3M 2190073 Mode d'emploi

Marque: 3M

Modèle: 2190073

Taper: Mode d'emploi

Ce manuel convient également à

DBI-SALA® Standing Seam Roof Anchor 2190073, 1 EA

FORM NO: 5908312 REV: A

AB C D

12.25 in.

(31.12 cm)

5.25 in.

(13.34 cm)

12 in.

(30.48 cm)

36 in. - 12 in.

(91.44 cm - 30.48 cm)

2190073

USER INSTRUCTION MANUAL

STANDING SEAM ROOF ANCHOR

Anchorage Connector

3 4

5 6

A. B. C. D.

E. F. G.

ABC

15-20 ft-lbs

(20-27 N-m)

22 ga = 160-180 in-lbs (18.1-20.3 N-m)

24 ga = 130-150 in-lbs (14.7-16.9 N-m)

30-35 ft-lbs

(41-47 N-m)

Manufacturer's instructions supplied

with this product at time of shipment

must be followed for proper use, maintenance, and inspection. Alteration or misuse of this product, or

failure to follow instructions, may result in serious injury or death. Make only compatible connections.

This equipment must be installed and used under the supervision of a qualiɥed person. Fall arrest forces

must be limited to 1800 lbs (8 kN). Exercise caution using this equipment near hazardous thermal,

electrical, or chemical sources. / On doit observer les instructions du fabriquant fournies au moment de

l'expédition. Une modiɥcation ou une mauvaise utilisation de ce produit, ou le fait de négliger d'observer

les instructions, peut provoquer une blessure grave voire mortelle. Eɢectuer seulement des connections

compatibles. Cet équipement doit être installé et utilisé sous la supervision d'une personne qualiɥée.

Les forces d'arrêt des chutes doivent être limitées à 1800 lbs (8 kN). Rester prudent lors de l'utilisation

de ce produit a proximité de sources thermiques, électriques ou chimiques dangereuses.

9514258 Rev. A

WARNING / AVERTISSEMENT

9504137 Rev. L

MFRD. (YR, MO) / FABR. (AN, MO): LOT #:

MODEL NO / N° DE MODELE:

Swiveling Standing Seam Roof Anchor

Ancrage de Toit à Joint Debout Pivotant

USE / UTILISATION:

Maximum seam spacing is

36 inches (0.91 m). Minimum decking thickness is 24 gauge

steel. Clamp the two leg assemblies to roof seams with clamps

positioned as shown in diagram. Tighten set screws on all

four clamps to 130-150 in-lbs (15-17 Nm) for 24 gauge steel

and 160-180 in-lbs (18-20 Nm) for 22 gauge or thicker steel.

Connect swivel assembly to leg assemblies using clamp

plates and 1/2 in. (12.7 mm) fasteners. Swivel must be

centered between leg assemblies and must rotate without

contacting clamp plates. Torque fasteners to 30-35 ft-lbs (41-47.5 Nm). See user manual for details. / L'espacement maximum entre joints est

de 36 po (0.91 m). L'épaisseur minimum de tôle est de calibre 24 en acier. Fixer les deux assemblages de jambes au joint du toit avec les

mâchoires positionnées comme montré sur les diagrammes. Serrer les vis sans têtes des quatre mâchoires à 130-150 po-lb (15-17 Nm) pour un

acier d'épaisseur calibre 24 et à 160-180 po-lb (18-20 Nm) pour un acier d'épaisseur calibre 22 ou plus épais. Connecter l'assemblage pivotant à

l'assemblage des jambes en utilisant des plaques de serrage et la visserie de 1/2 in. (12.7 mm). La partie pivotante doit être centrée entre les assemblages

de jambes etdoit pivoter sans rentrer en contact avec les plaques de serrage. Serrer

la visserie à 30-35 ft-lbs (41-47.5 Nm).

Voir le guide d'utilisation pour les détails.

INSPECTION:

Inspect anchor before each use. Do not use if inspection reveals

an unsafe or defective condition. Not user repairable. Re-torque set screws daily to 130-150 in-lbs

(15-17 Nm) for 24 gauge steel and 160-180 in-lbs (18-20 Nm) for 22 gauge or thicker steel. / Inspecter

l'ancrage avant utilisation. Ne pas utiliser si l'inspection révèle une condition défectueuse ou dangereuse.

