wire Connector
Junction Box Screw
Mounting Screw
B
A
Junction Box
Canopy
Driver
Mounting Plate
ACRYLIC SHADE WITH
CRYSTAL INSERT
RPL-GLA-78013
Back Plate Dimensions
1 3/8"1 3/4"
∅5 1/2"
White - Neutral
Black - Hot
Purple - Dim+
Red - Fixture+
Black - Fixture-
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Pink or Gray - Dim-
-
1
-
2
-
3
-
4
Modern Forms PD-78013 4 Watt Minx LED Pendant Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Modern Forms WS-93037 Argo Mode d'emploi
-
-
-
-
-
-
-
-
-