8. The Certified Solution must not be taken into, or used in, any hazardous locations not

listed in these Operating Instructions, including, but not limited to, locations that are

classified as Class I, Division 1, or outside North America, including global locations

classified as Zone 0, 1, 20, or 21.

9. Failure to follow these Operating Instructions invalidates the Device as a Certified Solution

for use in Hazardous Locations.

FCC COMPLIANCE STATEMENT:

This Certified Solution complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this Device may not cause harmful interference, and (2) this

radio frequency energy and, if not used in accordance with these Operating Instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this Certified Solution does cause

harmful interference to radio or television reception, which can be determined by turning the

Certified Solution off and on, the user is encouraged to try to correct the interference by

increasing the separation between the Certified Solution and the television or radio.

FCC RF EXPOSURE COMPLIANCE:

This Certified Solution complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This Certified Solution should be operated with minimum distance of 20cm

between the radiator and your body.

Solution.

Cette solution certifiée contient un ou des émetteurs/récepteurs exempts de licence

conformes aux RSS exempts de licence d'Innovation, Sciences et Développement

économique Canada. Le fonctionnement de la Solution certifiée est soumis aux deux

conditions suivantes : (1) Cette Solution certifiée ne doit pas provoquer d'interférences ; et (2)

Cette Solution Certifiée doit accepter toute interférence, y compris les interférences

susceptibles d'entraîner un fonctionnement indésirable de la Solution Certifiée.

IC RF EXPOSURE COMPLIANCE:

This Certified Solution complies with RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This Certified Solution should be operated with a minimum

shipped with this product and available at https://bit.ly/34ucz1B. Please refer all customer

service and warranty questions to your local Equipment Mobility Manager. For more details,

please follow the link https://bit.ly/3qT8n2W or call USA 1-877-776-2829.

4. The Certified Solution comes with threaded inserts (M4x0.7 and 3.7mm deep), to tailor

your Certified Solution to work with a variety of AMPS compatible mounts, including:

• Vehicle mounts, tabletop/desk mounts, equipment mounts, and more.

• For more information see the OtterBox AMPS compatibility sheet.

5. Periodic cleaning will improve performance and operational life of the Certified Solution.

• Use warm water and light soap to remove dirt, mud, or debris from the exterior.

• Lightly blow or tap out any water trapped in the Certified Solution’s audio ports

• Available in two types for different work applications: standard and insulated.

Adjust cuff to ensure snug fitStandard Glove Insulated Glove

• If preferred, wipe dry with so cloth or terry cloth towel. Avoid materials that

can mar seals or screen protector.

HARDLINE SERIES QUICK START GUIDE

GUIDE DE DÉMARRAGE RAPIDE DE LA SÉRIE HARDLINE

PRODUCT SAFETY & GENERAL INFORMATION:

CAUTION: Before using this mobile device (“Device”), read this entire pamphlet which contains

important operating instructions.

1. This equipment is suitable for use in Class I and Class II, Division 2, and Class III Divisions 1

process and, together, constitute a complete mobile solution (“Certified Solution”) that meets

the following standards for use in the stated hazardous locations (“Hazardous Locations”):

1. UL 121201 Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III,

Divisions 1 and 2 Hazardous (Classified) Locations.

2. UL 60950-1 & CAN/CSA C22.2 No. 60950-1-07, (Information Technology Equipment - Safety -

Part 1: General Requirements).

3. CSA C22.2 No. 213-17 Nonincendive Electrical Equipment for Use in Class I and II, Division 2

and Class III, Divisions 1 and 2 Hazardous (Classified) Locations.

PRODUCT SAFETY & GENERAL INFORMATION, CONTINUED:

1. REMOVING THE CASE FROM THE DEVICE AT ANY TIME WILL INVALIDATE THE CERTIFICATION TO

2. NEVER USE CHARGING EQUIPMENT INSIDE A HAZARDOUS LOCATION. The Certified Solution

must be charged outside of Hazardous Locations, preferably in a climate-controlled office

or equipment depot environment. No process or equipment, including the OtterBox

Hardline Series Charging Station, should be used in a Hazardous Location.

3. STRUCTURAL DAMAGE TO THE CASE OR DEVICE WILL INVALIDATE THE CERTIFICATION TO USE

THE DEVICE IN HAZARDOUS LOCATIONS. If the Device and/or case incurs any physical or

structural damage, or if the Device becomes otherwise inoperable, it is no longer a

Certified Solution for use in Hazardous Locations and must be removed from service.

Contact your local Equipment Mobility Manager for re-installation and re-certification prior

to further use in Hazardous Locations. Upon inspection, the OtterBox authorized integration

(single or four bay.)

• Slide the Certified Solution onto the charger, by placing the alignment notch on

the center post and wait a few seconds for the LED to glow red. If incorrectly

aligned, it blinks to alert you.

other Qi wireless chargers.

Folded 6 panel insert Final Size 6.67” x 3.96”