Non réparable par l'utilisateur. Resserrer les vis sans têtes quotidiennement à 130-150 po-lb (15-17 Nm) pour

un acier d'épaisseur calibre 24 et à 160-180 po-lb (18-20 Nm) pour un acier d'épaisseur calibre 22 ou plus épais.

3M.com/FallProtection

Do not

remove this label.

Ne pas enlever cette étiquette.

9514063

Rev. A

INSPECTION LOG

JOURNAL D'INSPECTION

INITIAL INITIAL

DATE INITIALES DATE INITIALES

SPECIFICATIONS

CARACTERISTIQUES:

Capacity / Capacité:

1 person / personne, 420 lbs (191 kg)

Material / Matériau:

Carbon Steel / Acier carbone

Meets / Rencontre:

OSHA 1910.140 & 1926.502

FORM NO: 5908299 REV: A

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Anchorage Connector.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Anchorage Connector is intended for use as part of a complete personal fall protection system.

Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not described in

the User Instructions, is not approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

! WARNING

This Anchorage Connector is part of a personal fall protection system. It is expected that all users be fully trained in the safe installation and operation

of their personal fall protection system. Misuse of this device could result in serious injury or death. For proper selection, operation, installation,

maintenance, and service, refer to these User Instructions and all manufacturer recommendations, see your supervisor, or contact 3M Technical Service.

• To reduce the risks associated with working with an Anchorage Connector which, if not avoided, could result in serious injury or

death:

- Inspect the device before each use, at least annually, and after any fall event. Inspect in accordance with the User Instructions.

- If inspection reveals an unsafe or defective condition, remove the device from service and repair or replace according to the User Instructions.

- Any device that has been subject to fall arrest or impact force must be immediately removed from service and destroyed.

- The device must only be installed in the speciﬁ ed substrates or on structures detailed in the User Instructions. Installations and use outside the

scope of this instruction must be approved by 3M Fall Protection.

- The substrate or structure to which the anchorage connector is attached must be able to sustain the static loads speciﬁ ed for the anchor in the

orientations permitted in the User Instructions.

- Only connect other fall protection subsystems to the designated anchorage connection point on the device.

- Prior to drilling or fastening, ensure no electric lines, gas lines, or other critical embedded systems will be contacted by the drill or the device.

- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet the

requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements. Always

consult a Competent or Qualiﬁ ed Person before using these systems.

- (ROOF ANCHORS) Never attach a horizontal lifeline between two or more roof anchors unless speciﬁ cally provided for in the User Instructions.

- (ROOF ANCHORS) Only attach device to roof sheathing that is appropriately secured to a structural member that can sustain the static loads

required by this device.

- (ROOF ANCHORS) Only use fasteners speciﬁ ed for use with this device. Other fastener types must be approved by 3M.

- (STANDING SEAM ANCHORS) Always ensure the roof seam is compatible with the device seam clamps.

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with your

doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or suitability

of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections. Consult

3M prior to using this equipment in combination with components or subsystems other than those described in the User Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures, chemical

hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or your fall protection equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an unintended

fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.



Prior to installation and use of this equipment, record the product identiﬁ cation information from the ID label in the

Inspection and Maintenance Log (Table 2) at the back of this manual.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA™ Standing Seam Roof Anchor. The Standing Seam Roof Anchor is a single point

anchorage connector for mounting Leading Edge Self-Retracting Lifelines (SRL-LE) on sloped or ﬂ at standing seam roofs on seam

spacing of up to 36 inches. The Standing Seam Roof Anchor can only be used with Smart Lock or Ultra-Lok Leading Edge Self-

Retracting Lifelines.

Figure 2 illustrates components of the Standing Seam Roof Anchor. See Table 1 for Component Speciﬁ cations. The

Standing Seam Roof Anchor is comprised of a Swivel Bracket (B) mounted on a center Load Bar (A) with Adjustable Legs (C)

that slide to the width of the roof seam and attach with roof Seam Clamps (D). The Adjustable Legs slide along the Load Bar on

Mounting Brackets (E) that can be secured at the desired width. The SRL-LE is secured in the Swivel Bracket by Locking Pins (F)

inserted through the Model Speciﬁ c Alignment Holes (H) in the Swivel Bracket and SRL-LE Casing.

Table 1 – Speciﬁ cations

System Speciﬁ cations:

Capacity: 1 Person with a combined weight (clothing, tools, etc.) of no more than 420 lbs (191 kg)

Anchorage: Fall Arrest: The structure to which the Anchorage Connector is attached must sustain static loads

applied in the directions permitted by the Fall Arrest System of at least: 3,600 lbs (16 kN) with

certiﬁ cation of a Qualiﬁ ed Person

; or 5,000 lbs (22 kN) without certiﬁ cation. When more than one

Personal Fall Arrest System (PFAS) is attached to an anchorage, these static loads must be multiplied by

the number of PFAS attached to the anchorage.



OSHA 1926.500 and OSHA 1910.66: Anchorages used for attachment to a Personal Fall Arrest

System (PFAS) must be independent of any anchorage used to suspend or support platforms and must

support 5,000 lbs (22 kN) per user attached, or be designed, installed, and used as part of a complete

PFAS which maintains a Safety Factor of at least 2 and is supervised by a Qualiﬁ ed Person

Restraint: The structure to which the Anchorage Connector is attached must sustain static loads applied

in the directions permitted by the Restraint System of at least 3,000 lbs (13 kN). When more than one

Restraint System is attached to an anchorage, the static load must be multiplied by the number of

Restraint Systems attached to the anchorage.

Seam Requirements: The Standing Seam Roof Anchor must be attached to the seam as shown in

Figure 8. The hook side of the Seam Clamp must hook under the roof seam for proper attachment.

Roof Panels: The Standing Seam Roof Anchor must only be used on structural standing seam roof

panels that meet the geometric and load requirements speciﬁ ed in Table 1. Roof panels must be a

minimum of 24 gauge steel.

Multiple Anchor Installations: See Figure 7 and Section 3.1 for guidelines on installing multiple

Standing Seam Roof Anchors onto one roof. Two or more Standing Seam Roof Anchors must not apply

loads to a single panel fastener.

Dimensions: See Figure 1 for the dimensions of each Standing Seam Roof Anchor model.

Weight: 28 lbs without SRL

Component Speciﬁ cations:

Figure 2

Reference Component Materials Note:

A Load Bar Steel Tube

B Swivel Bracket Steel Weldement

C Adjustable Legs Steel Angle

D Seam Clamp and Set Screws

Clamps - Aluminum

Set Screw - Stainless

Steel

Torque Set Screws to 160-180 in-lbs

(18.1-20.3 N-m) for 22 guage steel or

thicker; 130-150 in-lbs (14.7-16.9 N-m)

for 24 guage steel.

E Mounting Brackets Steel

F Locking Pins Steel

G Adjustable Leg Bolts Steel

Torque Adjustable Leg fasteners to 30-35

ft-lbs (41-47 N-m)

H SRL Model Speciﬁ c Alignment Holes

1 Capacity:

This product has been tested to a 420 lbs (191 kg) Maximum Capacity per OSHA.

2 Qualiﬁ ed Person: An individual with a recognized degree or professional certiﬁ cate, and extensive experience in Fall Protection. This individual must be

capable of design, analysis, evaluation, and speciﬁ cation in Fall Protection.

Table 1 – Speciﬁ cations

Compatible Roof Panels:

A&S Double-Lok, 22 ga steel Firestone UC3, 24 ga steel

A&S Double-Lok, 24 ga steel Firestone UC4, 24 ga steel

A&S Ultra Dek, 22 ga steel Firestone UC6, 24 ga steel

A&S Ultra Dek, 24 ga steel MBCI Lok Seam, 22 ga steel

AB Martin Roofing AB Seam 19.5, 24 ga steel MBCI Lok Seam, 24 ga steel

AEP Span Design Span hp, 22 ga steel MBCI UltraDek, 22 ga steel

AEP Span High Seam, 24 ga steel MBCI UltraDek, 24 ga steel

AEP Span Snap Seam, 22 ga steel McElroy Metals Master-Lok 90 ML90, 22 ga steel

AEP Span Snap Seam, 24 ga steel McElroy Metals Master-Lok 90, ML90 24 ga steel

American Buildings Company Standing Seam II Panel, 24 ga

steel

McElroy Metals Medallion-Lok, 22 ga steel

Architectural Building Components Perma seam, 22 ga steel McElroy Metals Medallion-Lok, 24 ga steel

