Faber LINE30ST Guide d'installation

Marque: Faber

Modèle: LINE30ST

Catégorie: Cuisinières

Taper: Guide d'installation

INSTALLATION INSTRUCTIONS KIT LINE30ST

INSTRUCTIONS D'INSTALLATION KIT LINE30ST

Refer to Faber U&C Guides for Installation Instructions.

Reportez-vous aux guides Faber U&C pour les instructions d'installation.

Pre-Planning Your Installation - Important: The recommended height to install

this hood off the cooktop is a minimum of 24" electric cooking surfaces and

a maximum of 30” gas surfaces for maximum effectiveness. Also consult the

cooktop manufacturer’s recommendation.

Planiez votre installation - Important : La hauteur recommandée pour installer

cette hotte au-dessus de la surface de cuisson est d’un minimum de 24” surfaces

de cuisson électriques et d’un maximum de 30” surfaces de gaz pour un ma-

ximum d’efcacité. De plus, nous vous recommandons consulter le manuel de

recommandations du fabricant de la surface de cuisson.

Palazzi, Walter

03-Jul-2017

Released

Palazzi, Walter

28-Jun-2017

Released

Version 09/14 - Page 5

The Inca Smart requires 5" round ductwork. To ensure that the blower performs to its

highest possible capacity, ductwork should be as short and straight as possilbe.

Make your ductrun as straight and short as possible. The ductrun should not exceed 25

equivalent feet if ducted with the required minimum of 5" round duct. Count 45º angles

as 3 feet, 90º elbows as 5 feet, and 90º at elbows as 12 feet.

For best results, use no more than three 90° elbows. Make sure that there is a minimum

of 24" of straight duct between elbows if more than one is used. Do not install two

elbows together. If you must elbow right away, do it as far away from the hood's

exhaust opening as possible.

TOOLS NEEDED FOR INSTALLATION

• Saber Saw or Jig Saw

• Drill

• 1 1/4" Wood Drill Bit

• Pliers

• Phillips Screwdriver

• Wire Stripper or Utility Knife

• Metal Snips

• Measuring Tape or Ruler

• Level

• Pencil

• Caulking Gun

• Duct Tape

PLAN YOUR DUCTWORK

The Inca Smart can be used in

standard 30" or 36" wide cabinetry

or with custom hoods 30" wide

and up.

For custom/wood hoods, choose

either YOUR OWN custom liner or

our Standard Liner designed for 30"

and 36" wide installations. Liners

create a perfectly-sealed, non-

combustible nish for the underside

of your custom/wood hood.

The Standard Liners are made

up of two sections: a larger, rear

section (pre-cut out for insertion of

the Inca Smart) and a front section

for a total adjustable depth between

16" and 17 7/8".

!!! IMPORTANT NOTE: DO NOT

REMOVE THE ADDITIONAL

PERFORATED SECTION

AROUND THE PRE-CUT-

OUT WHEN INSTALLING

THE STANDARD LINER WITH

THE INCA SMART MODEL.

THIS PERFORATION IS ONLY

REMOVED FOR USE WITH THE

INCA HC SS MODEL.

Consider the shape, size, and

weight of the Inca Smart and Liner

to determine the configuration

of the custom/wood hood. See

RANGEHOOD DIMENSIONS AND

LINER DIMENSIONS on Page 4.

FOR INSTALLATIONS WITH LINERS

PARTS SUPPLIED FOR INSTALLATION

• 1 Backdraft Damper

• 10 Screws

• Field Wiring Box

• 1 Literature Package

PARTS NEEDED FOR INSTALLATION

• 2 Conduit Connectors

• Power Supply Cable

• Scews for Field Wiring Box

• 1 Wall or Roof Cap

• All Metal Ductwork

OPTIONAL ACCESSORIES AVAILABLE

•Charcoal Filter Kit

For recirculating installations only,

replace charcoal lters as needed

part # FILTER4

•Liners

Create a perfectly-sealed, non-combustible

perimeter around the Inca Smart. Depth adjustable

from 16" - 17

7/8"

Standard Liner 30 Stainless - part # LINE30ST

Standard Liner 36 Stainless - part # LINE36ST

CUSTOM/WOOD

HOOD

STANDARD LINER

INCA SMART

WARNING

When building a custom hood,

always follow all applicable

codes and standards.

1. The custom/wood hood must have a sturdy base (3/4" plywood recommended) to accomodate

the cut-out for the Inca Smart. The base must be recessed to accomodate the height of the

Liner (see LINER DIMENSIONS on Page 4). The Liner attaches to the bottom of the base

using screws appropriate for the size and material of your custom/wood hood. The Inca Smart

inserts into the cut-out in the Liner and base.

2. Position the rear section of the Liner so that it abuts the back edge of your custom/wood

hood. Using a pen, trace the outline of the pre-cut out. Remove the Liner and proceed to MAKE

YOUR CUT-OUTS on Page 6. Install both sections of the Liner and proceed to INSTALL THE

RANGEHOOD on Page 6.

FOR INSTALLATION WITH LINERS

1. The custom/wood hood must have a sturdy base (3/4" plywood recommended)

to accomodate the cut-out for the Hood. The base must be recessed to accomo-

date the height of the Liner. The Liner attaches to the bottom of the base using

screws appropriate for the size and material of your custom/wood hood. The

Hood inserts into the cut-out in the Liner and base.

2.Position the rear section of the Liner so that it abuts the back edge of your

hood. Using a pen, trace the outline of the pre-cut out. Install both sections of the

Liner and proceed to INSTALL THE RANGEHOOD.