Quick Installation Guide
Fanvil Technology Co., Ltd
www.fanvil.com
V63
V0 2
P/N:CJBA100527B0
Screen icon
In hands-free mode
In headset mode
In handset mode Do not disturb activated
(Red)
Mute activated
Silent mode
Packaging list
DSS Keys, It can be set as line
key/function key/speed dial key, etc.
Message waiting indicator
Left and right navigation keys
Up navigation key, Shortcut to call log
Down navigation key, Shortcut to Status
OK key
Keys features
IP Phone Handset
Handset Cord
Stand Power Adapter
(Optional)
Ethernet Cable Quick Installation Guide
- 2 -
Wall Stand
(Buy separately)
In idle mode or during ringing: increase or
decrease ringer volume
In communication: increase or decrease
handset, headset or hands-free volume
Call is on hold
New SMS
New VM messages
Voice quality level
of call
Keypad locked
Forward call(s)
Missed call(s)
Received call(s)
Internet connected
Internet is disconnected
Dialed call(s)
No IP address
Wireless network connected
Wireless network disconnected
X
!
Wireless network failure
Auto-answering
activated
Bluetooth device
paired connection
Call forward activated
Disable do not disturb
(Beige)
VPN activated
VLAN activated
SIP hotspot activated
Soft keys
Home key, go back to Homepage
Return key, go back to the
previous directory
Phonebook key
Voice message key
Headset key, activate/deactivate headset
In idle mode:
activate/deactivate silent mode
In communication mode:
mute/un-mute a call
Redial key, access to redial the last record
Hand-free key, activate/
deactivate hands free
- 3 -
Network connect
Using Ethernet
1. The power on the device and connect the WAN port of the
phone to the RJ45 socket of a hub/switch or a router (LAN side
of the router) using the Ethernet cable.
2. The default is DHCP mode.
Making a call
Accepting a call
1. Pre-dialing: enter the phone number and pick up the handset.
Language setting
1. Press Menu key > Basic > Language.
2. Select the desired language and press OK soft key.
2. Direct dialing: lift the handset and enter the phone number.
3. Handsfree: enter phone number and press or vice versa.
4. Headset: enter phone number and press or vice versa.
5. Designated line: press line key, enter phone number and press
dial key.
1. Using the handset: pick up the handset.
2. Using the headset: press .
3. Using the handsfree: press .
Configuration
Configuration via LCD menu of phone
1. Press Menu > Advanced (default password 123).
2. Select Network: To configure the Network Settings
(IPv4/IPv6/IPv4&IPv6, DHCP/Static/PPPoE).
3. Select Accounts: To configure enable the account, fill the SIP
server address, port, user name, password etc.
4. Save the configuration.
Configuration via web
1. Get the IP address from the phone: Press down navigation
key, or Menu > Status > IPv4 / IPv6.
2. Login: Input the IP address in the web browser. The PC and
phone should be in the same IP address segment (The default
username and password are both ‘admin’.)
3. Configure: Select network/account etc, and fill the relevant
content.
4. Save the configuration.
Installation the device
Please follow the instructions in below picture to install the
device.
Bracket desktop installation
Wall mounting (wall stand need buy separately)
Connecting to the device
Please connect power adapter, network, PC, handset, and
headset to the corresponding ports as described in below
picture.
① USB port: connect USB device (USB flash drive).
② Power port: connect the power adapter.
③ Network port: connecting local area network or Internet.
④ PC port: the network port connect to the computer.
⑤ Headset port: connect headset.
⑥ Handset port: connect IP Phone handset.
Internet PC Headset Handset
USB
5V
⑥⑤④ ③
①
②
PUSH
40°
45°
Fanvil Technology Co., Ltd
Website: www.fanvil.com
Tel: +86-755-2640-2199 Fax: +86-755-2640-2618
Add: 10/F Block A, Dualshine Global Science Innovation Center,
Honglang North 2nd Road, Bao'an District, Shenzhen, China
Putting a call on hold
Call transfer
Attended transfer:
Blind transfer:
1. Press Xfer soft key during the active conversation, the call
is put on hold.
2. Dial the second telephone number.
3. When the call is answered, then press Xfer soft key to
complete the operation.
1. Press Xfer soft key during the active conversation, the call
will be on hold.
2. Then enter the 2nd telephone number and press Xfer soft
key.
1. Press Hold soft key, caller is put on hold.
2. To retrieve the call press Resume soft key.
Note: with more than one active call, select desired call
with the navigator key and use the corresponding soft key
to hold or resume.
Call forward
1. Press Menu > Features > Call Forward.
2. Select the line, the type of forward, enter the destination
number and status, and press OK soft key.
Call conference
1. Once in line with 1st caller, press Conf soft key, 1st caller
is put on hold.
2. Then call the 2nd number.
3. After, 2nd call is established, press Conf soft key to set up
the conference.
Programmable key
1. You can configure shortcuts for the programmable keys.
2. Press Menu > Basic > Keyboard, select among the
configurable items, and select your desired type and value,
press OK key.
Do not disturb
1. Press DND soft key, and enable the device do not disturb
mode.
2. Or press Menu > Features > DND, and select the Mode
and Type, and press OK key.
Call Mute
1. Press to Mute the microphone during the call.
2. Press again to un-mute the conversation.
Redial
1. Press key, redial a call number.
Phonebook
Access Phonebook:
Add new entry:
1. Press Contact soft key, Press All Contacts or other group
> Press Add.
2. Enter name and number and press OK soft key.
1. Press or Contact soft key or Menu > PhoneBook >
Local Contacts.
2. Select All Contacts or other group.
3. To dial an entry, press Dial soft key or pickup handset or
press or .
Voice mail
1. To access your voice mailbox, press or Menu > Message
> Voice Message, number of messages will be indicated if
provided by your server or pbx.
2. Select the line and press Play to call.
Bluetooth
1. Plug a Bluetooth dongle into the USB port.
2. Press Menu > Basic > Bluetooth.
3. Press OK soft key to enter the bluetooth open interface.
After opening, press Scan soft key to display the list of
bluetooth scanned. Select any device and press connect.
WiFi
1. Plug a Wi-Fi dongle into the USB port.
2. Press Menu > Basic > WLAN.
3. Press OK soft key to enter the WLAN open interface. After
opening, press Scan soft key to display the list of Wi-Fi
scanned.
4. Press Enter soft key to enter the available Network, select
the wireless network, press the Connect soft key and enter
the password to connect.
Call list
1. Press up navigator key or Menu > CallLog > Local Call Logs.
2. Scroll through the list using navigator key.
3. To dial an entry, press Dial soft key or pickup handset or
press or .
Regulatory Compliance
Federal Communication Commission (FCC) — USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received; including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a product identifier in the format US: 3I1IPNANV63.
If requested, this number must be provided to the telephone company.
Industry Canada Equipment Standard for Digital Equip-ment (ICES) — Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development (ISED) — Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de
rayonnement et votre corps
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou
transmetteur.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d’Innovation, Sciences et Développement
économique Canada.
-
1
-
2
-
3
-
4
-
5
-
6
dans d''autres langues
- English: Fanvil V63 Installation guide
Documents connexes
Autres documents
-
Wildix V65 Manuel utilisateur
-
Ubiquiti UNVR Manuel utilisateur
-
Ubiquiti WAVEAPR Manuel utilisateur
-
Linon Largo Single Door Cabinet White Ant Assembly Instructions
-
RCA 25210 Manuel utilisateur
-
EnGenius DURAFON 1X Le manuel du propriétaire
-
Alcatel-Lucent Alcatel-Lucent AH80 Bluetooth Headset Mode d'emploi
-
VTech IS9141-5 2 Line Corded and Cordless Telephone Mode d'emploi
-
Snom US Manuel utilisateur
-