Architectural Building Components Perma seam, 24 ga steel Merchant & Evans #305, 24 ga steel

Bax Steel Buildings Bax-Lock, 22 ga steel Mesco Ultra Dek, 22 ga steel

Bax Steel Buildings Bax-Lock, 24 ga steel Mesco Ultra Dek, 24 ga steel

BC Steel Buildings BCL 24-SD, 22 ga steel Metal Sales Vertical Seam, 22 ga steel

BC Steel Buildings BCL 24-SD, 24 ga steel Metal Sales Vertical Seam, 24 ga steel

Berridge Cee-Lock, 24 ga steel NCI/Midwest Metallic Ultra Dek, 22 ga steel

Butler MR24, 24 ga steel NCI/Midwest Metallic Ultra Dek, 24 ga steel

Ceco CXP, 22 ga steel New Tech Machinery S5 5500 Snap Lock 1 1/2, 24 ga steel

Ceco CXP, 24 ga steel New Tech Machinery SS675 Sanp Lock 1 3/4, 24 ga steel

Central States Manufacturing Central Loc, 22 ga steel Petersen Aluminum Corp Snap Clad, 22 ga steel

Central States Manufacturing Central Loc, 22 ga steel Petersen Aluminum Corp Snap Clad, 24 ga steel

Central Texas Metal Roofing Supply ShurLoc 175, 22 ga steel Star Building Systems Starshield, 22 ga steel

Central Texas Metal Roofing Supply ShurLoc 175, 24 ga steel Star Building Systems Starshield, 24 ga steel

Centria SDP175, 22 ga steel Taylor Metal Easy Lock Standing Seam, 24 ga steel

Centria SDP175, 24 ga steel U.S. Metals US-175LS, 22 ga steel

Copper Sales UC3, 24 ga steel U.S. Metals US-175LS, 24 ga steel

Copper Sales UC4, 24 ga steel Una-Clad UC3, 24 ga steel

Copper Sales UC6, 24 ga steel Una-Clad UC4, 24 ga steel

Custom Bilt Metals SL-175,0 24 ga steel Una-Clad UC6, 24 ga steel

Dimensional Metals DL-15, 24 ga steel United Structures of America Guardian I, 22 ga steel

Dimensional Metals IL-20, 22 ga steel United Structures of America Guardian I, 24 ga steel

Dimensional Metal IL-20, 24 ga steel United Structures of America Guardian II, 22 ga steel

Englert Series 2000, 22 ga steel United Structures of America Guardian II, 24 ga steel

Englert Series 2000, 24 ga steel Varco Pruden SSR, 24 ga steel

Fabral 3” Snap Rib, 24 ga steel Whirlwind Building Systems Super Seam II, 22 ga steel

Fabral Slim Seam, 24 ga steel Whirlwind Building Systems Super Seam II, 24 ga steel

Fabral Thin Seam, 24 ga steel

1.0 PRODUCT APPLICATION

1.1 PURPOSE: Anchorage Connectors are designed to provide anchorage connection points for Fall Arrest

or Fall Restraint

systems: Restraint, Work Positioning, Personnel Riding, Rescue, etc.



Fall Protection Only: This Anchorage Connector is for connection of Fall Protection Equipment. Do not connect

Lifting Equipment to this Anchorage Connector.

1.2 STANDARDS: Your Anchorage Connector conforms to the national or regional standard(s) identiﬁ ed on the front cover

of these instructions. If this product is resold outside the original country of destination, the re-seller must provide these

instructions in the language of the country in which the product will be used.

1.3 SUPERVISION: Use of this equipment must be supervised by a Competent Person

1.4 TRAINING: This equipment must be installed and used by persons trained in its correct application. This manual is to

be used as part of an employee training program as required by ANSI and OSHA. It is the responsibility of the users and

installers of this equipment to ensure they are familiar with these instructions, trained in the correct care and use of this

equipment, and are aware of the operating characteristics, application limitations, and consequences of improper use of

this equipment.

1.5 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and

the means at hand to implement and communicate that plan to users, authorized persons

, and rescuers

. A trained, on-

site rescue team is recommended. Team members should be provided with the equipment and techniques to perform a

successful rescue. Training should be provided on a periodic basis to ensure rescuer proﬁ ciency.

1.6 INSPECTION FREQUENCY:

The Anchorage Connector shall be inspected by the user before each use and, additionally,

by a competent person other than the user at intervals of no longer than one year.

Inspection procedures are described in

the “Inspection and Maintenance Log”. Results of each Competent Person inspection should be recorded on copies of the

“Inspection and Maintenance Log”.

1.7 AFTER A FALL: If the Anchorage Connector is subjected to the forces of arresting a fall, it must be removed from service

immediately, clearly marked “DO NOT USE”, and then destroyed.

2.0 SYSTEM REQUIREMENTS

2.1 ANCHORAGE: Anchorage structure requirements vary with the fall protection application. Structure on which the

Anchorage Connector is placed or mounted must meet the Anchorage Strength speciﬁ cations deﬁ ned in Table 1.

2.2 PERSONAL FALL ARREST SYSTEM: Figure 1 illustrates the application of this Anchorage Connector. Personal Fall Arrest

Systems (PFAS) used with the system must meet applicable Fall Protection standards, codes, and requirements. The PFAS

must incorporate a Full Body Harness and limit Arresting Force to the following values:

Maximum Arresting Force Free Fall

PFAS with Shock Absorbing Lanyard 1,800 lb (8 kN)

Refer to the instruction(s) included with your

Lanyard or SRD for Free Fall limitations.

PFAS with Self Retracting Device (SRD) 1,800 lb (8 kN)

2.3 FALL PATH AND SRD LOCKING SPEED: A clear path is required to assure positive locking of an SRD. Situations which

do not allow for an unobstructed fall path should be avoided. Working in confined or cramped spaces may not allow the

body to reach sufficient speed to cause the SRD to lock if a fall occurs. Working on slowly shifting material, such as sand

or grain, may not allow enough speed buildup to cause the SRD to lock.

2.4 HAZARDS: Use of this equipment in areas with environmental hazards may require additional precautions to prevent

injury to the user or damage to the equipment. Hazards may include, but are not limited to: heat, chemicals, corrosive

environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or overhead materials

that may fall and contact the user or Personal Fall Arrest System.

2.5 FALL CLEARANCE: Figure 3 illustrates the components of a Fall Arrest. There must be sufﬁ cient Fall Clearance (FC)

to arrest a fall before the user strikes the ground or other obstruction. Clearance is affected by a number of factors

including: Anchorage Location, (A) Lanyard Length, (B) Lanyard Deceleration Distance or SRD Maximum Arrest Distance,

subsystem for speciﬁ cs regarding Fall Clearance calculation.

1 Fall Arrest System: A collection of Fall Protection Equipment conﬁ gured to arrest a free fall.

2 Fall Restraint System: A collection of Fall Protection Equipment conﬁ gured to prevent the person’s center of gravity from reaching a fall hazard.

3 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary,

hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

4 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.

5 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

6 Inspection Frequency: Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the frequency of competent person

inspections.

2.6 SWING FALLS: Swing Falls occur when the anchorage point is not directly above the point where a fall occurs (see Figure

4). The force of striking an object in a swing fall may cause serious injury or death. Minimize swing falls by working as directly

below the anchorage point as possible. Do not permit a swing fall if injury could occur. Swing falls will signiﬁ cantly increase the

clearance required when a Self-Retracting Device or other variable length connecting subsystem is used.

2.7 COMPONENT COMPATIBILITY: 3M equipment is designed for use with 3M approved components and subsystems

only. Substitutions or replacements made with non-approved components or subsystems may jeopardize compatibility of

equipment and may affect the safety and reliability of the complete system.

2.8 CONNECTOR COMPATIBILITY: Connectors are considered to be compatible with connecting elements when they

have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to

inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors

must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.

Non-compatible connectors may unintentionally disengage (see Figure 5). Connectors must be compatible in size, shape,

and strength. If the connecting element to which a snap hook or carabiner attaches is undersized or irregular in shape, a

situation could occur where the connecting element applies a force to the gate of the snap hook or carabiner (A). This force

may cause the gate to open (B), allowing the snap hook or carabiner to disengage from the connecting point (C).

Self-locking snap hooks and carabiners are required by ANSI Z359 and OSHA.

2.9 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all

connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all

connectors are fully closed and locked.

3M connectors (snap hooks and carabiners) are designed to be used only as speciﬁ ed in each product’s user’s instructions.

See Figure 6 for examples of inappropriate connections. Do not connect snap hooks and carabiners:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard

size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the

snap hook complies is equipped with a 3,600 lb (16 kN) gate. Check the marking on your snap hook to verify that it

is appropriate for your application.

C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the anchor, and

without visual conﬁ rmation seems to be fully engaged to the anchor point.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the lanyard and

connector speciﬁ cally allows such a connection).

F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that

roll-out could occur.

G. In a manner that does not allow the connector to align properly while under load.

3.0 INSTALLATION



Installation of the DBI-SALA Standing Seam Roof Anchor must be supervised by a Qualiﬁ ed Person

. The installation

must be certiﬁ ed by a Competent Person

as meeting the criteria for a Certiﬁ ed Anchorage, or that it is capable of

supporting the potential forces that could be encountered during a fall.

3.1 PLANNING: Table 1 includes a list of Compatible Roof Panels. Plan the fall protection system prior to installation of the

Standing Seam Roof Anchor. Account for all factors that may affect safety before, during and after a fall. Consider all

requirements, limitations and speciﬁ cations deﬁ ned in Section 2 and Table 1.

Anchor Placement: Figure 7 illustrates proper placement of the Standing Seam Roof Anchor(s) on the standing seam

roof. Roof anchors must be located and spaced properly on the roof to preserve structural strengths of the roof and roof

anchor. Requirements are as follows:

• A panel Section (A) is comprised of all Roof Panels within the rectangular boundaries (X and Y) of four adjacent Panel

Fasteners (B). No two Roof Anchors should apply loads to the same Panel Fastener.

• Roof Anchors must be positioned at least two Panel Section Widths (2X) and two Panel Section Lengths (2Y) from any

Roof Edge (C).

• There must be a minimum of four Panel Section Widths (4X) between the Seam Clamps on adjacent Roof Anchors.

• There must be a minimum of four Panel Section Lengths (4Y) between the Swivel Brackets of adjacent Roof Anchors.

3.2 INSTALLING THE STANDING SEAM ROOF ANCHOR: The Standing Seam Roof Anchor can be installed on metal roof

seams meeting the anchorage requirements speciﬁ ed in Table 1. The maximum allowable roof seam ﬂ ange width is 36

inches (91.4 cm). Multiple Standing Seam Roof Anchors can be installed on the same roof but they must be positioned

on the roof per the requirements deﬁ ned in the previous section (and Figure 7). Figure 8 illustrates installation of the

Standing Seam Roof Anchor. To install the Standing Seam Roof Anchor:

1. Torque the fasteners securing the Seam Clamps on the Adjustable Legs to 15-20 ft-lbs (20-27 N-m).

2. Loosen the Adjustable Leg fasteners and slide the Adjustable Legs along the Load Bar so the Seam Clamps will align

on the desired roof seams with the Swivel Bracket centered between the two seams.

3. Position the Seam Clamps on the roof seams. Seam Clamps should be aligned with the Seam Clamp Set Screws

opposite the folded overlaps on the standing seams. Torque the Set Screw on each Seam Clamp to the torque value

recommended for the roof gauge (see Table 1).

4. Center the Swivel Bracket and Load Bar between the Seam Clamps and tighten the Adjustable Leg fasteners to

secure the Load Bar to the Adjustable Legs. Torque the Adjustable Leg fasteners to 30-35 ft-lbs (41-47 N-m).



Inspection: After installation, inspect the Standing Seam Roof Anchor per the “Competent Person” inspection

checkpoints in the “Inspection and Maintenance Log” (Table 2).

3.3 INSTALLING THE SRL-LE: Figure 9 illustrates mounting of Smart Lock Leading Edge Self-Retracting Lifelines (A) or

Ultra-Lok Leading Edge Self-Retracting Lifelines (B) in the Standing Seam Roof Anchor. To install the SRL-LE in the Swivel

Bracket of the Standing Seam Roof Anchor:

1. Position the SRL-LE in the Swivel Bracket with the Swivel Eye on the SRL-LE aligned with the appropriate mounting

holes in the back end of the Swivel Bracket. Insert the provided Mounting Pin through the Swivel Bracket and Swivel

Eye and secure with the Cotter Pin.

2. Rotate the free end of the SRL-LE up or down until the through-hole in the SRL-LE Housing aligns with mounting

holes in the front end of the Swivel Bracket. Insert the provided Mounting Pin through the Swivel Bracket and SRL-LE

Housing and secure with the Cotter Pin.

4.0 USE

4.1 BEFORE EACH USE: Verify that the work area and Personal Fall Arrest System (PFAS) meet all criteria deﬁ ned in Section

2 and a formal rescue plan is in place. Inspect the Standing Seam Roof Anchor per the ‘User’ inspection points deﬁ ned

on the “Inspection and Maintenance Log” (Table 2). If inspection reveals an unsafe or defective condition, do not use the

system. Remove the system from service and contact 3M regarding replacement.

4.2 FALL ARREST CONNECTIONS: The Standing Seam Roof Anchor is used with a full body harness and Leading Edge

Self-Retracting Lifeline (SRL-LE). Connect the SRL-LE Lifeline to the back dorsal D-ring on the harness as instructed in the

instructions included with the SRL-LE.

5.0 INSPECTION

5.1 INSPECTION FREQUENCY: The Standing Seam Roof Anchor must be inspected at the intervals deﬁ ned in Section 1.

Inspection procedures are described in the “Inspection and Maintenance Log” (Table 2). Inspect all other components of

the Fall Protection System per the frequencies and procedures deﬁ ned in the manufacturer’s instructions.

1 Qualiﬁ ed Person: An individual with a recognized degree or professional certiﬁ cate, and extensive experience in Fall Protection. This individual must be capable

of design, analysis, evaluation, and speciﬁ cation in Fall Protection.

2 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazard-

ous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.



Standing Seam Roof Anchors are equipped with a Radio Frequency Identiﬁ cation (RFID) Tag. The RFID Tag can be

used in conjunction with a Handheld Reading Device to simplify inspection and inventory control and provide records for

your fall protection equipment.

5.2 DEFECTS: If inspection reveals an unsafe or defective condition, remove the Standing Seam Roof Anchor from service

immediately and contact 3M regarding replacement. Do not attempt to repair the Fall Arrest System.

5.3 PRODUCT LIFE: The functional life of the Fall Arrest System is determined by work conditions and maintenance. As long

as the product passes inspection criteria, it may remain in service.

6.0 MAINTENANCE, SERVICING, STORAGE

6.1 CLEANING: Periodically clean the Standing Seam Roof Anchor metal components with a soft brush, warm water, and a

mild soap solution. Ensure parts are thoroughly rinsed with clean water.

6.2 SERVICE: If inspection reveals an unsafe or defective condition, remove the Standing Seam Roof Anchor from service

immediately and contact 3M regarding replacement. Do not attempt to repair the Fall Arrest System.

6.3 STORAGE AND TRANSPORT: When not in use, store and transport the Standing Seam Roof Anchor and associated fall

protection equipment in a cool, dry, clean environment out of direct sunlight. Avoid areas where chemical vapors may

exist. Thoroughly inspect components after extended storage.

7.0 LABELS

Figure 10 Illustrates labels on the Standing Seam Roof Anchor. Labels must be replaced if they are not fully legible.

Table 2 – Inspection and Maintenance Log

Inspection Date: Inspected By:

Components: Inspection: (See Section 1 for Inspection Frequency) User

Competent

Person

Standing Seam Roof

Anchor (Figure 2)

Inspect the Standing Seam Roof Anchor for damage: Look for cracks, dents, corrosion or

deformities. Look for bending or wear on the Load Bar (A), Adjustable Legs (C), Swivel

Bracket (B), Locking Pins (F), and Seam Clamps (D).

Conﬁ rm all hardware: Seam Clamp bolts and nuts, Set Screws, and Adjustable Leg bolts

and nuts are present and in safe working order.

Conﬁ rm the Swivel Bracket, SRL-LE, and Pins can be inserted through the holes in the

Swivel Bracket and lock in place.

Conﬁ rm that the Swivel Bracket freely swivels 360 degrees.

Re-torque the Mounting Bracket and Seam Clamp fasteners to the torque requirements

listed in Table 1.

Labels (Figure 10)

Verify that all labels are securely attached and are legible (see ‘Labels’)

PFAS and Other

Equipment

Additional Personal Fall Arrest System (PFAS) equipment (harness, SRL, etc) that are

used with the Anchorage System should be installed and inspected per the manufacturer’s

instructions.

Serial Number(s): Date Purchased:

Model Number: Date of First Use: