Verkada BR32 Guide d'installation
- Catégorie
- Détecteur de fumée
- Taper
- Guide d'installation
Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.0 (20210929)
(V1.0 first published 20210929)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2
Introduction
What’s in the box
What you’ll need
●BH61 Wireless Alarm Hub
●A working internet connection
●Smartphone or laptop
●#2 Phillips driver (screwdriver or power
drill)
●¼ inch (6.35mm) drill bit if using wall
anchors
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Connect
Please note: Add your BH61 Wireless Alarm Hub
to Command before setting up your Wireless
Motion Sensor.
●To register your product, please
proceed to: verkada.com/start
1x BR32 Wireless
Motion Sensor
2x CR123A batteries
4x Screws
3
4x Wall anchors
Introduction
Sensor overview
LED Behavior
After installing the batteries, the motion sensor will
go into walk test mode for ten minutes. While in test
mode, the green LED will:
●turn on when motion is detected.
●turn off after five seconds pass with no
detected motion.
After ten minutes in test mode, the device will
return to normal operation.
While in normal operation, the green LED will:
●NOT turn on when motion is detected.
●flash rapidly three times every two minutes
to indicate low battery.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
LED
4
Installation
Mounting 1/3
Please note: Ensure your Wireless Alarm Hub is configured in Command before setting up
your wireless motion sensor.
Detach the mount bracket from
the device.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
The recommended position for
the motion sensor should be 6
feet (1.8 meters) from the floor in
the corner of a room. The sensor
will detect motion at a range of
35 feet (10 meters) at a 90
degree horizontal field of view.
Installation
Mounting 2/3
Drill holes if using wall anchors.
Mount the bracket on a flat surface or in a corner
with the supplied screws and wall anchors.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
6
Appendix
BR32 Compliance
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
8
FCC
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance may void the user’s authority to operate his equipment. (Example – use only
shielded interface cables when connecting to computer or peripheral devices)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
IC
Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la
conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou
émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
9
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Verkada BR32 Guide d'installation
- Catégorie
- Détecteur de fumée
- Taper
- Guide d'installation
dans d''autres langues
- English: Verkada BR32 Installation guide
Documents connexes
-
Verkada BH61 Guide d'installation
-
-
-
Verkada AD33 Guide d'installation
-
-
-
-
-
-