Show Home ZW37 Manuel utilisateur

Marque
Show Home
Modèle
ZW37
Taper
Manuel utilisateur
FCC/IC
smart plug (2channel)
ZW37 Smart Plug(2channel) Manual
Show Home Products warrants this product to be free from manufacturing defects for
a period of two years from the original date of consumer purchase. This warranty is limited
to the repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this product.
This warranty is in lieu of all other warranties, expressed or implied. Some states do not
allow limitations on how long an implied warranty lasts or permit the exclusion or limitation
of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from
state to state. if the unit should prove defective within the warranty period.
Model:ZW37
Power: 120 VAC, 60 Hz.
Signal (Frequency): 908.42 MHZ.
Maximum load for outlet 10A, 1200W Resistive
Maximum load for the Z-Wave controlled outlet:
600W Incandescent, ½ HP Motor or 1200W Resistive
Range: Up to 100 feet line of sight between the Wireless Controller
and the closest Z-Wave receiver module.
Operating Temperature Range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice
due to continuing product improvement
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-Wave
DEVICES TO CONTROL APPLIANCES. OPERATION
OF THE Z-Wave DEVICE MAY BE IN A DIFFERENT
ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN
UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG
BUTTON ON THE REMOTE IS PRESSED. Z-Wave DEVICES
MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED
EVENT PROGRAMMING. DEPENDING UPON THE APPLI-
ANCE, THESE UNATTENDED OR UNINTENTIONAL OP-
ERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS
CONDITION. FOR THESE REASONS, WE RECOMMEND
DO NOT RETURN THIS PRODUCT TO THE STORE
THE FOLLOWING:
DO NOT USE Z-Wave DEVICES TO CONTROL ELECTRIC
HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRES-
ENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR
UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
WARNING
WARRANTY
SPECIFICATIONS
Website:www.ishowlights.com
IMPORTANT!
The fixture controlled by the Z-Wave In-wall Smart
Dimmer must not exceed 600 watts (Incandescent);
150W dimmable CFL/LED. The Dimmer is
designed only for use with permanently installed fixtures.
Federal Communications Commission (FCC) Statement
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may caus harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between the equipment and
receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
DECLARATION DE CONFORMITE D'INDUSTRIE CANADA
Ce périphérique a été testé et reconnu conforme aux limites spécifiées dans RSS-210.
Son utilisation est soumise aux deux conditions suivantes :
(1) il ne doit pas provoquer d'interférences gênantes et
(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
Getting To Know Your New Z-Wave Device
1.
Must not exceed 600 watts (Incandescent): 1200W (10A) Resistive or ½ HP
Motor. Total load capacity for both outlets is 1200W (10A) Resistive.
• One Z-Wave controlled AC outlet for standard incandescent light, CFL/LED, fans or small appliances
• Remote ON/OFF control via the Z-Wave controller
• Manual ON/OFF control with the front panel push button
• One always-on pass-through AC outlet
• Space efficient design
• Does not block the lower outlet when plugged into the upper outlet of a duplex wall receptacle
(This assumes that the duplex receptacle is mounted with the ground pin down).
• Plugs and cords for connected devices route to the side allowing close placement of furniture
• Grounded 3-wire power connection for safety
2. A. Z-Wave controlled outlet(1channel)
This outlet can remotely turn On/Off the connected device
B. Manual/Program button
Single press — turn the lamp On/Off
Single press — include or exclude in Z-Wave network
C. Z-Wave controlled outlet(2channel)
This outlet can remotely turn On/Off the connected device
3.
1. Plug the light you want to control into the Z-Wave controlled smart outlet
on the wireless switch as indicated by the Z-Wave logo
2. Plug the wireless smart switch directly into an available grounded outlet
(Top outlet recommend if possible).
3.
4.
5.
NOTE: Plug directly into outlet, do not use with extension cords
1. Follow the instructions for your Z-Wave certified controller to include the device
to the Z-Wave network.
2. Once the controller is ready to include your device,single press and release the
manual/program button on the device to include it in the network.
3. Once your controller has confirmed that the device has been included, refresh
the Z-Wave network to optimize performance.
4. The association group supports two nodes and life line function.
Note: Your device may need to be within 10 feet of the controller to be included. If so, include the device to the network
within 10 feet of the controller and relocate it to the desired position in your home. Be sure to refresh the network if the
device is included in this manner.
Please reference the controller/gateway’s manual for instructions.
Now you have complete control to turn your lamp ON/OFF according to groups, scenes, schedules and interactive
automation programmed by your controller. If your Z-Wave certified controller features Remote Access, you can
now control your lighting from your mobile phone devices.
TO return your switch to factory default:
1. If plugged in, unplug the smart switch from the receptacle.
2. Press and hold the top button for at least 3 seconds while you plug the smart
switch into a receptacle.
3. Use this procedure only in the event that the network primary controller is
missing or otherwise inoperable.
Adding device to Z-Wave network:
1. Follow the instructions for your Z-Wave certified controller to include a device
to the Z-Wave network.
2. Once the controller is ready to include your device, press up and release the
toggle to include it in the network.
3. Once your controller has confirmed that the device has been included, refresh
the Z-Wave network to optimize performance.
4. The device is associated in the same group when it included in setting process.
Now you can control your Z-wave device according to groups, scenes, schedules
and automation programmed. If your controller features remote access, you can
now control all devices in Z-Wave network from mobile devices.
To exclude and reset the device
1. Follow the instructions for your Z-Wave certified controller to exclude a device
from the Z-Wave network.
2. Once the controller is ready to Exclude your device, press up and release the
toggle to exclude it from the network.
Our product can be included and operated in Z-Wave network with other certified
devices and/or other applications.
All non-battery nodes within Z-Wave network will act as repeater.
  • Page 1 1
  • Page 2 2

Show Home ZW37 Manuel utilisateur

Marque
Show Home
Modèle
ZW37
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents