TP-LINK tp-link Tapo S500 Smart Wi-Fi Light Switch Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Tapo S500 Smart Wi-Fi Light Switch

Taper: Mode d'emploi

Ce manuel convient également à

Tapo S500 Smart Wi-Fi Light Switch

Wire Your Switch

Disconnect wires from the old switch.

Turn o the circuit breaker. Then

remove the old wallplate of the wall

switch and label the wires.

Connect the wires to the smart switch as

shown below.

Note: No need to distinguish between Line and Load wires.

Ground: Usually green or copper.

Neutral: Usually white, not connected to the dumb switch.

Line/Load: Usually black, and connected to the dumb

switch.

If you are unsure, consult a qualied electrician.

Line up the switch with the mounting

holes. Secure it with screws.

4Attach the wallplate and turn on the

circuit breaker. Then the wiring is nished

Set Up Your Switch

STEP 2 SET UP

Tap the button in the app. Select Switches

and then your model. Follow the step-by-step

app instructions to set up your smart switch.

DOWNLOAD APP

Get the Tapo app from the App Store or

Google Play.

STEP 1

Need some help?

Visit www.tapo.com/support

for technical support, user guides, FAQs,

warranty and more information.

Smart Wi-Fi Light Switch, Single Pole

Quick Start Guide

*Images may dier from your actual product.

Appearance Button Explanations Specications

Safety Notice

Before installing, servicing or removing the switch, read and follow all safety

precautions including the following:

• CAUTION – Risk of Electric Shock – More than one disconnect switch may

be required to de-energize the equipment before servicing. A circuit

breaker which disconnects the Line and Neutral conductor simultaneously

is suitable. Ensure power is o at the circuit breaker before removing or

installing any switch. Use a non-contact voltage tester to ensure the power

is o.

• The Smart Switch must be installed and used in accordance with the

National Electric Code (NEC) or your local electrical code. If you are

unfamiliar with these codes and requirements, or are uncomfortable

performing the installation, consult a qualied electrician.

• Do not install the Smart Switch with wet hands or when standing on wet or

damp surfaces.

• Install only in a suitable UL Listed outlet box (suitable dimensions:

H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).

Rating: 100-120V~ 60Hz

Load: 15A General Use, 600W Incandescent,

120 W Max Fan Ceiling, 1/6 HP Motor.

Operation temperature: 0~40℃

Method of mounting included: Independently mounted

(Vertically position only);

Operating control, Type 1.C action

Pollution Degree 2, Rated Impulse Voltage 2500 V

Software Class A, NEMA Type 1

Restart

Reset

Press and hold for about 5s to reset

Wi-Fi while keeping other settings.

Press to restart your switch.

Press and hold for about 10s to restore

your switch to factory default settings.

On/O

Button

Restart

LED

Reset

Haute tension. Débrancher l'alimentation électrique avant

d'utiliser

High Voltage-Disconnect power supply before servicing

CAUTION

MISE EN GARDE

LED Status

Starting up; disconnected

from cloud.

Solid amber

Blinking amber

Blinking green

White

Solid red

Stay green for 30s

Blinking amber & green

Connecting to Wi-Fi.

Ready for setup.

Device resetting.

Light fixture is off.

Disconnected from Wi-Fi.

Connected to Wi-Fi.

Blinking green slowly Firmware upgrading.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1） This device may not cause harmful interference.

2） This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.

Such modifications could void the user’s authority to operate the equipment.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna

must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas

used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter.”

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre

corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

TP-LINK tp-link Tapo S500 Smart Wi-Fi Light Switch Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Tapo S500 Smart Wi-Fi Light Switch

Taper: Mode d'emploi

Ce manuel convient également à

Tapo S500 Smart Wi-Fi Light Switch

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK tp-link Tapo S500 Smart Wi-Fi Light Switch User guide

TP-LINK tp-link Tapo S500 Smart Wi-Fi Light Switch Mode d'emploi

Ce manuel convient également à

TP-LINK tp-link Tapo S500 Smart Wi-Fi Light Switch Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents