LG GL-B402RPHR Le manuel du propriétaire

Catégorie
Réfrigérateurs-congélateurs
Taper
Le manuel du propriétaire

Ce manuel convient également à

P/NO : MFL68489001
ENGLISH
FRENCH
ARABIC
3
10
11
13
22
23
25
25
27
Lamp Replacement
Green Ion Door Cooling /
Ice Beam Door Cooling (Optional)
Inverter On feature (Optional)
WARNING
Keep ventilation openings, in the appliance enclosure or in
the built-in-structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by the
manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage
compartment, unless they are recommended by the
manufacturer.
The refrigerant and insulation blowing gas used in the
appliance requires special disposal procedures. When
disposal, please consult with services agent or a similarly
qualified person.
This appliance contains a small amount of isobutane refrigerant
(R600a), natural gas with high environmental compatibility, but it is
also combustible. When transporting and installing the appliance,
care should be taken to ensure that no parts of the refrigerating
circuit are damaged. Refrigerant squirting out of the pipes could
ignite or cause an eye injury. If a leak is detected, avoid any naked
flames or potential sources of ignition and air the room in which the
appliance is standing for several minutes.
Never startup an appliance showing any signs of damage. If in
doubt, consult your dealer.
If gas used is R600a
Do not use or store
inflammable materials like
ether, benzene, alcohol,
medicine, LP gas, spray or
cosmetics
near or in the
refrigerator.
It may cause
explosion or fire.
Inverter-On feature (Optional)
Minimum requirement: UPS/ Inverter
should be in ON condition having
minimum 600VA capacity along with
minimum 120Ah capacity battery
connected with the refrigerator’s
power supply socket.
Green Ion Door
Cooling / Ice
Beam Door
Cooling (Optional)
When the Freezer compartment is not enough cold in winter, adjust the control for the freezer to High
(4/5/ / )
For achieving temperature in Freezing , Energy and Storage Test, Freezer control may be required to set at
or ●●
●●
‘3’ or ‘4’
GREEN ION DOOR COOLING / ICE BEAM DOOR
COOLING (OPTIONAL)
Use this function when calling the Customer Call Centre and receive precise diagnosis when the
Refrigerator malfunctions or fails. Use it only when advised by the consultant and not otherwise.
SMART DIAGNOSIS (Only for Selected External Micom Models)
1. Open all the doors of the refrigerator.
2. Press the refrigerator control (REF
TEMP) button for 3 sec or more.
3. If the buzzer sounds 4 times (Frequency
of SDS Buzzer is 2000Hz, 0.2sec Off/
0.2sec On 4 times) place the phone near
the speaker hole in the top right hand
side door hinge.
4. Ensure the microphone of the
telephone is towards the speaker hole.
CAUTION
The transmission sound may be irritating.
Do not take away the telephone until the sound
stops for good diagnosis.
Smart diagnosis function is...
Use this function when calling the Customer Call Centre and receive precise diagnosis when the
Refrigerator malfunctions or fails. Use it only when advised by the consultant and not otherwise.
How to use the function
Be aware!
Difference of the regional call qualities may have influence on the function.
If you use home phone, better communication performance will enable much better service.
Smart diagnosis data transmission may not be successful if the call is made from a mobile phone
with poor network reception.
First, call LG service center. Only use the Smart Diagnosis feature when instructed to do so by the LG
call center agent.
5. Do not take away the telephone while
data is being transmitted.
6. During the data transmission for smart
diagnosis, hold the telephone 10cm
away from the speaker hole and avoid
any background noises. After inputting
SDS, SDS buzzer will ring. After
completion of the data transmission,
the consultant will explain the result of
the smart diagnosis and advice
a c c o r d i n g l y. W h e n t h e d a t a
transmission is completed, the
refrigerator will be automatically turned
off and on a few seconds later.
SMART DIAGNOSIS (Only for Selected Internal Micom Models)
LED PATTEN DURING INVERTER-ON MODE (OPTIONAL)
During the use of this feature, you will find this pattern of LED running. It is a symbol
that the product is running at basic energy requirement. One can press the button “REF
TEMP” to change the LED setting during power cuts, if needed. The LED will then show
the setting as desired. When the mode is changed from Normal supply to Inverter mode
& vice versa, the LED pattern will take some time to display the change.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

LG GL-B402RPHR Le manuel du propriétaire

Catégorie
Réfrigérateurs-congélateurs
Taper
Le manuel du propriétaire
Ce manuel convient également à