Tenda A15 Guide d'installation

A15
Tenda
Marque
Tenda
Modèle
A15
Taper
Guide d'installation
Model: A15
LED Descriptions
Method 1: Extending Your WiFi Network Using Web UI
Quick Installation Guide
AC750 Dual Band WiFi Repeater
Signal LED
Solid blue
Solid red
Off
The repeater does not connect to your WiFi router/
modem.
The repeater is too far away from the router.
Relocate the repeater closer to the router.
The repeater has connected to your existing WiFi
router/modem, and its position is proper.
WPS LED
On
Blinking
Off
A WPS connection has been established.
A WPS connection is being established.
The WPS function is disabled.
PWR LED
Solid on
The repeater has started.
The repeater is starting.
The repeater is not powered on.
Off
Blinking
1
Power on the Repeater
Plug the repeater into a power
outlet near the router in the
same room.
Method 2: Extending Your WiFi Network Using WPS
2 . Wait until the Signal LED on the repeater turns solid blue or red. If not, try Method 1.
2
Extend Your WiFi Network
1. Press the WPS button on the router and within 2 minutes press the WPS button
on the repeater.
Wait until the PWR LED turns
solid blue.
Press
1
Power on the Repeater
Plug the repeater into a power outlet
near the router in the same room.
Wait until the PWR LED turns solid blue.
PWR
PWR
4. Select a WiFi network (SSID) you want to
extend.
5. Enter the password of the WiFi network
you want to extend. Set your repeater's
SSID (optional), and click Extend.
Select a WiFi network you want to
extend…
My_home_wifi
Rescan Switch Mode
Your existing WiFi network
Enter the password of “My_home_wifi”
My_home_wifi_5GEXT
Password of the extended network is
same as your existing WiFi network.
The extended WiFi network
SSID
Back Extend
Password (5-32 characters)
Confirm
Next Not Now
re.tenda.cn
2
Extend Your WiFi Network
1. Connect your WiFi device to the repeater's
WiFi network Tenda_EXT.
WLAN
Tenda_EXT
2. Start a web browser, enter re.tenda.cn or
192.168.0.254 in the address bar to log in.
3. Create a login password for later login
(recommend).
Ensure that the Mobile Data (if any)
function of your WiFi device is disabled.
Wait a moment, the Extended successfully!
page appears.
3
Relocate the Repeater
1. Plug the repeater into an outlet halfway between
the router/modem and the WiFi dead zone.
The location you choose must be within the range
of your existing WiFi network.
2 . Wait until the Signal LED turns blue. If not, relocate
the repeater closer to the router/modem.
4
Connect to the Internet
Connect your WiFi devices to the repeater
using the SSIDs set by yourself, or your
router's/modem's SSID with the suffix _EXT
or _5GEXT, and using the WiFi password
same as your existing WiFi network.
You can use Method 2 if your router/modem has a WPS button, which
may be indicated by , , or . Otherwise, use Method 1.
For better performance, follow the on-screen tips or
the steps below to relocate your repeater.
WiFi router/modem
Signal
Blue: Good connection
Red: Bad connection
A15
Antennas upward
and vertical to the
ground
FAQ
Operating temperature: 0°C~40°C Operating humidity: 10%-90% RH, non-condensing
EIRP Power (Max.):
2.4GHz: 19.5dBm
5GHz: 20.5dBm
Connect your WiFi devices to the extended
network using the SSIDs of your WiFi
router's/modem's SSID with the suffix _EXT
or _5GEXT, and WiFi password same as your
existing WiFi network.
3
Relocate the Repeater
1. For better performance, plug the repeater into an
outlet halfway between the router/modem and
the WiFi dead zone.
The location you choose must be within the range
of your existing WiFi network.
2 . Wait until the Signal LED turns solid blue. If not,
relocate the repeater closer to the router/modem.
4
Connect to the Internet
WiFi router/modem
Signal
Blue: Good connection
Red: Bad connection
A15
Antennas upward
and vertical to the
ground
Q1: I cannot login to the web UI of the repeater. What should I do?
Try the following solutions:
If a WiFi device is used, ensure that your WiFi device has connected
to the repeater's WiFi network Tenda_EXT, and the Mobile Data
(if any) function is disabled.
If a computer is used, ensure that your computer has connected to
the repeater's WiFi network Tenda_EXT, and your computer has set
to Obtain an IP address automatically and Obtain DNS server
address automatically. Or unplug the Ethernet cable.
Reset the repeater, and try again.
Q2: How to reset the repeater?
When the PWR LED of the repeater is solid on, press the RESET button
on the repeater using a paper clip, and release. After the PWR LED
turns solid on, the repeater is restored to the factory settings.
Q3: The repeater cannot find the WiFi network of my router/modem.
What should I do?
Ensure that the WiFi network of your router/modem is enabled and can
be detected by your WiFi device.
Change the channel of your router/modem, and try again.
Change the encryption type of the router/modem to WPA-PSK or
WPA2- PSK, and try again.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to be used in the indoor.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment and it also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference,
it is recommended to use a shielded RJ45 cable.
IC RSS warning
Industry Canada(RSS-Gen Issue 4)
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage;
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
......brouillage est susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre
antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance
minimum de 20 centimètres entre le radiateur et votre corps.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF
exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Operations in the 5.15-5.25GHz band are restricted to indoor use only.
This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
--for PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall
be easily accessible.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment.
(2) To avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type A15
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: http://www.tendacn.com/en/service/download-cata-101.html.
Operate Frequency:
2.4G: EU/2400-2483.5MHz (CH1-CH13)
5G: EU/5150-5250MHz (CH36-CH48)
Software Version: V15.13.07.06
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European directive 2012/19/
EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen,
China. 518052
United States Hotline: 1-800-570-5892
Canada Hotline: 1-888-998-8966
HongKong Hotline: 00852-81931998
Skype: Tendasz
Website: http:// www.tendacn.com
E-mail: [email protected]
Copyright
© 2017 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other
brand and product names mentioned herein are trademarks or registered trademarks of
their respective holders. Specifications are subject to change without notice.
  • Page 1 1
  • Page 2 2

Tenda A15 Guide d'installation

A15
Tenda
Marque
Tenda
Modèle
A15
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents