VTech CS5209 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
Ce manuel convient également à
User’s manual
Go to www.vtechphones.com
to register your product for
enhanced warranty support
and latest VTech product
news.
1
2
3
5
6
4
12
13
11
10
9
8
7
14
15
Telephones identified with this
logo have reduced noise and
interference when used with most
T-coil equipped hearing aids and
cochlear implants. The TIA-1083
Compliant Logo is a trademark of
the Telecommunications Industry
Association. Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Congratulations
on purchasing your new VTech product. Before
using this telephone, please read
Important safety instructions.
This manual has instructions on how to set up and
register your new handset. For instructions on
using the handset, see the Quick start guide that
came with your telephone base.
You may also view or download the online user’s
manual for a full set of installation and operation
instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1939
User’s manual
1
The battery is low and needs charging.
The battery is charging.
The battery is fully charged.
Handset ringer is off.
New voicemail received from your telephone service provider.
NEW
There are new caller ID log entries.
ANS ON Answering system is on.
MSG#
5/10 Number of new/old messages recorded.
ECO The ECO mode activates automatically to reduce power consumption when the
handset is within range of the telephone base.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
THIS SIDE UP
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
CS5229 base Do not place
the handset in
the charger.
Add and register a handset
You can add new CS5209 handsets
(purchased separately) to your CS5229/
CS5229-2/CS5229-3/CS5229-4/ CS5229-5/
CS5249/CS5249-2/CS5249-3/CS5249-4/
CS5249-5 telephone system. Your telephone
system supports a maximum of 5 handsets.
Each handset must be registered with
the telephone base before use. When
first purchased, each expansion handset
displays To register HS... and ... see manual
alternately.
• Charge the new handset without interruption for
at least 30 minutes before registering it to the
telephone base.
To register a handset to a CS5229 telephone
base:
• Place the new handset in the CS5229
telephone base.
After about 10 seconds, the handset displays
Registering.... When the registration process
completes, the handset displays Registered
and you hear a beep. The registration
process takes about 90 seconds.
To register a handset to a CS5249 telephone base:
1. Press and hold FIND HANDSET on the
CS5249 telephone base for about four
seconds until the IN USE light turns on and it
shows Registering....
2. Press Quiet on the new handset. The new
handset shows Registering....
After about 10 seconds, the handset displays
Registering.... When the registration process
completes, the handset displays Registered and
you hear a beep. The registration process takes
about 90 seconds.
Deregister handsets
If you want to replace a handset or reassign the
designated handset number of a registered
handset, you must deregister all the handsets and
then individually register each handset.
If you want to register a handset to another
telephone base, you must deregister all handsets,
and then register each handset individually to the
desired telephone base.
To deregister all handsets from the telephone base:
1. Press and hold FIND HS/ FIND HANDSET
on the telephone base for about 10 seconds
until the IN USE light on the telephone base
turns on and starts flashing.
CS5229 base
CS5249 base
2. Immediately press FIND HS/
FIND HANDSET again. You must press
FIND HS/ FIND HANDSET while
the IN USE light is still flashing. The
IN USE light turns off, and you hear a
confirmation tone.
3. All handsets display To register HS...
and ...see manual alternately when
the deregistration process completes.
The deregistration process takes
about 10 seconds.
Operating range
This cordless telephone operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even
so, this handset and telephone base can
communicate over only a certain distance
- which can vary with the locations of the
telephone base and handset, the weather,
and the layout of your home or office.
When the handset is out of range, the handset
displays Out of range OR Base no power.
If there is a call while the handset is out of
range, it may not ring, or if it does ring, the
call may not connect well when you press
. Move closer to the telephone base, and
then press to answer the call. If the
handset moves out of range during a
telephone conversation, there may be
interference. To improve reception, move
closer to the telephone base.
This power conserving technology reduces power
consumption for optimal battery performance. The
ECO mode activates automatically whenever the
handset is synchronized with the telephone base.
ECO mode
Taking care of your telephone
Your cordless telephone contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original
packing materials to protect your telephone if you
ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do
not use the handset outdoors in the rain, or handle
it with wet hands. Do not install the telephone base
near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges
harmful to electronic equipment. For your own
safety, take caution when using electrical appliances
during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
General product care
CS5209
DECT 6.0 accessory handset
for use with VTech models
CS5229/CS5229-2/CS5229-3/CS5229-4/CS5229-5
CS5249/CS5249-2/CS5249-3/CS5249-4/CS5249-5
Connect the charger
Charge the battery
12 hrs
1 – Charging pole
1 – Handset earpiece
2 – LCD display
3 – MENU/SELECT
• Show the menu.
• While in a menu, press to select an item,
or save an entry or setting.
4 – /
• Review the phonebook when the phone
is not in use.
• Increase the listening volume during a
call.
• Scroll up while in a menu, phonebook,
caller ID log, or redial list.
• Move the cursor to the right when entering
numbers or names.
/
• Review the caller ID log when the phone
is not in use.
• Decrease the listening volume during a
call.
• Scroll down while in a menu, phonebook,
caller ID log, or redial list.
• Move the cursor to the left when entering
numbers or names.
5 – OFF/CANCEL
• Hang up a call.
• Silence the ringer temporarily while the
handset is ringing.
• Press and hold to erase the missed call
indicator while the phone is not in use.
• Press to return to the previous menu; or
press and hold to return to idle mode,
without making changes.
6 – QUIET
• Press and hold to set and turn on the quiet
mode, or turn it off.
• Press repeatedly to show other dialing
options when reviewing a caller ID log
entry.
7 – INT
• Press to start an intercom conversation or
transfer a call (for multi-handset models
only).
8 – MUTE/DELETE
• Mute the microphone during a call.
• Delete digits or characters while using the
dialing keys.
• Silence the ringer temporarily while the
handset is ringing.
9 – CHARGE light
• On when the handset is charging.
10 – REDIAL/PAUSE
• Press repeatedly to review the redial list.
• Press and hold to insert a dialing pause
while entering a number.
11 –
• Make or answer a call.
• Answer an incoming call when you hear a
call waiting alert.
12 –
• Press repeatedly to add or remove 1 in
front of the caller ID log entry before
dialing or saving it to the phonebook.
• Press and hold to set or dial your
voicemail number.
13 – TONE
• While you have set the dial mode to
pulse and on a call, press to switch to tone
dialing temporarily.
14 –
• Make or answer a call using the handset
speakerphone.
• During a call, press to switch between the
speakerphone and the handset earpiece.
15 – Microphone
Your telephone package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
The ENERGY STAR® program (www.
energystar.gov) recognizes and
encourages the use of products
that save energy and help protect
our environment. We are proud to
mark this product with the ENERGY
STAR® label indicating it meets the
latest energy efficiency guidelines.
Battery
indicators
Battery status Action
The screen
is blank, or
shows Put in
charger and
flashes.
The battery
has no charge
or very little
charge. The
handset cannot
be used.
Charge without
interruption
(at least 30
minutes).
The screen
shows Low
battery and
flashes.
The battery has
enough charge
to be used for a
short time.
Charge without
interruption
(at least 30
minutes).
The screen
shows
HANDSET X.
The battery is
charged. To keep
the battery
charged, place
it in the charger
when not in
use.
S
m
For operations and guides to help you using
your telephone, and for latest information and
supports, go and check the online help topics
and online FAQs.
Use your smartphone or mobile device to access
our online help.
• Go to https://help.vtechphones.com/cs5209;
OR
• Scan the QR code on the right. Launch the
camera app or QR code scanner app on
your smartphone or tablet. Hold the device’s
camera up to the QR code and frame it. Tap
the notification to trigger the redirection of
the online help.
- If the QR code is not clearly displayed,
adjust your camera’s focus by moving
your device closer or further away until it
is clear.
You can also call our Customer Support at
1 (800) 595-9511 [in US] or 1 (800) 267-7377
[in Canada] for help.
What’s in the box Handset overview
Display icons overview
Install the battery
Connect and charge battery Before use Need help?
Charger overview
LCD language setting
If you accidentally set the LCD language to Spanish or French, press MENU and then
enter 364# to change the handset LCD language back to English while the handset is
not in use.
IMportant safety
instructions
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on
the product.
3. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
4. Do not use this product near water such as near
a bath tub, wash bowl, kitchen sink, laundry tub
or a swimming pool, nor in a wet basement or
shower.
5. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
6. Avoid placing the telephone system in places
with extreme temperature, direct sunlight, or
other electrical devices. Protect your phone
from moisture, dust, corrosive liquids and
fumes.
7. Slots and openings in the back or bottom of the
telephone base and handset are provided for
ventilation. To protect them from overheating,
these openings must not be blocked by placing
the product on a soft surface such as a bed, sofa
or rug. This product should never be placed
near or over a radiator or heat register. This
product should not be placed in any area where
proper ventilation is not provided.
8. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home or office, consult your
dealer or local power company.
9. Do not allow anything to rest on the power
cord. Do not install this product where the cord
may be walked on.
10. Never push objects of any kind into this product
through the slots in the telephone base or
handset because they may touch dangerous
voltage points or create a short circuit. Never
spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the telephone base or handset other
than specified access doors may expose you
to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
12. Do not overload wall outlets and extension
cords.
13. Unplug this product from the wall outlet and
refer servicing to an authorized service facility
under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or
water.
• If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operation instructions. Improper adjustment
of other controls may result in damage
and often requires extensive work by an
authorized technician to restore the product
to normal operation.
• If the product has been dropped and the
telephone base and/or handset has been
damaged.
• If the product exhibits a distinct change in
performance.
14. Avoid using a telephone (other than cordless)
during an electrical storm. There is a remote risk
of electric shock from lightning.
15. Do not use the telephone to report a gas
leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when
the adapter is plugged into the power
outlet, or when the handset is replaced in its
cradle. This is a common event associated
with the closing of any electrical circuit. The
user should not plug the phone into a power
outlet, and should not put a charged handset
into the cradle, if the phone is located in an
environment containing concentrations of
flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in such an
environment could create a fire or explosion.
Such environments might include: medical
use of oxygen without adequate ventilation;
industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
16. Only put the handset of your telephone next to
your ear when it is in normal talk mode.
17. The power adapter is intended to be correctly
oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug
in place if it is plugged into a ceiling, under-the-
table or cabinet outlet.
18. For pluggable equipment, the socket-outlet
shall be installed near the equipment and shall
be easily accessible.
19. CAUTION: Use only the batteries
indicated in this manual. There may be a risk of
explosion if a wrong type of battery is used
for the handset. Use only the supplied
rechargeable batteries or replacement
batteries (BT162342/BT262342) for the handset.
Do not dispose of batteries in a fire. They may
explode.
20. Use only the adapter included with this
product. Incorrect adapter polarity or voltage
can seriously damage the product.
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use Only Supplied Battery.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
• Charge the battery provided with this product
only in accordance with the instructions and
limitations specified in this manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless telephones and implanted cardiac
pacemakers. Supported by the U.S. Food and
Drug Administration, WTR recommends to
physicians that:
Pacemaker patients
• Should keep wireless telephones at least six
inches from the pacemaker.
• Should NOT place wireless telephones directly
over the pacemaker, such as in a breast pocket,
when it is turned ON.
• Should use the wireless telephone at the ear
opposite the pacemaker.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless telephones.
Specifications are subject to change without notice.
© 2020 for VTech Communications, Inc.
All rights reserved. 06/20. CS5209_CIB_V3.0
Document order number: 91-011960-030-100
11. Afin de réduire les risques d’électrocution,
ne démontez pas l’appareil, mais apportez-le
plutôt à un centre de service qualifié s’il doit
être réparé. En enlevant le couvercle, vous vous
exposez à des tensions dangereuses ou autres
dangers similaires. Un remontage inadéquat
peut être à l’origine d’une électrocution
lors d’une utilisation ultérieure de l’appareil.
Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.
12. Ne surchargez pas les prises de courant et les
rallonges.
13. Débranchez cet appareil de la prise de courant
et communiquez avec le département de
service à la clientèle de VTech dans les cas
suivants :
• Lorsque le cordon d’alimentation est
endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source
d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement
en respectant les instructions de
fonctionnement. Réglez uniquement les
commandes indiquées dans le les instructions
de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer
un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé
afin de rétablir le fonctionnement normal de
l’appareil.
• Si le produit a été échappé et que le socle et/
ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de
sa performance.
14. Évitez d’utiliser un téléphone (autre qu’un sans
fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
15. N’utilisez pas le téléphone pour rapporter une
fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être
provoquée lorsque l’adaptateur est branché à
une prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un événement
commun associé à la fermeture d’un circuit
électrique. L’utilisateur ne devrait pas brancher
le téléphone à une prise de courant, et ne
devrait pas déposer le combiné chargé sur
le socle, si le téléphone se trouve à proximité
d’un endroit comportant des concentrations
de gaz inflammables, à moins que la ventilation
soit adéquate. Une flammèche dans un tel
endroit pourrait provoquer un incendie ou une
explosion. De tels environnements peuvent
comprendre: des endroits où l’on utilise de
l’oxygène médical sans ventilation adéquate;
des gaz industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
16. Ne placez que le combiné de votre téléphone
près de votre oreille lorsqu’en mode de
conversation.
17. Ces adaptateurs ont été conçus pour être
orientés en position verticale ou montés au sol.
Les broches ne sont pas conçues pour maintenir
l’adaptateur en place si celui-ci est barnché
dans une prise au plafond ou sous une table/
armoire.
18. Pour le MATERIEL RACCORDE PAR PRISE DE
COURANT, le socle de prise de courant doit
etre installe a proximite du materiel et doit etre
aisement accessible.
19. MISE EN GARDE: Il peut y avoir un
risque d’explosion si vous utilisez le mauvais
type de piles pour le téléphone. N’utilisez que
les piles rechargeable inclus ou les piles de
rechange (BT162342/BT262342). N’incinérez pas
les piles. Celles-ci risqueraient d’exploser.
20. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et
mettre votre sécurité en péril.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent.
• Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux rebus
auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est corrosif et
pourrait causer des brûlures ou des blessures
aux yeux ou à la peau. L’électrolyte est toxique
si avalé.
• Soyez prudents lorsque vous manipulez les piles
afin d’éviter les courts-circuits provoqués par
des matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil,
selon les instructions et limites spécifiées dans
ce guide d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique uniquement
aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une
distance d’au moins six pouces du stimulateur
cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel
que dans une poche de chemise, lorsque celui-
ci est en marche.
• Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a
pas identifié de risque pour les détenteurs de
simulateurs cardiaques causés par les gens qui
utilisent un téléphone sans fil à proximité de ceux-
ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui
constituent des avantages pour les téléphones sans
fil affichent également des restrictions. Les appels
téléphoniques sont transmis entre le combiné sans
fil et le socle par le biais d’ondes radio ; il y a donc
la possibilité que vos conversations téléphoniques
sans fil soient interceptées par des équipements
de réception radio se trouvant dans la portée du
combiné sans fil. Pour cette raison, vous ne devez
pas percevoir les communications téléphoniques
sans fil comme étant aussi confidentielles que
celles des téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone
sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être
contrôlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si
le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téléviseurs :
Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interférences aux
téléviseurs et aux magnétoscopes. Pour réduire
ou prévenir de telles interférences, ne placez
pas le socle du téléphone sans fil près ou sur un
téléviseur ou magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner le téléphone
sans fil du téléviseur ou du magnétoscope afin de
réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles avec soin
afin de ne pas les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le conducteur peut
surchauffer et causer des blessures. Respectez la
polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure
métallique de nickel : Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez
pas et ne les percez pas. Tel que les autres piles
de ce type, elles pourraient dégager une matière
toxique qui peut causer des blessures corporelles
si elles sont brûlées ou percées.
The RBRC® seal
The RBRC® seal on the nickel-metal
hydride battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program to
collect and recycle these batteries at
the end of their useful lives, when
taken out of service within the United States and
Canada.
The RBRC® program provides a convenient
alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which
may be illegal in your area.
VTech’s participation in RBRC® makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH
battery recycling and disposal bans/restrictions
in your area. VTech’s involvement in this program
is part of its commitment to protecting our
environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered
trademarks of Rechargeable Battery Recycling
Corporation.
FCC, ACTA and IC
regulations
FCC Part 15
NOTE: This equipment has been tested and
found to comply with the requirements for a
Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These
requirements are intended to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation. Privacy of
communications may not be ensured when using
this telephone.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product.
This product has been tested and found to comply
with the FCC criteria. The handset may be safely
held against the ear of the user. The telephone
base shall be installed and used such that parts
of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8
inches) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC
rules and with technical requirements adopted
by the Administrative Council for Terminal
Attachments (ACTA). The label on the back or
bottom of this equipment contains, among
other things, a product identifier in the format
US:AAAEQ##TXXXX. This identifier must be
provided to your telephone service provider upon
request.
The plug and jack used to connect this equipment
to premises wiring and the telephone network
must comply with applicable Part 68 rules and
technical requirements adopted by ACTA. A
compliant telephone cord and modular plug is
provided with this product. It is designed to be
connected to a compatible modular jack that is also
compliant. An RJ11 jack should normally be used
This telephone is set up to comply with the energy-
conserving standards right out of the box. These
instructions are intended for California Energy
Commission (CEC) compliance testing only. When the
CEC battery charging testing mode is activated, all
telephone functions, except battery charging, will be
disabled.
To activate the CEC battery charging testing
mode:
1. Unplug the telephone base power adapter
from the power outlet. Make sure all handsets
are plugged with charged batteries before
proceeding.
2. While you press and hold /FIND HS, plug
the telephone base power adapter back to the
power outlet.
3. After about 10 seconds, when the IN USE
light starts flashing, release /FIND HS and
immediately press it again within two seconds.
When the phone successfully enters the CEC
battery charging testing mode, all handsets display
To register HS... and ...see manual alternately.
When the phone fails to enter this mode, repeat
steps 1 to 3 above.
To deactivate the CEC battery charging testing
mode:
1. Unplug the telephone base power adapter from
the power outlet, and then plug it back in. Then
the telephone base is powered up as normal.
2. Press and hold /FIND HS on the telephone
base for about four seconds until the
IN USE light turns on.
3. Press # QUIET on the handset and it shows
Registering.... The handset shows Registered
and you hear a beep when the registration
process completes. This process takes about 60
seconds.
California Energy
Commission battery charging
testing instructions What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories
provided in the sales package (“Product”) are free
from defects in material and workmanship, pursuant
to the following terms and conditions, when
installed and used normally and in accordance with
the Product operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America
and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during the
limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair or
replace at VTech’s option, without charge, a Materially
Defective Product. If we repair the Product, we may
use new or refurbished replacement parts. If we
choose to replace the Product, we may replace it with
a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or
equipment. Repair or replacement of the Product, at
VTech’s option, is your exclusive remedy. VTech will
return the repaired or replacement Products to you
in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product
under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the
date the repaired or replacement Product is shipped
to you or (b) the time remaining on the original one-
year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or
other liquid intrusion.
2. Product that has been subjected to contact
with liquid, water, rain, extreme humidity or
heavy perspiration, sand, dirt or the like; but
then only to the extent the damage was not
caused by incorrectly securing the waterproof
Limited Warranty handset’s protective elements, for example,
failing to properly close a seal), or such
protective elements are damaged or missing
(e.g. a cracked battery door), or subjecting
a Product to conditions beyond its stated
specifications or limits (e.g. 30 minutes in 1
meter of fresh water).
3. Product that has been damaged due to repair,
alteration or modification by anyone other
than an authorized service representative of
VTech;
4. Product to the extent that the problem
experienced is caused by signal conditions,
network reliability, or cable or antenna
systems;
5. Product to the extent that the problem is
caused by use with non-VTech accessories;
6. Product whose warranty/quality stickers,
product serial number plates or electronic
serial numbers have been removed, altered or
rendered illegible;
7. Product purchased, used, serviced, or
shipped for repair from outside the United
States of America or Canada, or used
for commercial or institutional purposes
(including but not limited to Products used for
rental purposes);
8. Product returned without a valid proof of
purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of
America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to
www.vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery
or handling charges incurred in the transport
of the Product(s) to the service location. VTech
will return repaired or replaced Product under
this limited warranty. Transportation, delivery or
handling charges are prepaid. VTech assumes no
risk for damage or loss of the Product in transit. If
the Product failure is not covered by this limited
warranty, or proof of purchase does not meet the
terms of this limited warranty, VTech will notify you
and will request that you authorize the cost of repair
prior to any further repair activity. You must pay
for the cost of repair and return shipping costs for
the repair of Products that are not covered by this
limited warranty.
What must you return with the Product to get
warranty service?
1. Return the entire original package and
contents including the Product to the VTech
service location along with a description of the
malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales
receipt) identifying the Product purchased
(Product model) and the date of purchase or
receipt; and
3. Provide your name, complete and correct
mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to
this Product. VTech provides no other warranties for
this Product. The warranty exclusively describes all
of VTech’s responsibilities regarding the Product.
There are no other express warranties. No one is
authorized to make modifications to this limited
warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other
rights, which vary from state to state or province to
province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for
ordinary use) are limited to one year from the date
of purchase. Some states/provinces do not allow
limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue,
inability to use the Product or other associated
equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this
Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales receipt as proof of
purchase
Frequency
control Crystal controlled PLL synthesizer
Transmit
frequency Handset: 1921.536-1928.448 MHz
Channels DECT channel: 5
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirement Handset: 2.4V Ni-MH battery
Charger: 6V DC @ 400mA
Memory Phonebook: 50 memory locations;
up to 30 digits and 15 characters
Caller ID log: 30 memory locations;
up to 24 digits and 15 characters
Call block: 150 entries
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez
votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale
avant de le nettoyer. N’utilisez pas de
nettoyeurs liquides ni en aérosol. N’utilisez
qu’un chiffon doux et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau, tel que
près d’un bain, d’un lavabo, d’un évier de
cuisine, d’un bac de lavage ou d’une piscine, ou
dans un sous-sol humide ou sous la douche.
5. Ne déposez pas ce téléphone sur un chariot,
support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
6. Évitez d’installer le système téléphonique dans
les endroits soumis à une température extrême,
à la lumière directe du soleil ou à proximité
immédiate d’autres appareils électriques ou
électroniques. Protégez votre téléphone contre
les sources d’humidité, la poussière, les vapeurs
et les liquides corrosifs.
7. Le boîtier de l’appareil est doté de fentes et
d’ouvertures d’aération situées à l’arrière ou en
dessous. Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être obstruées en
plaçant l’appareil sur un lit, divan, tapis ou autre
surface similaires. Ne placez pas cet appareil à
proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas
dans une unité murale ou un cabinet fermé qui
ne possède pas d’aération adéquate.
8. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage
de votre maison, consultez votre marchand ou
votre fournisseur d’électricité.
9. Ne déposez rien sur le cordon d’alimentation.
Installez cet appareil dans un endroit sécuritaire,
là où personne ne pourra trébucher sur la
ligne d’alimentation ni le cordon téléphonique
modulaire.
10. N’insérez jamais d’objets à travers les fentes et
ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou
court-circuiter des pièces, ce qui constituerait
un risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans l’appareil.
For C-UL compliance
only
for connecting to a single line and an RJ14 jack for
two lines. See the installation instructions in the
user’s manual.
The Ringer Equivalence Number (REN) is used to
determine how many devices you may connect to
your telephone line and still have them ring when
you are called. The REN for this product is encoded
as the 6th and 7th characters following the US: in
the product identifier (e.g., if ## is 03, the REN is
0.3). In most, but not all areas, the sum of all RENs
should be five (5.0) or less. For more information,
please contact your telephone service provider.
This equipment must not be used with Party
Lines. If you have specially wired alarm dialing
equipment connected to your telephone
line, ensure the connection of this equipment
does not disable your alarm equipment. If you
have questions about what will disable alarm
equipment, consult your telephone service
provider or a qualified installer.
If this equipment is malfunctioning, it must be
unplugged from the modular jack until the
problem has been corrected. Repairs to this
telephone equipment can only be made by the
manufacturer or its authorized agents. For repair
procedures, follow the instructions outlined under
the Limited warranty.
If this equipment is causing harm to the telephone
network, the telephone service provider may
temporarily discontinue your telephone service.
The telephone service provider is required to
notify you before interrupting service. If advance
notice is not practical, you will be notified as soon
as possible. You will be given the opportunity to
correct the problem and the telephone service
provider is required to inform you of your right
to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities,
equipment, operation, or procedures that could
affect the proper functioning of this product. The
telephone service provider is required to notify
you if such changes are planned.
If this product is equipped with a corded or
cordless handset, it is hearing aid compatible.
If this product has memory dialing locations,
you may choose to store emergency telephone
numbers (e.g., police, fire, medical) in these
locations. If you do store or test emergency
numbers, please:
Remain on the line and briefly explain the reason
for the call before hanging up.
Perform such activities in off-peak hours, such as
early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
Privacy of communications may not be ensured
when using this telephone.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this
terminal equipment is 1.0. The REN indicates
the maximum number of devices allowed to
be connected to a telephone interface. The
termination of an interface may consist of any
combination of devices subject only to the
requirement that the sum of the RENs of all the
devices not exceed five.
This product meets the applicable Innovation,
Science and Economic Development Canada
technical specifications.
VTech Communications, Inc. and its suppliers
assume no responsibility for any damage or loss
resulting from the use of this user’s manual. VTech
Communications, Inc. and its suppliers assume no
responsibility for any loss or claims by third parties
that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste
555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or
1 (800) 267-7377 in Canada
• Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the
telephone base and the cordless handset by
radio waves, so there is a possibility that the
cordless telephone conversations could be
intercepted by radio receiving equipment
within range of the cordless handset. For
this reason, you should not think of cordless
telephone conversations as being as private as
those on corded telephones.
• Electrical power: The telephone base of this
cordless telephone must be connected to a
working electrical outlet. The electrical outlet
should not be controlled by a wall switch. Calls
cannot be made from the cordless handset if
the telephone base is unplugged, switched off
or if the electrical power is interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference, do
not place the telephone base of the cordless
telephone near or on top of a TV or VCR.
If interference is experienced, moving the
cordless telephone farther away from the
TV or VCR often reduces or eliminates the
interference.
• Rechargeable batteries: Exercise care in
handling batteries in order not to create a short
circuit with conducting material such as rings,
bracelets and keys. The battery or conductor
may overheat and cause harm. Observe proper
polarity between the battery and the battery
charger.
• Nickel-metal hydride rechargeable batteries:
Dispose of these batteries in a safe manner. Do
not burn or puncture the battery. Like other
batteries of this type, if burned or punctured,
they could release caustic material which could
cause injury.
About cordless
telephones
Disclaimer and
Limitation of Liability Technical specifications
-
1
-
2
VTech CS5209 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: VTech CS5209 User manual